User manual AEG -O-SANTO.SUPER.3274-6.KA

ÖKO_SANTO SUPER Electronic Refrigerator Operating Instructions 818 17 01-00/7 Dear customer, Before placing your new refrigerator/freezer into operation please read these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance. Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance. Important! These operating instructions are for use with several technically comparable models with varying accessories. Please observe the notes which apply to your model. 1 Notes which are important for your safety or for the proper functioning of the appliance are stressed with a warning triangle and/ or with signal words (Warning!, Caution!, Important!). Please observe the following carefully. 0 This symbol guides you step by step in the operation of the appliance. 3 2 Supplementary information regarding operation and practical applications of the appliance appear after this symbol. Tips and notes concerning economical and environmentally sound use of the appliance are marked with the cloverleaf. Explanations of the technical terminology used in the operating instructions can be found at the end in the section "Technical Terminology". The operating instructions contain instructions for the correction of possible malfunctions by the user in the section "Something not working". If these instructions should not be sufficient, please contact your local AEG Service Force Centre. Printed on paper manufactured with environmentally sound processes. he who thinks ecologically acts accordingly ... 2 818 1701-00/7 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Appliance Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The refrigerator needs ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appliance Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 9 10 10 11 Changing Over The Door Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Opening the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Appliance Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . View of Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Buttons for Adjusting the Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 15 16 16 17 Prior to Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Temperature Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 FAST CHILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Switching the Appliance Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bottle rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable Inner Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bottle Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 20 20 21 21 818 1701-00/7 3 Contents Correct storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 The refrigerator is defrosted automatically . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Hints and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Food Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Energy Saving Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replace light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 23 23 24 24 24 24 25 Something not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Guarantee Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 European Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 4 818 1701-00/7 1 Important Safety Instructions These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation · Check the refrigerator for transport damage. Under no circumstances should a damaged appliance be installed! In the event of damage, please contact your retailer. · · · Installation This appliance is heavy. Care should be taken when moving it. It is dangerous to alter the specifications or attempt to modify this product in any way. Ensure that the appliance does not stand on the electrical supply cable. If the supply cable is damaged, it must be replaced by a cable available from your local Service Force Centre. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Parts which heat up should not be exposed. Whenever possible, the back of the appliance should be close to a wall, but leaving the required distance for ventilation, as stated in the installation instructions. The appliance should be left for 4 hours after installation before it is turned on, in order to allow the refrigerant to settle. · · · Refrigerant The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable. · During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged. · If the refrigerant circuit should become damaged: ­ avoid open flames and sources of ignition; ­ thoroughly ventilate the room in which the appliance is situated. 818 1701-00/7 5 Important Safety Instructions Child Safety · Do not allow children to tamper with the controls or play with the product. · Keep packaging material away from children! (There is a risk of suffocation!) During Use · This appliance is designed for domestic use only, specifically for the storage of edible foodstuffs only. It is not intended for commercial or industrial use · Containers with flammable gases or liquids can leak at low temperatures. Do not store any containers with flammable materials such as, spray cans, fire extinguisher refill cartridges etc in the refrigerator. · Manufacturers´ recommended storage times should be adhered to. Refer to relevant instructions. Maintenance and Cleaning · Before cleaning, always switch off the appliance and disconnect from the electrical supply. · When unplugging always pull the plug from the mains socket, do not pull on the cable. Servicing · This product should be serviced by an authorised engineer and only genuine spare parts should be used. · Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local AEG Service Force Centre. 6 818 1701-00/7 Environmental Information Packaging All transit packaging materials are environmentally compatible and can be reused. Wood is un-treated. The plastics can be recycled and are identified as follows: >PE< for polyethylene, e.g. the outer covering and the bags in the interior. >PS< for polystyrene foam, e.g. the pads, which are pure hydrocarbon compounds and can be recycled. The carton parts are made from recycled paper. Please dispose of the packaging with due care for the environment. Old Appliances When disposing of your old appliance: Make the appliance unusable by cutting off the cable and remove any door catches to ensure small children cannot be trapped inside. Help to keep your country tidy - use an authorised disposal site. Appliance Transport Two persons are required for transport of the appliance. There are two recessed handles at the front of the base and at the back of the appliance at the top for improved gripping. 0 Grip the appliance with the recessed handles positioned as in the drawing, and transport the appliance. 818 1701-00/7 7 0 In order to push the appliance into its final position, press carefully at the top of the door and tip the appliance back slightly. The weight is thus transferred to the back casters and the appliance can be easily pushed. Before Use Packaging 0 Remove all adhesive tape and packaging from the interior of the appliance. 3 Any remnants of adhesive can be removed with white spirit. 0 Remove the transport protection pieces and pull off the adhesive tape. 0 Wash the inside of the appliance with lukewarm water with a little bicarbonate of soda added (5 ml to 0.5 litre of water). Do not use soap or detergent as the smell may linger. Dry the appliance thoroughly. 8 818 1701-00/7 Remove the transport fittings from the storage shelves: 0 Slide the fittings securing the shelf forward to the thicker section on the edge of the storage shelf. 0 Slide the storage shelf far enough forward so that it can be hinged downwards and the fittings can be removed from the guides. Installation Installation Location The appliance should be installed in a well ventilated, dry room. Energy use and efficient performance of the appliance is affected by the ambient temperature. The appliance should therefore ­ not be exposed to direct sunlight; ­ not be installed next to radiators, cookers or other sources of heat; ­ only be installed at a location whose ambient temperature corresponds to the climate classification, for which the appliance is designed. The climate classification can be found on the rating plate, which is located at the left on the inside of the appliance. The following table shows which ambient temperature is correct for each climate classification: Climate classification SN N ST T for an ambient temperature of +10 to +32 °C +16 to +32 °C +18 to +38 °C +18 to +43 °C 818 1701-00/7 9 Installation The refrigerator needs ventilation Air is fed under the door through the vent slots in the base and is exhausted upwards along the back wall. To ensure proper air circulation never cover or alter the vent openings. Important! If the appliance is installed under a hanging cabinet, a clearance of at least 10 cm between the top of the appliance and the cabinet above it must be maintained. Please check whether, after installing your appliance and especially after rehingeing the door, the door seal seals right round. An untight door seal may lead to heavy frosting and a higher power consumption (see also "Something not working"). Appliance Alignment 0 The appliance level please compensate for unevenness in the floor by turning the two adjustable feet at the front. 10 818 1701-00/7 Installation Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING ­ THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should these safety measures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is inside, on the left. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. Important The wires in the mains lead are coloured in accordance with the following code: Green Green and Yellow Earth & Yellow Blue Neutral Brown Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings indentifying the termiBrown Blue nals in your plug, proceed as follows: 1. The wire coloured green and yellow must be connected to Cord Clamp the terminal marked with the letter "E" or by the earth symbol or coloured green and yellow. 2. The wire coloured blue must be connected to the terminal "N" or coloured black. 3. The wire coloured brown must be connected to the terminal marked "L" or coloured red. 4. Upon completion there must be not cut, or stray strands of wire present and the cord clamp must be secure over the outer sheat. 1 Warning! A cut-off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut-off plug is disposed of safely. 11 818 1701-00/7 Changing Over The Door Hinges The door hinges can be changed from right (as supplied) to left if required to suit the location where the appliance is installed. Warning! Unplug from the mains, before reversing the door. 1 0 Open the door and remove the plinth to the front. Move the door bearing cover on the plinth from the left to the right. Close the door 0 With the door closed, remove the cross-head screws from the lower door bearing and remove the door bearing downwards. 0 Türbeschlag vom Türlager abnehmen (1, 2). Lagerzapfen von der rechten in die linke Bohrung umsetzen (3). Mitgelieferten Türbeschlag auf Lagerzapfen aufsetzen (4, 5). 12 818 1701-00/7 Changing Over The Door Hinges 0 Türbeschlag unten rechts aus der Tür herausnehmen (1). Türlagerabdeckung von links nach rechts umsetzen (2). Mitgelieferten Türbeschlag unten links in die Tür einsetzen (3). Tür vorsichtig nach vorne abnehmen und beiseite stellen. 0 Move the upper bearing pivot to the left. 0 Carefully slide the door onto the top bearing pivot and close. 0 Place the lower door bearing with the bearing pivot in the lower left of the door and fasten. 818 1701-00/7 13 0 Move the door handle from the left to the right and cover the remaining holes with the hole cover pins. 0 Open the door and fit the plinth. Opening the door If the door is closed when the appliance is in operation, it cannot be immediately opened again, because a vacuum occurs which holds the door closed until pressure has been equalised. The door can be opened again after several minutes. If your appliance is equipped with a QUICK door opener - an opening mechanism integrated into the door handle - the door can be opened easily at any time. 14 818 1701-00/7 Appliance Description View of Appliance (various models) Control panel Butter and cheese compartment with lid Door storage compartments Variable storage box Bottle compartment Fruit and vegetable drawers Shelves Bottle rack General purpose box Rating plate 818 1701-00/7 15 Appliance Description Control Panel 1 2 3 4 5 6 ON/OFF indicator light (green) ON/OFF button Temperature display Buttons for adjusting the temperature FAST CHILL indicator light (yellow) · FAST CHILL for intensive cooling in the refrigerator FAST CHILL button Buttons for Adjusting the Temperature The temperature is adjusted using the ,,+" (WARMER) and ,,-" (COLDER) buttons. These buttons are connected to the temperature display. · The temperature display is switched over from the display of the ACTUAL temperature (one light illuminated) to the display of the DESIRED temperature (one light flashing) by pressing one of the two buttons, ,,+" (WARMER) or ,,-" (COLDER). · With each further press of one of the two buttons, the DESIRED temperature is adjusted by one display field. · If neither button is pressed, the temperature display automatically switches back after a short period (approx. 5 sec.) to the display of the ACTUAL temperature. DESIRED temperature means: The temperature that is required in the freezer compartment, this can be adjusted to the temperatures shown in the display. The DESIRED temperature is indicated by a flashing light. ACTUAL temperature means: The temperature display indicates the temperature that is currently present in the freezer compartment. The ACTUAL temperature is indicated by a continuously illuminated light. 16 818 1701-00/7 Temperature Display The temperature display can indicate several pieces of information. · During normal operation, the temperature currently present in the refrigerator (ACTUAL temperature) is displayed, the corresponding light illuminates. · If the temperature in the refrigerator is warmer than the display range of the temperature display, all the lights in the temperature display are extinguished. · If the temperature in the refrigerator is colder than the display range of the temperature display, then the light for the lowest temperature (+2) continues to illuminate. · When the temperature is being adjusted, the temperature currently set flashes (DESIRED temperature). · If there is a malfunction in the appliance that prevents the temperature from being further measured, all the lights on the temperature display flash. Prior to Initial Start-Up 1 Before connecting the appliance to the mains and putting it into operation for the first time, leave the appliance to stand for 30 minutes if was transported upright. After transport on its side, the appliance must be left to stand for 4 hours before putting it into operation. This is necessary to allow the oil to flow back into the compressor. Otherwise the compressor may be damaged. 0 Please clean the appliance interior and all accessories prior to initial start-up (see section: "Maintenance and Cleaning"). 818 1701-00/7 17 Initial Start-Up 0 Insert plug into mains socket. 0 Press ON/OFF button. The green power indicator lights up. 0 Set the refrigerator to the desired temperature (see section: "Temperature Adjustment"). 3 Goods to be refrigerated can be loaded immediately after switching on, because the storage temperature in the refrigerator is quickly reached. Temperature Adjustment With the buttons for temperature adjustment the desired temperatures in the refrigerator can be adjusted. 0 Press either the ,,+" (WARMER) or ,,-" (COLDER) button. The temperature display switches over and the DESIRED temperature currently set flashes on the temperature display. 0 To adjust to a warmer temperature, press the ,,+" button. To adjust to a colder temperature, press the ,,-" button. The changed setting is immediately displayed on the temperature display. The temperature is adjusted by one display field with each press of a button. Note: From a food science point of view, +5 °C for the refrigerator compartment should be considered cold enough as a storage temperature. 3 When the buttons are not further pressed after an adjustment has been made, after a short period (approx. 5 sec.) the temperature display switches over and again displays the ACTUAL temperature in the refrigerator. The display changes from flashing to continuous illumination. 18 818 1701-00/7 FAST CHILL The FAST CHILL function is suited for quick cooling of large quantities of goods in the refrigerator, e.g. drinks and salads for a party. 0 The FAST CHILL function is switched on by pressing the FAST CHILL button. The yellow light illuminates. The FAST CHILL function now provides for intensive cooling. A DESIRED temperature of +2¯C is automatically selected. The FAST CHILL function is ended automatically after a period of 6 hours. The originally selected DESIRED temperature is again valid. The temperature display shows the ACTUAL refrigerator temperature. 0 The FAST CHILL function can be ended manually at any time by pressing the FAST CHILL button again. The yellow light goes out. Switching the Appliance Off 0 To switch off, press the ON/OFF button until the mains power light extinguishes. Note: The appliance cannot be switched on or off if unplugged, or if there is no power being supplied to it. Following connection to the mains power supply, the appliance returns to the same operating state as before the interruption of main power. 0 0 0 0 If the appliance is to be removed from service for a lengthy period: Switch off the appliance, to do this press the ON/OFF button until the mains power light extinguishes. Remove the mains plug or switch off. Clean the appliance thoroughly (see section: "Maintenance and Cleaning"). Leave door open to avoid accumulation of odours. 818 1701-00/7 19 Interior Accessories Storage Shelves 0 A storage shelf must be inserted into the lower guide track above the fruit and vegetable trays. It must always remain in this position, so that fruits and vegetables remain fresh longer. The remaining storage shelves can be adjusted to various heights: 0 Pull the storage shelf forward until it can be tipped up or down and removed. 0 To insert at a different height use the same procedure in reverse. Adjustment for tall items: 0 Remove the front half of the twopart vario glass storage shelf and insert it at a different level. Space is then gained for storage of tall items on the storage shelf below. Bottle rack Place bottles in the rack with the bottleneck to the front. Important: Only store unopened bottles horizontally. The bottle rack can be tilted for storing opened bottles. 20 818 1701-00/7 Interior Accessories 0 To do this pull the bottle rack forward until it can be tilted upwards, then slide the front support into the next level up. Variable Inner Door The door compartments can be pulled up and removed, and inserted at other positions as needed. Bottle Holder (not included with all models) Some models are equipped with a bottle holder in the bottle compartment. This is used to prevent individual bottles from falling over and can be slid sideways. 818 1701-00/7 21 Correct storage For physical reasons, the refrigerator compartment has different temperature zones. The coldest zone is on the lowest storage shelf immediately above the fruit and vegetable trays. Warmer zones are the upper storage shelves and door racks. The arrangement (see fig.) indicates where different types of food are best stored to make the most of temperature variations. For instance, the shelf immediately above the fruit and vegetable trays should be 5 °C for safe storage of meat and fish products. In order to check that the appliance is at 5 °C on the lowest shelf you can carry out the following test yourself: 0 Place a cup of water in the center of the said shelf with a thermometer inside. 0 Leave the fridge door closed overnight and check the temperature first thing in the morning. 0 At this point the temperature should read no more than 5 °C; if it does, you need to adjust the temperature to a colder setting. For further information on keeping food cool and safe a guide published by the Ministry of Agriculture, Fisheries and Food is available and can be obtained free of charge by contacting: Foodsense, London SE99 7TT. Tel: 0645 556000 Tip: Food stored in the refrigerator compartment should always be covered or packed so that they do not dry out, lose their flavour, or transfer their flavour to any other refrigerated food. The following are suitable for packing: ­ polyethylene bags; ­ plastic containers with lids; ­ special plastic covers with rubber retainers; ­ aluminium foil. 22 818 1701-00/7 Defrosting The refrigerator is defrosted automatically The electronics start the defrosting cycle in the refrigerator every time the compressor stops. The water collects in the discharge trough at the back wall of the refrigerator, and is fed through the discharge opening in the catch tray at the compressor where it is evaporated. Hints and Tips Normal Operating Sounds · You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils or tubing at the rear, to the cooling plate/evaporator. · When the compressor is on, the refrigerant is being pumped round and you will hear a whirring sound or pulsating noise from the compressor. · A thermostat controls the compressor and you will hear a faint click when the thermostat cuts in and out. Food Storage To obtain the best performance from your refrigerator: · Do not store warm food or evaporating liquids. · Do not store food uncovered. · Do not push food together too much, try to allow air to circulate around each item. 818 1701-00/7 23 2 Energy Saving Advice · Do not install the appliance close to sources of heat, such as a cooker, dishwasher or radiator. · Locate the appliance in a cool well ventilated room and make sure that the air openings of the appliance are not obstructed. · Always leave warm food to cool down to room temperature before placing in the refrigerator. · Try to avoid keeping the door open for long periods or opening the door too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often. · Ensure there are no obstructions preventing the door from closing properly. Maintenance and Cleaning Before any maintenance or cleaning work is carried out DISCONNECT the appliance from the ELECTRICITY supply. Internal Cleaning 0 Clean the inside and accessories with warm water and bicarbonate of soda (5 ml to 0.5 litre of water). Rinse and dry thoroughly. 1 Warning! · Do not use detergents, abrasive powders, highly perfumed cleaning products, wax polishes or cleaning products containing bleach or alcohol. 0 Regularly check the door seals and wipe clean to ensure they are clean and free from debris. External Cleaning 0 Wash the outer cabinet with warm soapy water. 1 Warning! · Do not use abrasive products · There are sharp edges on the underside of the product so care should be taken when cleaning. Accumulation of dust at the condenser increases energy consumption. For this reason carefully clean the condenser at the back of the appliance once a year with a soft brush or a vacuum cleaner. 818 1701-00/7 2 24 Maintenance and Cleaning Replace light bulb 3 1 For safety reasons the interior lighting switches off after 20 minutes when the door is open. It switches on again the next time the door is opened. Warning! Danger of electrical shock! Before replacing the light bulb switch off the appliance and remove the mains plug. Light bulb specifications: 220-240 V, max. 25 W, fitting: E 14 Important! When replacing the lamp only fit a lamp of suitable diameter, that is at least 18 mm, this will ensure a good seat on the rubber seal. Where to purchase: specialist retailer or AEG customer service. 0 To switch the appliance off press the ON/OFF button until the mains power light extinguishes. 0 Unplug the mains plug. 0 To change the light bulb, undo the cross head screw and remove the light bulb cover downwards. 0 Change the defective light bulb. 0 Refit the light bulb cover and the cross head screw. 818 1701-00/7 25 Something not Working Before contacting your local service force centre, check the following points. Symptom Solution Check there is power at the socket No power to the appliance. Check there is not a power cut by checking the household lights. Check the fuse has not blown. Check the ambient temperature is within the appliances operating limits The temperature in the refrigerator is too Check the temperature adjustment is turhigh. ned to the correct setting relative to ambient conditions. Interior illumination does not function. Important: The interior lighting switches off automatically after 20 minutes. Please refer to "Replace Light Bulb " section. Adjust the thermostat to give correct temperature control. Check that the door is closed. The compressor runs continuously Large quantities of food have recently been placed in the cabinet and/or door is frequently opened. Check that air ventilation is not obstructed. If the door seal is not airtight (probably after changing over the door hinges) apply warm air to the non sealing area using a hair dryer set to a gentle heat. (do not use a fan heater for this purpose). This will make the rubber more supple and allow it to revert to its original shape. Refer to Normal Operating Sounds This is normal, the compressor starts after a period of time. Excessive build up of frost. Noise The compressor does not start immediately after changing the temperature setting. 26 818 1701-00/7 Something not Working If after the above checks there is still a fault, call your local AEG Service Force Centre. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for in-guarantee service calls. 818 1701-00/7 27 Technical Terminology · Refrigerant Liquids that can be used to a generate a cooling effect are known as refrigerants. They have a relatively low boiling-point, indeed so low, that the warmth from the food stored in the fridge or freezer can cause the refrigerant to boil and vaporise. · Refrigerant Circuit Closed circulation system that contains the refrigerant. The refrigerant circuit comprises primarily of an evaporator, a compressor, a condenser and pipe work. · Evaporator The refrigerant is evaporated in the evaporator. Similar to all other liquids, refrigerant requires heat to evaporate. This heat is removed from the interior of the appliance, as a result the interior is cooled. The evaporator is therefore located inside the appliance or placed in foam immediately behind the inner wall and thus not visible. · Compressor The compressor looks like a small drum. It is driven by a built-in electric motor and is mounted on the base of the appliance at the rear. The task of the compressor is to draw in vaporised refrigerant from the evaporator, to compress it, and to pass it on to the condenser. · Condenser The condenser normally has the form of a grid. The refrigerant compressed in the compressor is liquefied in the condenser. During this process, heat is released to the surrounding air at the surface of the condenser. The condenser is mounted on the base of the appliance. Regulations, Standards, Guidelines This appliance was designed for household use and was manufactured in accordance with the appropriate standards. The necessary measures in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and the regulations of the German Society of Electrical Engineers (VDE) were observed in the manufacture of this appliance. The refrigerant circuit has been checked for leaks. ; This appliance is in accordance with the following EU guidelines: ­ 73/23/EWG dated 19 February 1973 - low voltage guidelines. ­ 89/336/EWG dated 3 May 1989 (including guideline change notice 92/31/EWG) - EMV guideline 818 1701-00/7 28 Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials. The guarantee does not cover appliances where defects or poor performance are due to misuse, accidental damage, neglect, faulty installation,unauthorised modification or attempted repair, commercial use or failure to observe requirements and recommendations set out in the instruction book. This guarantee does not cover such parts as light bulbs, removable glassware, dust bags or filters. 3. Should guarantee repairs be necessary the purchaser must inform the nearest customer service office (manufacturer´s service or authorised agent). AEG reserves the right to stipulate the place of the repair (i. e. the customer´s home, place of installation or AEG workshop). 4. The guarantee or free replacement includes both labour and materials. 5. Repairs carried out under guarantee do not extend the guarantee period for the appliance. Parts removed during guarantee repairs become the property of AEG. 6. The purchaser´s statutory rights are not affected by this guarantee. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: ­ The guarantee starts from the date you first purchased your product. ­ The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products. ­ This guarantee relates to you and connot be transferred to another user. ­ Your new home is within the European Community (EC) or European Free Trade Area. ­ The product is installed and used in accordance with our instructions and is only used domestically, i. e. a normal household. ­ The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nürnberg Pordenone Stockholm Slough +33 (0) 44 62 29 29 +49 (0) 911 323 2600 +39 (0) 1678 47053 +46 (0) 8 738 7910 +44 (0) 1753 219899 818 1701-00/7 29 30 818 1701-00/7 Service & Spare Parts If after carrying out the necessary checks there is still a fault with your appliance please contact your local AEG Service Force Centre. In guarantee customers should ensure that the suggested checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for in-guarantee service calls. Service & Spare Parts If you require a service engineer or wish to purchase spare parts, contact your local AEG Service Force Centre, by telephoning 08705 929 929 Help us to help you Please determine your type of enquiry before writing or telephoning. When you contact us we need to know, 1 Your name, address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 Date of purchase 5 · Model Name · Model Number (PNC) · Serial Number (S-No.) This information can be found on the rating plate in the interior of the appliance at the left. Customer Care For general enquiries concerning your AEG appliance, or for further information on AEG products, you are invited to contact our Customer Care Department by letter or telephone: AEG Domestic Appliances Limited 55-77 High Street Slough Berkshire SL 1 1DZ Tel: 08705 350350 818 1701-00/7 31 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Copyright by AEG 818 1701 ­ 00/7 - 0400