3-861-541-21 (1) Trinitron Color Computer Display Operating Instructions EN C ® CPD-100GS CPD-200GS © 1998 by Sony Corporation Owner's Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. Serial No. Hinweise · Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). · Aus ergonomischen Gründen (flimmern) sollten nur Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne Zeilensprung) verwendet werden. · Die Konvergenz des Bildes kann sich auf Grund des Magnetfeldes am Ort der Aufstellung aus der korrekten Grundeinstellung verändern. Zur Korrektur empfiehlt es sich deshalb, die Regler an der Frontseite für Konvergenz so einzustellen, daß die getrennt sichtbaren Farblinien für Rot, Grün und Blau bei z.B. der Darstellung eines Buchstabens zur Deckung (Konvergenz) gelangen. Siehe hierzu auch die Erklärungen zu Konvergenz. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Do not open the cabinet. Refer servicing to qualified personnel only. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTICE This notice is applicable for USA/Canada only. If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V NOTICE Cette notice s'applique aux Etats-Unis et au Canada uniquement. Si cet appareil est exporté aux Etats-Unis ou au Canada, utiliser le cordon d'alimentation portant la mention UL LISTED/CSA LABELLED et remplissant les conditions suivantes: SPECIFICATIONS Type de fiche Fiche Nema 5-15 broches Cordon Type SVT ou SJT, minimum 3 × 18 AWG Longueur Maximum 15 pieds Tension Minimum 7 A, 125 V Declaration of Conformity According to 47CFR Parts 2 and 15 for Class B Personal Computers and Peripherals Trade Name: Model No.: Responsible Party: Address: Telephone No.: Sony CPD-100GS and CPD-200GS Sony Electronics Inc. 1 Sony Drive, Park Ridge, NJ. 07656 201-930-6970 As an ENERGY STAR Partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. This device complies with Part 15 of the FCC Rules. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that cause undesired operation. 2 Getting Started TABLE OF CONTENTS Getting started Precautions ........................................................................................................................... Identifying Parts and Controls .......................................................................................... Setup ...................................................................................................................................... Selecting the On-screen Display Language ..................................................................... Connecting Your Monitor's Speaker ................................................................................. 4 5 6 6 7 Customizing Your Monitor Adjusting the Picture Brightness and Contrast ............................................................... 8 Introducing the On-screen Display System ..................................................................... 8 Using the CENTER On-screen Display ............................................................................ 9 Using the SIZE On-screen Display .................................................................................... 9 Using the GEOM (Geometry) On-screen Display ......................................................... 10 Using the ZOOM On-screen Display .............................................................................. 11 Using the COLOR On-screen Display ............................................................................ 11 Using the SCREEN On-screen Display ........................................................................... 12 Using the OPTION On-screen Display ........................................................................... 13 Resetting the Adjustments ............................................................................................... 15 Selecting the Graphic Picture Enhancement (GPE) Mode ........................................... 16 EN F ES Technical Features Preset and User Modes ..................................................................................................... 16 Displaying the monitor's information ............................................................................ 17 Power Saving Function ..................................................................................................... 17 Damper Wires .................................................................................................................... 17 Plug & Play ......................................................................................................................... 17 C Additional Information Warning Messages ............................................................................................................. 18 Troubleshooting ................................................................................................................. 18 Self-diagnosis Function ..................................................................................................... 20 Specifications ...................................................................................................................... 20 · Macintosh is a trademark licensed to Apple Computer, Inc., registered in the U.S.A. and other countries. · Windows® is a registered trademark of Microsoft Corporation in the United States and other countries. · IBM PC/AT and VGA are registered trademarks of International Business Machines Corporation of the U.S.A. · VESA is a trademark of Video Electronics Standard Association. · All other product names mentioned herein may be the trademarks or registered trademarks of their respective companies. · Furthermore, "TM" and "®" are not mentioned in each case in this manual. 3 Getting started Started Precautions Installation · Prevent internal heat build-up by allowing adequate air circulation. Do not place the monitor on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. · Do not install the monitor near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. · Do not place the monitor near equipment which generates magnetism, such as a transformer or high voltage power lines. Warning on power connection · Use an appropriate power cord for your local power supply. · Before disconnecting the power cord, wait at least 30 seconds after turning off the power to allow the static electricity on the CRT display surface to discharge. · After the power has been turned on, the CRT is demagnetized (degaussed) for about 5 seconds. This generates a strong magnetic field around the metal frame, which may affect the data stored on magnetic tapes and disks near the bezel. Place magnetic recording equipment, tapes and disks away from this monitor. The outlet should be installed near the equipment and be easily accessible. Maintenance · Clean the cabinet, panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzine. · Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube. · Clean the screen with a soft cloth. If you use a glass cleaning liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the screen's coating. Transportation When you transport this monitor for repair or shipment, use the original carton and packing materials. Use of the Tilt-Swivel With the tilt-swivel, this monitor can be adjusted to the desired angle within 180° horizontally and 20° vertically. To turn the monitor vertically and horizontally, hold it at the bottom with both hands as illustrated below. 15° 90° 90° 5° 4 Getting Started Getting Started Identifying Parts and Controls See the pages in parentheses for further details. Front Rear 1 MUTING button (page 7) Mutes the sound. 8 AC IN connector Provides AC power to the monitor. 2 RESET button (page 15) Resets the adjustments to the factory settings. 9 Video input connector (HD15) Inputs RGB video signals and SYNC signals. EN F 3 GPE button (page 16) Selects the Graphic Picture Enhancement (GPE) mode. Side ES C 4 MENU button (pages 7 -15, 17) Displays the MENU OSD. 5 > (contrast) (?//) buttons (pages 7 ­ 15, 20) Adjust the contrast. Function as the (?//) buttons when adjusting other items. AUDIO IN 6 ¨ (brightness) (./>) buttons (pages 7 ­ 15) Adjust the picture brightness. Function as the (./>) buttons when adjusting other items. !º AUDIO IN jack Inputs audio signals when connected to the computer's audio out jack. 7 u (power) switch and indicator (pages 17, 20) Turns the monitor on or off. The indicator lights up in green when the monitor is turned on, and either flashes in green and orange or lights up in orange when the monitor is in power saving mode. !¡ 2 Headphones jack Outputs audio signals to headphones (not supplied). 5 Getting Started About the supplied Macintosh adapter Setup Before using this monitor, check that the following items are included in your carton: · Monitor (1) · Power cord (1) · Macintosh adapter (1) · Windows® 95 Monitor Information Disk and its manual (1) · Warranty card (1) · These operating instructions (1) · Audio miniplug cord (1) This monitor works with any IBM or compatible system equipped with VGA or greater graphics capability. Although this monitor works with other platforms running at horizontal frequencies between 30 and 70 kHz (CPD100GS), 30 and 85 kHz (CPD-200GS), including Macintosh and Power Macintosh systems, a cable adapter is required. Please consult your dealer for advice on which adapter is suitable for your needs. The supplied Macintosh adapter is compatible with Macintosh LC, Performa, Quadra and Power Macintosh series computers. Macintosh II series and some older versions of Power Book models may need an adapter with micro switches (not supplied). Note Do not short the pins of the video signal cable. Step 2: Connect the power cord With the monitor switched off, connect one end of the power cord to the monitor and the other end to a power outlet. to a power outlet to AC IN Power cord (supplied) Step 1: Connect the monitor to the computer Connecting to an IBM PC/AT, Macintosh or compatible computer With the computer switched off, connect the video signal cable to the computer's video output. Step 3: Turn on the monitor and computer The installation of your monitor is complete. Note If "OUT ...