User manual AKAI LCT2701TD

Safety Guidelines Caution: Always use a power cable is properly grounded. Please use the AC cords listed below for each area: USA ...................... UL Canada ................ CSA/cUL FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. FCC Warning To assure continued FCC compliance, the user must the provided grounded power supply cord and the provided shielded video interface cables to connect to this equipment. Also, any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. Labels A. CLASSIFICATION LABEL B. WARNING LABEL CLASS 1 LASER PRODUCT 1. CLASS 1 LASER PRODUCT 2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover or remove screws. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel. Do not insert any metallic object into the System. 1 IMPORTANT SAFEGUARDS Important Safeguards Before using your TV, please read these instructions completely, and keep this manual for future reference. Carefully observe and comply with all warnings, cautions and instructions placed on the unit or described in the operating instructions or service manual. The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties: WARNING ----- Ignorance or inappropriate use may cause damage to the product. ATTENTION --- Ignorance or inappropriate use may cause injury to the user. Examples: Prohibition Warning (Attention) symbol (indicating "Electric Shock"). WARNING Never place TV on an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV. Never overload wall outlets and extension cords. Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse. Keep the product away from moisture: - Do not expose this appliance to rain or moisture. - If water penetrates into the product, stop the operation; unplug the connector and contact with your dealer. Continuous use in this case may result in fire or electric shock. WARNING Never place item such as vases, aquariums, or candles on top of the TV. 2 Never use a damaged power cord: Heavy objects, heat, or tensile force may damage the power cord and cause fire or electric shock. Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV: - on a bed, sofa, rug, or similar surface; - too close to drapes, curtains, or walls; or - in a confined space such as bookcase, built-in cabinet, or any other place with poor ventilation. The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV. Do not use the product if any abnormality occurs: If any smoke or odor becomes apparent, unplug the connector and contact the manufacturer immediately. Do not try to repair the product by yourself. WARNING Avoid using dropped or damaged appliances: If the product is dropped and the housing is damaged, the internal components may function abnormally. Unplug the connector immediately and contact the manufacturer for repair. Continuous use of the product may cause fire or electric shock. WARNING While it is thundering, do not touch the connecting cables or apparatus. ATTENTION Do not install the product close to smoke or moisture: Fire or electric shock may be caused when the product is installed close to smoke or moisture. Do not installed the product in an area with heavy dust or high humidity: Fire or electric shock may be caused when the product is installed in a place with heavy dust or high humidity. Instructions for moving the product: Ensure that the power connector and any other leads are unplugged before moving the product. 3 IMPORTANT SAFEGUARDS The power cable should be kept away from heat sources: The heat produced by any heat source may melt the covering of the power cable. Unplug the connector Hold the power connector when removing the power cable: Pulling the power cable itself may damage the wires inside the cable and cause fire or electric shock. Do not touch the connector with wet hands: To avoid risk of electric shock. ATTENTION Insert batteries in accordance with instructions: Insert the batteries with correct polarities (positive and negative ). Incorrect polarities may cause breakage and leakage of the batteries, hurt operators and contaminate the remote controller. Do not block or cover the vents: Blocking the vents may cause overheating and fire. Do not install the product in a place with little or no ventilation. Never cover the vents with towels, blankets or dusters. Unplug the connector: Unplug the power connector when the product will not be used for a long time. Unplug the connector Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges.(see Section 810 of the National Electric Code.) Antenna lead-in wire Antenna discharge unit (NEC Section 810-20) Ground clamp Electric service equipment Grounding conductors (NEC Section 810-21) Power service grounding electrode system (NEC Art 250 Part H) Ground clamp Use extreme care to make sure you are never in a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits. Never attempt to install any of the following during lightning activity: a). an antenna system; or b).cables, wires, or any home theater component connected to an antenna or phone system. 4 The LCD panel on this TV is manufactured using an extremely high level of precision technology; however, an occasional pixel (dot of light) may display constantly on the screen. This is a structural property of LCD technology and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance. LCD (Liquid Crystal Display) may cause interference in image, sound, etc.of the other electronic equipment that is easy to receive electromagnetic waves (i.e. AM radios and video equipment) under certain installed condition. In particular, it may affect electronic equipment beyond the residential until where a LCD TV is used. The screen on this TV is manufactured from glass. To prevent damage, never strike the glass with a sharp or heavy object. Your LCD television contains a small amount of Mercury. When the television is no longer useful, please follow local electronic waste guidelines for proper disposal. If you have the LCD screen facing to the sun, the LCD screen will be damaged. Locate the TV in the place such away from windows side or out side of the rooms with windows. This product is designed for indoor use only. The operation temperature are 5°C ~ 30°C. On handling discs Do not touch the playback side of the disc. Playback side Do not attach paper or tape to discs. On cleaning discs Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean. Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc. On storing discs Do not store discs in a place subject to direct sunlight or near heat source. Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping. 5 IMPORTANT SAFEGUARDS Notes on region numbers CONTENTS 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. The apparatus shall not be exposed to dripping or splashing and that no objected filled with liquids, such as vase, shall be placed on the apparatus. This DVD player is designed and manufactured for playback of region "1" encoded DVD software. The region code on the labels of some DVD discs indicates which type of player can play those discs. This unit can play only DVD discs labeled "1" or "ALL". If you try to play any other discs, the message "Check Regional Code" will appear on the TV screen. Some DVD discs may not have a region code label even though their playback is prohibited by area limits. Precaution Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that product heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 1. 2. 3. 4. 5. 6. 7. 6 Contents Safety Guidelines .........................................1 Important Safeguards ..................................2 1. Before use ...............................................8 2. Product Features ......................................8 Open the Package ......................................... 8 Installation .................................................... 8 Using "Contrast"................................... 29 Using "Brightness" ................................ 30 Using "Back Light" ................................ 30 Using "Auto Setting" .............................. 30 Using "Phase" ...................................... 30 Using "Manual Clock" .......................... 31 Using "Display Adjustment" ................... 31 DVD Operations ...................................... 32 Basic Playback ...................................... 32 Stop Playback ....................................... 32 Pause Playback ..................................... 32 Fast Forward/Backward ......................... 32 Skip a Chapter or a Track ...................... 32 OSD(On-Screen Display) ....................... 32 Selecting the disc menu ......................... 33 Repeat playback ................................... 33 Programmed Playback .......................... 33 Audio ................................................... 33 Audio CD Playback options ...................... 33 OSD(On-Screen Display) ....................... 33 Stop Playback ....................................... 33 Pause Playback ..................................... 33 Fast Forward/Backward ......................... 33 Repeat playback ................................... 34 DVD Menu options ................................... 34 TV Display ............................................ 34 Selecting camera angles........................ 34 Disc OSD Language Selection ............... 34 Digital Auido Output ............................. 34 Screen Saver ......................................... 34 Last Scene Memory ............................... 35 Selection of Down Mix .......................... 35 Selection of Dual Mono ......................... 35 Selection of Dynamic ............................ 35 Selecting an Audio Language ................ 35 Selecting a subtitle language ................. 35 Disc menu language selection ............... 36 Parental Control Setup .......................... 36 Changing the password ........................ 36 Default ................................................. 36 3. Names and Functions of Parts...................9 Side View ...................................................... 9 Front View ..................................................... 9 Rear View ...................................................... 10 Remote Control ............................................. 11 4. Connect Accessory Devices .......................13 5. Basic Operation .......................................16 Power ON/OFF ............................................. 16 Selection of Input Mode ................................. 16 Other Function .............................................. 16 OSD Option Adjustment ................................ 17 TV Operations ............................................... 18 Using the Video Menu .............................. 18 Adjustment of "Contrast" ....................... 18 Adjustment of "Brightness" .................... 18 Adjustment of "Back Light" .................... 18 Adjustment of "Saturation" .................... 19 Adjustment of "Hue" ............................. 19 Adjustment of "Sharpness" .................... 19 Selection of "Phase" setting .................. 19 Selection of "Color Temperature" ........... 20 Selection of "Advance Picture Adjust"...... 20 Using the Audio Menu .............................. 21 Adjustment of "Bass" ............................. 21 Adjustment of "Treble" .......................... 21 Adjustment of "Balance"........................ 21 Selection of "Surround" ......................... 22 Using the Miscellaneous Menu .................. 22 Selection of "Language" ........................ 22 Selection of "Closed Caption" ............... 22 Setting of "V-Chip" ............................... 23 Setting of "Parental" .............................. 26 Selection of "Blue Mute" ........................ 27 Using "Default" .................................... 27 Using the TV Menu ................................... 28 Using the "Auto Search" ........................ 28 Using the "Tuner Mode" ........................ 28 Using the "Channel Skip" ...................... 28 Using the "Channel Name" ................... 28 Selecting Channel ................................. 29 Channel Preview ................................... 29 Using the Geometric Menu ....................... 29 6. Technical Specification .............................37 7. Supplied Accessories ................................37 8. Support the Signal Mode ..........................38 9. Cleaning and Simple Troubleshooting .......38 7 BEFORE USE PRODUCT FEATURES SIDE VIEW FRONTE VIEW 1. Before use The product is a 27" WXGA (WXGA resolution) LCD TV/DVD Player Combo. It has passed the UL and cUL safety certifications, and is an ideal product for personal and commercial use. The product is a precise electronic product. Users should read the following instructions carefully to maximize the performance and life span of the product: Open the Package - The product is packaged in a carton together with other standard accessories. Any optional accessories shall be packed separately in another carton. - Due to the size & weight of the product, it is recommended that it should be moved by a minimum of two people. - The protective glass and the glass substrate are installed on the front of the product. Since both glasses can be broken and scraped easily, move the product gently. Never place the unit with the glass facing downwards unless it is protected with soft pads. - When opening the carton, check that the product is in good condition and that all standard accessories and items are included. - Whenever possible, use the handles on the back of the Display for transport. Installation - Please use caution if wall mounting this product. Follow all directions from the manufacturer of the wall mount and be sure to securely fasten the product to the mount. While the TV can be wall mounted, improper wall installation may void the warranty. - Due to the higher power consumption, always use the jack exclusively designed for this product. If an extended line is required, please consult with your service agent. - The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained for proper ventilation. - Avoid installing the product in the kitchen, bathroom or any other places with higher humidity so as not to shorten the service life of the electronic components. - Please ensure the product be installed horizontally, any 90 degree clockwise or counterclockwise installation may induce poor ventilation and subsequent component damage. - To protect the screen and avoid screen burn, do not hold on a static picture for a long time. 2. Product Features The 27 LCD TV/DVD Player Combo provides quality image displays and is suitable for a variety of multi media applications: 1. Available input signals - The standard PC module provides VGA (D-SUB 15 PIN), and a RS-232 (D-SUB 9 PIN MALE) communication connector. The product supports PC mode image resolutions up to (1024 x 768@60Hz) with a vertical frequency of 60 Hz. (The VGA input may not be supported some of the PC Display Card.) - The Video module provides composite video (RCA), S-video (DIN 4 PIN) and component video (RCA) input connectors. It supports the quality input images of DVD and HDTV (480P/720P/1080i). The Video module also provides one set of Stereo Audio output. - The TUNER Module The RF input terminal is for ANTENNA and CABLE TV channels. 2. Power Management Function The machine provides an automatic power control function. 3. WXGA LCD TV Panel The WXGA LCD TV panel provides high resolution and high contrast image. The number of pixels is 1366 (H) x 768 (V). The contrast is 1000:1. 4. Build in slot-in DVD player This LCD TV build in a slot-in DVD player, and compatible for DVD/CD format disc. (The DVD player may not be supported some of the disk.) 5. Others The LCD TV unit provides cool, middle, warm and user color temperature options. The user may customize their favorite color temperature. 8 3. Names and Functions of Parts Side View The functions of the buttons are described as follows: (Eject): Press to open or close the disc tray. Sketch map (Stop): Press to stop playing the disc. (Play/Pause): Press to play or pause the disc. STANDBY: Press (Standby) to turn on and turn off. VOL.+/A. They are used as / buttons in the OSD Menu screen. B. Press to adjust the volume. CH.+/A. They are used as / buttons in the OSD Menu screen. B. Press to scan through channels. To scan quickly through channels, press and hold down either channels. MENU: Press to display the menu. Press again to exit the menu. SOURCE: Press to cycle display TV, AV, S-Video, Component, DVD, and VGA source menu. When display the OSD-menu, press it to confirm. Front View Sketch map Disc Slot: Place a disc in the disc slot. Note: Insert a disc with the logo-printed side facing the front. (IR) Infrared Receiver: Receives IR signals from the remote control. (Power on / Standby) LED: Press (Power) to turn on and off. Indicator on (Red) Standby mode Indicator on (Green) Power on mode 9 REAR VIEW Rear View REMOTE CONTROL Sketch map Push the power switch (O: Off, I: On). Use the power cord connect to an earthed 120V, 60Hz AC outlet. Signal input and other terminals: . Coaxial Out: Connect to a digital audio component. . RS-232: The D-SUB 9 pins terminal is used as a control port for serial communication between PC and Panel. (For after sales service use only.) . D-SUB(VGA) In: For PC display purpose. Connects to the Mini D-Sub 15 pins analog output connector of the PC display card. . D-SUB(VGA) Audio In: Connect the audio terminal to the audio output terminal of the PC. . YPbPr In: Connect the separate component video cables to the device having component video outputs (YPbPr) to the YPbPr terminal of the TV. YPbPr Audio In: Connect the audio cable to device's audio L and R terminal and to the L and R audio terminal of the TV. . VIDEO In: Connect the video input terminal to the output terminal of the video output device. . S-VIDEO In: Video input for external devices with an S-Video output, such as a camcorder or VCR. . AUDIO In: Connect the audio input terminal to the audio output terminal of the video output equipment. With S-VIDEO audio input signals share this terminal. . RF IN: Connect the antenna or cable set-top box with 75 Ohm F type connector into the RF IN terminal. . AUDIO Out: Audio outputs for external devices. 10 Remote Control Power ( ): Press to turn on and off. Mute ( ): Press to mute the sound. Press again or press , to restore the sound. CCD: Press to select the Closed Caption mode. V-CHIP: Press to select the child protect mode. MTS: Press repeatedly to cycle through the Multichannel TV sound (MTS) options: Mono, Stereo and SAP (Second Audio Program). Favorite: Press repeatedly to cycle through the favorite channel list. PIC.Size: Press repeatedly to cycle through the picture size that best corresponds your viewing requirements: Normal, Full, Wide1, Wide2, Wide3, 4:3, No scale, Panoramic and Normal. Freeze: Press to freeze the picture, press again to restore the picture. P .Mode: Press repeatedly to cycle through the picture mode: Hi-Bright, User, Dark, Normal and Vivid. Display: Press to display the channel information and it disappear after 3 seconds. Sleep: Press repeatedly until it displays the time in minutes (5 Min, 10 Min, 15 Min, 30 Min, 60 Min, 90 Min, 120 Min and, OFF) that you want the TV to remain on before shutting off. To cancel sleep time, press Sleep button repeatedly until sleep OFF appears. Zoom: Press to zoom the image. S.Mode: Press repeatedly to cycle through the sound mode: Normal, News, Cinema, Flat and User. System: Press repeatedly to cycle through the system options: AUTO and NTSC3.58. (This button is activate for AV, S-Video input source.) Add/Erase: Press to add or delete favorite channel. Color Tmp: Press to select the color temperature. 0~9 Number Buttons: In TV mode, press 0~9 to select a channel; the channel changes after 2 seconds. In DVD mode, press 0~9 to input the items. CH Edit: Press to edit channel name. VGA Adj: Press to auto adjust VGA position. Source: Press to select the signal source, such as TV, AV, S-Video, Component, DVD, or VGA. Recall: Press to return previous channel. Enter: To select an item, press ENTER to confirm. VOL / : Press to adjust the volume. CH / : Press to scan through channels. To scan quickly through channels, press and hold down either channels. , , , : Press , , , to move the on-screen cursor. (Continued on next page) 11 REMOTE CONTROL Menu: Press to enter on-screen setup menu, press again to exit. , : Press to skip the forward or backward. : Press to play or pause the DVD disc. : Press to stop playing the disc. , : Press to search the forward or backward. : Press to open or close the disc tray. DVD Menu: Press to return DVD disc menu. Prog: Press to display the program menu. Press it again to exit. Repeat: Press repeatedly to cycle through the options: CHAPTER, TITLE, ALL and nothing. Subtitle: Press to select desired DVD subtitle. Audio: Press to select desired audio track. Setup: Press to display a menu. Press it again to exit menu. Angle: Press to select desired viewing angle of the Video (disc feature). Title: Press to display to DVD disc title. DVD Info: Press to display DVD information. Note: Press CH / on the remote control can turn on TV set from last preview mode. Insertion of Batteries - Turn the remote control upside down, press and slide off the battery cover. - Insert two 1.5V (AAA) batteries into the compartment, take care to observe the and markings indicated inside. - Replace the cover and slide in reverse until the lock snaps. Range of Remote Control - Ensure the remote control is pointed towards the remote control window on the display unit. - No obstacles should be placed between the remote control and the remote control window. - The effective receiving range for the signal is within 5-8 meters from the front of the remote control window, and 30° to the left or right side and 20° above or below the control window. Sketch map 20° 20° 30° 30° 12 Care For Remote Control Avoid spilling liquids on the remote. Avoid dropping or otherwise jarring the remote. Always store the remote control at dry and normal room temperature place. If the remote is nor performing satisfactorily, replace the batteries. The batteries should be replaced after one year. - If the remote control will be idled for a long time (above 1 month) take out the batteries to avoid leakage from the batteries. - Clean up the entire remote control especially the battery compartment if any leakage found. - Do not mix using different kind of new and used batteries together to avoid leakage. - 4. Connect Accessory Devices Connecting a DVD player or other equipment Switch off LCD TV and external equipment before connecting cables. 1. Connect a DVD player or other equipment's Component Video Out (Y,Pb,Pr) to the LCD TV's corresponding Component In (Y,Pb,Pr) terminal. (Fig.1) 2. Connect a DVD player's Audio Out to the TV Component L/R terminal. 3. Press Power to turn on the LCD TV. Turn on external equipment also. 4. Press Source to select COMPONENT signal source. Green Red Blue Fig.1 Red White DVD or other equipment Fig.2 Audio Amplifier Connecting a Audio Amplifier Switch off TV and external equipment before connecting cables. 1. Connect to the LCD TV 's Coaxial Out to the Audio Amplifier Coaxial In terminal by a coaxial cable. (Fig.2) 2. Press Power to turn on the TV. Turn on external equipment also. 3. Press Source to select DVD signal source, and set the Audio Amplifier to coaxial input mode. 4. When DVD is playing, you can enjoy coaxial digital audio by Audio Amplifier. 13 CONNECT ACCESSORY DEVICES Connecting the Computer Switch off LCD TV and external equipment before connecting cables. 1. Connect a computer's VGA Out to the LCD TV's VGA In terminal. 2. Connect a computer's Audio Out to the LCD TV's Audio In terminal. 3. Press Power to turn on the LCD TV. Turn on external equipment also. 4. Press Source to select VGA signal source. Connecting the DVD or VCR player devices Switch off TV and external equipment before connecting cables. 1. Connect a DVD or VCR player's Video Out to the TV's Video In terminal by a Video cable. 2. Connect a DVD or VCR player's S-VIDEO Out to the TV's S-VIDEO In terminal by a S-VIDEO cable. 3. Connect a DVD or VCR player's Audio Out to the TV's L/R terminal by a Audio cable, in this stage, the S-VIDEO and VIDEO is sharing this L/R Audio in channels. 4. Press Power to turn on the TV. Turn on external equipment also. 5. Press Source to select AV or S-VIDEO signal source. Yellow Red White DVD or VCR player 14 Connecting AUDIO OUTPUT jacks to a stereo amplifier Switch off TV and external equipment before connecting cables. 1. Connect the TV Audio Output (R/L) to the stereo amplifier In (R/L). 2. Press Power to turn on the TV. Turn on external equipment also. White Red Stereo Amplifier Insert the Disc to slot-in DVD Player 1. 2. Press Source button to select DVD signal source. Insert your chosen disc into the disc slot on the side panel. Be sure to face the top of the disc (with title etc.) toward the front of the screen. Playback starts. Disc's screen side Connecting directly to cable or an antenna When using 75 coaxial Aerial: Connect directly to the RF terminal of the tuner. VHF Antenna 1m above UHF Antenna Special Antenna Mixer 75 Coaxial Aerial RF(VHF/UHF) terminal 15 BASIC OPERATION OSD OPTION ADJUSTMENT 5. Basic Operation Power ON/OFF The Display is in Standby mode. on the remote control or on the - Press the Power control panel to turn on the unit. The power indicator changes from red to green. on the remote control or on the - Press the Power control panel again to return the display to standby mode. The power indicator changes from green to red. Note: For protecting your LCD TV product, the interval time between turn on the LCD TV product and shut down it should be kept at least one minute. Selection of Input Mode - Press SOURCE on the remote control or on the LCD TV control panel to select the signal source you desired. When no input from the selected signal source, "Main no signal" will appear, press Source on the remote control or on the control panel again to search the next source. Power Display Freeze Zoom Sleep Add/Erase Source Note: The LCD-TV will automatically turn itself off after approximately 15 minutes if no signal input. When no signal is inputted for about 14 minutes. A "No signal and going to power down" wording will appear. Other Function Freeze: Press it to hold the current video and press again to cancel and return to normal viewing. Zoom : Press it to zoom the image. Display: Press once to display the information as side illustrate, and disappear after 3 second; Sleep: Press repeatedly until it displays the time in minutes that you want the TV to remain on before shutting off. When in VGA mode VGA 1280 x 1024 60Hz When in TV mode 68 - - Note: When "Turn off by Timer setting?" wording will appear remain one minute on before shutting off, you can press "<" or ">" button to selected, press "Enter" to confirm. If select "Cancel" or no operation, the LCD-TV will automatically turn off after one minutes, if select "OK", it will turn off immediately. - Add/Erase: Press this button to add/erase current channel to/from the list of favorite directly. Add current channel into the list of favorite if a heart shape mark displaying on the left top of screen. 16 Erase current channel from the list of favorite if a broken heart shape mark Note: displaying. - If you don't want do add/erase this channel to/from the list of favorite, press this button again. - For addition, it will be put at last of the favorite list and the first channel in favorite list will overflow in case of the list is full. OSD Option Adjustment Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the LCD using the menu system. You can access the menu using the buttons on your LCD TV or remote control. The OSD menu displayed in the following sequence (circular display): Video Audio Misc TV Geometric Press Menu button to display the menu system. Press or button to select a menu. Press or button to select an item. Press Enter button on the remote control or Source button on the side panel to activate the function settings in the menu. Press , , or button to select or adjust a setting, press Enter button to confirm. If you do not make a selection within 15 seconds, the main menu closes automatically; the other menus close automatically within 6 seconds. Press button to return OSD-menu. To close an on-screen menu instantly, press Menu button on the remote control or MENU button on the side panel. The Side Panel MENU SOURCE Source Enter Menu 17 TV OPERATIONS ---- VIDEO MENU TV Operations Using the Video Menu Note: Video Menu is just for TV, AV, S-Video, Component, DVD input source mode. It is not available in other input source mode. When smart picture mode is pre-set, the value of the above settings will be different according to different input source. Adjustment of "Contrast" Press Menu button on the remote control, and then press or until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease that will soften the color. Press button to increase that will make white area more bright. Press Enter button to confirm the adjustment and return. Adjustment of "Brightness" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease. Press button to increase that will brighten the dark area for seeing the objects in shadowness more clear. Press Enter button to confirm the adjustment and return. Adjustment of "Back Light" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button and then press or button to select one of "Bright", "Middle" or "Dark" for the balance of back light. Press Enter button to confirm the adjustment. Press button to return. 18 Adjustment of "Saturation" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease. Press button to increase that will make color more intensive. Press Enter button to confirm the adjustment and return. Adjustment of "Hue" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease that will make image more green. Press button to increase that will make image more red. Press Enter button to confirm the adjustment and return. Adjustment of "Sharpness" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press or button to increase or decrease that will make image with more sharp edge. Press Enter button to confirm the adjustment and return. Selection of "Phase" setting Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. 19 TV OPERATIONS ---- VIDEO MENU ---- AUDIO MENU Press button to decrease. Press button to increase. Press Enter button to confirm the adjustment and return. Note: This is a feature just used for YPbPr input source. Selection of "Color Temperature" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to select one of "Cool", "Middle", "Warm" or "User" for balance of whitening. Press Enter button to confirm the selection. Press button to return. If you select the item of "User", a status bar below comes up for you to adjust the color temperature to you desirable value. Hot keys: You can also press Color.Tmp button on the remote control to select you desired item. Selection of "Advance Picture Adjust" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm for sub-selection as shown in the table below. Press Enter button to confirm the selection. Press button to return. Table of Auto Adjustment Setting Item DNR White Peak Limitator CTI Flesh Tone Adaptive LumaControl Status Off, Low, Middle,Strong On, Off Low, Middle, Strong, Off On, Off On, Off Description Selecting to control the sharpness and noise reduction. Select "On" to limit the white peak. Select dynamic color improve level. Select "On" to correct the flash tone automatically. Selecting to control the lum. 20 Using the Audio Menu Adjustment of "Bass" Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease the Bass sound. Press button to increase it. Press Enter button to confirm and return. Adjustment of "Treble" Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease the treble sound, press button to increase it. Press Enter button to confirm and return. Adjustment of "Balance" Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to emphasize the left speaker. Press button to emphasize the right speaker. Press Enter button to confirm and return. 21 TV OPERATIONS ---- AUDIO MENU ---- MISCELLANEOUS MENU Selection of "Surround" Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to select "On" or "Off". Press "Enter" to confirm your selection. Press button to return. Using the Miscellaneous Menu Selection of "Language" Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to choose the OSD language. Press Enter button to confirm your selection. Press button to return. Selection of "Closed Caption" The closed caption features has two options: Adjustment only for TV, AV, S-VIDEO input signal. · Captions: An on-screen display of the dialogue, narration, and sound effects of the TV programs and videos that are closed captioned (usually marked as "C/C" in TV listings. · Text : An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations). To view captions or text: Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or to choose one of "C1", "C2", "C3", "C4", "T1", "T2", "T3", "T4", as follows: · To view captions, highlight C1, C2, C3, or C4 (C1 displays translation of the primary language in your area). Trees near the church. Note: If the program or video you selected is not closed captioned, no captions will display on-screen. (Continued on next page) 22 · To view text, highlight T1, T2, T3, or T4. World Weather New York London HongKong Temp F 53 51 80 C 12 11 25 Current Weather Sunny Cloudy Clear Note: If text is not available in your area, a black rectangle may appear on-screen. If this happens, turn off the Closed Caption feature. Note: A closed when when when caption signal may not display in the following situations: a videotape has been dubbed the signal reception is weak the signal reception is nonstandard Select "Off" to close this function. Press Enter button to confirm your selection. Press button to return. Hot keys: You can also press CCD button on the remote control to select you desired item. Setting of "V-Chip" Some programs and movies include signals that classify the content of the program (dialog, language, sex, violence). The "V-Chip" control feature in this detects the signals and blocks the programs according to your selections. To use this feature, perform the following setup. Adjustment only for TV, AV, S-VIDEO input signal. Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. The "V-Chip" menu includes the "V-Chip Control", "Block MPAA Rating", and "Block TV Rating" functions. You can use these functions after entering the correct PIN code. Entering the PIN code Blocking Reset status: Set your 4-digit code by pressing the Number buttons (0~9), and then press Enter. When the PIN code is already stored: Press the Number buttons (0~9) to enter the 4-digit PIN code used for blocking channels, and then press Enter. Note: The initial password for the system is "0000". If you had forgotten the password, please contact with service centre. (Continued on next page) 23 TV OPERATIONS ---- MISCELLANEOUS MENU If the input is invalid, a message will pop up as below; You can press Enter button to display "Input Your Password Please" menu again, then entering the PIN code, or press , , or button move cursor to "Cancel" and press Enter button to close up this menu. Using the "V-Chip Control" item When enter the "V-CHIP" menu, select "V-Chip Control". Press or button to highlight the "V-Chip Control" item. Press Enter button to confirm and then press or button to select "ON" or "OFF". ON : TV Blocking and MPAA Blocking are activate. OFF : TV Blocking and MPAA Blocking are not activate. Press button to return or press Menu button to exit. Using the "Block MPAA Rating" item When enter the "V-CHIP" menu, select "Block MPAA Rating". Press or button to highlight the "Block MPAA Rating" item. Press Enter button to confirm. Press or button to select an item, then press Enter button to lock (display " ") or unlock (display " "). Press Menu button to exit the sub-menu. For Movie previously shown in theaters: · G and Above (general audience) · PG and Above (parental guidance suggested) · PG-13 and Above (13 years and older) · R and above (restricted) · NC-17 and Above (18 years and older) ·X (adult) If you set PG-13 and Above : G and PG movies be available, PG-13, R, NC-17, and X will be blocked. 24 Using the "Block TV Rating" item From the "V-CHIP" menu, select "Block TV Rating". Press or button to highlight the "Block TV Rating" item. Press Enter button to confirm. Press , , or button to select an item, then press Enter button to lock (display " ") or unlock (display " "). Press Menu button to exit the sub-menu. For Television programs including made-for-TV movies: General TV Ratings: · TV-G and Above · TV-PG and Above · TV-14 and Above · TV-MA Children TV Ratings: · TV-Y and Above · TV-Y7 (general audience) (individual categories do not apply) (parental guidance suggested) (14 years and older) (mature audience) (youth) (individual content categories do not apply) (youth, 7 years and up) Content Categories: · Dialog - sexual dialogue · Language - adult language · Sex scenes - sexual situations · Violence · F Violence - fantasy violence (applies (applies (applies (applies (applies to TV-PG and Above, to TV-PG and Above, to TV-PG and Above, to TV-PG and Above, only to TV-Y7) TV-14) TV-14 and Above, TV-MA) TV-14 and Above, TV-MA) TV-14 and Above, TV-MA) Unlocking programs temporarily If you try to watch a TV program that exceeds the TV Rating you set, the TV V-CHIP BLOCK enters program lock mode. You can either TV-PG unlock the program temporarily or select LV a non-locked program to watch, press Enter Password or button to select the program. To temporarily unlock the program, press the Number buttons (0~9) to enter your 4-digit PIN code. If the correct code is entered, the program lock mode is released and the normal picture appears. Hot keys: You can also press V-CHIP button on the remote control to enter V-Chip menu. 25 TV OPERATIONS ---- MISCELLANEOUS MENU Setting of "Parental" The TV programs and movies shown on TV are given a rating signal based on the following rating systems. To block programs you feel unsuitable for your children, you need to set the TV for the desired rating systems. The TV's "Parental" control feature functions by receiving the rating signal from your local broadcasting station or cable service provider. Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. The "Parental" menu includes the "Channel Lock", "Video Lock", "Change Password" and "Clear All" functions. You can use these functions after entering the correct PIN code. · Entering the PIN code Blocking Reset status: Set your 4-digit code by pressing the Number buttons (0~9), and then press Enter. When the PIN code is already stored: Press the Number buttons (0~9) to enter the 4-digit PIN code used for blocking channels, and then press Enter. · Note: The initial password for the system is "0000". If you had forgotten the password, please contact with service centre. If the input is invalid, a message will pop up as below; You can press Enter button to display "Input Your Password Please" menu again, then entering the PIN code, or press , , or button move cursor to "Cancel" and press Enter button to close up this menu. Press or button to choose an item as below table showing. Press Enter button to confirm. Press button to return. (Continued on next page) 26 Table of Parental Setting Items Channel Lock Video Lock Status All channels TV, AV, S-Video, Component, DVD, VGA Description Use the CH / and Enter buttons to select the channel you desired to lock. Use / and Enter buttons to select the Video you desired to lock. Enter a new 4-digit code by using the number keys on the remote, and then confirm the new code by entering it a second time, You will get a confirmation message when your code has been successfully changed. Press Enter button to clear all present Parental setting. Change Password Clear All Selection of "Blue Mute" Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to choose "On" or "Off", when select "On" to set screen to a pleasant blue background when it detects no signal available if turn on. Press Enter button to confirm your selection. Press button to return. Using "Default" Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm, it will reset to restore factory default settings. After that, a confirmation message will pop up. Note: Just reset the items in the setup menu don't include the protected-items (Needs pin code enter, such as password, video lock, and channel lock) and properties such as skipped channel, channel name. 27 TV OPERATIONS ---- TV MENU ---- GEOMETRIC MENU Using the TV Menu Note: TV menu is only for TV input source mode, thus it is not available in other input source mode. The locked channel will be skipped during the searching. Using the "Auto Search" Press Menu button, and then press or button until the "TV" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press button to return. Using the "Tuner Mode" Press Menu button, and then press or button until the "TV" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to choose "Air" or "Cable". Press Enter button to confirm. Press button to return. Using the "Channel Skip" Press Menu button, and then press or button until the "TV" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to scan which channel is skipped, there is a the channel. Press Enter button to toggle the channel will be skipped or not. Press button to return. Using the "Channel Name" Press Menu button, and then press or button until the "TV" menu appears. Press or button to highlight the item. Press Enter button to confirm, it will display "Channel Name" list. Use , , or button for select, and move cursor to "OK", then press Enter button for confirm you selection. If you want to cancel this operation, move 28 cursor to "Cancel" and press Enter button for close this setting. Press button to return. Note: It will be invalid if the current source is not TV. Hot keys: You can also press CH.Edit button on the remote control. Selecting Channel Press CH +/- button on the remote control to search the channels, the channel number will increase or decrease by 1 for each pressing excluding the skipped channels. Press number buttons 0~9 to select the corresponding channel content. If the channel number is bigger than 9, just press the two number buttons successively. If the channel number is bigger than 100, just press the three number buttons successively. The time interval should not exceed 2 seconds. If the channel number you pressed is bigger than the maximum channel number that the setting is permitted, the maximum numbered channel content will be remained. Channel Preview Press Recall button to switch between present channel and previous channel. (Only for TV) Hot keys: You can also press Recall button on the remote control. Using the Geometric Menu Note: If your current input source is "VGA" , push Menu button enter into this menu. It is not available in other input source mode. When smart picture mode is pre-set, the value of the above settings will be different according to different input source. Using "Contrast" Press Menu button on the remote control, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease that will soften the color. Press button to increase that will make white area more bright. Press Enter button to confirm the adjustment and return. 29 TV OPERATIONS ----GEOMETRIC MENU Using "Brightness" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease. Press button to increase that will brighten the dark area for seeing the objects in shadowness more clear. Press Enter button to confirm the adjustment and return. Using "Back Light" Press Menu button , and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press or button to select one of "Bright", "Middle" or "Dark" for the balance of back light. Press Enter button to confirm the adjustment. Press button to return. Using "Auto Setting" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press button to return. Note: This item will auto-adjust the picture display. Hot keys: You can also press VGA.Adj button on the remote control. Using "Phase" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. 30 Press button to decrease and press button to increase it. Press Enter button to confirm and return. Using "Manual Clock" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease the menu clock. Press button to increase it. Press Enter button to confirm and return. Using "Display Adjustment" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm for sub-selection as shown in the table below. Press Enter button to confirm your selection. Press button to return. Table of Display Adjustment Items Vertical Position Horizontal Position Use " Use " Use " Use " Description " or " " to select it and press "ENTER" to confirm. " or " " to move the image up or down. " or " " or " " to select it and press "ENTER" to confirm. " to move the image left or right. 31 DVD OPERATION DVD Operations AUDIO CD PLAYBACK OPTIONS - Fast Forward/Backward Press the ( ) button during ) or ( playback. Each time you press the ( ) ) or ( button, the playback speed changes as shown. ·FWD( ): 2x 8x 16x 32x 1x. ): 2x 4x 8x ·REV( 16x 32x 1x. Press the PLAY button to resume normal playback. - Basic Playback Press the Power( ) button on the TV to turn the unit on. Insert your chosen disc into the disc slot on the side panel. Be sure to face the top of the disc (with title etc.) toward the front of the screen. If the input source is in DVD mode, the disc will auto play, if the input source is in other mode, please press Play/Pause ( ) button on the remote control or the side control panel, the TV will auto change to DVD mode and will auto play. Press the Eject ( ) button on the remote control or side control TV to remove the disc. - Skip a Chapter or a Track ) button or Skip ( ) Press the Skip ( button to locate a desired chapter during playback. Each time you press the button, a chapter or track is skipped. · Press the Skip ( ) button to locate succeeding chapters or tracks. · Press the Skip ( ) button to go back to the beginning of the current chapter or track. · Press the Skip ( ) button twice in quick succession, playback will start from the beginning of the preceding chapter or track. - Stop Playback Press the Stop ( ) button to stop playback. At this time the DVD video player stops playback temporary and maintains the current playback position. · If you Play/Pause ( ) button is pressed, playback will resume from the location where you stopped playback. Press the Stop ( ) button again to stop playback fully. (At this time if you press Play/Pause ( ) button, the disc playback starts from the beginning.) - OSD(On-Screen Display) You can display the playback status on the TV screen as follows: Title, Chapter number, Playing time. Press the DVD.info button during DVD playback. Title and Chapter information appears on the screen. Each time you press the Display button, the OSD changes as follows. · DVD: Title Elapsed Title Remain Chapter Elapsed Chapter Remain Display off Note: The OSD display may be different depending on the type of DVD disc. - Pause Playback Press the Play/Pause ( ) button during playback. Press the Play/Pause ( ) button again to return to normal playback. 32 - Selecting the disc menu Press the DVD Menu button during playback. Use the or Enter button to select the desired menu option. - Audio Used to change the audio-related setting during DVD playback. Each time you press it, the set value is changed. Note: · Depending on the disc, Audio setup may not be possible. Audio CD Playback options - Repeat playback You can play a specific title, chapter, track, or segment repeatedly. Press the Repeat button during playback. Each time you press the Repeat button, the repeat mode changes as follows. · DVD: Chapter Title All Repeat Off - OSD(On-Screen Display) You can display the track, and playback time status on the TV screen. Press the DVD.info button during CD playback. Track information appear on the screen. Each time you press the Display button, the OSD changes as follows: Single Elapsed Single Remain Total Elapsed Total Remain - Programmed Playback You can arrange the playback order of tracks on the disc. Press the Prog. button in the stop mode or during playback. Use the buttons to select the program position. Use the 0~9 number buttons to enter the desired Title/Chapter numbers. · If you input a wrong number, press button. · Depending on the disc, programmed playback menu may look different from the example shown. - Stop Playback Press the Stop ( ) button to stop playback. At this time the DVD video player stops playback temporally and maintains the current playback position. · If you Play/Pause ( ) is pressed, playback will resume from the location where you stopped playback. Press the Stop ( ) button again to stop playback fully. (At this time if you press Play/Pause ( ) button, the disc playback starts from the beginning.) - Pause Playback Press the buttons to select START and the press the Enter button. · The programs you selected will start to playback in the order. · To resume normal playback, select Stop in step · Select EXIT to quit the programmed playback menu. Note: Depending on the disc, programmed playback may not be possible. Press the Play/Pause ( ) button during playback. Press the Play/Pause ( ) again to return to normal playback. - Fast Forward/Backward Press the ( ) or ( ) button during playback. Each time you press the ( ) or ( ) button, the playback speed changes as shown. 33 DVD MENU OPTIONS ·FWD( ·REV( ): ): 2x 16x 2x 4x 32x 8x 8x - Selecting camera angles If the scene was recorded from multiple angles, you can easily change the camera angle of the scene you are currently watching. Press the Angle button during playback. Repeatedly press the Angle button to select the desired angle. Note: · You can only change the angle for DVDs that provide multiple angles of scenes. · The angle function will not work on DVD video discs that do not contain scenes recorded at different angles. · The number of angles varies from disc to disc. 16x 32x. Press the Play/Pause ( ) button to resume normal playback. - Repeat playback You can play a specific track repeatedly. Press the Repeat button during playback. Each time you press the Repeat button, the repeat mode changes as follows. · Track All Repeat Off DVD Menu options When in the DVD input, press Setup button, the DVD menu is displayed. - Disc OSD Language Selection The on-screen display can be shown on the screen in your specified language. Press the Setup button and then use buttons to select OSD LANGUAGE. Press the Enter or button and then the buttons to select your desired language. All the on-screen displays will appear in the selected language. Press the Setup button to exit this menu. - Digital Audio Output You can select the output for SPDIF. Press the Setup button and then use buttons to select DIGITAL OUTPUT. Press the Enter or button and then the buttons to select SPDIF OFF, RAW or PCM ONLY. Press the Enter button. Press the Setup button to exit this menu. - TV Display You can watch TV in various picture formats. Press the Setup button and then use buttons to select TV DISPLAY. Press the Enter or button and then the buttons to select 4:3 PAN SCAN, 4:3 LETTER BOX, 16:9 WIDE. Press the Enter button. Press the Setup button to exit this menu. Note: Depending on the disc, the TV screen feature may not be available. - Screen Saver The screen saver appears when you leave the DVD player in stop mode for about five minutes. After an additional five minutes, the DVD Player automatically turns itself off. About DVD Screen Saver If you pause or stop a picture of a DVD video disc and leave it still for approximately 10 seconds, the screen saver of the player automatically appears. To turn off the screen saver, press any button related DVD on the remote control. 34 - Last Scene Memory This player memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the player or turn off the set. If you load a disc that has the scene memorized, the scene is automatically recalled. Note: This player does not memorize the scene of a disc if you switch off the player before commencing to play the disc. - Selection of Dynamic Press the Setup button and then use buttons to select DYNAMIC. Press the Enter or button and then the buttons to select FULL ~ OFF. Press the Enter button. Press the Setup button to exit this menu. - Selecting an Audio Language - Selection of Down Mix Press the Setup button and then use buttons to select DOWN MIX. Press the Enter or button and then the buttons to select LT/RT, STEREO. Press the Enter button. Press the Setup button to exit this menu. Select your preferred audio language. (The disc must contain the selected language.) Press the Setup button and then use buttons to select AUDIO. Press the Enter or button and then the buttons to select your desired language. Press the Enter button. Press the Setup button to exit this menu. - Selecting a subtitle language Select your preferred subtitle language. (The disc must contain the selected language.) You can also select another available subtitle language during playback with the Subtitle button on the remote control during playback. Press the Setup button in the stop mode and then use buttons to select SUB TITLE. Press the Enter or button and then the buttons to select your desired language. Press the Enter button. Press the Setup button to resume normal playback. GO TO DOLBY DIGITAL SETUP - Selection of Dual Mono Press the Setup button and then use buttons to select DUAL MONO. Press the Enter or button and then the buttons to select STEREO, L-MONO, R-MONO, MIX-MONO. Press the Enter button. Press the Setup button to exit this menu. 35 DVD MENU OPTIONS TECHNICAL SPECIFICATION SUPPLIED ACCESSORIES - Disc menu language selection Select your preferred language for the disc menus and DVD messages. (The disc must contain the selected language.) Press the Setup button and then use buttons to select DISC MENU. Press the Enter or button and then the buttons to select your desired language. Press the Enter button. The menus and on-screen displays will appear in the selected language. Press the Setup button to exit this menu. - Changing the password Press the Setup button and then use buttons to select PASSWORD. Press the button and then use number buttons to key in a 4-digit password. Press the 4 digit password for old password and enter a new 4 digit for new password. Enter it again. - Parental Control Setup Use to block viewing of unsuitable discs. Press the Setup button and then use buttons to select PARENTAL. Press the button and then use number buttons to key in a 4-digit password. Be sure to remember the password. If you key in an incorrect number, press the Setup button and start over. Use the buttons to set the restriction level from 1 to 8. Viewing becomes more restricted as the number decreases. · 1: Kid safe · 2: G (General audience) · 3: PG (Parental audience suggested) · 4: PG-13 (13 years and older) · 5: PG-R · 6: R (Restricted) · 7: NC-17 (18 years and older) · 8: Adult (Adults only) Press the Setup button to resume normal playback. Note: If you ever forget your password, key in 0000 on the remote control. Press the Setup button to exit this menu. Note: The initial password for the system is "0000". If you had forgotten the password, please contact with service centre. - Default Use to block viewing of unsuitable discs. 36 6. Technical Specification Product Model: Screen Size: Screen Area: Aspect Ratio: External Size: Net Weight: Resolution: Pixel Dot Pitch: Color: Gray Scale: High Brightness: Contrast(Dark Room): TV System: Playable Disc Type Sound: Sound Effect: Power Supply: Power Consumption: LCT2701TD 27" diagonal 596.259mm(H) x 325.232mm(V) 16:9 698mm(W) x 513mm(H) x 99mm(D) (w/o Stand) 698mm(W) x 571mm(H) x 250mm(D) (with Stand) 13.9kg (with Stand) 1366 (H) x 768 (V) pixels (Each pixel has R/G/B 3 color cells) 146.0µm(H) x 436.5µm(V) 16.7 millions of colors (R/G/B each 256 scales) 256 (R/G/B each 8-bit) 550cd/m2 1000:1 (Typical) NTSC M DVD/CD Mono, Stereo, SAP (BTSC) Spatial Effect and Surround AC 120V, 60 Hz 200W D-Sub 15 Pin (Analog RGB Input) D-Sub 9 Pin (RS-232 Terminal) Component Video - YPbPr x 1 RCA Terminals Video Input RCA Terminals Input/Output Terminal: S-Video Input Mini Din 4 Pin Terminal 1 set of Stereo Audio Output Terminals (RCA, L&R) Coaxial Output Terminal x 1 Audio Input for Video/S-Video Audio Input for YPbPr x 1 Audio Input for PC (3.5mm) Agent System: UL, cUL, FCC 7. Supplied Accessories Remote control .................................................. 1 Batteries (AAA) ................................................... 2 Owner's manual (This booklet)........................... 1 Stand ................................................................ 1 Insertion Card ................................................... 1 Warning Notice ................................................. 1 NOTE: · The specifications shown above may be changed without notice for quality improvement. 37 SUPPORT THE SIGNAL MODE CLEAN AND SIMPLE TROUBLESHOOTING 8. Support the Signal Mode A. D-Sub Mode (VGA) Resolution 640 x 480 Horizontal Frequency (KHz) 31.50 37.86 35.16 800 x 600 37.90 46.90 48.08 1024 x 768 B. HDTV Mode (YPbPr) Resolution 480i 480p(720x480) 720p(1280x720) 1080i(1920x1080) Horizontal Frequency (KHz) 15.734 31.468 45.00 33.75 Vertical Frequency (Hz) 59.94 59.94 60.00 60.00 48.40 Vertical Frequency (Hz) 60.00 72.81 56.25 60.32 75.00 72.19 60.00 - When the signal received by the Display exceeds the allowed range, a warning message shall appear on the screen. - You can confirm the input signal format from the on-screen. 9. Cleaning and Simple Troubleshooting 1 Important: - Make sure that the power cable is removed from the AC outlet before cleaning the product. - Do not use volatile solvent (such as toluene, rosin and alcohol) to clean the Display. Such chemicals may damage the housing, screen glass and remote control, and cause the paint to peel. - Use a soft cotton cloth for cleaning. - If the housing or remote control are seriously contaminated, use a soft cloth moistened with diluted neutral clean the Display. Wring water out of the cloth before cleaning to prevent water from penetrating into the housing. Wipe the Display with a dry cloth after cleaning. - Use a soft cotton cloth to clean the screen gently. - The screen glass is very fragile; so do not scrape it with any sharp object. Do not press or tap the screen to avoid cracking. When the screen is seriously contaminated, use a soft cloth moistened with diluted neutral cleaner to clean the Display. Wring water out of the cloth before cleaning to prevent water from penetrating into the housing. Wipe the display with a dry cloth after cleaning. Use the following check list for troubleshooting when you have problems with your unit. Contact your local dealer for assistance if problem persist. (Continued on next page) 2 Cleaning of Housing and Remote Control: 3 Cleaning of Screen: 4 Simple Troubleshooting: 38 SYMPTOMS POWER TV/DVD does not operate. TV Broadcast reception POSSIBLE SOLUTIONS · Make sure the power cord is plugged in. · Try another Wall outlet. · Station or Cable TV experiencing problems, tune to another station. Poor sound or No sound. · Check Volume adjustments. · Check for sources of possible interference. · Station or Cable TV experiencing problems, tune to another station. · Check antenna or Cable TV connections, reorient antenna. · Check for source of possible interference. · Check picture control adjustments. · Station or Cable TV experiencing problems, tune to another station. · Station signal is weak, reorient antenna to receive weaker station. · Check for source of possible interference. · Station or Cable TV experiencing problems, tune to another station. · Check picture control adjustments. · Check antenna or Cable TV connections, reorient antenna. · Check for source of possible interference. · Station or Cable TV experiencing problems, tune to another station. Poor picture or No picture. Poor reception on some channels. Poor color or no color. Picture wobbles or drifts. No CATV reception. Horizontal or diagonal bars on screen. TV shuts off. Display is not shown in your language. Remote Control · Cable TV company is scrambling signal. · Check antenna orientation. · Check all Cable TV connections. · Check antenna connections, reorient antenna. · Check for sources of possible interference. · No broadcast on station tuned with Auto off activated. · Sleep Timer is set. · Power interrupted. · Select proper language in the menu options. · Aim the remote control at the remote sensor. The remote control does not function. · Operate within approx.5 meters or reduce the light in the room. · Clear the path of the beam. · The batteries are weak. Replace the batteries. · Check the batteries are inserted correctly. DVD · No disc id inserted. Playback doesn't start. No picture. · The disc may be dirty. Clean up the disc. · The unit cannot play CD-ROMs, etc. · Source select is not set correctly. 39 CLEAN AND SIMPLE TROUBLESHOOTING Simple Troubleshooting (Continued) SYMPTOMS DVD No sound. Stopping playback, search, repeat play, or program play, etc. cannot be performed. Audio sound track and/or subtitle language is not changed when you play back a DVD. No subtitle. Angle cannot be changed. · Check that the input selector of the amplifier is set properly. · The unit is set to Mute mode. · Some discs may not do some of the functions. POSSIBLE SOLUTIONS · Multilingual language is not recorded on the DVD disc. · Some discs have no subtitles. · Subtitle are cleared. Press the Subtitle button. · Multi-angles are not recorded on the DVD disc. 40