CONTENT F.C.C Statement Important safeguards Chapter 1 Introduction 1.1 Features ................................................................. 1 1.2 Checking List ........................................................... 1 Chapter 2 Chapter 3 Installation Over view of your monitor 2.1 Connect your monitor to computer ................................. 2 3.1 Front Panel over view .................................................. 3 3.2 Rear Panel over view ....................................................3 Chapter 4 Operation 4.1 Power (ON/OFF) switch .............................................. 4 4.2 Power indicator ..........................................................4 4.3 Auto ...................................................................... 4 4.4 Volume ................................................................... 4 4.5 Menu features ........................................................... 4 4.6 OSD menu ............................................................... 5 4.7 Self test pattern ........................................................ 11 4.8 Safety protection ....................................................... 11 4.9 Preset modes timing chart ............................................12 Chapter 5 Technical information 5.1 Products Specifications ................................................13 5.2 Signal Connector Pin Assignment ................................... 14 5.3 Troubleshooting ....................................................... 16 FEDERAL COMMUNICATIONS COMMISSION(F.C.C) STATEMENT This equipment has been tested and found to comply with the limits of a Class B digital device. Pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : 1. Reorient/Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4.Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. IMPORTANT SAFEGUARDS Warnings : 1. Read all of these instructions. 2. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Do not use this monitor near water. For example near a bathtub, washbowl , kitchen sink, or laundry tub, in a wet basement , or near a swimming pool, etc... 4. Do not place this monitor on an unstable cart, stand, or table. The monitor may fall, causing serious injury to a child or audit, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer or sold with monitor. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer. 5. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation of the television receiver and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the monitor on a bed, sofa, rug, or other similar surface. This monitor should not be placed in built-in installation such as a bookcase unless proper ventilation is provided. 6. Do not allow anything to rest on the power cord. Do not locate this monitor where the cord will be abused by persons working on it. 7. Never push objects of any kind into this monitor through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fore or electric shock. Never spill liquid of any kind on the monitor. 8. Do not attempt to service this monitor yourself since opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 9. Unplug this monitor from the wall outlet and refer servicing to qualified service personnel under the following : a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the monitor. c. If the monitor has been exposed to rain or water. d. If the monitor has been dropped or the cabinet has been damaged. e. When the monitor exhibits a distinct change in performance this indicated a need for service. Introduction Chapter 1 Introduction 1.1 Features Multi-scanning at horizontal frequencies of 30KHz to 80KHz and vertical frequencies of 56Hz to 75Hz. Microprocessor based with OSD (On Screen Display) control. Compatible with standard IBM VGA, extended VGA, super VGA, IBM XGA modes, as well as VESA resolution standards. Universal power supply. TCO 99 compliant. Microsoft Windows 9x/2000/XP compatible & VESA Display Data Channel (DDC) 1/2B compatible. 1.2 Checking List Please make sure the following items are included with your LCD monitor. Your monitor AC Adapter AC power cord Signal cable Audio cable If any of these items are missing, please contact with your dealer for technical support and custom service. Note: Be sure to save original box and all packing material for transport in future if the monitor need, 1 Chapter 2 Installation nstallation 2 Over view of your monitor Chapter 3 Over view of your monitor 3.1 Front panel over view 3.2 Rear panel over view 1 3 5 2 6 4 3 Chapter 4 OPERATION Direct ­ Access Features OPERATION Direct ­ Access Features 4 OPERATION Direct ­ Access Features 4.6 OSD menu Main menu OSD main menu of controls gives you an overview of the selection of controls available. When you want to make adjustment of the screen image, press and release button Menu Analog RGB / Digital RGB picture 1. auto adjust A Press > button, auto adjust the display mode to its utmost performance according to VGA setting. 2. brightness Adjust the overall image and background screen brightness. 3. contrast Adjust the image brightness in relation to the background. 4. h position To move the picture image horizontally left or right. 5. v position To move the picture image vertically up or down. 6. phase To improve focus clarity an image stability. 7. clock To increase or decrease the horizontal size of image. 8. exit To exit the menu. 5 OPERATION Direct ­ Access Features advanced 1. sharpness Adjusts the picture sharpness. 2. color You have 4 kinds of options. cool This control adjusts the color temperature of the screen image, this item are preset by factory, you can not adjust these setting. The performance is bluer and brighter. natural This performance is reddish and closer to paper white. warm The performance is yellowish and closer to paper white user You can adjust the individual color intensity by yourself. Increase or decrease red, green or blue depending upon which is selected. user red Increase or decrease red. user green Increase or decrease green. user blue Increase or decrease blue. exit To exit the main menu. audio 1. volume This features adjusts < to decrease volume and > to increase volume. 2. base This features adjusts < to decrease base and > to increase base. 3. treble This features adjusts < to decrease treble and > to increase treble. 4. ATTL This features adjusts < to decrease left speaker volume and > to increase left speaker volume. 6 OPERATION Direct ­ Access Featur es 5. ATTR This features adjusts < to decrease right speaker volume and > to increase right speaker volume. 6. loudness This features choose on or off to get loudness. 7. mute This features choose on or off to mute the sound. 8. exit To exit the main menu. options 1. osd To move the OSD image. 2. osd h position To move the OSD image horizontally left or right. 3. osd v position To move the OSD image vertically up or down. 4. language You can choose one of the nine languages you need. 5. exit To exit the main menu. utilities 1. osd timeout You can select how long the monitor waits after the last adjust of the key to shut off the OSD menu. The time setting choices are from 5 to 60 seconds. 2. osd background You can select opaque or translucent to change OSD background. 3. source icon You can select on or off to display OSD icon. 4. exit To exit the main menu. 7 OPERATION Direct ­ Access Features reset 1. memory recall Reset the currently highlight control to the factory setting. User must be using factory preset video mode to use this function. 2. exit To exit the main menu. exit To exit the OSD menu. Composite Video / S-Video picture 1. brightness Adjust the overall image and background screen brightness. 2. contrast Adjust the image brightness in relation to the background. 3. saturation Adjusts the color saturation of the screen image. 4. hue Adjusts the color hue of the screen image. 5. sharpness Adjusts the picture sharpness. 6. scaling Adjusts the picture size full screen or 16:9 screen. 7. exit To exit the main menu. advanced 1. sharpness Adjusts the picture sharpness. 2. color You have 4 kinds of options. 8 OPERATION Direct ­ Access Features cool This control adjusts the color temperature of the screen image, this item are preset by factory, you can not adjust these setting. The performance is bluer and brighter. natural This performance is reddish and closer to paper white. warm The performance is yellowish and closer to paper white user You can adjust the individual color intensity by yourself. Increase or decrease red, green or blue depending upon which is selected. user red Increase or decrease red. user green Increase or decrease green. user blue Increase or decrease blue. exit To exit the main menu. audio 1. volume This features adjusts < to decrease volume and > to increase volume. 2. base This features adjusts < to decrease base and > to increase base. 3. treble This features adjusts < to decrease treble and > to increase treble. 4. ATTL This features adjusts < to decrease left speaker volume and > to increase left speaker volume. 5. ATTR This features adjusts < to decrease right speaker volume and > to increase right speaker volume. 9 OPERATION Direct ­ Access Features 6. loudness This features choose on or off to get loudness. 7. mute This features choose on or off to mute the sound. 8. exit To exit the main menu. options 1. osd To move the OSD image. 2. OSD h position To move the OSD image horizontally left or right. 3. OSD v position To move the OSD image vertically up or down. 4. language You can choose one of the nine languages you need. 5. exit To exit the main menu. utilities 1. osd timeout You can select how long the monitor waits after the last adjust of the key to shut off the OSD menu. The time setting choices are from OFF to 60 seconds. 2. osd background You can select opaque or translucent to change OSD background. 3. source icon You can select on or off to display OSD icon. 4. exit To exit the main menu. reset 1. memory recall Reset the currently highlight control to the factory setting. User must be using factory preset video mode to use this function. 10 OPERATION Direct ­ Access Features 2. exit To exit the main menu. exit To exit the OSD menu. 4.7 Self test pattern When the computer's video signal is not reaching the monitor, the monitor will display a self test pattern. 4.8 Safety protection When frequency of video signal from computer's was out of range, the monitor will protect by itself and a warning message of OSD will appear on the screen. 11 OPERATION Direct ­ Access Features 4.9 Preset Modes Timing Chart Resolution 720 × 400 640 × 480 640 × 480 640 × 480 800 × 600 800 × 600 800 × 600 1024 × 768 1024 × 768 1024 × 768 1280 × 1024 Horizontal 31.47 kHz 31.47 kHz 37.86 kHz 37.5 kHz 37.88 kHz 48.08 kHz 46.87 kHz 48.36 kHz 56.48 kHz 60.02 kHz 63.98 kHz Vertical 70 Hz 60 Hz 72.8 Hz 75 Hz 60.3 Hz 72.2 Hz 75 Hz 60 Hz 70.1 Hz 75 Hz 60.02 Hz 12 OPERATION Direct ­ AccessFeatur es Chaper 5 t Technical Information 5.1 Pr ducts Specifications o Recommend Resolution Horizontal Freq. Vertical Freq. Active Display Area Dot pitch Display Color Contrast Ratio (Typical) Luminance of white Bandwidth User Control OSD Functions 1024*768@60 Hz 30-80 KHz 56-75 Hz 337*270 mm 0,264*0,264 mm 16,7 M 400 250 cd/m² 135 MHz 4 Key Sw Brightness, contrast, H-position, V-position, H-Size, phase, Color, auto, Reset, language, OSD, Exit, Horizontal Vert ...