User manual AMX SLIM-BUTTON KEYPADS

Please Read Before Installing Installation Instructions Description The HWD-5KP, -5RL and HWD-10KP, -10RL keypads are for use with HomeWorks systems. The keypad buttons are programmed with a personal computer using the HomeWorks Utility. Up to 32 keypads, each with a unique address, can be connected to each keypad link on the HomeWorks Wired Processor. A maximum of 300 keypad LEDs can be connected per processor. To increase the number of LEDs, see the HomeWorks Technical Reference Guide. Designer-Style Wired Slim-Button Keypads HWD-5KP, -5RL, -10KP, -10RL 15 V , 42 mA HWD-5KP HWD-5RL Important Notes Codes: Install in accordance with all local and national electrical codes. Environment: Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing. Indoor use only. Wallplates: Lutron Claro® and Satin ColorsTM wallplates are recommended for best color match and clean aesthetic appearance. Do not paint controls or wallplates. Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning solutions. Wallboxes: Lutron recommends using 3 1/2" (89mm) deep wallboxes for easier installation. HWD-10KP HWD-10RL 1 Installation 1. Disconnect power to the keypads by turning off all circuit breakers connected to the HomeWorks® Processor or keypad link auxiliary power supply. Danger - Wiring with power ON may result in personal injury. 4. 5. 6. 7. 8. Unplug terminal block from the keypad circuit board. Connect wiring to terminal block as shown in Figures 1 and 2 (page 3). Plug the keypad terminal block back onto the circuit board. Be sure to orient the terminal block correctly. Mount keypad as shown in Figure 4 (page 4). Do not over-tighten mounting screws. Restore power to the HomeWorks Processor or keypad link auxiliary power supply. 2. Address keypads. Assign a unique address to each keypad using the DIP switch on the back of the keypad. See Figure 2 (page 3) for DIP switch location. See Figure 3 (page 4) for DIP switch settings. Be sure to record the address for future programming purposes. Strip insulation from wires to 3/8" (10mm). Each terminal will accept one or two 18-gauge (1.0mm2) wires. 3. Mounting Diagram Keypad Mounting Screws Adapter Mounting Screws Wallbox Keypad Included: Wallplate and Adapter are purchased separately. Mounting Screws (2) 2 Low-Voltage (Class 2/PELV) Wiring Diagram Keypads can be connected to any of these three links depending on the configuration of the HomeWorks® Utility Pins 1 & 2 - 1 pair #18 AWG (1.0mm2) for power Pins 3 & 4 - 1 pair #18-22 AWG (1.0 - 0.5mm2) twisted shielded for data Keypad Addressing Keypad Rear View DIP Switches Set DIP switches 1-5 to give the keypad a unique HomeWorks system address from 1 to 32. Switch Settings Switch Settings Switch Settings ON Address # 1 123456 ON Address # 9 2 3 4 5 6 2 3 4 5 6 ON Address # Address # 6 Switch Settings ON 17 2 3 4 5 6 2 3 4 5 6 1 ON 1 1 2 3 4 5 25 26 27 28 29 30 31 32 1 ON 2 3 4 5 6 DIP switches 1-5 for setting address, DIP switch 6 does not affect keypad address. MUX PELV (Class 2: MUX USA) wiring con+15VDC nections to COM 2 3 4 1 ON 10 11 12 13 14 15 16 ON 1 ON 18 19 20 21 22 23 24 ON 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1234 5 6 7 8 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 HomeWorks Wired Processor or other Keypads. 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 ON 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 Example: Setting Switch #1 ON. UP (ON) DOWN (OFF) ON 1 2 3 4 5 6 3 Troubleshooting Guide Symptom LEDs don't light up even when buttons are pushed. Cause and Action Power is not present at keypad. · Make sure HomeWorks Processor is powered. · Check for 15 VDC between pins 1 & 2 on the keypad connector. · Remove connector from back of keypad, check connections and replace. LEDs cycle from top to bottom sequentially. Keypad is working properly but is not communicating with the processor. · Verify that the processor is powered. · Check that keypad wires 3 & 4 are properly connected. · Check that keypad link is plugged into correct connector at processor. · Verify that link is configured for HomeWorks keypads in the HomeWorks Utility. LEDs light when button is pressed, but the system response isn't correct. · Check keypad for proper address using table on previous page. · Check system programming. LIMITED WARRANTY Technical and Sales Assistance If you need assistance, call the toll-free Lutron Technical Support Center. Please provide exact model number when calling. (800) 523-9466 (U.S.A., Canada and the Caribbean) Other countries call: Tel: (610) 282-3800 Fax: (610) 282-3090 Visit our Web site at www.lutron.com Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 Made and printed in the U.S.A. 3/03 P/N 043-121 Rev. A 93-2605-03 Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within two years after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. After the two year period, a pro-rated warranty applies to this product until eight years after the purchase. For more information regarding this warranty contact your Lutron representative. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON'S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.This product may be covered by one or more of the following U.S. patents: 4,835,343; 4,889,999; 5,170,068; 5,237,207; D344,068; D378,814 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, Claro, and HomeWorks are registered trademarks and Satin Colors is a trademark of Lutron Electronics Co., Inc. © 2003 Lutron Electronics Co., Inc.