User manual ALCATEL-LUCENT SPEEDTOUCH 605S

SpeedTouchTM605s Business SHDSL Router Setup and User's Guide Release R4.2 600 SERIES SpeedTouchTM605s Setup and User's Guide Release R4.2 Status Change Note Short Title Copyright v1.0 PeckelbeenS Setup and User's Guide ST605s R4.2 (en) © 2003 THOMSON. All rights reserved. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Contents 1 1.1 1.2 1.3 1.3.1 1.3.2 1.4 SpeedTouchTM Installation ............................................ 3 Getting Acquainted with the SpeedTouchTM.................................................... 4 Setting up the SpeedTouchTM............................................................................. 6 SpeedTouchTM Configuration Setup .................................................................. 7 Configuration Setup for Microsoft Windows Operating Systems ........................................ 8 Configuration Setup for other Operating Systems................................................................. 14 Dr SpeedTouchTM Installation .......................................................................... 17 2 2.1 2.2 2.2.1 2.2.2 2.3 2.3.1 2.3.2 SpeedTouchTM Internet Connectivity ........................ 21 Surfing the Internet ........................................................................................... 22 Connect to the Internet via SpeedTouchTM's embedded PPP client. .......... 23 Internet Sessions via Windows XP's UPnP .............................................................................. 24 Internet Sessions via the SpeedTouchTM Web Pages (all OSs)............................................ 25 Connect to the Internet via a Broadband Dial-in Client ............................... 26 Using the Windows XP Dial-in Client....................................................................................... 27 Using the Mac OS X Dial-in Client............................................................................................. 30 3 3.1 3.2 SpeedTouchTM Web Interface..................................... 31 Basic Topics Menu Links ................................................................................... 34 Advanced Topics Menu Links ........................................................................... 37 1 4 SpeedTouchTM NAPT Manager .................................. 51 5 5.1 5.2 SpeedTouchTM System Software Upgrade ................ 57 The SpeedTouchTM Upgrade Wizard .............................................................. 58 Manual System Software Management via BOOTP Server ......................... 62 6 6.1 6.2 Troubleshooting ........................................................... 65 General................................................................................................................ 66 SpeedTouchTM Default Configuration.............................................................. 67 2 1 SpeedTouchTM Installation 1 SpeedTouchTM Installation Introduction Thank you for purchasing the SpeedTouchTM605s Business SHDSL Router! With the SpeedTouchTM605s Business Symmetrical High speed Digital Subscriber Line (SHDSL) Router, surfing the Internet will become a whole new experience. This User's Guide will assist you in getting acquainted with the SpeedTouchTM605s Business SHDSL Router and in getting connected quickly to the Internet. Generally, the SpeedTouchTM605s will be referred to as SpeedTouchTM in this Setup and User's Guide unless specifically indicated. Before connecting the SpeedTouchTM, read the SpeedTouchTM Quick Installation Guide and Safety Instructions. The SpeedTouchTM605s is a Universal Plug and Play (UPnP) certified product. UPnP enables your computer to discover and control UPnP devices on the network. Note For more information about how to install UPnP on your computer please consult your operating system's user's guide. In this Setup and User's Guide Terminology Safety instructions UPnP Documentation and software updates The SpeedTouchTM605s product continues to evolve as extra and new functionalities are made available. For more information on the latest technological innovations, software upgrades, and documents, please visit the SpeedTouchTM web site at: www.speedtouch.com E-SIT-CTC-20030605-0003 v1.0 3 1 SpeedTouchTM Installation 1.1 Getting Acquainted with the SpeedTouchTM Introducing the SpeedTouchTM Prior to proceeding, please make sure to read the SpeedTouchTMQuick Installation Guide first. It provides important package content and safety information. Check whether all items are present in your package. In the event of damaged or missing items, please contact your local product dealer for further information. Front and back panel layout The SpeedTouchTM605s Business SHDSL Router is presented in a slim line housing: The device is equipped with a single 10/100Base-T Half-/Full-duplex MDI-X Ethernet port: Power Switch Reset DSL Line Port Power Socket 10/100Base-T Ethernet port Front panel LEDs The SpeedTouchTM605s Business SHDSL Router is equipped with five LEDs on its front panel, indicating the state of the device during normal operation: Indicator Name LAN Color Green State Flashing Off Line TX Green Flashing Off Line RX Green Flashing Off Line Sync Green Off Flashing On Ethernet LAN activity No Ethernet LAN activity ATM cell transmission on DSL line No transmission activity ATM cell reception on DSL line No reception activity No SHDSL line Initialization of SHDSL line SHDSL line synchronized Description 4 E-SIT-CTC-20030605-0003 v1.0 1 SpeedTouchTM Installation Indicator Name PWR/Alarm Color Green State Flashing On Orange Red On Flashing On Description Back-to-defaults Power on, normal operation Self test Power on Power on, selftest failed Ethernet port(s) LEDs The Ethernet port on the rear panel has one LED: Link Integrity/Activity LED 10/100Base -T Indicator Name Integrity/Activity Color Green State Off On Flashing Description No connection on this port Ethernet link up. No activity Activity on this Ethernet port DSL Port Service 2-wire SHDSL Port pinning 3/4 DSL service The appropriate SHDSL service must be available at your local premises. E-SIT-CTC-20030605-0003 v1.0 5 1 SpeedTouchTM Installation 1.2 Setting up the SpeedTouchTM Local network For Ethernet connectivity you need at least: · · Ethernet Cables A computer with installed Ethernet Network Interface Card (NIC) or available on-board Ethernet port If needed, a hub or switch and the necessary connection cables In the SpeedTouchTM605s box, a full wired Cat.5 straight-through RJ45/RJ45 Ethernet cable, further referred to as LAN cable is included. You can use LAN cables other than the one provided in the box. However make sure to use correct connection cables. Wiring procedure Proceed as follows: 1 2 3 Use the included LAN cable to wire your computer's Ethernet port to the SpeedTouchTM605s Ethernet port. Use the included DSL cable to wire the SpeedTouchTM605s's Line port to your telephone wall outlet. Plug the power adapter's coaxial jack into the SpeedTouchTM605s DC inlet and plug the power adapter in a wall outlet. Note Always check first whether the included power adapter suits the local power specifications. More information on Ethernet wiring PC wiring For more information, see the application note "The SpeedTouchTM and Ethernet Connectivity". Once all connections are made, the result should look similar as below: 6 E-SIT-CTC-20030605-0003 v1.0 1 SpeedTouchTM Installation 1.3 SpeedTouchTM Configuration Setup Internet connectivity Some configuration may be required to prepare the SpeedTouchTM for Internet connectivity. You might need a user account with an Internet Service Provider (ISP) for Internet access. For this user account, your ISP will provide you with: · · A user name (logon ID) A password What you need from your ISP Other information may be required, depending on the ISP's specific requirements. Configuration of the SpeedTouchTM Depending on your computer's Operating System (OS) the configuration of your Internet connectivity can be done automatically or manually. If your computer runs: · A Microsoft Windows OS. The SpeedTouchTM Setup wizard, included on the SpeedTouchTM Setup CD-ROM, will automatically guide you through the configuration of both the SpeedTouchTM and your PC for setting up the appropriate configuration. Proceed with "1.3.1 Configuration Setup for Microsoft Windows Operating Systems" on page 8. · Another OS, e.g. Mac OS, Unix, Linux. The SpeedTouchTM Embedded Easy Setup wizard, accessible from the SpeedTouchTM web pages, will automatically guide you through the configuration of the SpeedTouchTM. Proceed with "1.3.2 Configuration Setup for other Operating Systems" on page 14. E-SIT-CTC-20030605-0003 v1.0 7 1 SpeedTouchTM Installation 1.3.1 Configuration Setup for Microsoft Windows Operating Systems Microsoft Windows One of the following Windows operating systems must be installed on your PC(s): · · · · · · Windows 98 Windows 98SE Windows ME Windows NT4.0 SP6 Windows 2000 Windows XP You may need the Windows installation CD-ROM during installation. The SpeedTouchTM Setup wizard The SpeedTouchTM Setup wizard procedure consists of two major parts: · · The detection procedure The configuration procedure 8 E-SIT-CTC-20030605-0003 v1.0 1 SpeedTouchTM Installation The detection procedure The detection procedure proceeds as follows: 1 Insert the SpeedTouchTM Setup CD-ROM in your PC's CD-ROM drive. The SpeedTouchTM CD Browser will start automatically. Note If the SpeedTouchTM CD Browser window does not appear automatically, open a Run window via Start > Run from the Start menu and enter the following path: D:\Menu.exe, where D stands for the drive letter of your CD-ROM drive. 2 The Choose Language window prompts you to select a language: Select the language of your choice and click OK. 3 The SpeedTouchTM CD Browser appears: Click Initial Setup. 4 The Setup and Installation window appears: To start the SpeedTouchTM Setup wizard, click Setup my SpeedTouchTM. E-SIT-CTC-20030605-0003 v1.0 9 1 SpeedTouchTM Installation 5 The Welcome to the SpeedTouchTM Setup Wizard window appears: Click Next to proceed. 6 The Software License Agreement window appears: You must accept before continuing. Therefor click Yes to accept. Note 7 If you have already accepted this License Agreement in a previous configuration setup, this window will not be shown. The Setup wizard will continue to search for the SpeedTouchTM on the network. The following window shows the detection progress: 10 E-SIT-CTC-20030605-0003 v1.0 1 SpeedTouchTM Installation 8 The Setup wizard should find your SpeedTouchTM device on the local network. This is indicated by the following window: In case more than one SpeedTouchTM device is found, a listing is provided from which you can select your SpeedTouchTM. Note If the Setup wizard does not find any SpeedTouchTM on the network an error window pops up. In this case check: · · · Whether the SpeedTouchTM is turned on and fully initialized. Whether your PC is correctly connected to the SpeedTouchTM and has a valid IP address (i.e. any IP address but 0.0.0.0). Whether no dedicated firewall device or router is placed between your PC and the SpeedTouchTM and whether no personal firewall software is running on your PC. To repeat the search for the SpeedTouchTM, click Back and proceed with step 7 of this procedure. 9 To continue with the configuration of your SpeedTouchTM and your PC, proceed with the configuration procedure described below. E-SIT-CTC-20030605-0003 v1.0 11 1 SpeedTouchTM Installation The configuration procedure The Configuration procedure proceeds as follows: 1 Once the SpeedTouchTM Setup wizard has detected your SpeedTouchTM device, you can proceed with the configuration procedure. If more than one SpeedTouchTM device is listed, select the appropriate one. Then, click Next to proceed. Note If the SpeedTouchTM has been configured before, it may be protected by a system password. You must provide user name and system password before you can view the device details or continue with the configuration. 2 You will be asked to choose between reconfiguring your SpeedTouchTM or changing your Local Area Network configuration. Select Reconfigure the SpeedTouchTM and click Next. The following window invites you to select the appropriate connection profile for your Internet connectivity: 3 Select the connection profile of your choice and click Next to continue. Note If the Service Provider has included a separate disk with a dedicated connection profile, click Have Disk to navigate to the location of the appropriate connection template file. 4 Subsequent screens will guide you through the configuration setup of both your SpeedTouchTM and/or your PC. Follow the instructions and enter the required information where needed. This information should be provided by your Service Provider. In a final step all configurations will be applied to the SpeedTouchTM and your PC. You can follow the configuration progress in following window: 5 12 E-SIT-CTC-20030605-0003 v1.0 1 SpeedTouchTM Installation 6 The SpeedTouchTM Setup wizard will appear again to announce that the configuration has been successful: Click Finish to close the wizard. Note In some cases, the SpeedTouchTM Setup wizard may ask you to restart your computer. Most configuration profiles will enable SpeedTouchTM's DHCP server - and a PC's Ethernet port is configured as DHCP client by default. Therefore, in most cases, no additional configuration of your PCs must be done if you want to enable multiple PCs on your local network for accessing the Internet via the SpeedTouchTM. To make sure that all PCs are configured as expected (DHCP or fixed IP addresses) you can re-run the SpeedTouchTM Setup wizard on every PC and select the Change the LAN configuration option. For fixed IP configurations, or other advanced settings, please follow the instructions provided by your ISP or network administrator. E-SIT-CTC-20030605-0003 v1.0 13 1 SpeedTouchTM Installation 1.3.2 Configuration Setup for other Operating Systems Supported Systems As the SpeedTouchTM is OS-independent, this configuration setup can be used by any computer system. Note TCP/IP The following procedure may equally be used on MS Windows OSs. Ensure that your operating system has a valid TCP/IP configuration. Configure your computer with a static Net10 private IP address, e.g. 10.0.0.1. Ensure, however, that you do NOT use the 10.0.0.138 IP address as this is the default IP address of the SpeedTouchTM. To ensure that IP connectivity exists, you can ping the SpeedTouchTM. Procedure The configuration setup proceeds as follows: 1 2 To ensure that the SpeedTouchTM is in its factory default state, reset the SpeedTouchTM to the default configuration. See "6 Troubleshooting" on page 65. Open a web browser and browse to the SpeedTouchTM's default IP address 10.0.0.138. See "3 SpeedTouchTM Web Interface" on page 31 for more information. As a result the SpeedTouchTM System Info web page appears. Expand the Advanced Topics and click Easy Setup. Note 4 If the SpeedTouchTM is in factory defaults, the Easy Setup wizard will appear automatically. 3 The Welcome to the SpeedTouchTM Setup Wizard window appears: Click Next to continue. 14 E-SIT-CTC-20030605-0003 v1.0 1 SpeedTouchTM Installation 5 The following window invites you to select the appropriate connection profile for your internet connectivity: In the Service list, click the connection profile of your choice. Note You can add services to the Services list by uploading templates. See " Templates" on page 48 for more information on uploading templates. 6 Subsequent screens guide you through the configuration setup of both your SpeedTouchTM and/or your PC. Follow the instructions and enter the required information where needed. This information should be provided by your Service Provider. In a final step all configurations are applied to the SpeedTouchTM: 7 8 The SpeedTouchTM Setup Wizard appears again to announce that the configuration has been successful: Click Finish to close the wizard. E-SIT-CTC-20030605-0003 v1.0 15 1 SpeedTouchTM Installation 9 After the configuration is applied on the SpeedTouchTM some additional configuration of your computer system may be necessary. Note The required settings for your computer should be provided by your Service Provider, if applicable. 10 To check whether the new configuration was successfully completed, you can browse to the SpeedTouchTM and check its current status. 16 E-SIT-CTC-20030605-0003 v1.0