User manual AMX NXA-WAP200G 802.11G WIRELESS ACCESS POINT

instruction manual NXA-WAP200G Modero Wireless Access Point and External Antennas Tou c h Pa n els an d A cc e ss o r ie s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers. Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. AMX Software is warranted for a period of ninety (90) days. Batteries and incandescent lamps are not covered under the warranty. · · · This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer. All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a valid RMA number. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed an operated with a minimum distance of 20 centimeters between the radiator and your body. Table of Contents Table of Contents Introduction ...............................................................................................................1 Specifications .................................................................................................................... 2 WAP200G Connector Locations ....................................................................................... 4 LEDs ........................................................................................................................................ 4 WAP200G Accessories ............................................................................................5 NXA-WAP2403A 3 dBi Ceiling Mount Omnidirectional Antenna....................................... 5 NXA-WAP2405A 5.5 dBi Rack/Ceiling Mount Antenna .................................................... 7 NXA-WAP2410A 10 dBi Directional Yagi Antenna ......................................................... 10 NXA-WAP2413A 13 dBi Indoor/Outdoor Directional Panel Antenna .............................. 13 Installation ...............................................................................................................17 WAP Location and Antenna Direction ............................................................................. 17 Mounting the WAP200G using the mounting holes ............................................................... 17 Connecting the Optional Accessory Antennas ................................................................ 18 Connecting the WAP to a LAN ........................................................................................ 18 Set the AP/BRIDGE Slide Switch.................................................................................... 18 Determining the Power Source (AC or PoE) ................................................................... 19 Configuring the Communication ...........................................................................21 Programming the Network Configuration ........................................................................ 21 Connecting to the WAP200G (cable connection)................................................................... 22 Connecting to the WAP200G (wirelessly) .............................................................................. 23 Wireless Device Communication Setup ...............................................................27 Logging into the WAP200G within Access Point Mode................................................... 27 WAP200G and Modero Unsecured Communication Setup ............................................ 28 Preparing the WAP for unsecured communication ................................................................ 28 Configuring the Modero panel for unsecured access............................................................. 30 Configuring the WAP200G for Secured Communication ................................................ 32 Configuring the Modero panel for secured access................................................................. 32 Preparing the WAP for secured communication .................................................................... 35 Configuring a secured connection on multiple wireless Moderos .......................................... 38 Configuring the WAP200G with a Static IP Address.............................................................. 39 Logging into the WAP200G within Bridge Mode ............................................................. 41 Configuring the WAP200G for Secured Bridge Mode Communication ........................... 42 Configuring the Modero panel for secured access (bridge mode) ......................................... 46 Upgrading the WAP200G On-Board Firmware ............................................................... 46 NXA-WAP200G Wireless Access Point i Table of Contents AP/Repeater Configuration Utility Pages ............................................................. 49 Status Page..................................................................................................................... 49 Connected Devices Page................................................................................................ 50 Basic Wireless Configuration Page................................................................................. 51 Access Control Page....................................................................................................... 53 Repeater Configuration Page.......................................................................................... 55 Advanced Wireless Configuration Page.......................................................................... 57 Security and Encryption Settings Page........................................................................... 58 Configuration of a WEP security protocol .............................................................................. 59 WPA Configuration................................................................................................................. 59 802.1X Configuration ............................................................................................................. 59 IP Address Configuration Page....................................................................................... 60 Administration Page ........................................................................................................ 61 Help Page ....................................................................................................................... 62 Bridge Mode Configuration Utility Pages ............................................................ 63 Status Page (Bridge Mode)............................................................................................. 63 Basic Wireless Configuration Page (Bridge Mode) ......................................................... 65 Security and Encryption Settings Page (Bridge Mode) ................................................... 67 Advanced Wireless Configuration (Bridge Mode) ........................................................... 68 Administration Page (Bridge Mode) ................................................................................ 69 Help Page (Bridge Mode)................................................................................................ 71 Troubleshooting .............................................................................................................. 71 Appendix ................................................................................................................. 73 Glossary of Terms........................................................................................................... 73 ii NXA-WAP200G Wireless Access Point Introduction Introduction AMX's new NXA-WAP200G 802.11g Wireless Access Point/Wireless Bridge (FG2255-01) provides both high performance and increased security to support all of AMX's G4 Modero wireless touch panels. The NXA-WAP200G provides convenient WLAN access for office/home computers with connection speeds of up to 54Mbps. The NXA-WAP200G integrates Power Over Ethernet (PoE), Repeater, and Bridge capabilities which increase your deployment and coverage options while easing the installation process. PoE allows you to deploy access points within locations where it would normally be difficult and time consuming to run electrical wiring. PoE is an IEEE 802.3af standard for distributing power over either a CAT5 (capable of up to 10/100 Mbps transmission) or CAT6 (capable of up to 1 Gbps transmission) Ethernet cable. Within this configuration, power is integrated onto the Ethernet cable through the PoE injector switch. Power and data are then sent across the Ethernet cable to the terminal device which then separates the power and data. The NXA-WAP200G can be deployed in one of three modes to increase its deployment to those locations where it could prove difficult to wire CAT5 Ethernet cables: Access Point Mode - In this mode the WAP200G is connected to the LAN through a CAT5 Ethernet cable and enables all of AMX's G4 Modero Wireless Touch Panels to connect to the network wirelessly. AP/Repeater Mode - When trying to install the WAP200G in a location that has electricity but does not have an Ethernet connection, such as a brick wall with an existing electrical outlet; the WAP can be placed in the AP/Repeater mode. This configuration allows it to provide coverage for that area and send network traffic through another AP back to the wired network using the Wireless Distribution System (WDS). Bridge Mode - In this mode, the WAP200G allows devices with only wired 10/100 Ethernet ports (such as a Printer, PlayStation2, X-Box, PVR, etc.) to be connected to the LAN wirelessly. This 802.11g WAP is also fully compatible with IEEE 802.11b standards, so it can connect with any existing 802.11b compliant devices. In addition, the WAP200G functions in tandem with optional external antennas that meet a variety of reception/transmission needs. Each antenna provides coverage which suits their particular installation needs and site requirements. Refer to the WAP200G Accessories section on page 5 for more information. NXA-WAP200G Wireless Access Point 1 Introduction Specifications The following table outlines the specifications for the NXA-80211G AMX Wireless Access Point. Specifications Dimensions (HWD): Weight: Power: · Antenna fully lowered: 1.34" x 5.12" x 4.33" (34 mm x 130 mm x 110mm) · Antenna fully raised: 3.94" x 5.12" x 4.33" (100 mm x 130 mm x 110mm) · Stand-alone unit: 0.50 lbs (0.23 kg) · Unit with power adapter: 0.85 lbs (0.39 kg) Linking State Current Draw: · 650 mA @ 5 VDC Full Load Current Draw (during transmission): · 820 mA @ 5 VDC while transmitting at 54 Mbps · 750 mA @ 5 VDC while transmitting at 11 Mbps Full Load Current Draw (during reception): · 750 mA @ 5 VDC while receiving at 54 Mbps · 700 mA @ 5 VDC while receiving at 11 Mbps Radio Specifications: WLAN standards Media Access protocol Frequency Operating channels · IEEE802.11/11b Industry standards · IEEE 802.11g draft standards · IEEE802.11 · 2.412 - 2.484 GHz (Industrial Scientific Medical Band) · 11b Mode: - 11 Channels (USA, Canada) - 13 Channels (Europe) - 14 Channels (Japan) - 4 Channels (France) · 11g Mode: - 11 Channels (USA, Canada) - 13 Channels (Europe, Japan) - 4 Channels (France) Wireless Restrictions · In R&TTE countries, such as France, the 802.11g frequency band is restricted to 2454 - 2483.5 MHz (2.454 - 2.4835 GHz) and a max power output of 100 mW EIRP outdoors. · 1, 2, 5.5, 6, 9, 11, 12, 24, 36, 48, and 54 Mbps · CCK for 11b mode (1, 2, 5.5, and 11 Mbps) · OFDM for 11g mode (6, 9, 12, 24, 36, 48, and 54 Mbps) Security Output power Coverage area Firmware/Software Specifications: Management Firmware upgrade IP configuration Protocols · Built-in browser-based management with User Name/Password authentication · TFTP · Static IP or DHCP client · Transparent to layer 3 protocols, such as PPoE and VPN · 64-bit & 128-bit WEP Encryption · 15 dBm @ 11M CCK · 10 dBm @ 54M OFDM · Indoor: 100 ft (30.48 m) · Outdoor: 100 ft (30.48 m) Data Rate Modulation technique 2 NXA-WAP200G Wireless Access Point Introduction Specifications (Cont.) Front Components: LEDs Rear Components: Power connector Two power options available: · AC Adapter connects to an external power adapter. · Power Over Ethernet (PoE) powers the device through the CAT5 cable. Both Power and Data can be transmitted simultaneous through the CAT5 cable when using the appropriate equipment. Reset button · Pressing this button for 10 seconds, restores the default settings. Note: Resetting the WAP will erase all of your settings (WEP Encryption, Wireless and LAN settings, Passwords, etc.) and restore them to their factory default values. Do not reset the WAP if you want to retain these settings. LAN port · One 10/100M (RJ-45) connector. · This 10/100 Ethernet Port (RJ-45 Connector) is used to connect the WAP to your LAN and/or to connect your Internet device to the LAN when the NXA-WAP200G is used as a Bridge. LAN/PC switch The NXA-WAP200G can operate as a Wireless Access Point or as a Bridge. · Single AP - BRIDGE toggle switch · When configured as a Wireless Access Point it allows multiple computers to connect to the LAN wirelessly. · When configured as a Bridge it allows devices with a 10/100 port, but without wireless capability, to be connected to the wireless LAN, such devices include desktop computers, printers, X-Boxes, PlayStation2s, PVRs, Stereos, etc. · When the NXA-WAP200G is used a Wireless Access Point the toggle switch should be positioned to AP. · When it is used as a Bridge it should be positioned to BRIDGE. Antenna connector · Single 3 dBi external antenna with reversed SMA connector. · This is the connection point for any of the four optional external antennas. Refer to the WAP200G Accessories section on page 5 for more information. Certifications: Security Features: · FCC, IC, CE, TELEC · MAC Address filtering · Disabling of Wireless Beacon · Hiding of SSID information · 64 and 128-bit WEP Encryption Operating/Storage Environments: · Operating Temperature: 0°C (32°F) to 50°C (122°F) · Storage Temperature: -25°C (-13°F) to 70°C (158°F) · Relative Humidity: 10% to 90% non-condensing Included Accessories: · One power adapter · Four international plug adapters (US/Japan, Europe, UK, and Australia) · Surface mounting kit (including two screws) · Three blue activity and status LED indicators · Refer to the following LEDs section on page 4 for more information. NXA-WAP200G Wireless Access Point 3 Introduction Specifications (Cont.) Optional Accessories: · NXA-WAP2403A, 3 dBi Ceiling Mount Omnidirectional Antenna (FG2255-20) · NXA-WAP2405A, 5.5 dBi Rack/Ceiling Mount Antenna (FG2255-21) · NXA-WAP2410A, 10 dBi Directional Yagi Antenna (FG2255-23) · NXA-WAP2413A, 13 dBi Indoor/Outdoor Directional Panel Antenna (FG2255-22) WAP200G Connector Locations FIG. 1 shows the back panel of the NXA-WAP200G wireless access point: Power port Ethernet connector Antenna connector RESET button FIG. 1 NXA-WAP200G (rear view) AP/BRIDGE switch LEDs The LEDs are indicators of switch activity and performance. The following table shows the status of the LEDs. You can check each connection by viewing the port status indicators shown in the following table. Device LED Descriptions LED PWR (power) Status Blue: On Blue: Off WLAN - Link/Activity Blue: On Blue: Blinking LAN - Link/Activity Blue: On Blue: Blinking Description Power is supplied to the device Power is disconnected from the device Wireless LAN is active Wireless data is being transmitted Connected to LAN/Internet Device Indicates data activity 4 NXA-WAP200G Wireless Access Point WAP200G Accessories WAP200G Accessories The following section outlines and describes the optional WAP200G accessory antennas: NXA-WAP2403A, 3 dBi Ceiling Mount Omnidirectional Antenna (FG2255-20) NXA-WAP2405A, 5.5 dBi Rack/Ceiling Mount Antenna (FG2255-21) NXA-WAP2410A, 10 dBi Directional Yagi Antenna (FG2255-23) NXA-WAP2413A, 13 dBi Indoor/Outdoor Directional Panel Antenna (FG2255-22) Each antenna is designed to meet the needs required by a particular installation location. NXA-WAP2403A 3 dBi Ceiling Mount Omnidirectional Antenna This 2.4 GHz Omni-directional antenna (FIG. 2) is designed for applications that require a frequency coverage from 2.4 GHz to 2.5 GHz. FIG. 2 NXA-WAP2403A Omnidirectional Ceiling Mount Antenna Specifications for NXA-WAP2403A Dimensions (HWD): Description: Features: · 5.00" x 10.0" x 0.12" (127.0 mm x 254.0 mm x 3.05 mm) · 3 dBi Ceiling Mount Omni-directional Antenna (@ 2.4 GHz). · 3 dBi antenna provides true omni-directional performance. · 3 foot (0.915 m) UL910 Plenum cable can be installed in the strictest indoor mounting locations (including air ducts). · Dual 10-32 stud mount.\ · Utilizes UL94-V0 materials which provide the UL's highest flame retardant rating. This use of materials provides maximum placement flexibility while meeting the most stringent building codes. Weight: Max Power Input: Frequency Range: Nominal Gain: Isolation: · 0.5 lbs (0.23 kg) · 20 Watts · 2400-2500 MHz · 3 dBi · > 25 dB NXA-WAP200G Wireless Access Point 5 WAP200G Accessories Specifications for NXA-WAP2403A (Cont.) Horizontal Bandwidth: Vertical Bandwidth: VSWR: Mounting Method: Nominal Impedance: Polarization: Cable: Connector Type: Operating Temperature: Certifications: Included Accessories: Optional Accessories: · 360° · 55° · < 2.0 : 1 · Dual 10-32 stud mount. · 50 Ohms · Vertical, linear · 3 foot (0.915 m) Plenum RG58/U · Reverse polarity SMA · -40°C to +70°C · FCC (United States) · CE (Europe) · 3 dBi Omni-directional antenna. · 3 foot (0.915 m) UL910 Plenum cable. · NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26) FIG. 3 represents the NXA-WAP2403A Elevation cut. FIG. 3 NXA-WAP2403A Elevation cut 6 NXA-WAP200G Wireless Access Point WAP200G Accessories FIG. 4 represents the NXA-WAP2403A Azimuth cut. FIG. 4 NXA-WAP2403A Azimuth cut NXA-WAP2405A 5.5 dBi Rack/Ceiling Mount Antenna This antenna is designed to cover frequencies from 2400 to 2485 MHz with a VSWR of less than 1.5:1. The NXA-WAP2405A antenna (FIG. 5) design focuses energy where it is needed while reducing extraneous transmissions. FIG. 5 NXA-WAP2405A Omnidirectional Rack/Ceiling Mount Antenna NXA-WAP200G Wireless Access Point 7 WAP200G Accessories Specifications for NXA-WAP2405A Dimensions (L & OD): Description: Features: · 9.8" L x 1.0" OD (248.9 mm x 25.4 mm) · 5.5 dBi Rack/Ceiling Mount Omnidirectional Antenna (@ 2.4 GHz). · 5.5 dBi Omnidirectional Antenna. · An included 1/4-20 insert allows for easy installation onto ceiling tile rails. · Optimized radiation pattern focuses energy where it is needed, while at the same time, suppressing both upper and lower sidelobe energy. · UL Plenum rated RG58 coax cable and UL94-V0 radome meet the strictest safety specifications. Weight: Wind Survival: Max Power: Frequency Range: Nominal Gain: Horizontal Bandwidth: Vertical Bandwidth: VSWR: Mounting Method: Nominal Impedance: Polarization: Cable: Connector Type: Operating Temperature: Certifications: Included Accessories: Optional Accessories: · 0.5 lbs (0.23 kg) · 125 mph (201.17 kph) · 5 Watts · 2400-2485 MHz · 5.5 dBi · 360° · 32° · < 1.5 : 1 · 1/4-20 insert for clipping to a ceiling tile rail. · 50 Ohm · Vertical, linear · 12" (30.5 cm) RG58 · Reverse polarity SMA · -30°C to 75°C · FCC (United States) · CE (Europe) · A 1/4-20 insert allows for easy installation onto ceiling tile rails. · NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26) 8 NXA-WAP200G Wireless Access Point WAP200G Accessories FIG. 6 represents the NXA-WAP2405A Elevation cut. FIG. 6 NXA-WAP2405A Elevation cut FIG. 7 represents the NXA-WAP2403A Azimuth cut. FIG. 7 NXA-WAP2405A Azimuth cut NXA-WAP200G Wireless Access Point 9 WAP200G Accessories NXA-WAP2410A 10 dBi Directional Yagi Antenna This antenna can be used as bridge between two networks and/or point-to-point communications. This design also provides improved front-to-back ratio and sidelobe suppression (reducing interference). It features a robust mounting structure for consistent performance, regardless of weather conditions. The NXA-WAP2410A antenna (FIG. 8) is field adjustable for vertical or horizontal polarization with matched principal plane beamwidths (providing optimum performance in either orientation). Front view Rear view FIG. 8 NXA-WAP2410A Outdoor Enclosed Yagi Antenna Specifications for NXA-WAP2410A Dimensions (L & OD): Description: Features: · 4.5" L x 3.0" OD (114 mm x 76 mm) · 10 dBi Directional Yagi Antenna (@ 2.4 GHz). · 10 dBi directional antenna. · A 30 dB front-to-back ratio permits less physical separation on the tower, thus adding mounting flexibility at installation sites where space is limited. · Attractive weather-proof radome is constructed of UV resistant material. This construction provides robust and trouble-free use in harsh outdoor environments. · Field adjustability allows for both vertical or horizontal polarity. This feature eliminates co-channel interference from neighboring radiators. · Includes a robust mast mount bracket which is designed to withstand up to 125 mph winds. · Matched principal plane beamwidths provide excellent sidelobe suppression and cross-polarization rejection of more than 20 dB. · Provides superior signal quality (with enhanced gain performance) and minimal interference from neighboring radiators. · Polarity markings are molded onto the antenna and ensure installation in the correct orientation. · Small and unobtrusive 4.5" x 3" design enables a user to bridge any two buildings without compromising the architecture. Weight: Equivalent Flat Plate Area: Wind Survival: Lateral Thrust at Rated Wind: Max Power: · 1.0 lbs (0.5 kg) · 0.060 ft2 · 125 mph (201.17 kph) · 5.8 lbs (2.63 kg) · 5 Watts 10 NXA-WAP200G Wireless Access Point WAP200G Accessories Specifications for NXA-WAP2410A (Cont.) Frequency Range: Front to Back Ratio Nominal Gain: Horizontal Beamwidth: Vertical Beamwidth: VSWR: Mounting Method: · 2400-2485 MHz · 23 dB · 10 dBi · 55° (@ 1/2 power) · 55° (@ 1/2 power) · < 1.5 : 1 · Heavy duty Yagi mounting bracket. · MYK18 adjustable wall/pipe mount. · Stacking harnesses. Nominal Impedance: Polarization: Cable: Connector Type: Operating Temperature: Certifications: Included Accessories: Optional Accessories: · 50 Ohms · Vertical or horizontal, linear (user adjustable) · 3 foot (914.4 mm) · Reverse polarity SMA · -30°C to 75°C · FCC (United States) · CE (Europe) · Heavy duty Yagi mounting bracket permits mast mounting on masts up to 2" O.D. · NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26) NXA-WAP200G Wireless Access Point 11 WAP200G Accessories FIG. 9 represents the NXA-WAP2410A Elevation cut. FIG. 9 NXA-WAP2410A Elevation cut FIG. 10 represents the NXA-WAP2410A Azimuth cut. FIG. 10 NXA-WAP2410A Azimuth cut 12 NXA-WAP200G Wireless Access Point WAP200G Accessories NXA-WAP2413A 13 dBi Indoor/Outdoor Directional Panel Antenna This antenna is designed to cover 2.4 GHz frequencies with a VSWR of less than 1.5:1. This allows it to obtain a maximum gain, while still maintaining an attractive, low-profile package. The NXAWAP2413A antenna (FIG. 8) provides both efficient and stable performance, while providing both indoor or outdoor mounting options. Top view Bottom view FIG. 11 NXA-WAP2413A Indoor/Outdoor Directional Panel Antenna Specifications for NXA-WAP2413A Dimensions (HWD): Description: Features: · 8.8" x 8.1" x 1.6" (224.0 mm x 206.0 mm x 40.60 mm) · 13 dBi Indoor/Outdoor Directional Antenna (@ 2.4 GHz). · 13 dBi directional antenna. · Attractive, low profile housing. Permits the unit to be mounted in either vertical or horizontal polarity. · Blends well with indoor and outdoor environments where aesthetic considerations are important. · Corner exit RG58 pigtail design permits the panel to be mounted in vertical or horizontal polarity with a wide variety of connector options. · Utilizes UL94-V0 materials and PC board that provide the UL's highest flame retardant rating for maximum placement flexibility. Meets most stringent building codes. Weight: Radome Material: Max Power Input: Frequency Range: Front to Back Ratio Nominal Gain: Horizontal Beamwidth: Vertical Beamwidth: VSWR: Mounting Method: Nominal Impedance: Lightning Protection: Polarization: · 1.2 lbs (0.54 kg) · UL94-V0 plastic · 20 Watts · 2300-2500 MHz · > 18 dB · 13 dBi · 35° @ 3 dB · 35° @ 3 dB · < 1.5 : 1 · Adjustable azimuth/elevation MPAB11 mount. · 50 Ohms · DC grounded · Vertical or horizontal, linear NXA-WAP200G Wireless Access Point 13 WAP200G Accessories Specifications for NXA-WAP2413A (Cont.) Cable: Connector Type: Operating Temperature: Certifications: Included Accessories: Optional Accessories: · 12" (30.5 cm) RG58/U · Reverse polarity SMA · -40°C to +80°C · FCC (United States) · CE (Europe) · Adjustable mounting brackets for indoor installation. · Indoor corner mounting bracket and heavy duty outdoor mounting brackets are also available.These provide maximum flexibility for both indoor or outdoor installations. · NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26) · NXA-WAP2413AMB - Mounting Bracket for the NXA-WAP2413A (FG2255-24) · NXA-WAP2413ACMB - Corner Mounting Bracket for the NXA-WAP2413A (FG2255-25) FIG. 12 represents the NXA-WAP2413A Elevation cut. FIG. 12 NXA-WAP2413A Elevation cut 14 NXA-WAP200G Wireless Access Point