User manual ACT ACTPRO200 - INSTALLATION

ACTpro200 Installation 2 Door Controller and Monitored Power Supply WARNING: MAINS VOLTAGE DISCONNECT BEFORE MAINTENANCE LED Functionality: Red LED indicates the status of communications with the controller. While online to the controller the Red LED will flash rapidly. If there is a problem it will flash slowly (about once a second). Green LED will flash if an event occurs on the ACTpro200. Secondary AC Fuse GREEN CLOCK SENSE ACT 2000 NETWORK A B 0V A B 0V A B Shield DOORS DOOR 1 Connections Total Length max 1.4km Belden 9502 or equiv. NO C NC NO C NC 0V TAMPER +5V AC AC DATA +12V RED 5A 250VAC 5A 30VDC OP3 OP2 0V AUX INPUT DC2 PB2 A B 5A 250VAC 5A 30VDC Mains Present Fuse OP2 Blown Fuse OP1 Blown 5A 250VAC 5A 30VDC 5A 250VAC 5A 30VDC 0V DOORS NETWORK Fuse OP1 Fuse OP2 Press to connect batteries 5A 250VAC 5A 30VDC OP3 OP2 0V AUX INPUT DC2 PB2 DOOR 2 Connections 5A 250VAC 5A 30VDC 12345678 BATTERY 1 BATTERY 2 On DATA OUTPUT 1 OUTPUT 2 Entry/Exit Reader Battery OK LEDs Cable: 8 Core Screened Belden 9504 or equiv Entry Reader Battery 1 - Backup for Output 1 and PCB *Always connect Battery 1. Important! Do not reverse battery leads. red lead connects to + terminal of battery black lead connects to - terminal of battery. Door Address 4 5 6 7 8 +12V RED 12V 0V +5V 12V 0V NC C NO NC C NO GREEN CLOCK SENSE 0V Max length: 30m from +5V 100m from +12V Battery 2 - Backup for Output 2 Monitoring for battery 2 can be disabled by setting dipswitch 3 to ON Important ! Always Place Varistor Across Lock Terminals 03 OFF OFF OFF ON 04 OFF OFF ON 05 OFF OFF ON 06 OFF OFF ON 07 OFF OFF ON 08 OFF ON 09 OFF ON 10 OFF ON 11 OFF ON 12 OFF ON 13 OFF ON 14 OFF ON 15 OFF ON 16 ON ON FACTORY DEFAULT This unit should be reset to its factory default condition before installation. To do this, power the unit up with ALL switches in the OFF position. The two LED's will illuminate for about 2 sec. The correct switch settings may then be set. OFF OFF OFF ON ON ON OFF ON This illustration shows wiring for a normally energised lock. If a normally de-energised lock is required, use the N/O relay contacts. Technical Specifications Mains Voltage Frequency Mains Fuse Secondary AC Fuse Fuse OP1 Fuse OP2 Ripple Voltage 230Vac +10% -15% 47-63 Hz 630mAmp 3.15Amps 1.25 Amps Quick 1.25 Amps Quick <200mV White Green Blue Red Black Brown Yellow Orange SENSE CLOCK / DATA 1 DATA / DATA 0 +5V or +12V 0V RED GREEN (Buzzer Control) OFF OFF OFF OFF OFF ON OFF ON OFF ON ON ON ON ON OFF ON For Clock and Data Readers, wire exit reader in parallel but do not connect to SENSE. For Wiegand Readers, wire DATA0 of the exit reader to SENSE. OFF OFF OFF ON ON ON OFF ON OFF OFF OFF OFF Example: When the dipswitch is set to 3, Door 1 is set to Address 3 and Door 2 is set to Address 4. When the dipswitch is set to 4, Door 1 is set to Address 4 and Door 2 is set to Address 5. ACTWinPro users must tick Mains Fault Reporting in the door view www.accesscontrol.ie Access Control Technology, Ireland. Tel: + 353 466 2570