User manual ADE OPTIMA G3 INTRUDER SYSTEM

Operating instructions Contents Unset system indications - - - - - - - - - - Set System indication - - - - - - - - - - - Access codes - - - - - - - - - - - - - - - How to operate Personal Attack - - - - - How to unset system in alarm - - - - - - Programs 1, 2 and 3 - - - - - - - - - - - - How to set the system (on program 1) - - Push to Set Switch - - - - - - - - - - - - - Keyswitch Set - - - - - - - - - - - - - - - Faults during setting - - - - - - - - - - - - How to unset the system (turn off) - - - - How to set program1,2 or 3- - - - - - - - How to Quick set - - - - - - - - - - - - - How to Omit zone(s) on setting system - - Fire Alarm - - - - - - - - - - - - - - - - How to set Chime zone - - - - - - - - - - Operator's Program mode - - - - - - - - - To exit operation at any time - - - - - - - - How to enter Operator's program mode - How to view the event log - - - - - - - - - How to create/omit User 2 code - - - - - - How to change current user code - - - - - How to create/change/omit the Duress code How to carry out Alarm and Walk tests- - Servicing organisation details - - - - - - - - Quick Reference - - - - - - - - - - - - - - 1 1 2 2 2 2 3 3 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 7 7 8 Accenta/Optima G3 Intruder system How to unset system in alarm Enter your code. Entering the code will turn the alarm off and the cause of the alarm will be displayed. After investigation press Reset to clear the indication. n n n n Bell Alarm FIRST ZONE IN ALARM OTHER ZONES IN ALARM Investigate the Alarm Reset ALL ZONE Strobe Off Day Access codes Note: If the alarm indication does not clear, then the system may need to be reset by the installation engineer, contact you installer for further information. Programs 1, 2 and 3 Access codes There are two User codes used in the system, all are 4 digit and can be set to any number from 0000 to 9999, signified by: n n n n The user 1 and 2 codes have the same operation for testing, Setting and Unsetting, but user 1 code which is usually considered to be the Managers code has the authority to add, change or delete the user 2 code and Duress code. The panel uses 3 Part Set routines known as Programs. In each Program the exit mode can be changed and the zone may be set up to have a different function. The examples below show how 3 typical Programs could be used in a house. Program 1 To arm all of the zones and become Set as the user leaves the property and closes the final door. Program 2 To protect the perimeter of the property in the evening and become Set after say 20 seconds. Program 3 To protect the downstairs areas of the house at night and become Set silently. The above are purely examples. The installer has the ability at the programming stage to configure all the circuits to the customer's exact requirements. ÿ ÿ User 1 code - 0123 factory set User 2 code - not programmed. How to operate Personal Attack Personal Attack buttons on the keypad are used to activate the alarm, irrespective of whether the system is armed or not. Press Simultaneously: 9 4 2 4PI175 issue 1_6/01 Accenta/Optima G3 intruder system Operating instructions How to set the system (on program 1) The green Day indicator should be showing. Day Enter your code number and check n n n n that the system is clear (none of the 10seconds Exit beep insistent beeps zone indicators are showing). The Day sounder will now produce an exit o/p ARC beep tone and you Set output should leave by the approved route. The system will Set as the beep tone stops. How to unset the system (turn off) On entering the premises an entry beep tone comes on. Enter your code, the green Day indicator is lit. The system is unset and disarmed. Entry beep Day Acknowledge Day Push to Set Switch In some systems a Push to Set switch may be fitted outside the premises near to the main exit door. This should be used to complete the setting procedure once the building has been vacated. As the switch is operated, the exit beep tone will stop and a chime tone will be produced to acknowledge setting. o/p ARC Unset output How to set program1,2 or 3 The green Day indicator should be showing. Day Enter your code number and the n n n n exit beep tone will start. Press Exit beep the Prog key and ZONE 1-3 Prog Exit beep the exit tone will stop. Press 1, 2 2 Or 3 1 or 3 for the required 10 seconds Exit beep insistent beeps program, the sounder will Day beep to o/p ARC acknowledge the Set output program number. The exit beep tone will start and you should leave by the approved route. The system will Set as the beep tone stops. It is important that you follow the correct procedure when setting the system. After leaving the protected area it is absolutely essential that you wait until the exit tone stops, before assuming the system has set. Keyswitch Set Your system may have been fitted with a remote keyswitch. This can be used as an alternative to arming the system with a code and will set Program 1. Where a keyswitch is used it may be necessary on occasions to allow it to catch up with the system. For example if the alarm was set with a code, to Unset with the keyswitch, it would have to be momentarily turned to Set then returned to Unset. Faults during setting If the system is not clear when you try to Set it, the sounder will produce an open zone tone and the fault will be displayed. Either re-enter your code to turn off and investigate or omit the faulty zone(s) from the system. 4PI175 issue 1_6/01 3 How to set the system (on program 1) n n n n Operating instructions Accenta/Optima G3 Intruder system How to Quick set During the exit period (on entering User code) Day the system may be Set Set the system or quickly by pressing Set. This removes the exit time Set a Program period. Set 5 seconds insistent beeps Day How to set Chime Zones Example: To set zone 3 and 4 to chime, Press: Chime 3 Day 4 Reset If you omit zones and require Quick Set, you will need to press Set twice. Chime Timeout after 5 seconds if no selection is made Day Chime o/p ARC Set output 0 Deselect all zones (Factory default - no chime) Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Appropriate Zone indicator is lit to show chime zone(s) Zone n Chime selected Zone n Chime deselected How to Omit zone(s) on setting system Press number button to select / deselect Zone Chime 1 2 3 4 5 6 7 8 During the exit period after entering User code and selecting a Day program press Set the system or Set a Program and while theOMIT, the exit tone will stop and zones system is setting: that are about to be Omit ZONE(S) TO BE ARMED armed will be displayed. Key in Exit beep the zone number(s) to be omitted which Press the zone(s) n to be omitted will flash to confirm selection. Zone ZONE(S) TO BE OMITTED indicators which show steady are still Set about to be armed. 10 seconds Exit beep insistent beeps When the selection is complete press Day Set and the exit tone o/p ARC will start. Set output If a zone refuses to be omitted, it may be because the engineer has programmed the panel to prevent you from turning off the zone. If in doubt ask your installer for advice. How to Quick set Reset Leave chime mode Day Fire Alarm The fire zone will operate on detection of a fire, whether the system is Set or Unset, when configured as a 24 hour zone, and cause a distinctive internal sounder tone. The external sounders will pulse on and off at 2 second intervals and all keypad indicators will flash to attract attention. Chime is a low security monitoring system for use when the system is Unset. When a zone that is set to chime is operated, the internal sounder will produce a low volume two stage warning tone and the Zone indicator will show. The indicator may be cancelled by pressing Reset. Chime is particularly useful in a shop to warn of a customer presence or in a house to warn that a door or particular area has been accessed. Any zone may set to be on or off chime by pressing the CHIME key and then keying in the required zone number(s). Key 0 to cancel all zones from chime. After a few seconds the system will automatically return to the Day mode. 4PI175 issue 1_6/01 4 Accenta/Optima G3 intruder system Operating instructions Operator's Program mode The information below shows the programmable options available and how to change them. Once the programming mode has been accessed, each section may be changed in any order. As each operation is completed the system will automatically return to top level of program mode. How to view the event log The panel can hold up to 8 previous events which can be scrolled automatically or manually. The automatic scroll starts with the newest event ( number 8) to the oldest one ( number 1). Example: To view up to 8 previous events and thereafter to stop the event scroll, Press: Prog 0 1 2 3 Chime Reset Note: When programming the system should be in the Day mode, with the Day and Power indicators lit. Enter Operator's program mode Chime View the event log Tamper To exit operation at any time On pressing the Reset key you will quit the current level of operation. Reset Automatic event scroll Starting from event 1 to 8 To manually scroll View event 1 1 (oldest event) 2 3 Zone, PA and Tamper indicators will be lit to show zone in alarm. Flashing indicates the first zone in alarm. Day indicates status of panel at the time of alarm Quit the current function Leave Engineering menu Down one menu level View event 2 View event 3 View event 4 View event 5 View event 6 View event 7 How to enter Operator's program mode To enter the Operator's program mode the system should be in Day Prog mode with the Day and ZONE 1 - 8 Power indicator lit. Momentarily On 0 1 2 3 4 5 6 7 8 View event 8 (Newest event) Chime Resume automatic scroll Acknowledge Tamper Day Reset Stop event scroll / view Leave program mode Day Acknowledge Tamper Tamper 4PI175 issue 1_6/01 5 Operator's Program mode Operating instructions Accenta/Optima G3 Intruder system How to create/omit User 2 code User 1 code which is usually considered to be Example: To create user 2 the Managers code 4567, Press: code has the Prog 0 1 2 3 7 authority to add, change or delete 4 5 6 7 Reset the user 2 code. Enter Operator's program mode Change / omit User code 2 7 (By user 1 only) Attack How to create/change/omit the Duress code The Duress code is used in a hold up situation where there is pressure to Set or Unset the system. Entry of the code will allow the system to work normally but also generate a silent PA type alarm by operating the PA communicator output. The duress code in not preprogrammed and can be created. Example: To createduress 5555, Press: Prog ZONE 1-4 0 5 1 5 2 5 3 Reset 9 How to create/omit User 2 code n n n n New code 5 NOTE - The sounder will produce a flat beep if code is rejected. Or Omit To omit the user 2 code Enter Operator's program mode Change / Omit the Duress 9 Code (By user 1 only) Attack Rising beeps ZONE 1-4 Attack ZONE 1-4 Reset Leave program mode Day Acknowledge Tamper n n n n New duress code How to change current user code Rising beeps You can change the current user 1 or user 2 Example: To change user 1 code for security code from 0123 to 7777, Press: reason. Prog ZONE 1-4 Attack 0 7 1 7 2 7 3 Reset 8 Reset Leave program mode Day Acknowledge Tamper 7 Enter Operator's program mode 8 Change the code of Current user (either User 1 or User 2) Attack ZONE 1-4 n n n n Current user new code NOTE - The sounder will produce a flat beep if code is rejected. Rising beeps ZONE 1-4 NOTE - Factory default code for User 2 is not programmed Attack Reset Leave program mode Day Acknowledge Tamper 6 4PI175 issue 1_6/01 Accenta/Optima G3 intruder system Operating instructions How to carry out Alarm and Walk tests The alarm test function allows you to test the Strobe, Bell, Low and high volume sounders of the system. The walk test function allows each detector to be checked in order to verify that they are functioning correctly. Example: To start bell test and thereafter to stop bell test. Prog 0 1 2 3 0 3 0 Reset Reset Enter Operator's program mode 0 Alarm test Attack Press zero to turn off options 2,3,4 and 5 before selecting a new one 2 Strobe test Strobe On Bell on Day Day 3 Bell test 4 5 6 Low volume sounder High volume sounder Walk test internal low volume sound internal high volume sound Strobe Day Day Strobe On Day x1 for zone 1 x2 for zone 2 | x4 for zone 4 flat x1 for zone 5 flat x2 for zone 6 | flat x4 for zone 8 Rapid for PA Rapid for Tamper Appropriate zone lights are lit(latched) Zones 0 OFF Day Reset Attack Reset Exit current level Attack Leave program mode Day Acknowledge Tamper Tamper Servicing organisation details Servicing organisation name: ______________________________________ Telephone number: ______________________________________ Date of installation: ______________________________________ Account Number: ______________________________________ Installation Date: ______________________________________ Bell Time:_____________________________ Bell delay______________________________ Area protected Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 T = Timed (Entry/Exit - Zone) TI = Time Inhibited (Access zone to keypad) I = Immediate (All zones armed to give full alarm) Program 1 Program 2 Program 3 4PI175 issue 1_6/01 7 How to carry out Alarm and Walk tests Quick Reference 8 To Set a Program Day Entry beep Day Day To Set the system (Program 1) n n n n n n n n Day To Un-set the system To Quick Set the system Bell Alarm FIRST ZONE IN ALARM To Reset Alarm state To Omit zones on Setting system Day Quick Reference n Exit beep n n Exit beep Acknowledge n n Set Omit OTHER ZONES IN ALARM Exit beep 5 seconds insistent beeps Day n n n Prog ZONE 1-3 Set the system or Set a Program ZONE(S) TO BE ARMED Operating instructions Exit beep Set the system or Set a Program and while the system is setting: 10seconds insistent beeps 1 Or Day 10 seconds insistent beeps 2 3 Exit beep Day Day Investigate the Alarm Reset o/p ARC Set output o/p ARC Set output o/p ARC Unset output ALL ZONE o/p ARC Set output n Press the zone(s) to be omitted ZONE(S) TO BE OMITTED Strobe Off Day The panels conform to the requirements of the European EMC and Low Voltage directives, and carries the CE mark Set Exit beep Operator's program mode menu map n 8 Chime Chime Operator's Progam Mode Prog n Chime n n To exit Operator's program mode Reset To set Chime zone 0 7 Alarm test Change / omit User code 2 (By user 1 only) Change the code of Current user (either User 1 or User 2) View the event log n n n n n Reset 10 seconds insistent beeps Day 2 Omit Strobe test To omit the user 2 code Leave program mode 1 n n n New code Automatic event scroll Starting from event 1 to 8 For manual scroll 1 Zone to chime 3 Bell test Reset 4 8 View event 8 (Newest event) Chime Leave program mode View event 1 (oldest event) 8 Reset o/p ARC Set output Low volume sounder Change / Omit 9 the Duress Code (By user 1 only) n Reset Reset 5 High volume sounder Resume automatic scroll Normal indications of an Unset system Day Power 6 n n n 0 Walk test Press zero to turn off options 2,3,4 and 5 before selecting a new one Leave program mode Reset Alarm indications Stop event scroll / view Reset Reset Exit current level Quit the current function Leave program menu Down one menu level Bell On Leave program mode Strobe Alarm Accenta/Optima G3 Intruder system 4PI175 issue 1_6/01 Reset Leave program mode