TVG18H TVG18H ---------------------------------------------------------------------------------------------------------------------Désignation Code Rérérence ! V795VHRL5000482 PIANO AIRLUX TVG18H FRANCIA NR 1,000 ! ---------------------------------------------------------------------------------------------------------------------! 001 Z003051 BURNER MICRO UNIT NR 4 ! ! 003 Z004013 IGNITION GENERATOR NR 1 ! ! 004 Z005005 TRIPOLAR MICRO UNIT NR 1 ! ! 005 Z101205 GAS RAMP NR 1 ! ! 006 Z002005 SPARK IGNITION L.250 DEF3 NR 1 ! ! 006 Z002006 SPARK IGNITION L.400 DEF3 NR 2 ! ! 006 Z002009 SPARK IGNITION L.500 NR 1 ! ! 009 Z002016 SPARK IGNITION L.540 ISPH. NR 1 ! ! 010 Z102515 WOK BURNER PIPE OUTER NR 1 ! ! 010 Z102516 WOK BURNER PIPE INNER NR 1 ! ! 050 Z103500 A BURNER BOWL 77 G20 DEF3 NR 1 ! ! 051 Z103501 SR BURNER BOWL 97 G20 DEF3 NR 2 ! ! 052 Z103502 R BURNER BOWL 129 G20 DEF3 NR 1 ! ! 054 Z103093 WOK BURNER G25-25 NR 1 ! ! 060 Z103408 A BURNER HEAD NR 1 ! ! 061 Z103409 SR BURNER HEAD NR 2 ! ! 062 Z103410 R BURNER HEAD NR 1 ! ! 064 Z104011 OUTSIDE BURNER ISPH. CROWN NR 1 ! ! 065 Z104010 CENTRAL BURNER ISPH. CROWN NR 1 ! ! 066 Z104013 OUTSIDE BAFFLE PLATE NR 1 ! ! 067 Z104012 CENTRAL BAFFLE PLATE NR 1 ! ! 070 Z105020 A BURNER COVER NR 1 ! ! 071 Z105021 SR BURNER COVER NR 2 ! ! 072 Z105022 R BURNER COVER NR 1 ! ! 080 Z106043 BY-PASS TAP 27 NR 1 ! ! 081 Z106044 BY-PASS TAP 29 NR 2 ! ! 082 Z106045 BY-PASS TAP 40 NR 1 ! ! 091 Z106047 BY PASS DOUBLE TAP 63+25 NR 1 ! ! 110 Z107013 THERMOCOUPLE L.500 NR 2 ! ! 110 Z107022 THERMOCOUPLE L.250 NR 2 ! ! 112 Z107030 THERMOCOUPLE L.380 ISPH. NR 1 ! ! 120 Z200031 VTC PLATFORM NR 1 ! ! 130 Z202052 INOX KNOB NR 4 ! ! 130 Z202054 INOX KNOB NR 1 ! ! 139 Z203118 WOK REDUCTION CAST IRON NR 1 ! ! 141 Z203115 A/SR BURNER CAST IRON RACK NR 3 ! ! 142 Z203116 R BURNER CAST IRON RACK NR 1 ! ! 143 Z203117 WOK BURNER CAST IRON RACK NR 1 ! ! 150 Z204033 A/SR SUMP WASHER NR 3 ! ! 152 Z204035 WOK SUMP WASHER NR 1 ! ! 153 Z204034 R SUMP WASHER NR 1 ! ! 155 Z204029 KNOB WATER SEAL BUSH VTC NR 5 ! ! 160 Z204006 RUBBER-HOSE HOLDER WASHER NR 2 ! ! 162 Z307004 GAS ELBOW (1/2") NR 1 ! ! 170 Z308008 FIX TOP HOOK NR 4 ! ! 173 Z621088 FIXING BRACKET FOR A-SR-R BURNER NR 2 ! ! 174 Z621089 FIXING BRACKET FOR WOK BURNER V79 NR 1 ! ! 175 Z621086 TOP BOTTOM NR 1 ! ! 180 Z711030 A CAST IRON SUMP NR 1 ! ! 181 Z711031 SR CAST IRON SUMP NR 2 ! ! 182 Z711032 R CAST IRON SUMP NR 1 ! ---------------------------------------------------------------------------------------------------------------------- ---------------------------------------------------------------------------------------------------------------------Désignation Code Référence ! V795VHRL5000482 PIANO AIRLUX TVG18H FRANCIA NR 1,000 ! ---------------------------------------------------------------------------------------------------------------------! 186 Z711033 WOK CAST IRON SUMP NR 1 ! ! 187 Z711034 WOK RING CAST IRON NR 1 ! ! 300 Z106208 NOZZLE ISPH. 0.46 (X) G20-20 NR 1 ! ! 300 Z106209 NOZZLE ISPH. 0.37(G) G30-30 NR 1 ! ! 300 Z106210 UGELLO ISPH.DC 1,09 G30-30 NR 1 ! ! 300 Z106214 NOZZLE ISPH.DC 1.70 G20-20 NR 1 ! ! 430 Z102511 A BURNER PIPE NR 1 ! ! 431 Z102513 R BURNER PIPE NR 1 ! ! 432 Z102514 SR BURNER PIPE LEFT NR 1 ! ! 433 Z102512 SR BURNER PIPE RIGHT NR 1 ! ---------------------------------------------------------------------------------------------------------------------- INSTRUCTIONS FOR THE INSTALLATION AND USE OF CERAMIC GAS COOK-TOPS INSTRUCTIONS POUR L'INSTALLATION ET L'UTILISATION DES TABLES DE CUISSON VITROCERAMIQUE AU GAZ La nouvelle Cuisine TDVG7H TVG16H TVG18H Dear Customer, We thank you and congratulate you on granting us your preference, by purchasing one of our products. We are sure that this new appliance, manufactured with quality materials, will meet your requirements in the best possible way. The use of this new equipment is easy. However, we invite you to read this booklet carefully, before installing and using the appliance. This booklet gives the right information on the installation, use and maintenance, as well as useful advice. THE MANUFACTURER GENERAL NOTICE We invite you to read this instruction booklet carefully, before installing and using the equipment. It is very important that you keep this booklet together with the equipment for any future consultation. If this equipment should be sold or transferred to another person, make sure that the new user receives the booklet, so that he can learn how to operate the appliance and read the corresponding notice. · The installation must be carried out by experienced and qualified personnel, in conformity with the regulations in force. · This equipment has been designed to be used by adults. · Therefore, make sure that children do not go near the equipment to play with it. · While the appliance is running, watch the children and make sure they neither stay near the equipment, nor touch the surfaces that have not cooled down completely. · Before powering the equipment, check that it is properly adjusted for the type of gas at disposal (see the "installation" paragraph). · Before carrying out the maintenance or cleaning the equipment, cut power supply off and make it cool down. · Make sure that air circulates around the gas equipment. Insufficient ventilation produces a lack of oxygen. · In case of an intense or prolonged use of the equipment, it may be necessary to improve aeration, for example by opening a window or increasing the mechanical suction power, if it exists. · The products of combustion must be discharged outside through a suction hood or an electric fan (see the "installation" paragraph). · For any possible operation or modification, apply to an authorized Technical Assistance Centre and demand original spare parts. The manufacturer refuses all responsibility for possible damages to things or people, resulting from a wrong installation or from an improper, incorrect or unreasonable use of this equipment. This product complies with EU Directive 2002/96/EC. The crossed-out dustbin symbol reported on the appliance indicates that the appliance must be disposed of separately from other domestic refuse at the end of its useful life. It must therefore be delivered to a waste recycling centre specifically for electric and electronic equipment or returned to the retailer at the moment of purchase of a new equivalent appliance. The user is responsible for delivering the appliance to the appropriate collection centre at the end of its useful life, Failure to do so may result in a fine, as provided for by laws governing waste disposal. Differential collection of waste products for eventual recycling, treatment and environmentally friendly disposal helps reduce possible negative effects on the environment and health, and also enables the materials making up the product to be recycled. For more detailed information on the available refuse collection systems, refer to the local Municipal Solid Waste disposal centre or the shop where the product was purchased. Producers and importers are responsible for fulfilling their obligations as regards recycling, treatment and environmentally friendly disposal by directly or indirectly participating in the collection system. The manufacturing firm refuses all responsibility for any possible imprecision in this booklet, due to misprints or clerical errors. It reserves the right to make all the changes that it will consider necessary in its own products, without affecting the essential characteristics of functionality and safety. IT IS NECESSARY THAT ALL THE OPERATIONS REGARDING THE INSTALLATION, ADJUSTMENT AND ADAPTATION TO THE TYPE OF GAS AVAILABLE ARE CARRIED OUT BY QUALIFIED PERSONNEL IN CONFORMITY WITH THE REGULATIONS IN FORCE. THE SPECIFIC INSTRUCTIONS ARE DESCRIBED IN THE BOOKLET SECTION INTENDED FOR THE INSTALLER USING THE BURNERS The symbols silk-screen printed on the side of the knob indicate the correspondence between the knob and the burner. Automatic start-up with valves Turn the corresponding knob anticlockwise up to position required, between the high and low settings. Press the knob. Once the burner has been started up, keep the knob pressed for about 5 seconds (fig.1 ­ fig.1/A). Using the burners In order to obtain the maximum yield without waste of gas, it is important that the diameter of the pot is suitable for the burner potential (see the following table), so as to avoid that the flame goes out of the pot bottom (fig.2). Use the maximum capacity to quickly make the liquids reach the boiling temperature, and the reduced capacity to heat food or maintain boiling. All of the operating positions must be chosen between the maximum and the minimum ones, never between the minimum position and the closing point. The gas supply can be interrupted by turning the knob clockwise up to the closing position. If there is no power supply, it is possible to light the burners with matches, setting the knob to the start-up point (large flame). Burners Auxiliary Semi-rapid Rapid Double-ring Power W 1000 1650 3000 5500 Ø of pots 10-14 cm 16-18 cm 20-22 cm 24-26 cm Notice - When the equipment is not working, always check that the knobs are in the closing position (see fig.1 ­ fig. 1/A). - If the flame should blow out accidentally, the safety valve will automatically stop the gas supply, after a few seconds. To restore operation, set the knob to the lighting point (large flame, fig.1 ­ fig. 1/A). - While cooking with fat or oil, pay the utmost attention as these substances can catch fire when overheated. - Do not use sprays near the appliance in operation. - Do not place unstable or deformed pots on the burner, so as to prevent them from overturning or overflowing. - Make sure that pot handles are placed properly. - When the burner is started up, check that the flame is regular and, before taking pots away, always lower the flame or put it out. CLEANING Before any operation, disconnect the appliance from the electric grid. It is advisable to clean the appliance when it is cold. Glass platform and enamelled parts The glass platform and all of the enamelled parts must be washed with a sponge and soapy water or with a light detergent. Do not use abrasive or corrosive products. Do not leave substances, such as lemon or tomato juice, salt water, vinegar, coffee and milk on the enamelled surfaces for a long time. Burners and racks These parts can be removed to make cleaning easier. The burners must be washed with a sponge and soapy water or with a light detergent, wiped well and placed in their housing perfectly. Make sure that the flame-dividing ducts are not clogged. Check that the feeler of the safety valve and the start-up electrode are always perfectly cleaned, so as to ensure an optimum operation. The racks can be washed in the dishwasher. Gas taps The possible lubrication of the taps must be carried out by specialized personnel, exclusively. In case of hardening or malfunctions in the gas taps, apply to the Customer Service. IMPORTANT NOTICE THE OPERATIONS INDICATED BELOW MUST BE FOLLOWED BY QUALIFIED PERSONNEL EXCLUSIVELY, IN CONFORMITY WITH THE REGULATIONS IN FORCE. THE MANUFACTURING FIRM REFUSES ALL RESPONSIBILITY FOR DAMAGES TO PEOPLE, ANIMALS OR THINGS, RESULTING FROM THE FAILURE TO COMPLY WITH SUCH PROVISIONS. INSTALLATION Installing the top The appliance is designed to be embedded into heat-resistant pieces of furniture. The walls of the pieces of furniture must resist a temperature of 65°C besides the room one. The equipment must not be installed near inflammable materials, such as curtains, cloths, etc. Make a hole in the top of the piece of furniture, with the dimensions indicated in fig. 3 and in fig. 4, at a distance of at least 50 mm from the appliance border to the adjacent walls. Any possible wall unit over the cook-top must be placed at a distance of at least 760 mm from the top. APPLIANCE 900x520 800x520 600x520 290X520 L (mm) 860 750 560 275 P (mm) 490 490 490 490 Fastening the top Every cook-top is equipped with a special washer having an adhesive side. - Remove the racks and burners from the top. - Turn the appliance upside down and lay the adhesive washer S along the external border of the glass (fig.5). - Introduce and place the cook-top in the hole made in the piece of furniture, then block it with the screws of the fastening hooks C (fig.6). Installation room This appliance is not provided with a device for exhausting the products of combustion. Therefore, it is necessary to discharge these smokes outside. The room where this appliance is installed must have a natural air inflow, 3 so as to ensure a regular gas combustion and room ventilation: the necessary air volume must not be lower than 20 m . Air must come from permanent openings made on the room walls that communicate with the outside. The section of these openings shall correspond to at least 200 cm². Gas connection Make sure that the appliance is adjus ...