User manual AKAI LCT3201TD

1. Safety Guidelines Caution: Always use a power cable is properly grounded. Please use the AC cords listed below for each area: USA ...................... UL Canada ................ CSA/cUL FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio / TV technician for help. FCC Warning To assure continued FCC compliance, the user must the provided grounded power supply cord and the provided shielded video interface cables to connect to this equipment. Also, any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. Labels A. CLASSIFICATION LABEL B. WARNING LABEL 1. CLASS 1 LASER PRODUCT 2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover or remove screws. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel. Do not insert any metallic object into the System. 1 Important Safeguards Before using your TV, please read these instructions completely, and keep this manual for future reference. Carefully observe and comply with all warnings, cautions and instructions placed on the unit or described in the operating instructions or service manual. The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties: WARNING----- Ignorance or inappropriate use may cause damage to the product. ATTENTION---Ignorance or inappropriate use may cause injury to the user. Examples: Prohibition Warning (Attention) symbol (indicating "Electric Shock"). WARNING Never place TV on an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV. Never overload wall outlets and extension cords. Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse. Keep the product away from moisture: - Do not expose this appliance to rain or moisture. - If water penetrates into the product, stop the operation; unplug the connector and contact with your dealer. Continuous use in this case may result in fire or electric shock. WARNING Never place item such as vases, aquariums, or candles on top of the TV. 2 Never use a damaged power cord: Heavy objects, heat or tensile force may damage the power cord and cause fire or electric shock. Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV: - on a bed, sofa, rug, or similar surface; - too close to drapes, curtains, or walls; or - in a confined space such as bookcase, built-in cabinet, or any other place with poor ventilation. The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV. Do not use the product if any abnormality occurs: If any smoke or odor becomes apparent, unplug the connector and contact the manufacturer immediately. Do not try to repair the product by yourself. WARNING Avoid using dropped or damaged appliances: If the product is dropped and the housing is damaged, the internal components may function abnormally. Unplug the connector immediately and contact the manufacturer for repair. Continuous use of the product may cause fire or electric shock. WARNING While it is thundering, do not touch the connecting cables or apparatus. ATTENTION Do not install the product close to smoke or moisture: Fire or electric shock may be caused when the product is installed close to smoke or moisture. Do not installed the product in an area with heavy dust or high humidity: Fire or electric shock may be caused when the product is installed in a place with heavy dust or high humidity. Instructions for moving the product: Ensure that the power connector and any other leads are unplugged before moving the product. 3 The power cable should be kept away from heat sources: The heat produced by any heat source may melt the covering of the power cable. Unplug the connector Hold the power connector when removing the power cable: Pulling the power cable itself may damage the wires inside the cable and cause fire or electric shock. Do not touch the connector with wet hands: To avoid risk of electric shock. ATTENTION Insert batteries in accordance with instructions: Insert the batteries with correct polarities (positive and negative ). Incorrect polarities may cause breakage and leakage of the batteries, hurt operators and contaminate the remote controller. Do not block or cover the vents: Blocking the vents may cause overheating and fire. Do not install the product in a place with little or no ventilation. Never cover the vents with towels, blankets or dusters. Unplug the connector: Unplug the power connector when the product will not be used for a long time. Unplug the connector Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges.(see Section 810 of the National Electric Code.) Antenna lead-in wire Antenna discharge unit (NEC Section 810-20) Ground clamp Electric service equipment Grounding conductors (NEC Section 810-21) Power service grounding electrode system (NEC Art 250 Part H) Ground clamp Use extreme care to make sure you are never in a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits. Never attempt to install any of the following during lightning activity: a). an antenna system; or b).cables, wires, or any home theater component connected to an antenna or phone system. 4 Others: 1). The LCD panel on this TV is manufactured using an extremely high level of precision technology; however, an occasional pixel (dot of light) may display constantly on the screen. This is a structural property of LCD technology and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance. 2). LCD (Liquid Crystal Display) may cause interference in image, sound, etc. of the other electronic equipment that is easy to receive electromagnetic waves (i.e. AM radios and video equipment) under certain installed condition. In particular, it may affect electronic equipment beyond the residential until where a LCD TV is used. 3). The screen on this TV is manufactured from glass. To prevent damage, never strike the glass with a sharp or heavy object. 4). Your LCD television contains a small amount of Mercury. When the television is no longer useful, please follow local electronic waste guidelines for proper disposal. 5). If you have the LCD screen facing to the sun, the LCD screen will be damaged. Locate the TV in the place such away from windows side or out side of the rooms with windows. 6). This product is designed for indoor use only. The operation temperature are 5°C ~ 30°C. 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that product heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. The apparatus shall not be exposed to dripping or splashing and that no objected filled with liquids, such as vase, shall be placed on the apparatus. 6 Contents 1. Before use ..................................... 8 1.1 Open the Package ....................... 8 1.2 Installation .................................... 8 Setting of "V-Chip" .............................. 33 Setting of "Parental" ............................ 37 Selection of "Blue Mute" ...................... 39 Using "Default" .................................... 39 4 Using the TV Menu ............................ 40 Using the "Auto Search" ...................... 40 Using the "Tuner Mode" ...................... 40 Using the "Channel Skip" .................... 41 Using the "Channel Name" .................. 41 5 Using the Geometric Menu ............... 42 Using "Contrast" .................................. 42 Using "Brightness" ............................... 42 Using "Back Light" ............................... 43 Using "Auto Setting" ............................ 43 Using "Phase" ..................................... 44 Using "Manual Clock" .......................... 44 Using "Display Adjustment" ................. 45 Selecting Channel ............................... 45 Channel Preview ................................. 45 2. Product Features ........................... 9 3. Accessories ................................... 9 4. Names and Functions of Parts ...... 10 4.1 Side View ..................................... 10 4.2 Front View .................................... 11 4.3 Rear View .................................... 11 4.4 Remote Control ............................ 13 5. Connect Accessory Devices .......... 17 6. Basic Operation ............................. 20 6.1 Power ON/OFF ............................ 20 6.2 Selection of Input Mode ............... 20 6.3 Other Function ............................. 20 6.4 Using the POP double-window feature ................. 21 6.5 OSD Option Adjustment ............... 22 6.6 OSD Functions of TV System ...... 23 1 Using the Video Menu .................... 23 Adjustment of "Contrast" .................. 24 Adjustment of "Brightness" ............... 24 Adjustment of "Back Light" ............... 25 Adjustment of "Saturation" ............... 25 Adjustment of "Hue" ......................... 26 Adjustment of "Sharpness"............... 26 Selection of "Phase" setting ............ 27 Selection of "Color Temperature" ..... 27 Selection of "Advance Picture Adjust" .............................................. 28 2 Using the Audio Menu ................... 29 Adjustment of "Bass" ........................ 29 Adjustment of "Treble" ...................... 29 Adjustment of "Balance" ................... 30 Selection of "Surround" .................... 30 3 Using the Miscellaneous Menu ..... 31 Selection of "Language" ................... 31 Selection of "Closed Caption" ......... 31 6.7 Operation of DVD System ........... 46 1 Suit Table Disc Types .................. 46 2 Play a Disc .................................... 46 3 Function Buttons ......................... 47 4 Program Setting ........................... 50 5 Setup of DVD ................................ 50 GENERAL SETUP PAGE.................... 50 SPEAKER SETUP PAGE .................... 52 DOLBY DIGITAL PAGE ....................... 53 PREFERENCE PAGE ......................... 54 7. Technical Specification .................. 56 8. Support the Signal Mode ............... 57 9. Cleaning and Simple Troubleshooting............................. 58 7 1. Before use The product is a 32" WXGA (WXGA resolution) LCD TV/DVD Player Combo. It has passed the UL and cUL safety certifications, and is an ideal product for personal and commercial use. The product is a precise electronic product. Users should read the following instructions carefully to maximize the performance and life span of the product: 1.1 Open the Package - - The product is packaged in a carton together with other standard accessories. Any optional accessories shall be packed separately in another carton. Due to the size & weight of the product, it is recommended that it should be moved by a minimum of two people. The protective glass and the glass substrate are installed on the front of the product. Since both glasses can be broken and scraped easily, move the product gently. Never place the unit with the glass facing downwards unless it is protected with soft pads. When opening the carton, check that the product is in good condition and that all standard accessories and items are included. Whenever possible, use the handles on the back of the Display for transport. 1.2 Installation - Please use caution if wall mounting this product. Follow all directions from the manufacturer of the wall mount and be sure to securely fasten the product to the mount. While the TV can be wall mounted, improper wall installation may void the warranty. Due to the higher power consumption, always use the jack exclusively designed for this product. If an extended line is required, please consult with your service agent. The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with higher humidity so as not to shorten the service life of the electronic components. Please ensure the product be installed horizontally, any 90 degree clockwise or counterclockwise installation may induce poor ventilation and subsequent component damage. To protect the screen and avoid screen burn, do not hold on a static picture for a long time. 8 2. Product Features The 32 LCD TV/DVD Player Combo provides quality image displays and is suitable for a variety of multi media applications: 1. Available input signals - The standard PC module provides VGA (D-SUB 15 PIN), and a RS-232 (D-SUB 9 PIN MALE) communication connector. The product supports PC mode image resolutions up to (1280 x 1024@60Hz) with a vertical frequency of 60 Hz. - The Video module provides composite video (RCA), S-video (DIN 4 PIN) and component video (RCA) input connectors. It supports the quality input images of DVD and HDTV (480P/720P/1080i). The Video module also provides one set of Stereo Audio output. - The TUNER Module The RF input terminal is for ANTENNA and CABLE TV channels. 2. Power Management Function The machine provides an automatic power control function. 3. WXGA LCD TV Panel The WXGA LCD TV panel provides high resolution and high contrast image. The number of pixels is 1366 (H) x 768 (V). The contrast is 1000:1. 4. Build in slot-in DVD player This LCD TV build in a slot-in combo DVD player, and compatible for DVD/CD/CD-R/ CD-RW format disc. 5. Others - PIP/POP Function: The user may watch image from two source at same time. - The LCD TV unit provides cool, middle, warm and user color temperature options. The user may customize their favorite color temperature. 3. Accessories 1 2 3 4 5 6 User Manual x 1 AC Cable x 1 Remote Control x 1 Battery(UM-3/R6P/AA) x 2 Warranty Card x 1 Insertion Card x 1 9 4. Names and Functions of Parts 4.1 Side View The functions of the buttons are described as follows: STANDBY: Press (Standby) to turn on and turn off. VOL.+/A. They are used as / buttons in the OSD Menu screen. B. Press to adjust the volume. CH.+/A. They are used as / buttons in the OSD Menu screen. B. Press to scan through channels. To scan quickly through channels, press and hold down either channels. MENU: Press to display the menu. Press again to exit the menu. SOURCE: Press to cycle display TV, AV, S-Video, Component, DVD, and VGA source menu. When display the OSD-menu, press it to confirm. (OPEN/CLOSE): Press to open or close the disc tray. (STOP): Press to stop playing the disc. (PLAY/PAUSE): Press to play or pause the disc. 10 4.2 Front View Sketch map (IR) Infrared Receiver: Receives IR signals from the remote control. (Power on / Standby) LED: Press (Power) to turn on and off. Indicator on (Red) Standby mode Indicator on (Green) Power on mode 4.3 Rear View Sketch map (Continued on next page) 11 Push the power switch (O: Off, I: On). The power indicator on the front of the panel should now display red, indicating that the LCD TV is in standby mode. Use the included power cord and connect to an earthed 100-240V, 50/60Hz AC outlet. Note: Shut down the power switch, turn on it again after the power indicator is extinguished entirely. Signal input and other terminals: A. COAXIAL OUT: This terminal is used as a digital audio output to audio amplifier. B. RS-232: The D-SUB 9 pins terminal is used as a control port for serial communication between PC and Panel. C. D-SUB(VGA) INPUT: For PC display purpose. Connects to the Mini D-Sub 15 pins analog output connector of the PC display card. D-SUB(VGA) AUDIO INPUT: Connect the audio terminal to the audio output terminal of the PC. D. YPbPr INPUT: Connect the separate component video cables to the device having component video outputs (YPbPr) to the YPbPr jacks of the TV. YPbPr AUDIO INPUT: Connect the audio cable to device's audio L and R jacks and to the L and R audio jacks of the TV. E. VIDEO INPUT: Connect the component video input terminal to the component output terminal of the video output device. F. S-VIDEO INPUT: Connects to the S-Video out jack of your VCR or other video equipment that has S-Video. G. AUDIO INPUT: Connect the audio input terminal to the audio output terminal of the video output device. With S-VIDEO audio input signals share this terminal. H. RF IN: Connect antenna or cable 75 Ohm coaxial Aerial to receive TV/CABLE signal. I. AUDIO OUTPUT: Connect audio amplifier or other TV set that with audio input. 12 4.4 Remote Control Power ( ): Press to turn on and off. Mute ( ): Press to mute the sound. Press again or press , to restore the sound. CCD: Press to select the Closed Caption mode. V-CHIP: Press to select the child protect mode. MTS: Press repeatedly to cycle through the Multi-channel TV sound (MTS) options: Mono, Stereo and SAP (Second Audio Program). Favorite: Press repeatedly to cycle through the favorite channel list. PIP. Pos: Press to change the PIP window position under PIP mode. PIP. Size: Press to cycle through the PIP size, such as Large, Medium, Small. Add/Erase: Press to add or delete favorite channel. PIP: Press to cycles through the different POP or PIP modes, such as Basic PIP, LR POP, and exit. 0~9 Number Buttons: In TV mode, press 0~9 to select a channel; the channel changes after 2 seconds. In DVD mode, press 0~9 to input the items. Zoom: Press to zoom the image max from 8 times to minimally 1/8 times. Recall: Press to return to previous channel. P.Mode: Press repeatedly to cycle through the picture mode: Hi-Bright, User, Dark, Normal and Vivid. P.Size: Press repeatedly to cycle through the picture size that best corresponds your viewing requirements: Normal, Full, Wide1, Wide2, Wide3, 4:3, No scale, Panoramic and Normal. When in POP mode, it can select picture size is: Full, 4:3 and Normal. Vol / : Press to adjust the volume. Ch / : Press to scan through channels. To scan quickly through channels, press and hold down either channels. Freeze: Press to freeze the picture, press again to restore the picture. (Continued on next page) 13 Menu: Press to enter into the on-screen setup menu, press again to exit. S.Mode: Press repeatedly to cycle through the sound mode: Normal, News, Cinema, Flat and User. , , , , Enter: Press , , , to move the on-screen cursor. To select an item, press ENTER to confirm. And it can also press or to scan through channels, press or to adjust the volume excepting DVD mode. System: Press repeatedly to cycle through the system options: AUTO and NTSC3.58. (This button is inactive for TV, VGA, COMPONENT input source.) Source: Press to select the signal source, such as TV, AV, S-Video, Component, DVD or VGA. Sleep: Press repeatedly until it displays the time in minutes (5 Min, 10 Min, 15 Min, 30 Min, 60 Min, 90 Min, 120 Min and, OFF) that you want the TV to remain on before shutting off. To cancel sleep time, press Sleep button repeatedly until sleep OFF appears. Display: Press to display the channel information and it disappear after 3 seconds. Play/Pause: Press to play or pause the DVD disc. Stop: Press to stop playing the disc. Angle: Press to select desired viewing angle of the Video (disc feature). Open/Close: Press to open or close the disc tray. Skip+/-: Press to skip the forward or backward. Search+/- : Press to search the forward or backward. DVD Menu: Press to return DVD disc menu. (Continued on next page) 14 DVD Info: Press to display DVD information. Setup: Press to display a menu. Press it again to exit menu. Repeat: Press repeatedly to cycle through the options: CHAPTER, TITLE, ALL and nothing. Audio: Press to select desired audio track. Prog: Press to display the program menu. Press it again to exit. Sub. title: Press to select desired DVD subtitle. Title: Press to display to DVD disc title. Note: Press Ch / on the remote control can turn on TV set from last preview mode. Note: Press Ch / on the remote control can turn on TV set from standby mode. Insertion of Batteries: - Turn the remote control upside down, press and slide off the battery cover. - Insert two 1.5V (AA) batteries into the compartment, take care to observe the and markings indicated inside. - Replace the cover and slide in reverse until the lock snaps. 15 Range of Remote Control Sketch map 20° 20° 30° 30° - Ensure the remote control is pointed towards the remote control window on the display unit. - No obstacles should be placed between the remote control and the remote control window. - The effective receiving range for the signal is within 5-8 meters from the front of the remote control window, and 30° to the left or right side and 20° above or below the control window. Care For Remote Control - Avoid spilling liquids on the remote. - Avoid dropping or otherwise jarring the remote. - Always store the remote control at dry and normal room temperature place. - If the remote is nor performing satisfactorily, replace the batteries. The batteries should be replaced after one year. - If the remote control will be idled for a long time (above 1 month) take out the batteries to avoid leakage from the batteries. - Clean up the entire remote control especially the battery compartment if any leakage found. - Do not mix using different kind of new and used batteries together to avoid leakage. 16 5. Connect Accessory Devices Connecting a DVD player or other equipment Switch off LCD TV and external equipment before connecting cables. 1. Connect a DVD player or other equipment's Component Video Out (Y,Pb,Pr) to the LCD TV's corresponding Component In (Y,Pb,Pr) jacks. 2. Connect a DVD player's Audio Out to the TV Component L/R jacks. 3. Press Power to turn on the LCD TV. Turn on external equipment also. 4. Press Source to select COMPONENT signal source. Green Red Blue Red White DVD or Set-top box Connecting the Computer Switch off LCD TV and external equipment before connecting cables. 1. Connect a computer's VGA Out to the LCD TV's VGA In jacks. 2. Connect a computer's Audio Out to the LCD TV's Audio In jack. 3. Press Power to turn on the LCD TV. Turn on external equipment also. 4. Press Source to select VGA signal source. 17 Connecting the DVD or VCR player devices Switch off LCD TV and external equipment before connecting cables. 1. Connect a DVD or VCR player's Video Out to the LCD TV's Video In jack by a Video cable. 2. Connect a DVD or VCR player's S-VIDEO Out to the LCD TV's S-VIDEO In jack by a S-VIDEO cable. 3. Connect a DVD or VCR player's Audio Out to the LCD TV's L/R jacks by a Audio cable, in this stage, the S-VIDEO and VIDEO is sharing this L/R Audio in channels. 4. Press Power to turn on the LCD TV. Turn on external equipment also. 5. Press Source to select AV or S-VIDEO signal source. Yellow White Red DVD or VCR player DVD or VCR player Connect audio amplifier or other TV set Switch off LCD TV and external equipment before connecting cables. 1. Connect the LCD TV Audio Out (R/L) to the audio amplifier In (R/L). 2. Press Power button to turn on the LCD TV. Turn on external equipment also. White Red Audio Amplifier 18 Connect audio amplifier Switch off LCD TV and external equipment before connecting cables. 1. Connect the LCD TV-combo's COAXIAL OUT to the Audio Amplifier COAXIAL Input jack by a coaxial cable. 2. Press Power to turn on the LCD TV-combo. Turn on external equipment also. 3. Press Source to select DVD signal source, and set the Audio Amplifier to coaxial input mode. 4. When DVD is playing, you can enjoy coaxial digital audio by Audio Amplifier. Insert the Disc to slot-in DVD Player 1. Press Source button to select DVD signal source. 2. Insert a disc into the slot-in DVD Player's disc tray, please confirm the disc's screen is face to us. 3. The DVD Play will auto slot in the disc, and the LCD TV will display "Loading", if the disc type is fit the spec, you can enjoy the playing. Note: Please be noted that the disc's contents must be in front, if you put it in reverse, the LCD TV screen will display "No Disc". Disc's screen side Connecting directly to cable or an antenna When using 75 coaxial Aerial: Connect directly to the RF terminal of the tuner. VHF Antenna 1m above UHF Antenna Special Antenna Mixer 75 Coaxial Aerial RF(VHF/UHF) terminal 19 6. Basic Operation - Press the Power on the remote control or on the control panel to turn on the unit. The power indicator changes from red to green. - Press the Power on the remote control or on the control panel again to return the display to standby mode. The power indicator changes from green to red. Note: For protecting your LCD TV product, the interval time between turn on the LCD TV product and shut down it should be kept at least one minute. 6.1 Power ON/OFF: The Display is in Standby mode Power Favorite Add/Earse Zoom Recall 6.2 Selection of Input Mode - Press SOURCE on the remote control or on the LCD TV control panel to select the signal source you desired. When no input from the selected signal source, "Main no signal" and blue background will appear, press Source on the remote control or on the control panel again to search the next source. Freeze , Enter Source Display Note: The LCD-TV will automatically turn itself off after approximately 15 minutes if no signal input. When no signal is inputted for about 14 minutes. A "No signal and going to power down" wording will appear. You can press " " or " " button to selected, press "ENTER" to confirm. If select "Cancel" or no operation, the LCD-TV will automatically turn off after 1 minutes, if select "OK", it will turn off immediately. In DVD mode, if no disc playing for about 5 minutes, there is a screensaver as big DVD logo run and change color continuously. 6.3 Other Function - Freeze: Press it to hold the current video and press again to cancel and return to normal viewing. Zoom : Press it repeatedly the size of image will change cycling in following sequence: 2 times 4 times 8 times 1/8 times 1/4 times 1/2 times normal. Display: Press once to display the information as following, and disappear after 3 second; When in TV mode 68 - When in VGA mode VGA 1280 x 1024 60Hz - 20 6.4 Using the POP double-window feature The POP (picture-out-picture) feature splits the screen into a double window that allows you to watch two programs at the same time. The POP program can come from a TV broadcast or an external source, such as a VCR. To display a TV broadcast in the POP window: 1. Press PIP button to enter the POP window. Press PIP button for selecting the different PIP modes, such as following; Normal Picture PIP Basic PIP Mode LR POP Mode button to select the window Use / and active it with a red-colored frame. Press Source button to select the input source for the POP window. Source 2. To change the next programmed channels, press number buttons (0~9) or Ch / button. Note: a. If the V-CHIP feature is active and you try to watch a TV program that exceeds your set rating limits, the program will be blocked. b. For active window, you can change channels, adjust volume, select input source ect.. After power off, the active window will be keep the setting when you power on next time. c. It is must to have second video source connected for basic PIP and L/R POP modes. d. After you choose the POP mode, all settings are only aimed at the active window. e. In POP mode, the DVD menu and other operation are invalid. (Continued on next page) 21 To display a picture from an external source in the POP window: 1. 2. 3. 4. Connect the external source equipment. (refer to Connect Accessory Devices page). Select the TV program you want to watch in the main window. Press PIP to display the POP window. Repeatedly press Source button to select the input source for the POP window. To change the PIP picture size: Press PIP. Size button to select the PIP picture size, such as: Small, Middle, Large. To change the PIP position: Press PIP. Pos button to change the PIP window position under PIP mode, it display as following; Right Down Left Down Left Up Right Up Right Down PIP. Size PIP. Pos Left Up Right Up Left Down Right Down Switching the pictures: Enter When in Basic PIP mode, press "Enter" to swap main or sub pictures; When in LR POP mode, press "Enter" swap the L/R pictures. When the red frame is displaying in main window, the sound goes out of main window source. If it display in sub window, the sound goes out of sub window source. To change Main or Sub sound: 6.5 OSD Option Adjustment Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the LCD V using the menu system. You can access the menu using the buttons on your LCD TV or remote control. The OSD menu displayed in the following sequence (circular display): Video Audio Misc TV Geometric (Continued on next page) 22 Press Menu button to display the menu system. Press or button to select a menu. Press or button to select an item. Press Enter button on the remote control or Source button on the side panel to activate the function settings in the menu. Press , , or button to select or adjust a setting, press Enter button to confirm. If you do not make a selection within 15 seconds, the main menu closes automatically; the other menus close automatically within 6 seconds. Press button to return OSD-menu. To close an on-screen menu instantly, press Menu button on the remote control or MENU button on the side panel. Menu Enter Source The Side Panel MENU SOURCE 6.6 OSD Functions of TV System 1 Using the Video Menu Option Contrast Brightness Back Light Saturation Hue Sharpness Phase Color Temperature Advanced Picture Adjust Note: Press / 0~100 0~100 Bright, Middle, Dark 0~100 -30~+30 0~7 0~31 Cool, Middle, Warm, User Description Reduce/Enhance Darken/Brighten Adjust the balance of back light Decrease/Increase of color Decrease/Increase Soften/Sharpen Decrease/Increase Adjust the balance of whitening Adjust the picture effect Video Menu is just for TV, AV, S-Video, Component, DVD input source mode. It is not available in other input source mode. When smart picture mode is pre-set, the value of the above settings will be different according to different input source. (Continued on next page) 23 Adjustment of "Contrast" Press Menu button on the remote control, and then press or until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease that will soften the color. Press that will make white area more bright. Press Enter button to confirm the adjustment and return. button to increase Adjustment of "Brightness" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease. Press button to increase that will brighten the dark area for seeing the objects in shadowness more clear. Press Enter button to confirm the adjustment and return. 24 Adjustment of "Back Light" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button and then press or button to select one of "Bright", "Middle" or "Dark" for the balance of back light. Press Enter button to confirm the adjustment. Press button to return. Adjustment of "Saturation" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease. Press button to increase that will make color more intensive. Press Enter button to confirm the adjustment and return. 25 Adjustment of "Hue" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease that will make image more green. Press increase that will make image more red. Press Enter button to confirm the adjustment and return. button to Adjustment of "Sharpness" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press or button to increase or decrease that will make image with more sharp edge. Press Enter button to confirm the adjustment and return. 26 Selection of "Phase" setting Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease. Press button to increase. Press Enter button to confirm the adjustment and return. Note: This is a feature just used for YPbPr input source. Selection of "Color Temperature" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to select one of "Cool", "Middle", "Warm" or "User" for balance of whitening. Press Enter button to confirm the selection. Press button to return. (Continued on next page) 27 If you select the item of "User", a status bar below comes up for you to adjust the color temperature to you desirable value. Selection of "Advance Picture Adjust" Press Menu button, and then press or button until the "Video" menu appears. Press or button to highlight the item. Press Enter button to confirm for sub-selection as shown in the table below. Table of Auto Adjustment Setting Item DNR White Peak Limitator CTI Flesh Tone Adaptive Luma Control Description Selecting to control the Off, Low, Middle,Strong sharpness and noise reduction. Select "On" to limit the On, Off white peak. Low, Middle, Strong, Select dynamic color Off improve level. Select "On" to correct On, Off the flash tone automatically. Selecting to control the On, Off lum. Status Press Enter button to confirm the selection. Press button to return. 28 2 Using the Audio Menu Option Bass Treble Balance Surround Press 0~100 0~100 -20~+20 On, Off / Description Decrease/Increase Decrease/Increase Emphasize left/right speaker Note: Audio Menu can be adjusted only if sound is in USER mode. Adjustment of "Bass" Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease the Bass sound. Press Press Enter button to confirm and return. button to increase it. Adjustment of "Treble" (Continued on next page) 29 Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease the treble sound, press Press Enter button to confirm and return. button to increase it. Adjustment of "Balance" Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to emphasize the left speaker. Press right speaker. Press Enter button to confirm and return. button to emphasize the Selection of "Surround" Press Menu button, and then press or button until the "Audio" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to select "On" or "Off". Press "Enter" to confirm your selection. Press button to return. 30 3 Using the Miscellaneous Menu Option Language Closed Caption V-Chip Parental Blue Mute Default Press / Description English, Français, Select the OSD language Español C1, C2, C3, C4, T1, To select Captions or Text T2, T3, T4, Off Enter to V-Chip function Enter to Parental function Select it to set screen to On, Off pleasant blue background Select to restore factory default settings. Selection of "Language" Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to choose the OSD language. Press Enter button to confirm your selection. Press button to return. Selection of "Closed Caption" (Continued on next page) 31 The closed caption features has two options: Adjustment only for TV, AV, S-VIDEO input signal. · Captions: An on-screen display of the dialogue, narration, and sound effects of the TV programs and videos that are closed captioned (usually marked as "C/C" in TV listings. · Text : An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations). To view captions or text: Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or to choose one of "C1", "C2", "C3", "C4", "T1", "T2", "T3", "T4", as follows: · To view captions, highlight C1, C2, C3, or C4 (C1 displays translation of the primary language in your area). Trees near the church. Note: If the program or video you selected is not closed captioned, no captions will display on-screen. · To view text, highlight T1, T2, T3, or T4. World Weather New York London HongKong F 53 51 80 Temp C 12 11 25 Current Weather Sunny Cloudy Clear Note: If text is not available in your area, a black rectangle may appear on-screen. If this happens, turn off the Closed Caption feature. Note: A closed caption signal may not display in the following situations: when a videotape has been dubbed when the signal reception is weak when the signal reception is nonstandard Select "Off" to close this function. Press Enter button to confirm your selection. Press button to return. Hot keys: - You can also press CCD button on the remote control to enter Closed Caption menu. 32 Setting of "V-Chip" Some programs and movies include signals that classify the content of the program (dialog, language, sex, violence). The "V-Chip" control feature in this detects the signals and blocks the programs according to your selections. To use this feature, perform the following setup. Adjustment only for TV, AV, S-VIDEO input signal. Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. The "V-Chip" menu includes the "V-Chip Control", "Block MPAA Rating", and "Block TV Rating" functions. You can use these functions after entering the correct PIN code. Entering the PIN code Blocking Reset status: Set your 4-digit code by pressing the Number buttons (0~9), and then press Enter. When the PIN code is already stored: Press the Number buttons (0~9) to enter the 4-digit PIN code used for blocking channels, and then press Enter. Note: The initial password for the system is "0000". If you had forgotten the password, please contact with service centre. If the input is invalid, a message will pop up as below; (Continued on next page) 33 You can press Enter button to display "Input Your Password Please" menu again, then entering the PIN code, or press , , or button move cursor to "Cancel" and press Enter button to close up this menu. Using the "V-Chip Control" item When enter the "V-CHIP" menu, select "V-Chip Control". Press or button to highlight the "V-Chip Control" item. Press Enter button to confirm and then press or button to select "ON" or "OFF". ON : TV Blocking and MPAA Blocking are activate. OFF : TV Blocking and MPAA Blocking are not activate. Press button to return or press Menu button to exit. Using the "Block MPAA Rating" item When enter the "V-CHIP" menu, select "Block MPAA Rating". Press or button to highlight the "Block MPAA Rating" item. Press Enter button to confirm. Press or button to select an item, then press Enter button to lock (display " ") or unlock (display " "). (Continued on next page) 34 The movie block you can lock are described as follows: Item G PG PG-13 R NC-17 X Description and Content themes General Audience (Appropriate for all ages) Parental Guidance Suggested (Some material may not be suitable for children) Parents Strongly Cautioned (Some material may be inappropriate for children under 13) Restricted (Under 17 requires accompanying parent or adult guardian) Not intended for anyone 17 and under X-rated (For adults only) Press Menu button to exit the sub-menu. Using the "Block TV Rating" item From the "V-CHIP" menu, select "Block TV Rating". Press or button to highlight the "Block TV Rating" item. Press Enter button to confirm. Press , , or button to select an item, then press Enter button to lock (display " ") or unlock (display " "). (Continued on next page) 35 The aged-based TV Guideline and content themes you can lock are listed as follows: Item TV-Y TV-Y7 Description and Content themes All Children (This program is designed to be appropriate for all children.) Directed to Older Children (This program is designed for children age 7 and above. Note: Programs in which fantasy violence may be more intense or more combative than other programs in this category are designed TV-Y7.) General Audience (Most parents would find this program suitable for all ages.) Parental Guidance Suggested (This program contains material that parents may find unsuitable for younger children.) D) Some suggestive dialog L) Infrequent coarse language S) Some sexual situations V) Moderate violence Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14 years of age.) D) Intensely suggestive dialog L) Strong, coarse language S) Intense sexual situations V) Intense violence Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for children under 17.) L) Crude or indecent language S) Explicit sexual activity V) Graphic violence TV-G TV-PG TV-14 TV-MA Press Menu button to exit the sub-menu. Unlocking programs temporarily If you try to watch a TV program that exceeds the TV Guideline you set, the TV enters program lock mode. You can either unlock the program temporarily or select a non-locked program to watch, press or button to select the program. To temporarily unlock the program, press the Number buttons (0~9) to enter your 4digit PIN code. V-CHIP BLOCK TV-PG LV Enter Password If the correct code is entered, the program lock mode is released and the normal picture appears. Hot keys: - You can also press V-CHIP button on the remote control to enter V-Chip menu. 36 Setting of "Parental" The TV programs and movies shown on TV are given a rating signal based on the following rating systems. To block programs you feel unsuitable for your children, you need to set the TV for the desired rating systems. The TV's "Parental" control feature functions by receiving the rating signal from your local broadcasting station or cable service provider. Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. The "Parental" menu includes the "Channel Lock", "Video Lock", "Change Password" and "Clear All" functions. You can use these functions after entering the correct PIN code. Entering the PIN code Blocking Reset status: Set your 4-digit code by pressing the Number buttons (0~9), and then press Enter. When the PIN code is already stored: Press the Number buttons (0~9) to enter the 4-digit PIN code used for blocking channels, and then press Enter. Note: The initial password for the system is "0000". If you had forgotten the password, please contact with service centre. If the input is invalid, a message will pop up as below; (Continued on next page) 37 You can press Enter button to display "Input Your Password Please" menu again, then entering the PIN code, or press , , or button move cursor to "Cancel" and press Enter button to close up this menu. Press or button to choose an item as below table showing. Press Enter button to confirm. Press button to return. Table of Parental Setting Status Description Use the Ch / and Enter All channels buttons to select the channel you desired to lock. Use Source and Enter buttons TV1, AV, S-Video, to select the Video you desired to Component, DVD, lock. VGA Enter a new 4-digit code by using the number keys on the remote, and then confirm the new code by entering it a second time, You will get a confirmation message when your code has been successfully changed. Press Enter button to clear all present Parental setting. Items Channel Lock Video Lock Change Password Clear All 38 Selection of "Blue Mute" Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to choose "On" or "Off", when select "On" to set screen to a pleasant blue background when it detects no signal available if turn on. Press Enter button to confirm your selection. Press button to return. Using "Default" Press Menu button, and then press or button until the "Misc" menu appears. Press or button to highlight the item. Press Enter button to confirm, it will reset to restore factory default settings. After that, a confirmation message will pop up. Note: Just reset the items in the setup menu don't include the protected-items(Needs pin code enter, such as password, video lock, and channel lock) and properties such as skipped channel, channel name. 39 4 Using the TV Menu Option Auto Search Tuner Mode Channel Skip Channel Name Note: Press Cable, Air / Description To searching the channel To select the tuner mode To skip the channel Add the channel name TV menu is only for TV input source mode, thus it is not available in other input source mode. The locked channel will be skipped during the searching. Using the "Auto Search" Press Menu button, and then press or Press or button to highlight the item. Press Enter button to confirm. Press button to return. button until the "TV" menu appears. Using the "Tuner Mode" (Continued on next page) 40 Press Menu button, and then press or button until the "TV" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to choose "Air" or "Cable". Press Enter button to confirm. Press button to return. Using the "Channel Skip" Press Menu button, and then press or button until the "TV" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press or button to scan which channel is skipped, there is a the channel. Press Enter button to toggle the channel will be skipped or not. Press button to return. Using the "Channel Name" Press Menu button, and then press or button until the "TV" menu appears. Press or button to highlight the item. Press Enter button to confirm, it will display "Channel Name" list. Use , , or button for select, and move cursor to "OK", then press Enter button for confirm you selection. If you want to cancel this operation, move cursor to "Cancel" and press Enter button for close this setting. Press button to return. Note: It will be invalid if the current source is not TV. 41 5 Using the Geometric Menu Option Contrast Brightness Back Light Auto Setting Phase Manual Clock Display Adjustment Note: 0~31 0~255 Vertical position, Horizontal position Press / 0~100 0~100 Middle, Bright, Dark Description Reduce/Enhance Darken/Brighten Adjust the balance of back light To adjust the position of display automatically Soften/Sharpen Decrease/Increase To adjust the position of display If your current input source is "VGA" , push Menu button enter into this menu. It is not available in other input source mode. Contrast, Brightness can be adjusted only if picture mode is in USER mode. When smart picture mode is pre-set, the value of the above settings will be different according to different input source. Using "Contrast" Press Menu button on the remote control, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease that will soften the color. Press that will make white area more bright. Press Enter button to confirm the adjustment and return. button to increase Using "Brightness" (Continued on next page) 42 Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease. Press button to increase that will brighten the dark area for seeing the objects in shadowness more clear. Press Enter button to confirm the adjustment and return. Using "Back Light" Press Menu button , and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press or button to select one of "Bright", "Middle" or "Dark" for the balance of back light. Press Enter button to confirm the adjustment. Press button to return. Using "Auto Setting" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm. Press button to return. Note: This item will auto-adjust the picture display. (Continued on next page) 43 Using "Phase" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease and press button to increase it. Press Enter button to confirm and return. Using "Manual Clock" (Continued on next page) 44 Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm and display a status bar as below. Press button to decrease the menu clock. Press Press Enter button to confirm and return. button to increase it. Using "Display Adjustment" Press Menu button, and then press or button until the "Geometric" menu appears. Press or button to highlight the item. Press Enter button to confirm for sub-selection as shown in the table below. Press Enter button to confirm your selection. Press button to return. Table of Display Adjustment Items Vertical Position Horizontal Position Description Use " " or " " to select it and press "ENTER" to confirm. Use " " or " " to move the image up or down. Use " " or " " to select it and press "ENTER" to confirm. Use " " or " " to move the image left or right. Selecting Channel Press Ch / button on the remote control to search the channels, the channel number will increase or decrease by 1 for each pressing excluding the skipped channels. Press number buttons 0~9 to select the corresponding channel content. If the channel number is bigger than 9, just press the two number buttons successively. If the channel number is bigger than 100, just press the three number buttons successively. The time interval should not exceed 2 seconds. If the channel number you pressed is bigger than the maximum channel number that the setting is permitted, the maximum numbered channel content will be remained. Channel Preview Press Recall button to switch between present channel and previous channel. (Only for TV) 45 6.7 Operation of DVD System 1 Suit Table Disc Types This player is compatible to the following disc types: - DVD single sided / double sided single layered / double layered - CD - CD-R / CD-RW No-play disc The following discs are NOT acceptable by the DVD player: - DVD disc with region code that does not match the player's region code (Check the disc's region code printed on the disc packing. Region code "ALL" will be acceptable by all players.) - Some DVD discs that were purchased outside the application country. - PC application on CD-R/CD-RW. - CD-ROM for PC interface only. NOTE: Some PC application files on CD-R or CD-RW CANNOT be accepted by the unit, e.g. CD-ROM under PC Windows, etc. (CD-R / CD-RW writing format may be different, some discs are not acceptable) 2 Play a Disc Switch on the player Push the main power button to turn on the product, press Source button to select DVD signal. Load a disc Play/ Pause Open/ Close DVD Menu OPEN/ CLOSE PLAY/ PAUSE Press OPEN/CLOSE button on the remote control (or side panel) to open the disc tray. Load a disc and will auto solt-in to the disc tray. Automatic Play The unit will take a few seconds to download the disc initial data, display the disc type logo in the left upper corner of the TV screen, and then start playing automatically. If a DVD Disc Menu appears on screen Press PLAY/PAUSE button on the remote (or side panel) to start playing. [Press , , , buttons to select the desired feature in the menu, and then press the Enter button to confirm a selection.] 46 Press OPEN/CLOSE button on the remote control (or side panel) to open the disc tray. Load a disc and will auto solt-in to the disc tray. Automatic Play The unit will take a few seconds to download the disc initial data, display the disc type logo in the left upper corner of the TV screen, and then start playing automatically. If a DVD Disc Menu appears on screen Press PLAY/PAUSE button on the remote (or side panel) to start playing. [Press , , , buttons to select the desired feature in the menu, and then press the Enter button to confirm a selection.] Note: Normally, when a MP3 disc is loaded, the unit will take longer time to download the initial data. DVD disc that does not match the region code cannot be executed by this player. Return to the disc main menu, press DVD Menu button on the remote control. Prevent loading the disc upside down. The DVD work only on DVD source, in other source, the DVD Player does not work. 3 Function Buttons Open / Close disc tray Press OPEN/CLOSE button on the remote control (or side panel) to open or close the disc tray. The disc will auto solt-in to the disc tray. Play / Pause / Step/ Stop Play/ Search+/Press PLAY/PAUSE button on the remote Pause (or side panel) to start playing. Press PLAY/PAUSE button again on the Stop remote (or side panel) to pause. Skip+/Repeat pressing the button to step forward the still picture frame by frame. DVD Menu Press PLAY/PAUSE to resume normal playback. Press Stop button to stop in two modes: Title - Press once: Stop memorizes the interrupt position. (May resume with PLAY/PAUSE button) - Press twice: To stop completely. (Will not resume with PLAY/PAUSE button) Skip Forward / Backward Press Skip+ button to skip forward (chapters or CD tracks). Press Skip- button to skip backward (chapters or CD tracks). Note: Player will not advance or reverse during "WARNING" section of any disc. Skip Forward/Backward function will jump to next/previous page in Picture CD mode. 47 Search Forward / Backward Press Search+ button to search forward Repeat pressing the button to change search speed. Press Search- button to search backward Repeat pressing the button to change search speed. Press Play/Pause button to resume Normal playback Note: Player will not advance or reverse during "WARNING" section of any disc. Disc Title / Menu Press DVD Menu button return to the DVD disc Menu. Press Title button return to the DVD disc Title. Note: Disc menu is a DVD disc feature, allowing users to select functions on screen. Disc title is the beginning track of a DVD disc. Some DVD discs refuse the "TITLE" function. Repeat Press Repeat button multiple times to reach desired repeat mode (see below). DVD disc Chapter: Repeat the Chapter Title: Repeat the Title All: Repeat whole disc CD disc Off: Repeat function off Repeat One: Repeat the existing track Repeat Folder: Repeat the existing folder MP3 disc Repeat Single: Play the existing track once Repeat One: Repeat the existing track Repeat Folder: Repeat the existing folder Folder: Play the existing folder once Note: Repeat functionality depends on different disc's production format, some DVD discs do not allow repeat function. 48 Multi-Angle If a DVD disc contains Multi-Angle feature, viewing angles may be selected: During in playback, repeat pressing Angle button to select the desired viewing angle. Status will be displayed on screen. Multi-Subtitle If a DVD disc contains the Multi-Subtitle feature, subtitle may be selected: button to select the desired subtitle. Status will be displayed on screen. During in playback, repeat pressing Sub. title Angle DVD Info Audio Sub. title Note: A DVD disc may contain up to 32 subtitle selections. Multi-Audio Sound track If a DVD disc contains Multi-Audio Sound track feature, Audio Language can be selected: During in playback, repeat pressing Audio button to select the desired audio language. Playback status will be displayed on screen. A CD disc contains two channels stereo sound tracks, Left and Right. The function can change to Left and Right channel mono output in DOWN MIX audio mode. Note: A DVD disc may contain up to 8 audio language selections. In most cases, an Audio Sound track selection will be displayed on a DVD disc start up menu. Press , , , buttons to select and Enter button to confirm. DVD INFO Press the DVD Info button to display as below: The First Time: Display the Title Elapsed contents on screen. The Second Time: Display the Title Remain contents on screen. The Third Time: Display the Chapter Elapsed contents on screen. The Fourth Time: Display the Chapter Remain contents on screen. 49