775i48 User Manual Version 1.0 Published October 2004 Copyright©2004 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ASRock Website: http://www.asrock.com 2 Contents 1 Introduction ................................................... ... 5 1.1 1.2 1.3 1.4 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 Package Contents................................................................ 5 Specifications ..................................................................... 6 Motherboard Layout ........................................................... 8 ASRock I/O PlusTM ............................................................... 9 Screw Holes ...................................................................... 10 Pre-installation Precautions ................................................ 10 CPU Installation ................................................................... 11 Installation of CPU Fan and Heatsink .................................. 13 Installation of Memory Modules (DIMM) .............................. 14 Expansion Slots (PCI and AGP Slots) ................................. 15 Jumpers Setup ................................................................... 16 Onboard Headers and Connectors .................................... 17 Serial ATA (SATA) Hard Disks Installation ........................... 20 21 21 22 22 23 23 24 26 27 29 30 30 32 32 33 33 34 34 35 2 Installation ............................................. 10 3 BIOS SETUP UTILITY...................................... 21 3.1 Introduction .......................................................................... 3.1.1 BIOS Menu Bar ......................................................... 3.1.2 Navigation Keys ....................................................... 3.2 Main Screen ........................................................................ 3.3 Advanced Screen ............................................................... 3.3.1 CPU Configuration .................................................... 3.3.2 Chipset Configuration ............................................... 3.3.3 ACPI Configuration ................................................... 3.3.4 IDE Configuration ...................................................... 3.3.5 PCIPnP Configuration ................................................ 3.3.6 Floppy Configuration ................................................ 3.3.7 Super IO Configuration ............................................. 3.3.8 USB Configuration .................................................... 3.4 Hardware Health Event Monitoring Screen ........................ 3.5 Boot Screen ........................................................................ 3.5.1 Boot Settings Configuration ..................................... 3.5.2 Boot Device Priority .................................................. 3.6 Security Screen .................................................................. 3.7 Exit Screen .......................................................................... 3 4 Software Support ........................................... 36 4.1 Install Operating System ............................................... 4.2 Support CD Information ................................................. 4.2.1 Running Support CD ............................................ 4.2.2 Drivers Menu ........................................................ 4.2.3 Utilities Menu ........................................................ 4.2.4 ASRock "PC-DIY Live Demo" Program ................. 36 36 36 36 36 36 4.2.5 "LGA 775 CPU Installation Live Demo" Program.... 36 4.2.6 Contact Information .............................................. 36 4 Chapter 1 Introduction Thank you for purchasing ASRock 775i48 motherboard, a reliable motherboard produced under ASRock's consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock's commitment to quality and endurance. In this manual, chapter 1 and 2 contain introduction of the motherboard and step-bystep guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD. Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest memory and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com 1.1 Package Contents ASRock 775i48 Motherboard (ATX Form Factor: 12.0-in x 7.2-in, 30.5 cm x 18.3 cm) ASRock 775i48 Quick Installation Guide ASRock 775i48 Support CD (including LGA 775 CPU Installation Live Demo) One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive One Serial ATA (SATA) Data Cable One Serial ATA (SATA) HDD Power Cable (Optional) One ASRock I/O PlusTM Shield 5 1.2 Specifications Platform: CPU: ATX Form Factor: 12.0-in x 7.2-in, 30.5 cm x 18.3 cm 775-Pin Socket supporting Intel® Pentium® 4 / Celeron® processor (in 775-land LGA package) North Bridge: Intel® 848P chipset, FSB @ 800 / 533 MHz, Max. 1066 MHz at overclocking mode (see CAUTION 1), supports Hyper-Threading Technology (see CAUTION 2) South Bridge: Intel® ICH5, supports SATA 1.5Gb/s Memory: 2 DDR DIMM slots: DDR1 and DDR2 supports PC3200 (DDR400) / PC2700 (DDR333) / PC2100 (DDR266), Max. 2GB (see CAUTION 3) IDE: IDE1: ATA 100 / Ultra DMA Mode 5 IDE2: ATA 100 / Ultra DMA Mode 5 Supports up to 4 IDE devices Serial ATA: Supports up to 2 SATA devices at 1.5Gb/s data transfer rate (Not Support "RAID" and "Hot Plug" functions) Floppy Port: Supports up to 2 floppy disk drives Audio: 5.1 channels AC'97 Audio PCI LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN Hardware Monitor: CPU temperature sensing, Chassis temperature sensing, CPU overheat shutdown to protect CPU life (ASRock U-COP)(see CAUTION 4), CPU fan tachometer, Chassis fan tachometer, Voltage monitoring: +12V, +5V, +3.3V, Vcore PCI slots: 5 PCI slots with PCI Specification 2.3 AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 5) USB 2.0: 8 USB 2.0 ports: includes 6 default USB 2.0 ports on the rear panel, plus one header to support 2 additional USB 2.0 ports (see CAUTION 6) ASRock I/O PlusTM: 1 PS/2 mouse port, 1 PS/2 keyboard port, 1 serial port: COM1, 1 parallel port: ECP/EPP support, 6 default USB 2.0 ports, 1 RJ 45 port, Audio Jack: Line In / Line Out / Microphone Chipsets: 6 BIOS: OS: AMI legal BIOS, Supports "Plug and Play", ACPI 1.1 compliance wake up events, Supports jumperfree, SMBIOS 2.3.1 support, CPU frequency stepless control (only for advanced users' reference, see CAUTION 7) Microsoft® Windows® 98 SE / ME / 2000 / XP compliant CAUTION! 1. To support FSB1066, please use DDR400 DIMMs (Double Data Rate 400 MHz). Before installing FSB1066 CPU, please make sure that you have adjusted the jumpers correctly. The default setting of FSB1 is shorting pin1 and pin2. However, if you want to support FSB1066 CPU, please 2. 3. adjust your FSB1 jumper setting, and short pin2 and pin3 (see page 16). About the setting of "Hyper Threading Technology", please check page 24. Please check the table below for the memory support frequency and its corresponding CPU FSB frequency. CPU FSB Frequency 800 533 Memory Support Frequency DDR266, DDR320*, DDR400 DDR266, DDR333 * When you use an FSB800-CPU on this motherboard, it will run at 4. DDR320 if you adopt a DDR333 memory module. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system. 5. 6. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage! Power Management for USB 2.0 works fine under Microsoft® Windows® XP SP1 / 2000 SP4. It may not work properly under Microsoft® Windows® 98/ ME. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU. 7. 7 1.3 Motherboard Layout 12 18.3cm (7.2 in) 1 3 4 5 PS2_USB_PWR1 PS2 Mouse ATX12V1 PARALLEL PORT Ps2 Keyboard FSB800 COM1 DDR1 (64/72 bit, 184-pin module) DDR2 (64/72 bit, 184-pin module) USB 2.0 T: USB2 B: USB3 USB 2.0 T: USB0 Top: B: USB1 RJ-45 6 30.5cm (12.0in) 29 28 27 ATXPWR1 USB4_5 USB 2.0 1 T: USB4 B: USB5 CPU_FAN1 Intel 848P Chipset AGP 8X 1.5V_AGP1 DDR400 IDE2 Super I/O FSB1 26 25 2Mb BIOS IDE1 Top: Line In Center: Line Out Bottom: Mic In 1 7 8 PCI 1 775i48 PCI 2 LAN PHY Intel ICH5 9 10 5.1 CH CMOS Battery CLRCMOS0 PCI 4 Audio CODEC SATA CHA_FAN1 SATA2 SATA1 24 PCI 3 USB2.0 11 12 13 14 23 1 1 USB67 JR1 JL1 PCI 5 PLED PWRBTN 1 1 AUDIO1 AUX1 CD1 GAME1 FLOPPY1 IR1 SPEAKER1 1 HDLED RESET PANEL 1 22 21 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 19 16 17 18 19 20 21 22 23 24 25 26 27 28 29 18 17 16 15 External Speaker Connector (SPEAKER1) Infrared Module Connector (IR1) Floppy Connector (FLOPPY1) Game Connector (GAME1) Internal Audio Connector: CD1 (Black) Internal Audio Connector: AUX1 (White) Front Panel Audio Connector (AUDIO1) JR1 / JL1 Jumpers PCI Slots (PCI1- 5) Flash Memory FSB Select Jumper (FSB1) CPU Fan Connector (CPU_FAN1) Shared USB 2.0 Header (USB4_5, Blue) ATX Power Connector (ATXPWR1) PS2_USB_PWR1 Jumper ATX 12V Connector (ATX12V1) 775-Pin CPU Socket North Bridge Controller 184-pin DDR DIMM Slots (DDR DIMM1- 2) Secondary IDE Connector (IDE2, Black) Primary IDE Connector (IDE1, Blue) AGP Slot (1.5V_AGP1) South Bridge Controller Primary Serial ATA Connector (SATA1) Secondary Serial ATA Connector (SATA2) Clear CMOS Jumper (CLRCMOS0) Chassis Fan Connector (CHA_FAN1) USB 2.0 Header (USB67, Black) System Panel Connector (PANEL1) 8 1.4 ASRock I/O Plus TM 1 2 3 4 5 11 10 9 8 7 6 1 2 3 4 5 6 Parallel Port RJ-45 Port Line In (Light Blue) Line Out (Lime) Microphone (Pink) Shared USB 2.0 Ports (USB45) 7 8 9 10 11 USB 2.0 Ports (USB01) USB 2.0 Ports (USB23) Serial Port: COM1 PS/2 Keyboard Port (Purple) PS/2 Mouse Port (Green) 9 Chapter 2 Installation 775i48 is an ATX form factor (12.0" x 7.2", 30.5 x 18.3 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components. 2.1 Screw Holes Place screws into the holes indicated by circles to secure the motherboard to the chassis. Do not over-tighten the screws! Doing so may damage the motherboard. 2.2 Pre-installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. To avoid damaging the motherb ...