access control TECHNOLOGY Operating & Installation Instructions for ACTSmart 2 Product Range ACTSmart2 Operating and Installation Manual Rev. 1.1 Contents Installation Notes............................................................. ......................................................................4 Product Specification ....................................................... ......................................................................4 30 Second Programming Guide (1080) ................................... ..............................................................5 30 Second Programming Guide (1090) ................................ ................................................................6 Programming Summary................................... ......................................................................................7 ACTSmart Operation ..............................................................................................................................8 ACTSmart Programming...................................... ..................................................................................8 Adding a Card Batch........................... ... ...........................................................................9 Deleting a Card Batch................................................ ..........................................................9 Adding a Pin.........................................................................................................................9 Deleting a Pin................................................... ....................................................................9 Adding a Card and Pin ........................................ ................................................................9 Deleting a Card and Pin. ......................................................................................................9 Adding a Card Batch using the keypad..............................................................................10 Deleting a Card and Pin using the keypad............... ..........................................................10 Adding a Random Card............................... ......................................................................10 Set Door RelayTime..................................... ......................................................................10 Set Door Ajar Time...................................... ......................................................................10 Set Guest Buzzer Time ......................................................................................................10 Change Programming Code........................... ....................................................................11 Change Number of PIN Digits...........................................................................................11 Limit Number of Users.................... ..................................................................................11 User Toggle ........................................................................................................................11 User Arm.................................................. ..........................................................................12 Programming ACTSmart Options.................. ....................................................................13 Setting Programmable Input Function ..............................................................................14 Setting AUX I/O 1 Function ........... ..................................................................................14 Setting AUX I/O 2 Function ..............................................................................................14 Quick I/O Setup ................................................................................................................15 Adding a Card Batch for second door................... ..........................................................15 Adding a PIN for second door ..........................................................................................16 Adding a Card and PIN for second door ..........................................................................16 Adding random Card for second door...............................................................................16 Programming a Network System ..........................................................................................................17 Assign Door Numbers ......................................................................................................17 Find Door Number ............................................................................................................18 Find All Door Numbers......................................................................................................18 Restoring Factory Default ....................................................................................................................18 Programming ACTSmart Prox only......................................................................................................19 ACTSmart Standalone wiring diagram ................................................................................................21 ACTSmart Interlock and Fire Override wiring diagram ......................................................................22 ACTSmart Network wiring diagram ....................................................................................................23 SmartLock Connection diagram ..........................................................................................................24 Alarm Wiring Diagram ........................................................................................................................25 ACTPro Reader Wiring Diagram..........................................................................................................26 2 Door Wiring Diagram ........................................................................................................................26 2 Door Wiring Diagram ........................................................................................................................27 ACTSmart System Diagram ................................................................................................................28 ACTSmart Flush mounting diagram ....................................................................................................29 ACTSmart Surface mount diagram ......................................................................................................30 User List 31 3 ACTSmart2 Operating and Installation Manual Rev. 1.1 Installation Notes · Remember to Factory Default the ACTSmart before programming · Remember to place the supplied varistor across the terminals of the door strike coil to protect the relay contacts · Don't mount the ACTSmart Prox units near RF sources (Eg mobile phones, radio transmitters, computer monitors) or metal surfaces. · Remember that the ACTSmart PIN and Prox units default to Card operation. Card and PIN operation must be programmed in. (See Programming ACTSmart Options section, Options 39, 40 and 41). · Don't power the unit from a switch-mode power supply. Use a linear regulated power supply. · Never use the on-board relay to switch AC mains voltage. An external relay, electrically isolated from the ACTSmart should be used for this purpose · Remember to change the programming code. · Don't power the ACTSmart from an AC power supply on a networked system. An AC power supply may only be used on a standalone ACTSmart. · The ACTSmart2 version is not compatible with the earlier version of ACTSmart. Cards and fobs for one version will not work on the other. The devices may NOT be networked together. · When ordering new cards or fobs specify ACTSmart2. Important As with any Access Control system, always ensure there is an alternate means of escape in the event of the unit failing to operate due to power loss or in the event of fire. Product Specification Number of Users Supply Voltage Current Consumption Output Current Sink Operating Temperature Door Open Time Max. ACTSmarts per network Length of network Relay Contact Rating Programmable Inputs Programmable Input/Outputs Controller Size Controller Weight Water Resistance Construction 1000 12 - 24 V DC (linear PSU) or AC (standalone only) 50mA (nominal), 80mA (maximum) 100mA -25 to +60 degrees C 0 - 255 seconds 8 1.4km maximum 5A / 250Vac 1 2 Flush Mount: 100 x 110 x 20 mm Surface Mount: 100 x 110 x 35 mm 200 grams High IP67 Rugged Polycarbonate housing with stainless steel keys and potted electronics. Ordering Information Model ACTSmart Proximity Only ACTSmart PIN and Proximity ACTSmart PIN Only 4 Part Number ACT 1070 ACT 1080 ACT 1090 ACTSmart2 Operating and Installation Manual Rev. 1.1 30 Second Programming Guide ACTSmart2 Pin & Prox (1080) (For typical Standalone System) 1. Enter Programming Mode. Press button followed by the programming code (default is 9999) The LED will flash amber. 2. Add a Batch of Cards Press 10, then present the first card in the batch followed by the last card in the batch. Press button to complete. 3. Add a PIN Code Press 12, and then enter a 4-digit PIN code. Press button to complete. (Option 40 - Card or PIN.) 4. Set Desired Door Relay Active Time Press 20, and then enter the desired number of seconds from 000-255 (three digits with leading zeros). Press button to complete. 5. Change Programming code Press 23, then enter new 4-digit programming code. 6. Exit Programming Mode Press the button. The LED turns red. The ACTSmart is now ready for normal use. Note: The ACTSmart may be returned to its factory default condition at any time by entering the programming mode and pressing 80 followed by the button. For information on programming the advanced features and networking the ACTSmart range, please refer to the complete programming guide. access control TECHNOLOGY Unit 8, Tallaght Business Centre, Whitestown, Dublin 24, Ireland Tel: 353-1-4622585 Fax: 353-1-4622587 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.ie Copyright © 2005 Access Control Technology Ltd. 5 ACTSmart2 Operating and Installation Manual Rev. 1.1 30 Second Programming Guide ACTSmart2 PIN Only (1090) 1. Enter Programming Mode. Press button followed by the programming code (default is 9999) The LED will flash amber. 2. Add a PIN Code Press 12, and then enter a 4-digit PIN code. Press button to complete. 3. Set Desired Door Relay Active Time Press 20, and then enter the desired number of seconds from 000-255 (three digits with leading zeros). Press button to complete. 4. Change Programming code Press 23, then enter new 4-digit programming code. 5. Exit Programming Mode Press the button. The LED turns red. Note: The ACTSmart may be returned to its factory default condition at any time by entering the programming mode and pressing 80 followed by the button. For information on programming the advanced features and networking the ACTSmart range, please refer to the complete programming guide. 6 ACTSmart2 Operating and Installation Manual Rev. 1.1 Programming Summary Code 10 11 12 13 14 15 16 17 18 20 21 22 23 24 26 30 31 32 33 34 35 36 37 38 39 40 41 43 50 51 52 53 60 61 62 70 71 72 73 80 Function Add Card Batch Delete Card Batch Add PIN Code Delete PIN Add Card and PIN Delete Card and PIN Add Card Batch using keypad Delete Card Batch using keypad Add Random Card Set Door Relay Time Set Door Ajar Time Set Guest Buzzer Time Change Programming Code Change Number of PIN Digits Limit Number of Users Door Chime Silent Operation Lock-saver (Anti Tailgating) Toggle Door Forced Alarm Door Ajar Alarm Guest Button Duress Codes Network Master Card and PIN Card or PIN Card and any PIN Pulse Door Armed Set Programmable Input Set AUX I/O 1 Set AUX I/O 2 Quick I/O Setup Assign Door Numbers Find Door Number Find Door Numbers Add Card Batch for Second Door Add PIN code for Second Door Add Card and PIN for Second Door Add Random card for Second Door Default Unit 7 Default 5 seconds 30 seconds 2 seconds 9999 4 1000 Off Off Off Off On On On Off Off Off Off Off Off Door Release Button Door Contact Door Alarm ACTSmart2 Operating and Installation Manual Rev. 1.1 ACTSmart Operation The ACTSmart family consists of Proximity only, Pin and Proximity and PIN only units. Each ACTSmart can operate in standalone mode. Up to 8 ACTSmart devices can be connected on a RS485 network. The ACTSmart will support a maximum of 1000 tokens. A token may be a card, keyfob or a PIN code. Each unit is contained in a rugged polycarbonate housing, with stainless steel keys and potted electronics, allowing for indoor and outdoor installation. Programming the unit is achieved via the keys and LED. For quick and easy installation, the ...