User manual FUJITSU SIEMENS SCENIC P300 (I845GE) - annexe 3

Mainboard D1522 / D1521 Deutsch / English / Français answers 2 Technisches Handbuch / Technical Manual Sie haben ... ... technische Fragen oder Probleme? Wenden Sie sich bitte an: · Ihren zuständigen Vertriebspartner · Ihre Verkaufsstelle Aktuelle Informationen und Updates (z. B. BIOS-Update) zu unseren Mainboards finden Sie im Internet: http://www.fujitsu-siemens.com/mainboards Are there ... ... any technical problems or other questions you need clarified? Please contact: · your sales partner · your sales outlet The latest information and updates (e.g. BIOS update) on our mainboards can be found on the Internet under: http://www.fujitsu-siemens.com/mainboards Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.: A26361-D1522-Z120-1-6319 Printed in the Federal Republic of Germany AG 0103 01/03 A26361-D1522-Z120-1-6319 Deutsch English Mainboard D1522 / D1521 Français Technisches Handbuch Technical Manual Ausgabe Januar 2003 January 2003 edition Intel, Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt. Alle Rechte vorbehalten, insbesondere (auch auszugsweise) die der Übersetzung, des Nachdrucks, der Wiedergabe durch Kopieren oder ähnliche Verfahren. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte vorbehalten, insbesondere für den Fall der Patenterteilung oder GM-Eintragung. Liefermöglichkeiten und technische Änderungen vorbehalten. Dieses Handbuch wurde erstellt von cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de Copyright Fujitsu Siemens Computers GmbH 2003 Intel, Pentium and Celeron are registered trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged. All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability. Right of technical modification reserved. This manual was produced by cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de Übersicht/Overview Mainboard D1522 / D1521 Interne Anschlüsse und Steckplätze / Internal connectors and slots 1= 2= 3= 4= 5= 6= 7= 8= 9= 10 = 11 = 12 = 13 = 14 = 15 = 16 = 17 = 18 = 19 = 20 = 21 = Stromversorgung / Power Supply Diskettenlaufwerk / Floppy disk drive IDE-Laufwerke 3/4 / IDE-drives 3/4 Stromversorgungsüberwachung / Power supply monitoring Bedienfeld / Front panel Schalter / Switch Steckbrücken / Jumper IDE-Laufwerke 1/2 / IDE-drives 1/2 Batterie / Battery Lüfter 2 / Fan 2 Power On LED II Gehäuseüberwachung / Intrusion LCD-Statusanzeige / LCD status indicator USB C/D USB E/F Serielle Schnittstelle 2 / serial interface 2 S/PDIF Anschluss / S/PDIF connector Audio-Bedienfeld / Audio front panel CD-Audio in Stromversorgung Prozessor / Processor power supply Lüfter 1 / Fan 1 21 DIMM 1 DIMM 2 CPU Pentium 4 1 2 3 4 20 5 6 7 8 9 AGP 19 18 17 PCI 1 PCI 2 PCI 3 10 16 14 13 11 15 12 Optionale Komponenten / Optional components Externe Anschlüsse / External connectors LAN AUDIO Bedienfeld / Front panel Power On/Off Message LED Sleep LED 1) Power On Sleep 1) HD-LED LED 1) 3) 1) Reset 1 2 SCSI LED Input 1) 2) Speaker 1) Cable is not included in the delivery scope. 2) The same interface 3) 2pin or 3pin connector possible PowerOn LED II 1) 3) 1 3 A26361-D1522-Z120-1-6319 Umschlag/Cover Contents Mainboard D1522 / D1521................................................................................................................1 Notational conventions ..............................................................................................................1 Important notes..................................................................................................................................2 Information about boards ...........................................................................................................2 List of features...................................................................................................................................3 Special technical features ­ special features .............................................................................4 Brief instructions on installing mainboard ....................................................................................6 Prior to installation .....................................................................................................................6 Interfaces and connectors ..............................................................................................................8 External ports ....................................................................................................................................8 Internal ports and connectors ............................................................................................................9 Hard disk connection .................................................................................................................9 Pin assignment of internal ports.......................................................................................................10 Settings with switches and jumpers ............................................................................................15 Add-on modules / Upgrading........................................................................................................16 Installing and removing processors..................................................................................................16 Installing the processor with heat sink and fan.........................................................................16 Upgrading main memory..........................................................................................................18 Upgrading AGP screen controllers...................................................................................................19 Adding PCI cards.............................................................................................................................19 PCI bus interrupts - Selecting correct PCI slot .........................................................................20 Replacing lithium battery..........................................................................................................21 BIOS update....................................................................................................................................22 BIOS Recovery - Recovering System BIOS ....................................................................................23 Microcode Update ...........................................................................................................................23 Drivers .............................................................................................................................................24 Annex .............................................................................................................................................25 Electrical Properties.........................................................................................................................25 Loadability for connections and fuses ......................................................................................25 Mainboard current requirement ................................................................................................25 APM and ACPI system status, energy-saving modes......................................................................26 Mainboard Revision and BIOS Version............................................................................................27 Error messages .............................................................................................................................28 DOS error messages .......................................................................................................................31 SmartCard reader - error messages ................................................................................................32 Glossary ..........................................................................................................................................33 A26361-D1522-Z120-3-6319 Mainboard D1522 / D1521 Your mainboard is available in different configuration levels. Depending on the configuration chosen, some of the hardware components described may not be available on your mainboard. Further information Information on the BIOS Setup and additional descriptions of the drivers are contained: · · · in the readme files on your hard disk on the driver floppy disks included on the CD "Drivers & Utilities Collection" or "Drivers & Utilities" or "ServerStart". i The programme Acrobat Reader must be installed to be able to open the manuals. You may find the programme on the CD-ROM directory: utls/acrobat. For more details please read the according readme.txt files. Notational conventions The meanings of the symbols and fonts used in this manual are as follows: ! i Ê Ë Ú indicates information which is important for your health or for preventing physical damage. indicates additional information which is required to use the system properly. Text which follows this symbol describes activities that must be performed in the order shown. This symbol indicates that you must enter a blank space (press the Space Bar) at this point. This symbol indicates that you must press the Enter key. Text in this typeface indicates screen outputs. Text in this bold typeface indicates the entries you make via the keyboard. Text in italics indicates commands or menu items. "Quotation marks" indicate names of chapters or terms. A26361-D1522-Z120-3-6319 English - 1 Mainboard D1522 / D1521 Important notes With the mainboard installed you must open the system to access the mainboard. How to dismantle and reassemble the system is described in the operating manual accompanying the system. Connecting cables for peripherals must be adequately shielded to avoid interference. ! Observe the safety notes in the operating manual of your system. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Add-on modules / Upgrading" - "Replacing lithium battery" section. Components can become very hot during operation. Ensure you do not touch components when making extensions to the mainboard. There is a danger of burns! The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the manual for the receiving device. i The warranty is invalidated if the system is damaged during the installation or replacement of expansions. Information on which expansions you can use is available from your sales outlet or the customer service centre. Information about boards To prevent damage to the mainboard, the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the mainboard, or any other components, for example EMI spring contacts. Remove the plug from the mains outlet so that system and mainboard are totally disconnected from the mains voltage. Be careful with the locking mechanisms (catches, centring pins etc.) when you replace the mainboard or components on it, for example memory modules or processors. Never use sharp objects (screwdrivers) for leverage. Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown. When you handle boards fitted with ESDs, you must, under all circumstances, observe the following: · · · · · You must always discharge static build up (e.g. by touching a grounded object) before working. The equipment and tools you use must be free of static charges. Remove the power plug from the mains supply before inserting or removing boards containing ESDs. Always hold boards with ESDs by their edges. Never touch pins or conductors on boards fitted with ESDs. 2 - English A26361-D1522-Z120-3-6319 Mainboard D1522 / D1521 List of features Onboard features Chipset Board size VGA Audio Buzzer / int. Speaker Support LAN / with Alert-on-LAN HI-SPEED USB 2.0 SmartCard Reader Support (USB / serial) Temperature monitoring System Monitoring Fujitsu Siemens Computers Keyboard Power Button Support Internal ports DIMM Sockets (DDR SDRAM, PC2100/1600) AGP Slot (2/4x, 32 bit, 66 MHz, 1.5 V) PCI slot (32 bit, 33 MHz, 5 V and 3.3 V) CNR Slot (Type A, AC`97 only) IDE Interface (Ultra DMA/100) Floppy Interface (up to 2.88 MB) S/PDIF* (digital audio) CD / AUX audio input Frontpanel Audio (headphone, microphone) Wake On LAN USB Ports* (2.0, ~480 Mb/s) Serial Ports* (FIFO, 16550 compatible) Fan Connectors PSU** / FAN1 / FAN2 / FAN3 SMBus Connector* (Case Temperature) Intrusion Connector* (Case Open) Power Connectors ATX / ATX12V / AGP PRO 2 1 3 2 1 1 1/1 4 1 1/1/1/1 1 1/1/2 1 3 2 1 1 1/1 4 1 -/1/1/1/1/D1522-A i845GE µ-ATX ! ! -/! !/! ! !/! ! ! D1521-A i845GE µ-ATX ! ! -/! !/! -/! A26361-D1522-Z120-3-6319 English - 3 Mainboard D1522 / D1521 External ports VGA Audio Mic. in / Line in / Line out (2 x 0,5 W / 8 ) Game/MIDI LAN (RJ-45) PS/2 mouse/keyboard USB Ports (2.0, ~480 Mb/s) Serial Ports (FIFO, 16550 compatible) Parallel Port (EPP/ECP) * for use with internal devices or optional Front or Rear panel ** not supported by standard power supplies 1 1/1/1 1 1/1 2 1 1 1 1/1/1 1 1/1 2 1 1 Special technical features ­ special features Your mainboard is available in different configuration levels. Depending on the configuration, your mainboards is equipped with or supports the features described in the following. Thermal Management and System Monitoring A microcontroller developed by Fujitsu Siemens Computers reliably protects your PC against damage caused by overheating. Overheating can lead to the data loss or processor damage. An ingenious fan control and monitoring system prevents unnecessary noise. Should the processor nevertheless become too hot at the maximum fan speed, then the processor clock rate will automatically be reduced so that the system continues to run stably. In addition, the microcontroller offers monitoring of, for example, system voltages (12 V, 5 V, CMOS), opening of the case and a watchdog function. The microcontroller operates independently of the operating system and the processor. All values are displayed with DeskView, DeskViewOEM or SystemGuard. You can reduce the noise resulting when the hard disk is accessed to a barely perceptible level. The resulting power decrease is approx. 10-20% depending on the hard disk. A password assignment for the hard disk is only possible with suitable, newer hard disks and prevents unauthorised access to the stored data. Silent Mode and Harddisk Password are activated in the BIOS Setup. Additional information is contained in the "BIOS Setup" manual. 4 - English A26361-D1522-Z120-3-6319 Mainboard D1522 / D1521 Logo Boot A customer-specific logo can be displayed during system booting. The logo is loaded using the LogoFlash tool. The logo can have a size of 640 x 480 pixels with 16 colours. The tool is provided on the CD "Drivers & Utilities" or "Drivers & Utilities enhanced" or is available on the Internet at http://www.fujitsu-siemens.com/mainboards. DeskView / DeskViewOEM The network-capable manageability software DeskView/DeskViewOEM* mainly consists of three modules: · · · Recovery BIOS DeskInfo shows the most important device data of the PCs in a network (local and/or on an administrator PC). DeskAlert monitors the operability of all major components and triggers alarms if necessary depending on the mainboard variant. DeskFlash carries out a BIOS update under Windows. If an error occurs during a BIOS update (e.g. due to a power failure), the system BIOS will be destroyed. All Fujitsu Siemens Computers mainboards are equipped with a recovery BIOS. With it a destroyed BIOS can easily be restored. Exact instructions are provided in the chapter "BIOS Recovery - Recovering System BIOS". IA-PC Instantly Available PC ensures fast availability of the PC from an energy-saving mode. Within just a few seconds the PC is in exactly the same state it was in when it was switched off without time-consuming booting. Depending on the operating system, the PC can be switched into an energy-saving mode with applications open by pressing the ON/OFF switch. A26361-D1522-Z120-3-6319 English - 5 Brief instructions on installing mainboard Brief instructions on installing mainboard If you have purchased a separate mainboard, you can install the mainboard in your system in accordance with the following brief instructions. The activities described here assume a basic knowledge of PCs and cannot be carried out by a layperson. If you are not sure whether you have the necessary specialised knowledge, then leave this work to an expert. The illustrations of the system show examples of possible cases. Prior to installation Ê Ê Please take note of the safety information in the "Important notes" chapter. Check whether the processor, memory modules and power supply are suitable for this mainboard: - - - (see "Installing and removing processors" chapter). (see "Upgrading main memory" chapter). (see "Electrical Properties" chapter). Ê Ê Make sure the current requirement of the fans (processor, case) does not exceed the loadability of the fan connections (see chapter entitled "Electrical Properties"). First only install the components absolutely necessary (graphics card, processor and heat sink, one memory module) and only connect the required connections (power supply unit, case connections such as ATX on/off switch, hard disk or floppy disk drive). You should not install additional cards and devices until this minimum configuration successfully boots (see chapter entitled "Add-on modules / Upgrading". Installation Ê Equip the mainboard with the processor, heat sink and memory modules before installation if possible. Further information can be found in "Installing and removing processors" chapter. Ê Open the casing as described in the operating manual. 6 - English A26361-D1522-Z120-3-6319 Brief instructions on installing mainboard Ê Should no suitable connection field be provided in the case, then you must install the connection field (1) provided. Ensure the plate is aligned properly so that the connections are suitable for the mainboard later. Ê Set the mainboard on the edge on which the connection field is located (2) and then insert the board in the case (3). Make sure that spacers in the housing are only mounted at points at which there are mounting holes in the mainboard. Ê Fasten the mainboard with the screws. Ê Connect the plugs for the power supply, control panel and drives to the corresponding connections on the mainboard. Driver installation Ê Install the drivers for the chipset. You may find the driver on the "Drivers & Utilities" CD. Please refer to chapter "Drivers" for a description of installing drivers. A26361-D1522-Z120-3-6319 English - 7 Interfaces and connectors Interfaces and connectors The positions of the interfaces and connectors are shown on page "Cover". The components and connectors marked are not necessarily present on the mainboard. External ports The positions of the external ports are shown on page "Cover". PS/2 keyboard port, purple PS/2 mouse port, green Serial interface, turquoise Parallel port/Printer, burgundy LAN LAN connector USB - Universal Serial Bus, black Audio output (Line out), light green Audio input (Line in), light blue Microphone jack (mono), pink VGA port, blue (monitor) LAN connector This mainboard is equipped with the 82562ET (D1521) or the 82562EM (D1522) LAN controller. Both LAN controller support transfer speeds of 10 Mbit/s and 100 Mbit/s. The LAN controller are equipped with a 3 KB transmission and receiving buffer (FIFO) and support WOL function through Magic Packet. It is also possible to boot a device without its own boot hard disk via LAN. Here bootix® LAN BootP or bootix® PXE are supported. The LAN RJ45 connector has two LEDs (light emitting diodes). 1 = a connection exists (e.g. to a hub). 2 = Link Mode: the LAN connection is active. WOL mode: a Magic PacketTM is being received. 2 1 8 - English A26361-D1522-Z120-3-6319 Interfaces and connectors Graphics port - Supported screen resolutions Depending on the operating system used, the screen resolutions in the following table refer to the mainboard screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the operating manual or technical manual supplied with the controller. Screen resolution 640 x 480 800 x 600 1024 x 768 1280 x 1024 1600 x 1200 1920 x 1440 2048 x 1536 Refresh rate (Hz) 120 120 100 100 100 75 60 bpp 32 32 32 32 32 32 32 Colour 32 bit 32 bit 32 bit 32 bit 16 bit 16 bit 16 bit Internal ports and connectors The positions of the internal ports and connectors are shown on the Cover. Additional information on some ports is also provided here. Hard disk connection An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for the ultra ATA/66 or ultra ATA/100 mode. Ê Connect the end of the cable marked with blue to the mainboard. A26361-D1522-Z120-3-6319 English - 9 Interfaces and connectors Pin assignment of internal ports The pin assignment of some internal connections is shown in English in the following. i Some of the following connectors may be optional! Front panel Watch the poling of the LEDs. The positive pole of the connection cables is often indicated with a coloured wire. Power On/Off Message LED Sleep LED 1) Power On Sleep 1) HD-LED LED 1) 3) 1) Reset 1 2 SCSI LED Input 1) 2) Speaker 1) Cable is not included in the delivery scope. 2) The same interface 3) 2pin or 3pin connector possible Connection Reset Sleep Power On/Off HD LED SCSI Activity Input Message LED Power On LED Speaker Sleep LED Note This connection is reserved for future use. Attention: Do not connect to the LED connections of an SCSI controller! This connection is intended for a cable with a 4-pin connector. An SCSI controller reports activity (low-active) via this cable. Indicates the system state APM or ACPI together with the Sleep LED (see chapter entitled "APM and ACPI system status, energy-saving modes"). 0,5 W at 8 Ohm Indicates the system state APM or ACPI together with the Power-On LED (see chapter entitled "APM and ACPI system status, energy-saving modes"). 10 - English A26361-D1522-Z120-3-6319 Interfaces and connectors Power On LED II 1 3 Pin 1 2 3 Note Power On LED (Anode) Power On LED (Anode) Power On LED (Cathode) Power supply ATX 1 11 Pin 1 2 3 4 5 6 7 8 9 10 Signal +3.3 V (P3V3P) +3.3 V (P3V3P) GND +5 V (VCC) GND +5 V (VCC) GND Powergood (high asserted) +5 V Auxiliary (VCC Aux) +12 V (P12VP) Pin 11 12 13 14 15 16 17 18 19 20 Signal +3.3 V (P3V3P) -12 V (P12VN) GND PS on (low asserted) GND GND GND -5 V (P5VN) +5 V (VCC) +5 V (VCC) 1 Power control (system monitoring) Pin 1 2 3 4 5 6 7 8 Signal AC Outlet (high asserted) PS FAN Control (PS FAN C max. 3 mA) Reserved PS FAN Sense SMB CLK SMB DATA VCC EEPROM (+3.3 V) GND A26361-D1522-Z120-3-6319 English - 11 Interfaces and connectors Fan 1 (system fan - supervised) Pin 1 2 3 1 Signal GND Controlled Fan voltage (0 V, +6 V ... +12 V, max. 1 A) or fix Fan voltage (+12 V, max. 1 A) Fan sense Fan 2 (system fan - supervised) Pin 1 2 3 Signal 1 GND Controlled Fan voltage (0 V, +6 V ... +12 V, max. 1 A) or fix Fan voltage (+12 V, max. 1 A) Fan sense LCD status indicator (for use with optional front panel) 2 1 Pin 1 3 5 7 9 11 13 Signal SMB CLK SMB DATA Key LAN Active Icon Harddisk Action Icon Message Icon Power Icon Pin 2 4 6 8 10 12 14 Signal GND GND RFU Reserved for Future Use LAN Link Icon BMC Alert Icon Sleep Icon P3V3P DUAL 12 - English A26361-D1522-Z120-3-6319 Interfaces and connectors USB C/D / E/F - dual channel (internal or external via special wire) 1 11 2 12 Pin 1 3 5 7 9 11 Signal Key VCC C Data negative C Data positive C GND Key Pin 2 4 6 8 10 12 Signal Chipcard reader on VCC D Data negative D Data positive D GND Not Connected Intrusion for case open detect for optional push-button (opener) 1 Pin 1 2 3 Signal GND Case open (low asserted) Intrusion switch present (low asserted) Audio S/PDIF (2-pin) 1 Pin 1 2 Signal GND SPDIF out A26361-D1522-Z120-3-6319 English - 13 Interfaces and connectors Audio S/PDIF (3-pin) 1 Pin 1 2 3 Signal GND SPDIF out GND Audio front panel 1 2 Pin 1 3 5 7 9 Signal Micro input Micro bias Right line output NC Left line output Pin 2 4 6 8 10 Signal Analog GND Analog VCC Right line return Key Left line return CD-ROM audio 1 Pin 1 2 3 4 Signal Left CD audio input CD GND CD GND Right CD audio input Processor power supply 3 1 Pin 1 3 Signal GND GND Pin 2 4 Signal +12 V +12 V 14 - English A26361-D1522-Z120-3-6319 Settings with switches and jumpers Settings with switches and jumpers Your mainboard is equipped with switches or jumpers. The positions of the switches or jumpers are shown on page "Cover". ON 1234 Switch 1 = Skipping system and BIOS Setup password Switch 2 = System BIOS recovery Switch 3 = must always be set to off Switch 4 = must always be set to off 1 2 Pinpair 1 inserted = Skipping system and BIOS Setup password Pinpair 2 inserted = System BIOS recovery Any other setting = State of supply; jumper has no function i The clock frequency of the processor is set automatically. Skipping system and BIOS Setup password - switch 1 / pinpair 1 Switch 1 enables skipping the system and BIOS Setup password. On Off System and BIOS Setup password are skipped when the device is switched on and may be changed. System and BIOS Setup password must be entered when the device is switched on. Recovering System BIOS - switch 2 / pinpair 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (see "BIOS update" chapter). On Off The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the mainboard. Normal operation (default setting). Reserved - switch 3 and switch 4 Switch 3 and 4 are reserved. A26361-D1522-Z120-3-6319 English - 15 Add-on modules / Upgrading Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter! Even when you have switched off the device, parts (e.g. memory modules, AGP and PCI extension boards) are still supplied with power. Installing and removing processors Technical data Intel Pentium 4 with 400 or 533 MHz front side bus in the mPGA478 design. A current list of the processors supported by this mainboard is available on the Internet at: www.fujitsu-siemens.de/mainboards. Installing the processor with heat sink and fan Ê Remove the fan that there may be and the heat sink. 3 2 4 5 1 A Ê Ê Ê Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Remove the old processor from the socket (3). Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). i Ê The angled corner of the processor can also be at a different location than shown in the illustration. Push the lever back down until it clicks into place (5). 16 - English A26361-D1522-Z120-3-6319 Add-on modules / Upgrading Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. Otherwise you must apply a very thin layer of heat conducting paste. Heat conducting pads can only be used once. If you remove the heat sink, you must clean it and apply new heat conducting paste before you remount it. Please note that, depending on the heat sink used, different heat sink mounts are required on the mainboard. i If a counter-plate is mounted on the underside of the mainboard for reinforcement, no heat sinks of the type "Intel Boxed" may be used. Otherwise the retaining clips of the heat sink will be damaged. When using an "Intel Boxed" heat sink, the mainboard must be converted. This conversion set is either included with the mainboard or is available separately. If no counter-plate is mounted, you can use both "Intel Boxed" heat sinks and standard heat sinks. If you use the "Intel Boxed" heat sink, the mainboard will bend due to the high pressure of the retaining clips. This behaviour is specified by Intel. Ê Depending on the configuration variant, you must pull a protective foil off the heat sink or coat the heat sink with heat conducting paste before fitting it. Depending on the processor variant, clips may also be supplied for mounting the heat sink that fix it in place. When you have mounted the optional fan, connect the fan plug to the corresponding connection on the mainboard. Ê Ê A26361-D1522-Z120-3-6319 English - 17 Add-on modules / Upgrading Upgrading main memory Technical data Technology: Total size: Granularity: DDR 266 or DDR 333 unbuffered DIMM modules 184-pin; 2.5 V; 64 Bit, no ECC 128 Mbytes up to 2 Gbyte DDR-SDRAM 32, 64, 128, 256, 512 or 1024 Mbyte for one socket A current list of the memory modules recommended for this mainboard is available on the Internet at: www.fujitsu-siemens.de/mainboards. At least one memory module must be installed. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2,5 V memory modules. Buffered memory modules are not supported. DDR-DIMM memory modules must meet the PC2100 or PC2700 specification. Installing a memory module 2 2 Ê Ê Ê Push the holders on each side of the memory compartment outwards. Insert the memory module into the location (1). At the same time flip the lateral holders upwards until the memory module snaps in place (2). 18 - English A26361-D1522-Z120-3-6319 Add-on modules / Upgrading Removing a memory module 1 1 Ê Ê Push the clips on the right and left of the compartment outward (1). Pull the memory module from the compartment (2). Upgrading AGP screen controllers Technical data: The AGP slot supports the modes 1x/2x/4x with 32 bits and 66 MHz. Only 1.5 V AGP screen controllers are supported. i Some older 3.3 V AGP screen controllers are coded like 1.5 V AGP screen controllers. The installation of such 3.3 V AGP screen controllers can cause serious damage to the mainboard and the AGP screen controller. Adding PCI cards Technical data: 32 bit / 33 MHz PCI slots 5 V and 3.3 V supply voltage 3.3 V auxiliary voltage A26361-D1522-Z120-3-6319 English - 19 Add-on modules / Upgrading PCI bus interrupts - Selecting correct PCI slot i To achieve optimum stability, performance and compatibility, avoid the multiple use of ISA IRQs or PCI IRQ Lines (IRQ sharing). Should IRQ sharing be unavoidable, then all involved devices and their drivers must support IRQ sharing. PCI IRQ Lines connect AGP slots, PCI slots and onboard components to the interrupt controller. PCI IRQ Lines are permanently wired on the mainboard. Which ISA IRQs are assigned to the PCI IRQ Lines is normally automatically specified by the BIOS (see description in "BIOS Setup"). Monofunctional expansions cards: Standard AGP and PCI expansion cards require a maximum of one interrupt, which is called the PCI interrupt INT A. Expansion cards that do not require an interrupt can be installed in any desired slot. Multifunctional expansion cards or expansion cards with integrated PCI-PCI bridge: These expansion cards require up to four PCI interrupts: INT A, INT B, INT C, INT D. How many and which of these interrupts are used is specified in the documentation provided with the card. The assignment of the PCI interrupts to the PCI IRQ Lines is shown in the following table: Onboard controller PCI INT LINE 1 (A) 2 (B) 3 (C) 4 (D) 5 (E) 6 (F) 7 (G) 8 (H) USB 1,1 1st A 2nd A 3rd A USB 2,0 A SMB us A AC97 Audio A Modem A LAN A AGP A B PCI slot 1 A B C D 2 A B C D 3 A B C D - Use the first PCI slots that have a single PCI IRQ Line (no IRQ sharing). If you must use another PCI slot with IRQ sharing, check whether the expansion card properly supports IRQ sharing with the other devices on this PCI IRQ Line. The drivers of all cards and components on this PCI IRQ Line must also support IRQ sharing. 20 - English A26361-D1522-Z120-3-6319 Add-on modules / Upgrading Replacing lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. ! Incorrect replacement of the lithium battery may lead to a risk of explosion! The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste. Make sure that you insert the battery the right way round. The plus pole must be on the top! The lithium battery holder exists in different designs that function in the same way. 2 3 3 2 1 3 Ê Ê Ê Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the holder (1). Remove the battery (2). Insert a new lithium battery of the same type into the socket (3). A26361-D1522-Z120-3-6319 English - 21 Add-on modules / Upgrading BIOS update When should a BIOS update be carried out? Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. In addition, new BIOS functions can also be integrated. A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software. Where can I obtain BIOS updates? The BIOS updates are available on the Internet at www.fujitsu-siemens.de/mainboards. How does a BIOS update work? You have two ways of doing this: 1. BIOS update under DOS with bootable BIOS update floppy disk - brief description Ê Ê Ê Ê Ê Ê Download the update file from out website to your PC. Insert an empty floppy disk (1.44 MB). Run the update file (e.g. 1522103.EXE). A bootable update floppy disk is created. Leave this floppy disk in the drive. Restart the PC. Follow the instructions on screen. i Detailed information on the BIOS update under DOS is provided in the manual on "BIOS Setup" ("Drivers & Utilities" CD). 2. BIOS update under Windows with DeskFlash utility A BIOS update can also be carried out directly under Windows with the DeskFlash utility. DeskFlash is located on the "Drivers & Utilities" CD (from CD version 2001.05 with DeskViewOEM V5.0). In the "Readme" file in the subfolder DeskFlash you will find the installation instructions for DeskFlash. Further information on DeskFlash is provided in the file "DeskView.PDF" and in the DeskViewOEM online help. 22 - English A26361-D1522-Z120-3-6319 Add-on modules / Upgrading BIOS Recovery - Recovering System BIOS i Ê Ê Ê Ê Ê All BIOS settings are reset to the default values. Open the casing as described in the operating manual. Set the switch for "Restore system BIOS" to ON or plug the corresponding jumper (see "Settings with switches and jumpers" chapter). Close the casing as described in the operating manual. Insert a BIOS update floppy disk and start the PC. Note the signals issued from the loudspeaker. You have successfully restored the BIOS if you hear the signal sequence "short-short- long- long- long" and the diskette access indicator is dark. This can take a few minutes. Open the casing as described in the operating manual. Set the switch for "Restore system BIOS" to OFF or remove the corresponding jumper (see "Settings with switches and jumpers" chapter. Close the casing as described in the operating manual. Remove the floppy disk from the drive. Start the PC and invoke BIOS Setup. Select the menu item Reset Configuration in the menu Advanced and change the setting to Yes. Save the change and terminate BIOS Setup. Ê Ê Ê Ê Ê Ê Ê The BIOS recovery has now been completed. The system restarts. i Detailed information on the BIOS recovery is contained in the manual "BIOS Setup" ("Drivers & Utilities" CD). Microcode Update What is a microcode update? As there are no drivers for processors, Intel offers the possibility from the P6 family (Pentium Pro) on to update the command set (microcode) of the processor. This enables minor errors to be corrected and the performance to be increased. To guarantee the best possible performance and error-free operation, Intel recommends updating the microcode regularly. Intel refers to the use of the processor without regular microcode updates as operation outside the specifications. A26361-D1522-Z120-3-6319 English - 23 Add-on modules / Upgrading Safety for processor on Fujitsu Siemens Computers mainboards If the processor uses an old or incorrect microcode, error-free operation cannot be ensured. Fujitsu Siemens Computers has therefore implemented a function on its mainboards that interrupts the booting process if no suitable microcode is available for the installed processor. The output error message is Patch for installed CPU not loaded. Please run the bios flash update diskette. This message appears until the microcode update has been carried out. If the computer is nevertheless operated without a microcode update, error-free operation is not ensured. When should a microcode update be carried out? A microcode update should be carried out in the following cases: · Following installation of a new processor · When a new microcode update is issued. In contrast to the BIOS update, only an updated version of the processor command set is stored. The system BIOS remains unaffected by this. Microcode update under DOS with bootable microcode update floppy disk - brief description Ê Ê Ê Ê Ê Ê Download the update file from out website to your PC. Insert an empty floppy disk (1.44 MB). Run the update file under DOS (e.g. 1495101.EXE). A bootable update floppy disk is created. Leave the floppy disk in the drive. Restart the PC. Follow the instructions on screen. To determine whether the latest microcode update has been loaded, the so-called Patch-ID of the processor can be read out. Ê Press the [F1] key in the BIOS Setup. The entry CPU / Patch ID is shown on the displayed information page. A list with the current processors and the related Patch-IDs is available on the Internet. i If the processor is not recognised, you also require the microcode update tool for processors of the P6 family. Drivers Only when no drivers are installed on your system, or you want to update these, proceed as follows: Ê Ê Ê Ê Insert the CD "Drivers & Utilities Collection" into the CD ROM drive. If the CD does not start automatically, run the START.EXE programme in the main directory of the CD. Select DeskUpdate - Fully automatic installation. Follow the screen instructions. 24 - English A26361-D1522-Z120-3-6319 Annex Annex Electrical Properties Loadability for connections and fuses i 1 Make sure that the connected devices do not overload the connections. Fuse No. Fuse 750 mA Connection Keyboard Mouse VGA connector USB port A USB port B USB port C USB port D USB port E USB port F Maximum loadability Not specified Not specified Minimum 50 mA 500 mA 500 mA 500 mA 500 mA 500 mA 500 mA 2 3 4 5 6 7 500 mA 500 mA 500 mA 500 mA 500 mA 500 mA The fuses on this mainboard can be used several times (polyfuses). Shortly after the error state has been eliminated, the fuses reset to the original state. Mainboard current requirement You require a Pentium4 power supply nit as per the ATX12V specification for this mainboard. If you do not have a PC from Fujitsu Siemens Computers, make sure that the power supply unit provides the required amperages. Source ATX12V power supply ATX12V power supply ATX12V power supply ATX12V power supply Standby voltage of power supply unit Voltage +12 V -12 V +5,0 V +3,3 V +5.0 V SB Maximum difference ±5 % ±10 % ±5 % ±5 % ±5 % Maximum current 3 -6 (8) A 0,05 A 0,9 A 2,2 (3,4) A 0.35 (2) A The specifications apply to the onboard components and represent the least favourable case. In addition, at least 350 mA is required for PCI on 3.3 V, and 500 mA per connected device for USB on 5 V. A26361-D1522-Z120-3-6319 English - 25 Annex APM and ACPI system status, energy-saving modes System status Normal operation Simple energysaving mode Maximum energy-saving mode ** "Save to DRAM" Maximum energy-saving mode "Save To Disk" "Soft Off" Mechanically Off G2 G3 S5 Soft Off Off Off Nearly zero Zero Full boot time Full boot time S4 Wake-up components ca. 20s ACPI Status* G0 G1 S0 S1 APM Status On Standby Power LED To Off Sleep LED Off To Power consumption Normal Almost like normal RAM, wake-up components Almost immediate ly ca. 5s Wake-up time S3 * G = Global status; S = System status ** The power supply unit must provide sufficiently loadable 5 V standby voltage. To use the WOL functionality the power supply must provide a 5 V auxiliary voltage (5VSB) of at least 1 A. 26 - English A26361-D1522-Z120-3-6319 Annex Mainboard Revision and BIOS Version The compatibility, e.g. with new processors, can be independent of the BIOS version or the revision status of the mainboard used. The CPU and BIOS compatibility lists are available on the Internet at www.fujitsu-siemens.de/mainboards. Mainboard: Revision level The revision status of the mainboard exactly identifies which mainboard you have. It is indicated on a sticker on the edge of the mainboard: D1522-B10 GS 1 05618476 Example of revision status of the mainboard D1522-B10 GS 1 BIOS version The BIOS version can be displayed in the BIOS Setup. Ê Ê Press [F2] during booting to open the BIOS Setup. Press [F1]. The BIOS version is specified on the displayed information page under the entry BIOS Release. A26361-D1522-Z120-3-6319 English - 27 Error messages Error messages This chapter contains error messages generated by the mainboard. Available CPUs do not support the same bus frequency ­ System halted! Memory type mixing detected Non Fujitsu Siemens Memory Module detected ­ Warranty void There are more than 32 RDRAM devices in the system Check whether the system configuration has changed. If necessary, correct the settings. BIOS update for installed CPU failed This message appears if the microcode update required for the connected processor is not contained in the system BIOS. Ê Ê Boot the system with the inserted Flash BIOS floppy disk. Abort the normal Flash BIOS update by answering the question about whether you want to perform the update with nÚ To carry out the Flash BIOS update for the processor, enter: flashbioË/p6 Ú Ê Check date and time settings The system date and time are invalid. Set the current date and time in the Main menu of the BIOS Setup. CPU ID 0x failed Switch the server off and on again. If the message is still displayed, go into the BIOS setup and set the corresponding processor to Disabled in the Server - CPU Status menu; please contact your sales outlet or customer service centre. CPU mismatch detected You have replaced the processor or changed the frequency setting. As a result, the characteristic data of the processor have changed. Confirm this change by running the BIOS Setup and exiting it again. Diskette drive A error Diskette drive B error Check the entry for the diskette drive in the Main menu of the BIOS Setup. Check the connections to the diskette drive.