Table of Contents Preface ........................................................................................................ 2 Chapter 1 Installation................................................................................ 4 Unpacking .....................................................................................................................................4 Connecting the LCD Monitor and Base...................................................................................4 Viewing Angle Adjustment ........................................................................................................4 Detaching LCD Monitor from Its Stand....................................................................................5 Interface for Arm Applications ..................................................................................................5 Connecting the Display to your Computer..............................................................................5 Connecting the AC Power..........................................................................................................7 Setting Up the LCD Monitor......................................................................................................7 Power Management System.......................................................................................................7 Chapter 2 Display Controls....................................................................... 8 User Controls ................................................................................................................................8 Adjusting the Monitor's Display...............................................................................................8 Function Description.................................................................................................................10 Chapter 3 Technical Information ........................................................... 12 Specifications..............................................................................................................................12 Standard Timing Table ..............................................................................................................15 Troubleshooting.........................................................................................................................17 Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. FCC Statement Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturers may void the user's authority to operate this equipment. NOTE A shielded-type signal cord is required in order to meet the FCC emission limits and also to prevent interference to the radio and television reception. It is essential that only the supplied signal cord be used. Canadian DOC Notice 2 This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B repecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can severely damage it. 3. Do not apply pressure to the LCD screen. Excess pressure may cause permanent damage to the display. 4. Do not remove the cover or attempt to service this unit by yourself. Servicing of any nature should be performed by an authorized technician. 5. Store LCD Monitor in a room with a room temperature of -20° ~ 60°C (or -4° ~ 140°F). Storing the LCD Monitor outside this range could result in permanent damage. 6. If any of the following occurs, immediately unplug your monitor and call an authorized technician. * * * Monitor to PC signal cable is frayed or damaged. Liquid spilled into LCD Monitor or the monitor has been exposed to rain. LCD Monitor or the case is damaged. 7. A certified line is required to connect this device to a power outlet. For a nominal current up to 6A and a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0.75 mm2 must be used. 8. For use only with power supply type: Li-shin, LSE 9802A1240 3 ENGLISH Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * AC Adapter * 1.5M Monitor-to-PC signal Cable * 1.8M Power Cord * User's Manual * Base If you find that any of these items is missing or appears damaged, contact your dealer immediately. Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first. Then connect the LCD Monitor and base please.(See fig.1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted from -5°t o +35°. (See fig. 1-2) Figure 1-2 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. 4 Detaching LCD Monitor from Its Stand 1. Unscrew screws of the hinge bracket 2. Remove the stand from LCD monitor (See fig. 1-3) Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13 November 1997). Figure 1-4 Connecting the Display to your Computer 1. Power off your computer. 2. Connect one end of the signal cable to the LCD Monitor's VGA port. (See Fig. 1-5) 3. Connect the other end of the signal cable to the VGA port on your PC. 4. Make sure both connections are secure. Figure 1-5 Attention This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is 5 ENGLISH used. 6 Connecting the AC Power 1. Connect the power cord to the AC adapter. (See Fig. 1-6) 2. Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. 3. Connect the power cord to an AC power source. Figure 1-6 Warning We recommand to install a "Surge Protector" device between the AC Adapter and the electrical wall outlet for adding protection against power surges to prevent the effects of sudden voltage variations from reaching the LCD Monitor. Sudden power surges may damage your monitor. Setting Up the LCD Monitor 1. Make sure the AC Adapter is connected to the LCD Monitor. 2. Turn on the LCD Monitor's power switch, located on the bezel of the monitor. Power Management System This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. signal. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light yellow. 7 ENGLISH Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 1 2 DC Power Switch DC Power-On Indicator Function Select Buttons Adjustment Control Buttons Press the power switch to switch the monitor ON/OFF. LED lights Green color --- Power is ON. LED lights Yellow --- Monitor is in "Power Saving Mode". LED is off --- Power is OFF. Press either left or right control button for OSD (On Screen Display) menu selection. Press the left button to decrease the OSD setting and press the right button to increase the OSD setting. 3 4 Adjusting the Monitor's Display The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. OSD Function Menu To access OSD Main menu, simply press one of the Function Select control buttons, and the menu diagram will pop up on the screen as shown on Fig. 2-2: Continue pressing the Function Select buttons to scroll through the entire menu items ,then press Adjustment Control buttons to adjust content of selected item. Figure 2-2 Attention Firmware revision may have been updated into a latest version while the version number shown on 8 all OSD menus in this manual will stay as Ver. 1.00. 9 ENGLISH Function Description Icon Function Brightness Contrast H-Position V-Position Phase Function Description This function increases or decreases the brightness of the image . This function increases or decreases the difference between the dark and light color. This function shifts the entire display image left or right. This function shifts the entire display image up or down. A total of 32 scales (0 to 31) are available to adjust the focus and clarity of the display. This function carries a frequency tracking feature that offers the user to have better stability and clarity. Increasing Clock value can be up to +50 scales. The number of decreasing Clock (minus) is depend on the input timing. This function will adjust the display size automatically to fit full screen. This function moves the OSD menu window left or right. This function moves the OSD menu window up or down. This function is to choose a display that allows maximum graphics text quality. The resolution selection can either be 640 x 400 or 720 x 400. Please refer to Chapter 3 " Standard Timing" Table for of different timing modes. The recall function will return all adjusted parameters to factory preset values. Five OSD language options are available: English, German, French, Spanish and Italian. Press the left or right Adjustment Control button to select other language. Hue:100 scales of hue are available to adjust hue from green to red. Saturation:100 scales of saturation are available to choose from 0 to 100. Color Temp.: Push the (+ -) button to select a different color temperature. Please see the diagram below for function and description. Saves the values of this setting and exits the OSD menu function. Clock Auto Adjustment OSD H-Position OSD V-Position Graph Text Recall Language Color management Save Exit Icon 9300 6500 Function CIE coordinated Color Temperature of 9300°K CIE coordinated Color Temperature of 6500°K Description Sets the CIE coordinate color temperature to 9300°K Sets the CIE coordinate color temperature to 6500°K 10 User Three colors (Red, Green, Blue) can be adjusted from the OSD menu Sets the settings to a by user defined CIE Temperature. 11 ENGLISH Chapter 3 Te ...