User manual AMX ABS AXLINK BUS STRIP

instruction manual ABS AXlink Bus Strip C on t ro l S y s t em A c c e s s or ie s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are warranted for a period of one (1) year. Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. Software is warranted for a period of ninety (90) days. Batteries and incandescent lamps are not covered under the warranty. This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. Table of Contents Table of Contents Product Information .................................................................................................1 Specifications .................................................................................................................... 1 Installation and Wiring .............................................................................................3 Wiring Guidelines .............................................................................................................. 3 Preparing/connecting captive wires ......................................................................................... 3 Wiring ................................................................................................................................ 3 ABS AXlink Bus Strip i Table of Contents ii ABS AXlink Bus Strip Product Information Product Information The ABS AXlink Bus Strip (FIG. 1) is a 10-connector AXlink terminal strip designed to simplify connecting multiple AXlink devices in an AMX Control System. Use the included double-sided tape to securely affix the unit to the surface. FIG. 1 ABS Axlink Bus Strip Specifications The following table lists the specifications for the ABS Axlink Bus Strip. Specifications Power Connectors LED Enclosure Dimensions (HWD) Weight Mounting Options 12 VDC, 7 A max. Ten - 4-pin, captive-wire AXlink connectors One - 2-pin, captive-wire power connector Power indicator (Red) Metal with black matte finish 1.14" x 12.00" x 1.27" (2.90 cm x 30.48 cm x 3.23 cm) 6.70 oz (189.94 g) 4" double-sided foam tape ABS AXlink Bus Strip 1 Product Information 2 ABS AXlink Bus Strip Installation and Wiring Installation and Wiring Wiring Guidelines To determine the maximum distance allowed per gauge, use the following formula and refer to the table below: 1.5/(Power Consumption x Resistance x 2) = Distance (feet) Wiring Guidelines Gauge 18 AWG 20 AWG 22 AWG 24 AWG Resistance .00639 .0101 .0162 .0257 The maximum wiring lengths are based on a minimum of 13.5 volts available to the ABS. Preparing/connecting captive wires 1. Strip 0.25 inch of wire insulation off all wires. 2. Insert each wire into the appropriate opening on the connector according to the wiring diagrams and connector types described in this section. 3. Do not tighten the screws excessively; doing so may strip the threads and damage the connector. Wiring To wire the ABS: 1. Connect wiring from the AXlink devices to connectors 2 through 10 on the ABS (FIG. 2). If the power LED lights when an AXlink cable is connected to the ABS, it indicates the AXlink cable has a local power supply. Unless that local supply is intended to power all devices connected to the ABS, disconnect it and insulate the wire connected to the PWR+ terminal. All AXlink connectors on the ABS are connected together. 2. Connect the control system AXlink connector 1 on the ABS. As with the other AXlink devices in the system, connect all four wires to the ABS unless the Central Controller is using a local power supply. 3. Connect the system power supply to the 2-pin connector on the ABS. The power LED should light, and all AXlink devices with PWR+ connected to the ABS should have power. ABS AXlink Bus Strip 3 Installation and Wiring AXlink Conn. 10 PWR + (RED) AXP (WHT) AXM (GRN) GND - (BLK) AXlink Conn. 9 AXlink Conn. 8 AXlink Conn. 7 AXlink Conn. 6 AXlink Conn. 5 AXlink Conn. 4 AXlink Conn. 3 AXlink Conn. 2 AXlink Conn. 1 Power Conn. PWR GND AXlink Device 9 AXlink Device 8 AXlink Device 7 AXlink Device 6 AXlink Device 5 AXlink Device 4 AXlink AXlink Device 3 Device 2 AXlink Device 1 Control System System Power Supply FIG. 2 ABS wiring diagram If the AXlink devices have local power supplies, do not connect to the power terminal of the ABS via the PWR+ (Red). For additional information about the wiring distances between the ABS and a specific AXlink device, refer to the appropriate manual. 4 ABS AXlink Bus Strip Installation and Wiring ABS AXlink Bus Strip 5 AMX reserves the right to alter specifications without notice at any time. brussels · dallas · los angeles · mexico city · philadelphia · shanghai · singapore · tampa · toronto · york 3000 research drive, richardson, TX 75082 USA · 469.624.8000 · 800.222.0193 · fax 469.624.7153 · technical support 800.932.6993 041-004-1561 8/01 ©2001 AMX Corporation. All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation. AMX reserves the right to alter specifications without notice at any time. *In Canada doing business as Panja Inc.