Contents For the User Safety information Description of the appliance - Rinse conditioner dispenser - Spray arm - Coarse filter - Fine filter - Detergent dispenser - Salt container For the Installer 3 4-5 Technical specifications Unpacking - Damages - Use - Protecting the machine against freezing 13 14 Installation 6 7 8 9 10 - Positioning - Water inlet - Water drainage - Electrical connection 15 The control panel - Audible signals Adjusting the water softener Loading the dishwasher - How to load the dishes Rukowodstwo po \kspluatacii 16 Programme chart Using the appliance - Starting the programme - Interrupting the programme temporarily - Cancelling the programme - Cancelling the drying phase - Setting the delay start - Switching the dishwasher off / Unloading - Cleaning the dishwasher In the event of a fault Service - Service and spare parts 11-12 12 13 Information for test centres Guide to use the instruction book The following symbols will be found in the text to guide you throughout the instructions: Safety instructions Step by step instructions Hints and tips Environmental information -2- Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety. Installation and servicing G G All installation and service work done on the product must be carried out by a qualified technician. Work performed by persons with inadequate knowledge may adversely affect the satisfactory functioning of the product and may cause personal injury or damage. Before any work is carried out on the dishwasher, it must be isolated from the electrical supply, by unplugging the power cord or removing the fuse. Water connection shall be made via an easily accessible stopcock. The power cord must be plugged into an earthed socket, which need to be easily accessible. Permanent installation must only be carried out by an authorised electrician. If the power cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. Make sure that the power cord is not nipped or otherwise damaged and that the hoses do not get crushed or kinked when moving the dishwasher in connection with installation or cleaning etc. Servicing and possible repairs must be carried out by a service company authorised by the manufacturer. Use only spare parts supplied by these. Never try to repair the dishwasher yourself. Do not place sharp knives with their points upwards. It is much safer to lay them horizontally in the basket. Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody injuring themselves on the open door, if the dishwasher is placed under the worktop. If you take any dishes out of the machine before the end of the dishwashing cycle, it is extremely important to rinse them thoroughly under running water to remove any remaining detergent. In the event of flooding or leakage, shut off the water supply immediately by closing the stopcock and disconnect the power supply by unplugging the power cord or removing the fuse. When removing the electrical plug, grip the plug, not the lead. There is always a certain risk of leakages in any machine connected to a water supply, no matter what water safety features it may have. Therefore it is advisable always to turn off the water supply tap when the machine is not in use. G G G G G G G G Disposal - packaging: All materials used in packaging this appliance are environmentally-friendly. The various plastics used are identified and can be recycled: G G Child Safety G PE stands for polyethylene, which is used for the bag around the appliance and the bag in which these instructions were supplied. PS stands for polystyrene (moulded), which is used for the sections of packaging needed to cushion the appliance. The dishwasher should be used by adults only. Do not let children play with the controls or other parts of it. Remember that the plastic bags included in the packaging can be fatal playthings for small children. Keep all detergents in safe place out of children´s reach. Prevent children from sitting, swinging or standing on the open door. G G G The cardboard components of the packaging are made from recyclable paper and should be taken to a collection point for recycling. G - old apparatus: The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. 822 61 11-58 During Use G This dishwasher is designed solely for washing household utensils suitable for machine washing. Using it for other purposes could lead to physical injury or damage to property and invalidate the guarantee. Avoid opening the door while the dishwasher is running, as hot steam may escape. Only use detergent specifically designed for use in dishwashers. G G -3- Description of the appliance 1 2 3 4 5 6 Rinse conditioner dispenser Spray arm Coarse filter Fine filter Detergent dispenser Salt container -4- Rinse conditioner dispenser 1 Use of a rinse conditioner will result in cleaner and faster drying of the load, since it helps water to run off. Too much conditioner may result in streakiness, too little may cause white spots. The dispenser holds about 140 ml. This is enough for 40-70 wash cycles, depending on the dosage setting. When the rinse conditioner level is approaching the bottom of the scale it is time to refill the dispenser. Adjust the dosage setting according to the hardness in the water. Begin with the lowest dosage setting and increase if necessary by turning the arrow clockwise. 1. Swivel out the filler trough. 2. Fill up with rinse conditioner until the level reaches up to the red mark on the level indicator tube; do not overfill. 3. Wipe off any spillage carefully to prevent excessive foaming during the next wash programme. 4. Close the filler trough afterwards. Do not fill the rinse aid dispenser with liquid detergent. Salt container 6 This dishwasher is equipped with a water softener for hard water, therefore shall the rinse aid dispenser be set for a low dosage. The lime in hard water causes white deposits to occur on dishes and to the interior of the dishwasher. To prevent this, the water has to pass through a special container where the hardness is removed. Since the water softener uses coarse dishwasher salt, you will have to refill the salt container after a certain number of dishwashing cycles. It is extremely important, that the salt container is filled up with the coarse dishwasher salt before using the dishwasher for the first time, if you live in an area where the water is calciferous. The indicator light on the control panel is lit when the container requires refilling. 1. Unscrew the filler cap to the salt container anticlockwise. 2. Fill the salt container with water (only the first time). 3. Fill the container with coarse salt, using the funnel supplied. 4. Remove the funnel and wipe off any spillage around the filler opening. 5. Screw the filler cap back properly in place. The water softener is now ready for the first load of dishes. Always make sure that there is coarse grained salt in the container, which holds about 1 litre. Use only special salt for dishwashing machines, ordinary domestic salt can damage the water softener. How to adjust the water softener, see chapter "Adjusting the water softener". Spray arm 2 It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. If the spray arm needs cleaning, unscrew the nut clockwise, remove the washer and lift off the spray arm. Clear the holes and shake out any food remnants. Coarse filter 3 The purpose of the coarse filter is to catch large objects such as toothpicks and pieces of eggshell. Make sure that the filter is always clean. Lift it out and rinse it under running water whenever necessary. Fine filter 4 It is just as important to keep this filter clean. A dirty or clogged filter will always impair washing efficiency. The fine filter can easily be lifted out for cleaning when you have removed the coarse filter. Detergent dispenser 5 Consult the instructions on the detergent packet and fill the compartment. Remember that the instructions usually refer to full-size dishwashers, for example when using detergent tablets, it is sufficient to use just half a tablet. Only use detergents specially designed for dishwashers. -5- The control panel Programme lamps 1 2 On/Off button Programme selection/ Delay start Cancel button button Control lamps Programme selection/cancel button is used to: · select the programme · set the water softener · deactivate/activate the audible signal · cancel a dishwashing cycle Control lamps: Shows that: · Wash cycle in progress · Refilling of salt is necessary · Programme cycle ended The programme cycle ended lamp has also other functions of visual signalling: · on the setting of the water softener · when deactivating/activating the audible signal · with malfunction of the machine Audible signal Audible signal have been introduced to help indicate which operations the dishwasher is performing: · end of washing programme · malfunction of the machine 2. Press the programme selection/cancel button and hold it pressed until indicator lamp 1 starts to flash and lamp 2 lights up. 3. Directly after press the programme button again, lamp 1 will change from flashing to continual illumination and goes out after approx. 3 seconds. Lamp 2 starts to flash and the indicator for the ended programme cycle goes on. Press the button once more and the lamp for the ended programme cycle goes out. The audible signal is now off. 4. Press out the On/Off button to complete the setting. To activate the function again, follow steps above, until the lamp for the ended programme cycle goes on again. Deactivation/activation of the audible signal The audible signal is activated when leaving the factory. 1. To deactivate the signal: With the dishwasher switched off, press in the On/Off button. The ended programme lamp flashes. If one of the programme lamps is illuminated, this wash programme is activated. The programme must be deselected: press and hold the programme selection/cancel button for approx. 3 seconds. The programme lamp goes out and the indicator for the ended programme cycle flashes indicating that the programme has been cancelled. -6- Adjusting the water softener To prevent limescaling on the dishes and to the interior of the dishwasher, the dishes must be washed with soft water. This dishwasher is equipped with a water softener, where tapwater which is harder than 4 °d (german degree) is softened. Adjust the water softener according to the table below for the water hardness level for your area. Contact your local Water Authority to find the exact water hardness level for your area. The water softener has 10 settings: Water hardness level °d 1) > 24 22 - 24 20 - 22 18 - 20 16 - 18 13 - 16 10 - 13 7 - 10 4-7 below 4 mmol/l 2) > 4,2 3,9 - 4,2 3,6 - 3,9 3,2 - 3,6 2,8 - 3,2 2,3 - 2,8 1,8 - 2,3 1,2 - 1,8 0,7 - 1,2 below 0,7 Setting on the water softener 10 9 8 7 6 5* 4 3 2 1 no salt is needed Number of light flashes 10 9 8 7 6 5 4 3 2 1 1) german degree of measurement for the water hardness 2) millimol, internationel unit for water hardness *) factory setting In the following setting, the dishwasher must be switched off and all programmes completed. See chapter "Using the appliance" for information on how to complete the programme. 1. Press in the On/Off button. 2. Press the programme selection/cancel button and hold it pressed until indicator lamp 1 starts to flash and lamp 2 illuminates with a fixed light. Lamp 2 goes out after approx. 3 seconds and simultaneously the ended programme cycle indicator starts flashing. - The number of flashes for the ended programme cycle are equivalent to the set water hardness level. - This sequence of flashes is repeated several times after a few seconds pause. 3. The water hardness level is ra ...