User manual ACER AC707

English Trademarks VGA & 8514/A are registered trademarks of the IBM Corporation. Super VGA is a registered trademark of VESA. Edition A English CONTENTS FCC warning ..........................................................E-1 DOC notice .............................................................E-1 Safety precautions ..................................................E-1 Packing contents .....................................................E-2 Unpacking procedure ..............................................E-2 Repacking ...............................................................E-2 Introduction ............................................................E-2 Power saving ..........................................................E-2 Install the monitor ...................................................E-3 Power cord ..............................................................E-3 User controls and indicators ...................................E-4 Using the on-screen menu ......................................E-5 Individual adjustment .............................................E-6 Troubleshooting......................................................E-8 Servicing .................................................................E-8 Signal connector information .................................E-8 Technical specifications .........................................E-9 Preset modes .........................................................E-10 English E-1 FEDERAL COMMUNICATIONS COMMISSION (FCC) WARNING nstruction to Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. DOC NOTICE This product conforms to Canadian Class B emissions regulations. Ce produit est conforme aux réglements d'émission Canadienne class B. Power Input Refer to the section about "Connecting the Power Cord". · Do not modify the three-prong grounding type power plug in any way. Installation · Do not place the monitor on an unstable cart, stand, or shelf where it may fall and injure personnel or damage equipment. · Route power cords so that if cannot be walked upon or tripped over. Do not allow anything to rest on the power cord. Do not install the monitor where there is dampness, or where it may be exposed to rain or water. Avoid spilling liquid of any kind on the unit. S AFETY PRECAUTIONS PRECAUTIONS · - This equipment has been certified to comply with the limits for a Class B computing device, pursuant to part 15 of the FCC rules. Only peripherals (computer input / output devices, terminals, printers etc.) certified to comply to the Class B limits may be attached to this computer. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Remarks To meet FCC requirement, shielded cables are required to connect the device to a personal computer or other Class B certified device. Information to Users Any change or modifications expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Ventilation · Do not block or cover ventilation openings on the back or bottom of the monitor cabinet. · Do not place the monitor near a radiator or heating vent. Do not push objects of any kind through cabinet openings. This may result in fire or electric shock. · E-2 PACKING CONTENTS The package contains: · CRT monitor · AC power cord · User manual INTRODUCTION This microprocessor-based, digital control 17" color monitor is a high performance and easy to use product. It employs the latest on-screen-menu technology. The microprocessor capability offers 13 most commonly used VESA timing modes preset in the factory, and 6 modes for user to adjust to the special timings that user might have. We hope that you will find this manual is helpful in obtaining the fullest use of your monitor, and in ensuring your personal safety during operation. UNPACKING PROCEDURE 1 2 POWER SAVING 3 4 The monitor will be driven into "Power Saving" mode by the control signal from the display controller, as indicated by the amber-color power LED. State ON 5 Power Consumption Normal < 5W LED Light Green Amber Active OFF REPACKING Save the origional box and all packing material for future shipping needs. * Packing materials and product are recyclable. The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 10 seconds. English E-3 INSTALL THE MONITOR · To connect the tilt/swivel base to the monitor, align hooks with the sockets on bottom side of the monitor, and gently push the base towards the front of the monitor. The 15-pin D-shell signal connector on the signal cable will connect easily to the video adapter output on your personal computer. Lock both screws on the connector to ensure a firm connection. Turn the PC power switch ON. Then turn the monitor power switch ON, by pressing the switch inward. The green power indicator will light up. Allow about 30 seconds for the CRT tube to warm up. Data will be displayed on the screen. If your display fails to function properly, please first refer to the section "Troubleshooting" in this manual. POWER CORD · Check first to make sure that the power cord you use is the correct type required for your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/ 240V AC voltage area. No user-adjustment is required. First connect the power cord into your monitor's power input socket, and then plug the other end into a 3-pin AC outlet. The power cord may be connected to either a wall socket or the power output socket on your PC, depending on the type of power cord supplied with your monitor. For units to be used at 120V AC: Use a UL Listed Cord Set consisting of a min. No. 18 AWG, Type SVT or SJT three-conductor a maximum of 10 ft. in length and a parallel blade, grounding type attachment plug rated 10A, 125V. For units to be used at 240V AC (domestic use): Use a UL Listed Cord Set consisting of a min. No. 18 AWG, Type SVT or SJT three-conductor cord a maximum of 10 ft. in length and a tandem blade, grounding type attachment plug rated 10A, 250V. For units to be used at 220/240V AC (outside of U.S.): Use a Cord Set consisting of a min. 0.75mm 2,3G,Type H05VV-F cord and grounding type attachment plug rated 16A, 250V. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed and marked HAR. · · · · · · · · · E-4 USER CONTROLS AND INDICATORS a b c 1 2 a. Displays menu & exits menu b. Scrolls through menu to choose an icon for adjustment / Adjusts level of selected icon c. Confirms menu selection 1. Power LED 2. Power ON/OFF switch English E-5 USING THE ON-SCREEN DISPLAY 1) Menu screen-press the 1 button to display the menu below and exit menus Select mark Press the button to move the selection mark to the desired location. Adjustment icons 1: CONTRAST :2 When the 2 button is pressed. The selected adjustment screen appears. The item presently being adjusted is shown. CONTRAST V.SIZE ROTATION DEGAUSS BRIGHTNESS V.POSITION COLOR RECALL H.SIZE V.PINCUSHION LANGUAGE H.MOIRE H.POSITION TRAPEZOID DISP.FREQ V.MOIRE 1: CONTRAST :2 2) Adjustment screen (example: horizontal position adjustment) Name of adjustment screen Adjustment icon H.POSITION 50 1: End Button When the 1 button is pressed, the adjustment level is stored, the adjustment screen is ended and the menu screen returns. / :2 When the 2 button is pressed, the horizontal size adjustment screen appears. On the adjustment screen where these two adjustment icons appear, it is possible to switch between the two screens by pressing the 2 button. The adjustment level is shown by both a number and a bar. It can be varied with the front buttons. NOTE: The amount of adjustment depends upon how long you depress the adjustment button. You may have to tap the button to obtain the desired results. E-6 INDIVIDUAL ADJUSTMENT CONTRAST adjustment Adjust the screen contrast to match your personal perference. Press the button to decrease contrast and press the button to increase it. Direct operation: You can access the CONTRAST adjustment screen by pressing the or before entering the menu screen. Press the 2key toggles between CONTRAST and BRIGHTNESS. BRIGHTNESS adjustment Adjusts the brightness to get the desired background level. Press the button to make the background lighter, the button to make it darker. Press the 2key toggles between CONTRAST and BRIGHTNESS. HORIZONTAL SIZE adjustment Fills the viewable area horizontally. Press the button to make the image narrower, or press the button to make it wider. Press the 2 key toggles between HORIZONTAL SIZE and HORIZONTAL POSITION. HORIZONTAL POSITION adjustment Shifts the image on the screen horizontally. Press the button to move the screen image to the left, or press the button to move it to the right. Press the 2 key toggles between HORIZONTAL SIZE and HORIZONTAL POSITION. VERTICAL SIZE adjustment Fills the viewable area vertically. Press the button to make the image smaller, or press the button to make it larger. Press the 2key toggles between VERTICAL SIZE and VERTICAL POSITION. VERTICAL POSITION adjustment Shifts the image on the screen vertically. Press the button to move it downward, or press the button to move it upward. Press the 2key toggles between VERTICAL SIZE and VERTICAL POSITION PINCUSHION adjustment The image can be corrected for barrel distortion. Press the button or the button to eliminate curved vertical lines. Press the 2 key toggles between PINCUSHION and TRAPEZOID correction. TRAPEZOID adjustment The image can be corrected for the trapezoidal distortion. Press the button to narrow the top edge, or press the button to make the top edge wider. Press the 2 key toggles between PINCUSHION and TRAPEZOID correction. ROTATION adjustment The image can be corrected for tilted picture. Press the button to tilt the image to the left, or press the button to tilt the image to the right. English E-7 COLOR selection The white of the image can be adjusted. 1) Use the button to select: (1)9300 OK, (2)6500 OK or (3)User color. 2) If the (3):the user's color is selected, "2" appears in the lower right of the On-Screen Menu. Press the 2 button to display the USER COLOR adjustment screen. USER COLOR The white of the video image can be adjusted to the user's preferred color. 1) Use the 2 button to select R (red), G (green) or B (blue). 2) Use the button to adjust the color as desired. IMPORTANT-Memory recall of the user's color is not possible, so take note of the initial setting before adjusting. When the monitor is turned OFF, user color keeps the last adjustment. LANGUAGE selection The language of the On-Screen Menu can be selected among English, French, German, Italian and Spanish. Select with the buttons. DISP. FREQ (Input frequency display) This displays the input synchronization signal frequency. It identifies the horizontal and vertical frequency sent to the monitor from the video card currently in use. MANUAL DEGAUSSING After moving the selector to the degauss icon, press the 2 button. The degaussing action takes place a few seconds later. Note: A sharp snap noise may be heard when degaussing occurs. This is normal. MEMORY RECALL It is possible to restore adjustments to the original factory settings. If the monitor is operating in a user defined mode, this control has no effect. HORIZONTAL MOIRE Reduce the dark wavy line Moire pattern on the screen. Press the or button to minimize the horizontal moire image on the screen. VERTICAL MOIRE Reduce the dark wavy line Moire pattern on the screen. Press the or button to minimize the vertical moire image on the screen. E-8 TROUBLESHOOTING If your monitor fails to operate functionally, it may be possible to correct the problem by making simple checks as follows: Problem Blank screen (*NOTE) · Check & Adjust Monitor power switch, power cord, signal cable, or connector PC power switch Brightness & contrast controls Vertical centering & horizontal phase controls Vertical & horizontal size controls Brightness & contrast controls SERVICING Refer all servicing to qualified service personnel. Serious shock hazards exist within the covers of this monitor. Do not open the covers under any circumstances- there are no user serviceable parts inside. · · Display position off-center Display too small or too large Display too bright or too dim · · · SIGNAL CONNECTOR INFORMATION 1 5 Refer to the operation instructions for your computer/ video adapter to ensure that you have the correct signal output source for the monitor. Ensure that the switches on the video adapter are set correctly for operation with this monitor. If the above steps fail to correct the problem contact your dealer for servicing by qualified service personnel. Please remember that the monitor should be returned for servicing together with the power cord. * NOTE: You can easily distinguish if the problem is on the monitor or on the computer by using the monitor's built-in selftest function. With the monitor power ON, disconnect the signal cable from monitor. If you see a "NO SIGNAL" image on the screen, the monitor is functioning properly, and the problem is with the PC side or signal cable. 15 Pin 1 2 3 4 5 6 7 8 Function Red signal Green signal Blue signal Ground *N O T E Red return Green return Blue return Pin 9 10 11 12 13 14 15 Function ** N O T E Digital ground Ground SDA (DDC2B) Horizontal Synchronization Vertical synchronization & V C LK SCL (DDC 2B) This pin is used for self test detection; at PC side, this pin has to be connected to ground. **NOTE: This pin is used for PC99, at PC side, this pin will supply +5VDC. *NOTE: English E-9 TECHNICAL SPECIFICATIONS Screen Size 17" visual diagonal Viewable screen size 15.98" Anti-Glare Coating** Power Input Voltage/ Frequency 100 to 240V AC 50 - 60 Hz Dot Pitch 0.27mm Current Rating 1.5 A Display Area Default Full Scan (H x W) 230 x 306 (mm), typical 245 x 327 (mm), depends on signal timing Infinite 1600 Dots x 1200 Lines All graphic modes with horizontal frequencies between 30 KHz to 86 KHz Power Consumption 75 W (MAX.) Display Colors Max. Resolution Dimension (W x H x D) Weight 404 x 407.4 x 422.6 mm (approximate) 14.5 ± 1 kg Compatibility Operating Temperature 10°C to 35°C Synchronization Horizontal: Vertical: Bandwidth 30 to 86 KHz 50 to 120Hz 135 MHz Video RGB Analog Sync. TTL Separate 15-pin D-sub connector Storage Temperature -40°C to 65°C Humidity 20% to 80% (non-condensing) Up to7000ft Input Signal Altitude TCO (optional) Signal Cable Meet TCO99 * Specifications are subject to change without notice. ** TCO version has a different surface treatment. *** This product is ERGONOMICS APPROVED. E-10 PRESET MODES Mode 1 2 3 4 5 6 7 Resolution (H x V) 720 x 400 640 x 480 800 x 600 640 x 480 800 x 600 1024 x 768 800 x 600 H. Freq. (KHz) 31.4 31.4 37.9 43.3 46.8 48.3 53.6 V. Freq. (Hz) 70 60 60 85 75 60 85 Mode 8 9 10 11 12 13 Resolution (H x V) 1024 x 768 1280 x 1024 1024 x 768 1600 x 1200 1280 x 1024 1280 x 960 H. Freq. (KHz) 60 64.3 68.6 75 80 85.9 V. Freq. (Hz) 75 60 85 60 75 85 English E-1 FEDERAL COMMUNICATIONS COMMISSION (FCC) WARNING nstruction to Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. DOC NOTICE This product conforms to Canadian Class B emissions regulations. Ce produit est conforme aux réglements d'émission Canadienne class B. Power Input Refer to the section about "Connecting the Power Cord". · Do not modify the three-prong grounding type power plug in any way. Installation · Do not place the monitor on an unstable cart, stand, or shelf where it may fall and injure personnel or damage equipment. · Route power cords so that if cannot be walked upon or tripped over. Do not allow anything to rest on the power cord. Do not install the monitor where there is dampness, or where it may be exposed to rain or water. Avoid spilling liquid of any kind on the unit. S AFETY PRECAUTIONS PRECAUTIONS · - This equipment has been certified to comply with the limits for a Class B computing device, pursuant to part 15 of the FCC rules. Only peripherals (computer input / output devices, terminals, printers etc.) certified to comply to the Class B limits may be attached to this computer. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Remarks To meet FCC requirement, shielded cables are required to connect the device to a personal computer or other Class B certified device. Information to Users Any change or modifications expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Ventilation · Do not block or cover ventilation openings on the back or bottom of the monitor cabinet. · Do not place the monitor near a radiator or heating vent. Do not push objects of any kind through cabinet openings. This may result in fire or electric shock. · E-2 PACKING CONTENTS The package contains: · CRT monitor · AC power cord · User manual INTRODUCTION This microprocessor-based, digital control 17" color monitor is a high performance and easy to use product. It employs the latest on-screen-menu technology. The microprocessor capability offers 13 most commonly used VESA timing modes preset in the factory, and 6 modes for user to adjust to the special timings that user might have. We hope that you will find this manual is helpful in obtaining the fullest use of your monitor, and in ensuring your personal safety during operation. UNPACKING PROCEDURE 1 2 POWER SAVING 3 4 The monitor will be driven into "Power Saving" mode by the control signal from the display controller, as indicated by the amber-color power LED. State ON 5 Power Consumption Normal < 5W LED Light Green Amber Active OFF REPACKING Save the origional box and all packing material for future shipping needs. * Packing materials and product are recyclable. The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 10 seconds. English E-3 INSTALL THE MONITOR · To connect the tilt/swivel base to the monitor, align hooks with the sockets on bottom side of the monitor, and gently push the base towards the front of the monitor. The 15-pin D-shell signal connector on the signal cable will connect easily to the video adapter output on your personal computer. Lock both screws on the connector to ensure a firm connection. Turn the PC power switch ON. Then turn the monitor power switch ON, by pressing the switch inward. The green power indicator will light up. Allow about 30 seconds for the CRT tube to warm up. Data will be displayed on the screen. If your display fails to function properly, please first refer to the section "Troubleshooting" in this manual. POWER CORD · Check first to make sure that the power cord you use is the correct type required for your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/ 240V AC voltage area. No user-adjustment is required. First connect the power cord into your monitor's power input socket, and then plug the other end into a 3-pin AC outlet. The power cord may be connected to either a wall socket or the power output socket on your PC, depending on the type of power cord supplied with your monitor. For units to be used at 120V AC: Use a UL Listed Cord Set consisting of a min. No. 18 AWG, Type SVT or SJT three-conductor a maximum of 10 ft. in length and a parallel blade, grounding type attachment plug rated 10A, 125V. For units to be used at 240V AC (domestic use): Use a UL Listed Cord Set consisting of a min. No. 18 AWG, Type SVT or SJT three-conductor cord a maximum of 10 ft. in length and a tandem blade, grounding type attachment plug rated 10A, 250V. For units to be used at 220/240V AC (outside of U.S.): Use a Cord Set consisting of a min. 0.75mm 2,3G,Type H05VV-F cord and grounding type attachment plug rated 16A, 250V. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed and marked HAR. · · · · · · · · · E-4 USER CONTROLS AND INDICATORS a b c 1 2 a. Displays menu & exits menu b. Scrolls through menu to choose an icon for adjustment / Adjusts level of selected icon c. Confirms menu selection 1. Power LED 2. Power ON/OFF switch English E-5 USING THE ON-SCREEN DISPLAY 1) Menu screen-press the 1 button to display the menu below and exit menus Select mark Press the button to move the selection mark to the desired location. Adjustment icons 1: CONTRAST :2 When the 2 button is pressed. The selected adjustment screen appears. The item presently being adjusted is shown. CONTRAST V.SIZE ROTATION DEGAUSS BRIGHTNESS V.POSITION COLOR RECALL H.SIZE V.PINCUSHION LANGUAGE H.MOIRE H.POSITION TRAPEZOID DISP.FREQ V.MOIRE 1: CONTRAST :2 2) Adjustment screen (example: horizontal position adjustment) Name of adjustment screen Adjustment icon H.POSITION 50 1: End Button When the 1 button is pressed, the adjustment level is stored, the adjustment screen is ended and the menu screen returns. / :2 When the 2 button is pressed, the horizontal size adjustment screen appears. On the adjustment screen where these two adjustment icons appear, it is possible to switch between the two screens by pressing the 2 button. The adjustment level is shown by both a number and a bar. It can be varied with the front buttons. NOTE: The amount of adjustment depends upon how long you depress the adjustment button. You may have to tap the button to obtain the desired results. E-6 INDIVIDUAL ADJUSTMENT CONTRAST adjustment Adjust the screen contrast to match your personal perference. Press the button to decrease contrast and press the button to increase it. Direct operation: You can access the CONTRAST adjustment screen by pressing the or before entering the menu screen. Press the 2key toggles between CONTRAST and BRIGHTNESS. BRIGHTNESS adjustment Adjusts the brightness to get the desired background level. Press the button to make the background lighter, the button to make it darker. Press the 2key toggles between CONTRAST and BRIGHTNESS. HORIZONTAL SIZE adjustment Fills the viewable area horizontally. Press the button to make the image narrower, or press the button to make it wider. Press the 2 key toggles between HORIZONTAL SIZE and HORIZONTAL POSITION. HORIZONTAL POSITION adjustment Shifts the image on the screen horizontally. Press the button to move the screen image to the left, or press the button to move it to the right. Press the 2 key toggles between HORIZONTAL SIZE and HORIZONTAL POSITION. VERTICAL SIZE adjustment Fills the viewable area vertically. Press the button to make the image smaller, or press the button to make it larger. Press the 2key toggles between VERTICAL SIZE and VERTICAL POSITION. VERTICAL POSITION adjustment Shifts the image on the screen vertically. Press the button to move it downward, or press the button to move it upward. Press the 2key toggles between VERTICAL SIZE and VERTICAL POSITION PINCUSHION adjustment The image can be corrected for barrel distortion. Press the button or the button to eliminate curved vertical lines. Press the 2 key toggles between PINCUSHION and TRAPEZOID correction. TRAPEZOID adjustment The image can be corrected for the trapezoidal distortion. Press the button to narrow the top edge, or press the button to make the top edge wider. Press the 2 key toggles between PINCUSHION and TRAPEZOID correction. ROTATION adjustment The image can be corrected for tilted picture. Press the button to tilt the image to the left, or press the button to tilt the image to the right. English E-7 COLOR selection The white of the image can be adjusted. 1) Use the button to select: (1)9300 OK, (2)6500 OK or (3)User color. 2) If the (3):the user's color is selected, "2" appears in the lower right of the On-Screen Menu. Press the 2 button to display the USER COLOR adjustment screen. USER COLOR The white of the video image can be adjusted to the user's preferred color. 1) Use the 2 button to select R (red), G (green) or B (blue). 2) Use the button to adjust the color as desired. IMPORTANT-Memory recall of the user's color is not possible, so take note of the initial setting before adjusting. When the monitor is turned OFF, user color keeps the last adjustment. LANGUAGE selection The language of the On-Screen Menu can be selected among English, French, German, Italian and Spanish. Select with the buttons. DISP. FREQ (Input frequency display) This displays the input synchronization signal frequency. It identifies the horizontal and vertical frequency sent to the monitor from the video card currently in use. MANUAL DEGAUSSING After moving the selector to the degauss icon, press the 2 button. The degaussing action takes place a few seconds later. Note: A sharp snap noise may be heard when degaussing occurs. This is normal. MEMORY RECALL It is possible to restore adjustments to the original factory settings. If the monitor is operating in a user defined mode, this control has no effect. HORIZONTAL MOIRE Reduce the dark wavy line Moire pattern on the screen. Press the or button to minimize the horizontal moire image on the screen. VERTICAL MOIRE Reduce the dark wavy line Moire pattern on the screen. Press the or button to minimize the vertical moire image on the screen. E-8 TROUBLESHOOTING If your monitor fails to operate functionally, it may be possible to correct the problem by making simple checks as follows: Problem Blank screen (*NOTE) · Check & Adjust Monitor power switch, power cord, signal cable, or connector PC power switch Brightness & contrast controls Vertical centering & horizontal phase controls Vertical & horizontal size controls Brightness & contrast controls SERVICING Refer all servicing to qualified service personnel. Serious shock hazards exist within the covers of this monitor. Do not open the covers under any circumstances- there are no user serviceable parts inside. · · Display position off-center Display too small or too large Display too bright or too dim · · · SIGNAL CONNECTOR INFORMATION 1 5 Refer to the operation instructions for your computer/ video adapter to ensure that you have the correct signal output source for the monitor. Ensure that the switches on the video adapter are set correctly for operation with this monitor. If the above steps fail to correct the problem contact your dealer for servicing by qualified service personnel. Please remember that the monitor should be returned for servicing together with the power cord. * NOTE: You can easily distinguish if the problem is on the monitor or on the computer by using the monitor's built-in selftest function. With the monitor power ON, disconnect the signal cable from monitor. If you see a "NO SIGNAL" image on the screen, the monitor is functioning properly, and the problem is with the PC side or signal cable. 15 Pin 1 2 3 4 5 6 7 8 Function Red signal Green signal Blue signal Ground *N O T E Red return Green return Blue return Pin 9 10 11 12 13 14 15 Function ** N O T E Digital ground Ground SDA (DDC2B) Horizontal Synchronization Vertical synchronization & V C LK SCL (DDC 2B) This pin is used for self test detection; at PC side, this pin has to be connected to ground. **NOTE: This pin is used for PC99, at PC side, this pin will supply +5VDC. *NOTE: English E-9 TECHNICAL SPECIFICATIONS Screen Size 17" visual diagonal Viewable screen size 15.98" Anti-Glare Coating** Power Input Voltage/ Frequency 100 to 240V AC 50 - 60 Hz Dot Pitch 0.27mm Current Rating 1.5 A Display Area Default Full Scan (H x W) 230 x 306 (mm), typical 245 x 327 (mm), depends on signal timing Infinite 1600 Dots x 1200 Lines All graphic modes with horizontal frequencies between 30 KHz to 86 KHz Power Consumption 75 W (MAX.) Display Colors Max. Resolution Dimension (W x H x D) Weight 404 x 407.4 x 422.6 mm (approximate) 14.5 ± 1 kg Compatibility Operating Temperature 10°C to 35°C Synchronization Horizontal: Vertical: Bandwidth 30 to 86 KHz 50 to 120Hz 135 MHz Video RGB Analog Sync. TTL Separate 15-pin D-sub connector Storage Temperature -40°C to 65°C Humidity 20% to 80% (non-condensing) Up to7000ft Input Signal Altitude TCO (optional) Signal Cable Meet TCO99 * Specifications are subject to change without notice. ** TCO version has a different surface treatment. *** This product is ERGONOMICS APPROVED. E-10 PRESET MODES Mode 1 2 3 4 5 6 7 Resolution (H x V) 720 x 400 640 x 480 800 x 600 640 x 480 800 x 600 1024 x 768 800 x 600 H. Freq. (KHz) 31.4 31.4 37.9 43.3 46.8 48.3 53.6 V. Freq. (Hz) 70 60 60 85 75 60 85 Mode 8 9 10 11 12 13 Resolution (H x V) 1024 x 768 1280 x 1024 1024 x 768 1600 x 1200 1280 x 1024 1280 x 960 H. Freq. (KHz) 60 64.3 68.6 75 80 85.9 V. Freq. (Hz) 75 60 85 60 75 85