User manual AEG-ELECTROLUX ESL63010

156997950en prov.qxp 1/22/2007 12:31 PM Page 1 user manual Dishwasher ESL 63010 156997950en prov.qxp 1/22/2007 12:31 PM Page 2 We were thinking of you when we made this product 156997950en prov.qxp 1/22/2007 12:31 PM Page 3 welcome to the world of Electrolux electrolux 3 Welcome to the world of Electrolux You've chosen a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. Electrolux ambition is to offer a wide variety of quality products that would make your life even more comfortable. You can look at some examples on the cover in this manual. But now it's time to study this manual and start using and enjoying the benefits from your new machine. We promise that it'll make your life a little easier. Good luck! 156997950en prov.qxp 1/22/2007 12:31 PM Page 4 4 electrolux contents Contents Safety information Product description Control panel First use Daily use Washing programmes Care and cleaning Something not working Technical data Hints for test institutes Installation Environment concerns Guarantee/Customer Service 5 7 8 11 15 24 25 27 30 32 33 36 37 The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information 156997950en prov.qxp 1/22/2007 12:31 PM Page 5 safety information electrolux 5 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. Correct use This dishwasher is only intended for washing household utensils suitable for machine washing. Do not put any solvents in the dishwasher. This could cause an explosion. Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket. Only use products (detergent, salt and rinse aid) suitable for dishwashers. Avoid opening the door whilst the appliance is in operation, hot steam may escape. Do not take any dishes out of the dishwasher before the end of the dishwashing cycle. After use, isolate the appliance from the power supply and turn off the water supply. This product should be serviced only by an authorised service engineer, and only genuine spare parts should be used. General safety Dishwasher detergents can cause chemical burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer. The water in your dishwasher is not for drinking. Detergent residues may still be present in your machine. Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves. Do not sit or stand on the open door. Child safety This appliance is designed to be operated by adults. Don't allow children to use the dishwasher unsupervised. Keep all packaging well away from children. There is risk of suffocation. Keep all detergents in a safe place out of children's reach. Keep children well away from the dishwasher when the door is open. 156997950en prov.qxp 1/22/2007 12:31 PM Page 6 6 electrolux safety information Installation Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier. All packaging must be removed before use. Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person. For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way. Never use the dishwasher if the electrical supply cable and water hoses are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible. Contact your local Service Force centre, in order to avoid hazard. All sides of the dishwasher must never be drilled to prevent damage to hydraulic and electric components. For electrical and water connection carefully follow the instructions given in specific paragraphs. 156997950en prov.qxp 1/22/2007 12:31 PM Page 7 product description electrolux 7 Product description 1 Upper basket 2 Water hardness dial 3 Salt container 4 Detergent dispenser 5 Rinse aid dispenser 6 Rating plate 7 Filters 8 Lower spray arm 9 Upper spray arm 156997950en prov.qxp 1/22/2007 12:31 PM Page 8 8 electrolux control panel Control panel 1 On/Off button 2 Delay start button 3 Programme selection / cancel button 4 Indicator lights Indicator lights End of programme Illuminates when a washing programme has ended. It also has added functions of visual signalling as: - the setting of the water softener, - activation/deactivation of the audible signals, - intervention of an alarm due to the malfunction of the machine. Illuminates when the rinse aid has run out. Rinse aid Salt Illuminates when the special salt has run out. 156997950en prov.qxp 1/22/2007 12:31 PM Page 9 control panel electrolux 9 Audible signals The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salts that take longer to dissolve then this can take longer. The function of the machine is not affected. Setting mode The appliance is in setting mode when all programme indicator light are off and end of programme indicator light is flashing. Audible signals have been introduced to help indicate which operations the dishwasher is performing: - end of programme - intervention of an alarm due to malfunction Factory setting: audible signals activated. It is possible to deactivate the audible signals, using the programme selection/cancel button. Deactivation/activation of the audible signals Always remember that when: - setting the water softener, - activating/deactivating the audible signals, the appliance MUST be in setting mode. If a programme indicator light is illuminated and end of programme indicator light is illuminated with fixed light, the last performed or selected programme still set. In this case, to return to setting mode, the programme has to be cancelled. 1. Press and hold the programme selection/cancel button until the light of the set programme turns off and the end of programme indicator light is flashing. 2. Release the programme selection/cancel button. 1. Press the On/Off button. The dishwasher must be in setting mode. 2. Press and hold the programme selection/cancel button until programme light 1 flashes and programme light 2 illuminates with a fixed light. 3. Press programme selection/cancel button again, programme light 1 illuminates with a fixed light and programme light 2 starts flashing. 156997950en prov.qxp 1/22/2007 12:31 PM Page 10 10 electrolux control pane 4. Wait until: - programme light 1 turns off, - programme light 2 goes on flashing - the end of programme indicator light illuminates with a fixed light, indicating that the audible signals are activated. 5. To deactivate the audible signals, press the programme selection/cancel button again: the end of programme indicator light turns off indicating that the audible signals are deactivated. 6. To memorise the operation, switch off the dishwasher. To activate again the audible signals simply follow the above operations until the end of programme indicator light illuminates. 156997950en prov.qxp 1/22/2007 12:31 PM Page 11 first use electrolux 11 First use Before using your dishwasher for the first time: Ensure that the electrical and water connections comply with the installation instructions Remove all packaging from inside the appliance Set the water softener Pour 1 litre of water inside the salt container and then fill with dishwasher salt Fill the rinse aid dispenser Set the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these minerals and salts, the harder your water is. Water hardness is measured in equivalent scales, Clarke degrees (°dH), French degrees (°TH) and mmol/l (millimol per litre - international unit for the hardness of water). The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area. Adjusting the water hardness setting manually 2 2 2 2 2 2 1 1 1 1 electronically level 10 level 9 level 8 level 7 level 6 level 5 level 4 level 3 level 2 level 1 yes yes yes yes yes yes yes yes yes no * Use of salt When using combi detergents tablets («3 in 1», «4 in 1», «5 in 1», etc...) follow the instructions given in "Use of detergent". Water hardness Clarke 64 - 88 53 - 63 46 - 52 36 - 45 28 - 35 23 - 27 18 - 22 13 - 17 5 - 12 <5 °TH 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 33 - 39 26 - 32 19 - 25 7 - 18 <7 mmol/l 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 3,3 - 3,9 2,6 - 3,2 1,9 - 2,5 0,7 - 1,8 < 0,7 * no salt is necessary 156997950en prov.qxp 1/22/2007 12:31 PM Page 12 12 electrolux first use The water softener must be set in both ways: manually, using the water hardness dial and electronically. Setting manually The dishwasher is factory set at position 2. 1. Open the dishwasher door. 2. Remove the lower basket from the dishwasher. 3. Turn the water hardness dial to position 1 or 2 (see table). 4. Replace the lower basket. 3. Wait until: - programme light 2 turns off, - programme light 1 goes on flashing - the end of programme indicator light starts flashing: the nimber of flashes corresponds to the current level set. The flashing is repeated with a pause of a few seconds. Examples: 5 flashes, pause, 5 flashes, pause, etc... = level 5. Setting electronically The dishwasher is factory set at level 5. 1. Press the On/Off button. The dishwasher must be in setting mode. 2. Press and hold the programme selection/cancel button until programme light 1 flashes and programme light 2 illuminates with a fixed light. 4. To change the level, press the programme selection/cancel button. Each time the button is pressed the level increase. (level 1 follows level10). The end of programme light indicates the new setting. 5. To memorise the operation, switch off the dishwasher by pressing the On/Off button. 156997950en prov.qxp 1/22/2007 12:31 PM Page 13 first use electrolux 13 Filling with dishwasher salt 4. Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket. 5. Replace the cap tightly turning it clockwise until it stops with a click. Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt or salty water, which may have been spilt, remaining on the bottom of the machine for any period of time, which may cause corrosion. Do not worry if water overflows from the unit when filling with salt, this is quite normal. To fill: 1. Open the door, remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise. 2. Pour 1 litre of water inside the container (this is necessary only before filling with salt for the first time). 3. Using the funnel provided, pour in the salt until the container is full. 156997950en prov.qxp 1/22/2007 12:31 PM Page 14 14 electrolux first use Filling with rinse aid Rinse aid ensures thorough rinsing, and spot and streak free drying. Rinse aid is automatically added during the last rinse. 1. Open the container by pressing the release button (A). According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage). The dose is factory set in position 4. Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades. 3. Ensure that the lid is closed after every refill. 2. Add the rinse aid in the container. The maximum level for filling is indicated by "max". The dispenser holds about 110 ml of rinse aid, which is sufficient for between 16 and 40 dishwashing cycles, depending upon the dosage setting. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash. Only use branded rinse aid for dishwashers. Never fill the rinse aid dispenser with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance. 156997950en prov.qxp 1/22/2007 12:31 PM Page 15 daily use electrolux 15 Daily use Check if it's necessary to refill with dishwasher salt or rinse aid Load cutlery and dishes into the dishwasher. Fill with dishwasher detergent . Select a wash programme suitable for the cutlery and dishes. Start the wash programme. - Lay small objects in the cutlery basket. Plastic items and pans with teflon have a tendency to retain water drops; these items will not dry as well as porcelain and steel items. Loading cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. Before loading the dishes, you should: - Remove all left over food and debris. - Soften remnants of burnt food in pans When loading the dishes and cutlery, please note: - Dishes and cutlery must not impede the rotation of the spray arms . - Load hollow items such as cups, glasses, pans, etc. with the opening downwards so that water cannot collect in the container or a deep base. - Dishes and items of cutlery must not lie inside one another, or cover each other. - To avoid damage to glasses, they must not touch. 156997950en prov.qxp 1/22/2007 12:31 PM Page 16 16 electrolux daily use For washing in the dishwasher the following cutlery and dishes are not suitable: - Cutlery with wooden, horn, china or mother-ofpearls handles. - Plastic items that are not heat resistant. - Older cutlery with glued parts that are not temperature resistant. - Bonded cutlery items or dishes. - Pewter or copper items. - Lead crystal glass. - Steel items prone to rusting. - Wooden platters. - Items made from synthetics fibres. are of limited suitability: - Only wash stoneware in the dishwasher if it is specially marked as being dishwasher-safe by the manufacturer. - Glazed patterns may fade if machine washed frequently. - Silver and aluminium parts have a tendency to discolour during washing: Residues, e.g. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use. 156997950en prov.qxp 1/22/2007 12:31 PM Page 17 daily use electrolux 17 Open the door and slide out the baskets to load the dishes. The lower basket The lower basket is designed to take saucepans, lids, plates, salad bowls, cutlery etc. Serving dishes and large lids should be arranged around the edge of the basket, ensuring that the spray arms can turn freely. The cutlery basket Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their handles facing upwards. 156997950en prov.qxp 1/22/2007 12:31 PM Page 18 18 electrolux daily use If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Mix spoons with other cutlery to prevent them from sticking together. For best results we recommend you to use the cutlery grid provided (if the size and dimensions of the cutlery allow it). Glasses with long stems can be placed upside down in the cup racks. For taller items, the cup racks can be folded upwards. Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so they do not move. The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 24 cm in diameter), salad bowls, cups and glasses. Arrange items on and underneath the cup racks so that water can reach all surfaces. Before closing the door, ensure that the spray arms can rotate freely. 156997950en prov.qxp 1/22/2007 12:31 PM Page 19 daily use electrolux 19 Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in: the upper basket With upper basket raised With upper basket lowered 20 cm 24 cm the lower basket 31 cm 27 cm To move to the higher position proceed as follows: 1. Move the front runner stops (A) of the upper basket outwards and slide the basket out. When the basket is in the higher position you will not be able to use the cup racks. After loading your machine always close the door, as an open door can be a hazard. 2. Refit the basket in the higher position and replace the stops (A) in their original position. 156997950en prov.qxp 1/22/2007 12:31 PM Page 20 20 electrolux daily use Use of detergent 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent 3. All programmes with prewash need an additional detergent dose (5/10 g) that must be placed in the prewash detergent chamber (2). This detergent will take effect during the prewash phase. When using detergent tablets; place the tablet in compartment (1) Only use detergents specifically designed for use in dishwashers. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. Using no more than the correct amount of detergent contributes to reducing pollution. Fill with detergent 1. Open the lid. 4. Close the lid and press until it locks in place. 2. Fill the detergent dispenser (1) with detergent. The marking indicates the dosing levels: 1 2 156997950en prov.qxp 1/22/2007 12:31 PM Page 21 daily use electrolux 21 Detergent tablets Detergent tablets from different manufactures dissolve at different rates. For this reason, some detergent tablets do not attain their full cleaning power during short washing programmes. Therefore, please use long washing programmes when using detergent tablets, to ensure the complete removal of detergent residuals. Use of combi detergent tablets These products are detergents with a combined cleaning, rinsing and salt functions. They can also contain other different agents depending on which kind of tablets you choose («3 in 1», «4 in 1», «5 in 1» etc...). 1. Check whether these detergents are suitable for your water hardness. Follow the manufacturers instructions. 2. Select the lowest setting for water hardness and rinse aid dosage. 3. Before the start of the washing programme put the combi detergent tablet in the detergent dispenser. If the drying results are not satisfactory we recommend that you: 1. Fill up the rinse aid dispenser with rinse aid. 2. Set the rinse aid dosage to position 2. If you decide to turn back to the use of the standard detergent system we advise that you: 1. Fill up the dispensers for salt and rinse aid again. 2. Adjust the water hardness setting to the highest setting and perform 1 normal washing programme without loading any dishes. 3. Adjust the water hardness setting according to the hardness of the water in your area. 4. Adjust the rinse aid dosage. The refilling of the salt container and the rinse aid dispenser are no longer necessary. In this case the rinse aid indicator light will always remain illuminated when the machine is switched on (not all dishwasher models are foreseen with rinse aid indicator light). 156997950en prov.qxp 1/22/2007 12:31 PM Page 22 22 electrolux daily use Select and start a washing programme 3. The opening of the door will interrupt the countdown. Close the door; the countdown will continue from the point at which it was interrupted. 4. Once the delay start has elapsed the programme will start automatically. Select the washing programme and delay start with the door slightly opened. The start of the programme or the countdown of the delay start will occur only after the closure of the door. Until that moment it is possible to modify the set made. 1. Check that the baskets have been loaded correctly and that the spray arms are free to rotate 2. Check that the water tap is opened 3. Press the On/Off button. The dishwasher must be in setting mode. The end of programme indicator light is flashing. 4. Press the programme selection/cancel button until the light corresponding to the required washing programme illuminates (see "Washing programmes" chart). Close the dishwasher's door, the programme starts automatically. Interrupt or cancel a washing programme in progress ONLY if it's absolutely necessary. Attention! Hot steam may escape when the door is opened. Open the door carefully. Interrupt a washing programme in progress: Open the dishwasher door; the programme will stop. Close the door; the programme will start from the point at which it was interrupted. Cancel a washing programme in progress Open the dishwasher door; press the programme selection/cancel button for about 3 seconds, until the light of the running programme turns off and the end of programme indicator light flashes. The washing programme has been cancelled and the appliance is now in setting mode. If a new washing programme is to be selected, check that there is detergent in the detergent dispenser. Setting and starting the programme with "delay start" 1. After having selected the washing programme, press the delay start button This option allows the start of the washing programme to be delayed by 3 hours. The corresponding light illuminates, 2. Close the dishwasher's door, the countdown starts automatically. 156997950en prov.qxp 1/22/2007 12:31 PM Page 23 daily use electrolux 23 Cancelling the "delay start" To cancel a delay start in progress, open the door and press the delay start button, the corresponding light turns off. Close the door, the set washing programme will start automatically. When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off. End of the washing programme The dishwasher will automatically stop and an audible signal informs you of the end of the washing programme. Open the dishwasher door. The end of programme indicator light is illuminated. The indicator light of the programme just ended will remain on. 1. Switch off the dishwasher by pressing the On/Off button. 2. Leave the dishwasher door ajar and wait a few minutes before removing the dishes; in this way they will be cooler and the drying will be improved. Unloading the dishwasher Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down before removing from the appliance. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler than the dishes. 156997950en prov.qxp 1/22/2007 12:31 PM Page 24 24 electrolux washing programmes Washing programmes Programme Degree of soil Type of load Programme description Prewash Main wash up to 70°C 2 intermediate rinses Final rinse Drying Prewash Main wash up to 65°C 2 intermediate rinses Final rinse Drying Main wash up to 60°C Final rinse Prewash Main wash up to 50°C 1 intermediate rinse Final rinse Drying 1 cold rinse (to avoid food scraps from sticking together). This programme does not require the use of detergent. Heavy soil Intensive Crockery, cutlery, pots and pans Normal soil Normal Crockery, cutlery, pots and pans Light soil Quick Crockery and cutlery Normal soil Crockery and cutlery Rinse and Hold Any. Partial load (to be completed later in the day). 156997950en prov.qxp 1/22/2007 12:31 PM Page 25 care and cleaning electrolux 25 Care and cleaning Cleaning the filters The filters must be checked and cleaned from time to time. Dirty filters will degrade the washing result. 4. Take hold of the coarse filter (A) by the handle with the hole and remove from the microfilter (B). 5. Clean all filters thoroughly under running water. 6. Remove the flat filter from the base of the washing compartment and clean both faces thoroughly. 7. Put the flat filter back in the base of the washing compartment and ensure that it fits perfectly under the two guides (C). Before cleaning the filters ensure that the machine is switched off. 1. Open the door, remove the lower basket. 2. The dishwasher filter system comprises a coarse filter (A), a microfilter (B) and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 8. Place the coarse filter (A) in the microfilter (B) and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. 3. Turn the handle about 1/4 a turn anticlockwise and remove. 156997950en prov.qxp 1/22/2007 12:31 PM Page 26 26 electrolux care and cleaning NEVER try to remove the spray arms. If residues of soil have clogged the holes in the spray arms, remove them with a cocktail stick. External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....). Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run a 65°C wash programme without dishes using detergent. Prolonged periods of nonoperation If you are not using the machine for any period of time you are advised to: 1. Unplug the appliance and then turn off the water. 2. Leave the door ajar to prevent the formation of any unpleasant smells. 3. Leave the inside of the machine clean. Frost precautions Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it. Moving the machine If you have to move the machine (moving house etc....): 1. Unplug it. 2. Turn the water tap off. 3. Remove the water inlet and discharge hoses. 4. Pull the machine out together with the hoses. Avoid over tilting the machine during transportation. 156997950en prov.qxp 1/22/2007 12:31 PM Page 27 27 electrolux something not working something not working electrolux 27 Something not working The dishwasher will not start or stops during operation. Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the indications described in the chart, without calling out an engineer. Open the door and carry out the following suggested corrective actions. Fault code and malfunction Possible cause and solution continuous flashing of the light of the running programme, intermittent audible signal, 1 flash of the end of programme indicator light, The water tap is blocked or furred with limescale. Clean the water tap. The water tap is turned off. Turn the water tap on. The filter (where present) in the threaded hose fitting at the water inlet valve is blocked. Clean the filter in the threaded hose. The water inlet hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. The sink spigot is blocked. Clean out the sink spigot. The water drain hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. The dishwasher does not fill with water continuous flashing of the light of the running programme, intermittent audible signal, 2 flashes of the end of programme indicator light, The dishwasher will not drain continuous flashing of the light of the running programme, intermittent audible signals, 3 flashes of the end of programme indicator light, Close the water tap and contact your local Service Force Centre. Anti-flood device is activated Remember to switch off the appliance before carrying out any corrective action. 156997950en prov.qxp 1/22/2007 12:31 PM Page 28 28 electrolux something not working Malfunction The programme does not start Possible cause and solution The dishwasher's door has not been properly closed. Close the door. The main plug is not plugged in. Insert the main plug. The fuse has blown out in the household fuse box. Replace the fuse. Delay start has been set. If dishes are to be washed immediately, cancel the delay start. Once these checks have been carried out; switch on the appliance, press the programme selection/cancel button and close the door. The programme will continue from the point at which it was interrupted. If the malfunction or fault code reappears contact the Service Force Centre. For other fault codes not described in the above chart, please contact your Service Force Centre. Contact your local Service Force Centre, quoting the model (Mod.), product number (PNC) and serial number (S.N.). This information can be found on the rating plate located on the side of the dishwasher door. So that you always have these numbers at hand, we recommend you to make a note of them here: Mod. :. . . . . . . . . . . . . . . . . . . . . . . . . PNC : . . . . . . . . . . . . . . . . . . . . . . . . . S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . 156997950en prov.qxp 1/22/2007 12:31 PM Page 29 something not working electrolux 29 The wash results are not satisfactory The dishes are not clean The wrong washing programme has been selected. The dishes are arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded. The spray arms do not rotate freely due to incorrect arrangement of the load. The filters in the base of the washing compartment are dirty or incorrectly positioned. Too little or no detergent has been used. Where there are limescales deposits on the dishes; the salt container is empty or the incorrect level of the water softener has been set. The drain hose connection is not correct. The salt container cap is not properly closed. Rinse aid was not used. The rinse aid dispenser is empty. Decrease rinse aid dosing. The dishes are wet and dull There are streaks, milky spots or a bluish coating on glasses and dishes Water drops have dries onto glasses and dishes Increase rinse aid dosing. The detergent may be the cause. Contact the detergent manufacturer's consumer care line. If after all these checks, the problem persists, contact your local Service Force Centre. 156997950en prov.qxp 1/22/2007 12:31 PM Page 30 30 electrolux technical data Technical data Dimensions Width Height Depth Electrical connection Voltage - Overall power Fuse Water supply pressure 59.6 cm 81.8 - 87.8 cm 55.5 cm Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher's door Minimum Maximum 0.05 MPa (0,5 bar) 0.8 MPa (8 bar) 12 place settings 37 kg 49 dB (A) Capacity Max. weight Noise level Subject to change without notice 156997950en prov.qxp 1/22/2007 12:31 PM Page 31 technical data electrolux 31 Consumption values Programme Programme duration (in minutes) 85 - 95 105 - 115 30 140 Energy consumption (in kWh) 1.8 - 2.0 1.5 - 1.7 0.90 1.05 Water consumption (in litres) 22 - 25 23 - 25 9 16 Intensive Normal Quick Eco (Test programme for test institutes) Rinse and Hold 12 0.1 5 The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply and the amount of dishes. 156997950en prov.qxp 1/22/2007 12:31 PM Page 32 32 electrolux hints for test institutes Hints for test institutes Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Consumption values"). Test in accordance with EN 50242 must be carried out when the salt container and rinse aid dispenser have been filled with salt and rinse aid respectively and using the test programme (see "Consumption values"). Full load: 12 standard place settings Amount of detergent required: Rinse aid setting: 5 g + 25 g (Type B) position 4 (Type III) Arrangement upper basket Arrangement cutlery basket Arrangement lower basket Cup racks: position A 156997950en prov.qxp 1/22/2007 12:31 PM Page 33 installation electrolux 33 Installation Levelling Good levelling is essential for correct closure and sealing of the door. When the appliance is correctly levelled, the door will not catch on either side of the cabinet. If the door does not close correctly, loosen or tighten the adjustable feet until the machine is perfectly level. Water supply connections This dishwasher may be fed with cold water. For making the connection itself, the coupling nut fitted to the machine's supply hose is designed to screw onto a 3/4" gas thread spout or to a purpose made quick-coupling tap such as the Press-block. The water pressure must be within the limits given in the "Technical specifications". Your local Water Authority will advise you on the average mains pressure in your area. The water inlet hose must not be kinked, crushed, or entangled when it is being connected. The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut. The locknut must be correctly fitted to avoid water leaks. Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Remove all packaging before positioning the machine. If possible, position the machine next to a water tap and a drain. This dishwasher is designed to be fitted under a kitchen counter or worksurface. Attention! Carefully follow the instructions on the enclosed template for building in the dishwasher and fitting the furniture panel. No further openings for the venting of the dishwasher are required, but only to let the water fill and drain hose and power supply cable pass through. The dishwasher incorporates adjustable feet to allow the adjustment of the height. During all operations that involve accessibility to internal components the dishwasher has to be unplugged. When inserting the machine, ensure that the water inlet hose, the drain hose and the supply cable are not kinked or squashed. Fixing to the adjacent units The dishwasher must be secured against tilting. Therefore make sure that the counter it is fixed under, is suitably secured to a fixed structure (adjacent kitchen units cabinets, wall). 156997950en prov.qxp 1/22/2007 12:31 PM Page 34 34 electrolux installation (Attention! NOT all models of dishwashers have fill and drain hoses provided with locknut. In this case, this kind of facility is not possible). If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. DO NOT use connection hoses which have previously been used for an old appliance. Water outlet hose connection The end of the drain hose can be connected in the following ways: 1. To the sink outlet spigot, securing it to the underside of the work surface. This will prevent waste water from the sink running into the machine. 2. To a stand pipe provided with venthole, minimum internal diameter 4 cm. The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the bottom of the dishwasher. The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water. The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine. If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided. This appliance has been fitted with safety features which will prevent the water used in the appliance from returning back into the drinking water system. This appliance complies with the applicable plumbing regulations. Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided. 156997950en prov.qxp 1/22/2007 12:31 PM Page 35 installation electrolux 35 Electrical connection Our appliances are supplied with a security device to protect against the return of dirty water back into the machine. If the spigot of your sink has a "no return valve" incorporated this can prevent the correct draining of your dishwasher. We therefore advise you to remove it. Safety standards require the appliance to be earthed. The manufacturer accepts no liability for failure to observe the above safety precautions. Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. Always plug the mains plug into a correctly installed shockproof socket. Multi-way plugs, connectors and extension cables must not be used. This could constitute a fire hazard through overheating. If necessary, have the domestic wiring system socket replaced. In case that the electrical cable has to be replaced, contact your local Service Force centre. The plug must be accessible after the appliance has been installed. Never unplug the appliance by pulling on the cable. Always pull the plug. 156997950en prov.qxp 1/22/2007 12:31 PM Page 36 36 electrolux environment concerns Environment concerns Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. When a unit is no longer being used: - Pull the plug out of the socket. - Cut off the cable and plug and dispose of them. - Dispose of the door catch. This prevents children from trapping themselves inside and endangering their lives. 156997950en prov.qxp 1/22/2007 12:31 PM Page 37 guarantee/customer service electrolux 37 Guarantee/Customer Service Standard guarantee conditions We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. Electrolux Service Force Centre must undertake all service work under this guarantee. Any appliance or defective part replaced shall become the Company's property. This guarantee is in addition to your statutory and other legal rights. Exclusions Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of Electrolux manufacturer that are not marketed by Electrolux Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk Before calling out an engineer, please ensure you have read the details under the heading "Something not working" 156997950en prov.qxp 1/22/2007 12:31 PM Page 38 38 electrolux guarantee/customer service When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and postcode. 2. Your telephone number. 3. Clear concise details of the fault. 4. The model and Serial number of the appliance (found on the rating plate). 5. The purchase date. Please note a valid purchase receipt or guarantee documentation is required for in guarantee service calls. Customer Care For general enquiries concerning your Electrolux appliance, or for further information on Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.electrolux.co.uk Customer Care Department Electrolux Major Appliances Addington Way Luton Bedfordshire, LU4 9QQ Tel: 08705 950 950 (*) (*) Calls may be recorded for training purposes. European guarantee This appliance is guaranteed by Electrolux, in each of the countries listed in the following page, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of these countries the appliance guarantee will move with you subject to the following qualifications: The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purchase document issued by seller of the appliance. The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your country of residence for this particular model or range of appliances. The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another user. The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e. is not used for commercial purposes. The appliance is installed in accordance with all relevant regulations in force within your new country of residence. The provisions of this European Guarantee do not affect any of the rights granted to you by law. 156997950en prov.qxp 1/22/2007 12:31 PM Page 39 guarantee/customer service electrolux 39 www.electrolux.com Albania Belgique/België/Belgien Ceská republika +35 5 4 261 450 +32 2 363 04 44 +420 2 61 12 61 12 +45 70 11 74 00 +49 180 32 26 622 +37 2 66 50 030 +34 902 11 63 88 www.electrolux.fr +44 8705 929 929 +30 23 10 56 19 70 +385 1 63 23 338 +353 1 40 90 753 +39 (0) 434 558500 +37 17 84 59 34 +370 5 27 80 609 +35 2 42 43 13 01 +36 1 252 1773 +31 17 24 68 300 +47 81 5 30 222 +43 18 66 400 +48 22 43 47 300 +35 12 14 40 39 39 +40 21 451 20 30 +41 62 88 99 111 +38 61 24 25 731 +421 2 43 33 43 22 +35 8 26 22 33 00 +46 (0)771 76 76 76 +90 21 22 93 10 25 +7 495 937 7837 Rr. Pjeter Bogdani Nr. 7 Tirane Bergensesteenweg 719, 1502 Lembeek Budjovická 3, Praha 4, 140 21 Danmark Deutschland Eesti España France Great Britain Hellas Hrvatska Ireland Italia Latvija Lietuva Luxembourg Magyarország Nederland Norge Österreich Polska Portugal Romania Schweiz/Suisse/Svizzera Slovenija Slovensko Suomi Sverige Türkiye Sjællandsgade 2, 7000 Fredericia Muggenhofer Str. 135, 90429 Nürnberg Mustamäe tee 24, 10621 Tallinn Carretera M-300, Km. 29,900 Alcalá de Henares Madrid Addington Way, Luton, Bedfordshire LU4 9QQ 4 Limnou Str., 54627 Thessaloniki Slavonska avenija 3, 10000 Zagreb Long Mile Road Dublin 12 C.so Lino Zanussi, 26 - 33080 Porcia (PN) Kr. Barona iela 130/2, LV-1012, Riga Verkiu, 09108 Vilnius Rue de Bitbourg, 7, L-1273 Hamm H-1142 Budapest XIV, Erzsébet királyné útja 87 Vennootsweg 1, 2404 CG - Alphen aan den Rijn Risløkkvn. 2, 0508 Oslo Herziggasse 9, 1230 Wien ul. Kolejowa 5/7, Warsaw Quinta da Fonte - Edificio Gonçalves Zarco Q 35 - 2774 - 518 Paço de Arcos Str. Garii Progresului 2, S4, 040671 RO Industriestrasse 10, CH-5506 Mägenwil Electrolux Ljubljana, d.o.o. Traska 132, 1000 Ljubljana Electrolux Slovakia s.r.o., Electrolux Domáce spotrebice SK, Seberíniho 1, 821 03 Bratislava