User manual ABIT AN9-32X

Introduction AN9 32X Motherboard AMD Socket AM2 User's Manual Hardware Setup BIOS Setup AMD Socket AM2 ATX Motherboard NB: NVIDIA C51XE SB: NVIDIA MCP55PXE 2GHz HT Dual DDR2 800 DIMM Slots NVIDIA SLI Technology Dual PCI-E X16 Slots Dual GbE LAN IEEE 1394a About this Manual: This user's manual contains all the information you may need for setting up this motherboard. To read the user's manual of PDF format (readable by Adobe Reader), place the "Driver & Utility CD" into the CD-ROM drive in your system. The auto-run screen will appear, click the "Manual" tab to enter its submenu. If not, browse the root directory of the CD-ROM via the File Manager, and double click the "AUTORUN" file. Driver & Utility CD 8x SATA 3Gb/s with RAID ABIT GuruTM Technology ABIT Silent OTESTM Technology 7.1 Channel HD Audio Appendix AN9 32X User's Manual English, 2nd Edition July, 2006 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. This document contains materials protected under International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed without the expressed written permission of the manufacturer and authors of this manual. If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail, we cannot guarantee any responsibility. ii AN9 32X Introduction Contents 1. Introduction ..................................................................... 1-1 1.1 Features & Specifications .............................................................1-1 1.2 Motherboard Layout.....................................................................1-3 Hardware Setup BIOS Setup Driver & Utility CD Appendix 2. Hardware Setup ............................................................... 2-1 2.1 Choosing a Computer Chassis .......................................................2-1 2.2 Installing Motherboard .................................................................2-1 2.3 Checking Jumper Settings ............................................................2-2 2.3.1 CMOS Memory Clearing Header and Backup Battery ..............2-3 2.3.2 Wake-up Headers................................................................2-5 2.4 Connecting Chassis Components...................................................2-6 2.4.1 ATX Power Connectors ........................................................2-6 2.4.2 Front Panel Switches & Indicators Headers............................2-7 2.4.3 FAN Power Connectors ........................................................2-8 2.5 Installing Hardware......................................................................2-9 2.5.1 CPU Socket AM2 .................................................................2-9 2.5.2 DDR2 Memory Slots .......................................................... 2-11 2.5.3 PCI Express X16 Add-on Slots (Install Graphics Card) .......... 2-13 2.5.4 AudioMAX Connection Slot ................................................. 2-15 2.6 Connecting Peripheral Devices .................................................... 2-18 2.6.1 Floppy and IDE Disk Drive Connectors ................................ 2-18 2.6.2 Serial ATA Connectors ....................................................... 2-19 2.6.3 Additional USB 2.0 Port Headers......................................... 2-20 2.6.4 Additional IEEE1394 Port Headers ...................................... 2-20 2.6.5 PCI Express X1 Add-on Slots .............................................. 2-21 2.6.6 PCI Add-on Slot ................................................................ 2-21 2.6.7 GURU Panel Connection Header ......................................... 2-22 2.7 Onboard Status Display .............................................................. 2-23 2.7.1 POST Code Displayer......................................................... 2-23 2.7.2 Power Source Indicators .................................................... 2-24 2.8 Connecting I/O Devices.............................................................. 2-25 3. BIOS Setup....................................................................... 3-1 3.1 µGuruTM Utility..............................................................................3-2 3.1.1 OC Guru .............................................................................3-2 3.1.2 ABIT EQ .............................................................................3-4 3.2 Standard CMOS Features............................................................ 3-11 AN9 32X iii 3.3 Advanced BIOS Features ............................................................ 3-14 3.4 Advanced Chipset Features......................................................... 3-16 3.5 Integrated Peripherals................................................................ 3-18 3.6 Power Management Setup.......................................................... 3-22 3.7 PnP/PCI Configurations .............................................................. 3-25 3.8 Load Fail-Safe Defaults .............................................................. 3-27 3.9 Load Optimized Defaults ............................................................ 3-27 3.10 Set Password........................................................................... 3-27 3.11 Save & Exit Setup .................................................................... 3-27 3.12 Exit Without Saving.................................................................. 3-27 4. Driver & Utility CD............................................................ 4-1 4.1 nVidia nForce Chipset Driver.........................................................4-2 4.2 Realtek HD Audio Driver...............................................................4-3 4.3 Silicon Image 3132 RAID Driver ....................................................4-4 4.4 Cool'n'Quiet Driver .......................................................................4-5 4.5 USB 2.0 Driver.............................................................................4-7 4.6 ABIT µGuru Utility........................................................................4-7 4.7 NVRaid Floppy Disk......................................................................4-8 5. Appendix .......................................................................... 5-1 5.1 POST Code Definitions .................................................................5-1 5.1.1 AWARD POST Code Definitions.............................................5-1 5.1.2 AC2005 POST Code Definitions.............................................5-4 5.2 Troubleshooting (How to Get Technical Support?) ..........................5-5 5.2.1 Q & A .................................................................................5-5 5.2.2 Technical Support Form ......................................................5-8 5.2.3 Universal ABIT Contact Information ......................................5-9 iv AN9 32X Introduction 1. Introduction 1.1 Features & Specifications CPU · Supports Socket 940 AM2 Processor with 2GHz system bus using Hyper-TransportTM Technology · Supports AMD CPU Cool `n' Quiet Technology Chipset · Northbridge: NVIDIA®C51XE Chipset · Southbridge: NVIDIA® MCP55PXE Chipset Memory · Four 240-pin DIMM slots · Supports Dual Channel DDR2 800 Un-buffered ECC/Non-ECC memory · Supports maximum memory capacity up to 8GB ABIT Engineered · ABIT GuruTM Technology · ABIT Silent OTESTM Technology NVIDIA SLI Technology · Two PCI-Express X16 slots support NVIDIA Scalable Link Interface SATA 3Gb/s RAID · Supports 6 ports NV SATA 3Gb/s RAID 0/1/0+1/5/JBOD 2 nd SATA 3Gb/s RAID · 1x Internal SATA 3Gb/s port · 1x External SATA 3Gb/s port Dual GbE LAN · Dual NVIDIA® Gigabit Ethernet IEEE 1394 · Supports 2 Ports IEEE 1394a at 400Mb/s transfer rate Audio · ABIT AudioMAX HD 7.1 CH · Supports auto jack sensing and optical S/PDIF In/Out Expansion Slots · 2x PCI Express x16 slots · 2x PCI Express x1 slots · 1x PCI slot AN9 32X 1-1 · 1x AudioMAX slot Internal I/O Connectors · · · · · · · · · · · 1x 1x 7x 3x 2x Floppy port UDMA 133/100/66/33 connector SATA connectors USB 2.0 headers IEEE1394a headers Rear Panel I/O Silent OTESTM 1x eSATA connector 1x PS/2 Keyboard connector 1x PS/2 Mouse connector 2x RJ-45 Gigabit LAN ports 4x USB 2.0 ports RoHS Compliancy · 100% Lead-free process and RoHS compliancy Miscellaneous · ATX form factor (305mm x 245mm) Specifications and information contained herein are subject to change without notice. 1-2 AN9 32X Introduction 1.2 Motherboard Layout AN9 32X 1-3 1-4 AN9 32X 2. Hardware Setup In this chapter we will elaborate all the information you need upon installing this motherboard to your computer system. Always power off the computer and unplug the AC power cord before adding or removing any peripheral or component. Failing to so may cause severe damage to your motherboard and/or peripherals. Plug in the AC power cord only after you have carefully checked everything. Hardware Setup 2.1 Choosing a Computer Chassis · · This motherboard carries an ATX form factor of 305 x 245 mm. Choose a chassis big enough to install this motherboard. As some features for this motherboard are implemented by cabling connectors on the motherboard to indicators and switches or buttons on the chassis, make sure your chassis supports all the features required. If there is possibility of adopting some more hard drives, make sure your chassis has sufficient power and space for them. Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O shield of the chassis matches the I/O port configuration of this motherboard. You can find an I/O shield specifically designed for this motherboard in its package. · · 2.2 Installing Motherboard Most computer chassis have a base with many mounting holes to allow the motherboard to be securely attached, and at the same time, protected the system from short circuits. There are two ways to attach the motherboard to the chassis base: 1. with studs, 2. or with spacers In principle, the best way to attach the board is with studs. Only if you are unable to do this should you attach the board with spacers. Line up the holes on the board with the mounting holes on the chassis. If the holes line up and there are screw holes, you can attach the board with studs. If the holes line up and there are only slots, you can only attach with spacers. Take the tip of the spacers and insert them into the slots. After doing this to all the slots, you can slide the board into position aligned with slots. After the board has been positioned, check to make sure everything is OK before putting the chassis back on. AN9 32X 2-1 To install this motherboard: 1. Locate all the screw holes on the motherboard and the chassis base. 2. Place all the studs or spacers needed on the chassis base and have them tightened. 3. Face the motherboard's I/O ports toward the chassis's rear panel. 4. Line up all the motherboard's screw holes with those studs or spacers on the chassis. 5. Install the motherboard with screws and have them tightened. To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they are already fastened on the chassis base and are without mounting-holes on the motherboard to align with. 2.3 Checking Jumper Settings For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position. SHORT Face the chassis's rear panel. OPEN OPEN For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in. Pin 1~2 SHORT Pin 2~3 SHORT 2-2 AN9 32X 2.3.1 CMOS Memory Clearing Header and Backup Battery The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu, or (d) whenever there is modification on the CPU or memory modules. This header uses a jumper cap to clear the CMOS memory and have it reconfigured to the default values stored in BIOS. Hardware Setup · · Pins 1 and 2 shorted (default): Normal operation. Pins 2 and 3 shorted: Clear CMOS memory. To clear the CMOS memory and load in the default values: 1. Power off the system and disconnect with AC power source. 2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper cap back to its default settings --- pin 1 and pin 2 shorted. 3. Power on the system. 4. For incorrect CPU ratio/clock settings in the BIOS, press key to enter the BIOS setup menu right after powering on system. 5. Set the CPU operating speed back to its default or an appropriate value. 6. Save and exit the BIOS setup menu. AN9 32X 2-3 CMOS Backup Battery: An onboard battery saves the CMOS memory to keep the BIOS information stays on even after disconnected your system with power source. Nevertheless, this backup battery exhausts after some five years. Once the error message like "CMOS BATTERY HAS FAILED" or "CMOS checksum error" displays on monitor, this backup battery is no longer functional and has to be renewed. To renew the backup battery: 1. Power off the system and disconnect with AC power source. 2. Remove the exhausted battery. 3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The "+" side is its positive polarity. 4. Connect AC power source and power on the system. 5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary. CAUTION: Danger of explosion may arise if the battery is incorrectly renewed. Renew only with the same or equivalent type recommended by the battery manufacturer. Dispose of used batteries according to the battery manufacturer's instructions. 2-4 AN9 32X 2.3.2 Wake-up Headers These headers use a jumper cap to enable/disable the wake-up function. Hardware Setup · PS2-PWR1: Pin 1-2 shorted (Default): Disable wake-up function support at Keyboard/Mouse port. Pin 2-3 shorted: Enable wake-up function support at Keyboard/Mouse port. USB-PWR1: Pin 1-2 shorted (Default): Disable wake-up function support at USB1 port. Pin 2-3 shorted: Enable wake-up function support at USB1 port. USB-PWR2: Pin 1-2 shorted (Default): Disable wake-up function support at USB2 port. Pin 2-3 shorted: Enable wake-up function support at USB2 port FP-PWR1: Pin 1-2 shorted (Default): Disable wake-up function support at FP-USB1 port. Pin 2-3 shorted: Enable wake-up function support at FP-USB1 port. FP-PWR2: Pin 1-2 shorted (Default): Disable wake-up function support at FP-USB2 port. Pin 2-3 shorted: Enable wake-up function support at FP-USB2 port FP-PWR3: Pin 1-2 shorted (Default): Disable wake-up function support at FP-USB3 port. Pin 2-3 shorted: Enable wake-up function support at FP-USB3 port · · · · · AN9 32X 2-5 2.4 Connecting Chassis Components 2.4.1 ATX Power Connectors These connectors provide the connection from an ATX power supply. As the plugs from the power supply fit in only one orientation, find the correct one and push firmly down into these connectors. ATX 24-Pin Power Connector: The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector. Connect from pin-1 for either type. However, a 20-pin power supply may cause the system unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W or higher is recommended. ATX 12V 4-Pin Power Connector: This connector supplies power to CPU. The system will not start without connecting power to this one. Auxiliary 12V Power Connector: This connector provides an auxiliary power source for devices added on PCI Express slots. 2-6 AN9 32X 2.4.2 Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark "+" align to the pin in the figure below stands for positive polarity for the LED connection. Please pay attention when connecting these headers. A wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could cause system malfunction. Hardware Setup · · · · · · HLED (Pin 1, 3): Connects to the HDD LED cable of chassis front panel. RST (Pin 5, 7): Connects to the Reset Switch cable of chassis front panel. SPKR (Pin 13, 15, 17, 19): Connects to the System Speaker cable of chassis. SLED (Pin 2, 4): Connects to the Suspend LED cable (if there is one) of chassis front panel. PWR (Pin 6, 8): Connects to the Power Switch cable of chassis front panel. PLED (Pin 16, 18, 20): Connects to the Power LED cable of chassis front panel. AN9 32X 2-7 2.4.3 FAN Power Connectors These connectors each provide power to the cooling fans installed in your system. · · · CPUFAN1: CPU Fan Power Connector SYSFAN1: System Fan Power Connector AUXFAN1~4: Auxiliary Fan Power Connector These fan connectors are not jumpers. DO NOT place jumper caps on these connectors. 2-8 AN9 32X 2.5 Installing Hardware DO NOT scratch the motherboard when installing hardware. An accidentally scratch of a tiny surface-mount component may seriously damage the motherboard. 2.5.1 CPU Socket AM2 DO NOT touch or bend the delicate pins on the CPU whenever you are holding it. Hardware Setup The installation procedures vary with different types of CPU fan-and-heatsink assembly. The one shown here is served for DEMO only. For detailed information on how to install the one you bought, refer to its installation guidelines. 1. Pull out the socket lever away from the socket and fully lift it up over 90-degree angle. Locate and align the triangle mark with both the CPU and the socket body. Vertically place the CPU with its pin-side down into the socket. Be careful to insert the CPU into the socket. The CPU only fits in one orientation with the socket. DO NOT force the CPU into the socket. 2. After placing the CPU into position, push the socket lever down into its locked position to secure the CPU. The lever clicks when it's locked into position. 3. The heatsink for CPU may have thermal interface material attached to its bottom. If not, applying a few squeeze of thermal paste to the CPU die will help to increase the contact. AN9 32X 2-9 4. Place the heatsink and fan assembly onto the retention frame. Match the heatsink clip with the socket mounting-lug. Hook the spring clip to the mounting-lug. 5. On the other side, push the retention clip straight down to lock into the plastic lug on the retention frame. 6. Connect the CPU cooling fan power cable to the CPUFAN1 connector on this motherboard. The "CPUFAN1" connector can be connected either with a 3-Pin or 4-Pin CPU cooling fan. For a 3-Pin connection, there will be no speed control available in the BIOS setup menu; the CPU fan will run at full speed. Also, please watch out for the orientation when inserting 3-Pin plug into this 4-Pin fan connector. The motherboard in this illustration is served for DEMO only, may not be the same type or model as the one described in this user's manual. A higher fan speed will be helpful for better airflow and heat-dissipation. Nevertheless, stay alert to touch any heatsink since the high temperature generated by the working system is still possible. 2-10 AN9 32X 2.5.2 DDR2 Memory Slots This motherboard provides four 240-pin DIMM slots for Dual Channel DDR2 800 memory modules with memory expansion size up to 8GB. Hardware Setup To reach the performance of Dual Channel DDR2, the following rules must be obeyed: · For a 2-DIMM dual-channel installation: Populate DIMM modules of the same type and size on slots [DIMM1]+[DIMM2], or slots [DIMM3]+[DIMM4]. For a 4-DIMM dual-channel installation: Populate 2 DIMM modules of the same type and size on slots [DIMM1]+[DIMM2], and another 2 DIMM modules of the same type and size on slots [DIMM3]+[DIMM4]. · [DIMM1] and [DIMM2] slots are made of the same color. [DIMM3] and [DIMM4] are made of another same color. Usually there is no hardware or BIOS setup required after adding or removing memory modules, but you will have to clear the CMOS memory first if any memory module related problem occurs. AN9 32X 2-11 To install system memory: 1. Power off the computer and unplug the AC power cord before installing or removing memory modules. 2. Locate the DIMM slot on the board. 3. Hold two edges of the DIMM module carefully, keep away from touching its connectors. 4. Align the notch key on the module with the rib on the slot. 5. Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snap into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fits in one direction. 6. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module. Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly. 2-12 AN9 32X