User manual ASUS M2NPV-VM

Motherboard M2NPV-VM E2527 First Edition V1 May 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ("ASUS"). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices ................................................................................................ vi Safety information ............................................................................. vii M2NPV-VM specifications summary .................................................. viii Chapter 1: Product introduction 1.1 1.2 1.3 Welcome! .............................................................................. 1-2 Package contents ................................................................. 1-2 Special features .................................................................... 1-2 1.3.1 1.3.2 1.4 1.5 Product highlights ................................................... 1-2 Innovative ASUS features ....................................... 1-5 Before you proceed .............................................................. 1-7 Motherboard overview .......................................................... 1-8 1.5.1 1.5.2 1.5.3 Motherboard layout ................................................ 1-8 Placement direction ................................................ 1-9 Screw holes ............................................................ 1-9 Installing the CPU ................................................. 1-10 Installing the heatsink and fan ............................. 1-12 Overview ............................................................... 1-12 Memory configurations ......................................... 1-12 Installing a DIMM ................................................... 1-16 Removing a DIMM ................................................. 1-16 Installing an expansion card .................................. 1-17 Configuring an expansion card .............................. 1-17 PCI slots ................................................................ 1-19 PCI Express x1 slot ............................................... 1-19 PCI Express x16 slot ............................................. 1-19 1.6 Central Processing Unit (CPU) ............................................ 1-10 1.6.1 1.6.2 1.7 System memory ................................................................. 1-12 1.7.1 1.7.2 1.7.3 1.7.4 1.8 Expansion slots ................................................................... 1-15 1.8.1 1.8.2 1.8.3 1.8.4 1.8.5 1.9 1.10 Jumpers .............................................................................. 1-20 Connectors ......................................................................... 1-23 1.10.1 Rear panel connectors .......................................... 1-23 1.10.2 Internal connectors ............................................... 1-25 iii Contents Chapter 2: BIOS setup 2.1 Managing and updating your BIOS ........................................ 2-2 2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 2.1.6 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.2.7 2.2.8 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.3.7 2.3.8 2.4 ASUS Update utility ................................................ 2-2 Creating a bootable floppy disk .............................. 2-5 ASUS EZ Flash 2 utility ........................................... 2-6 Updating the BIOS .................................................. 2-7 Saving the current BIOS file .................................... 2-9 ASUS CrashFree BIOS 2 utility .............................. 2-10 BIOS menu screen ................................................ 2-12 Menu bar ............................................................... 2-13 Legend bar ........................................................... 2-13 Menu items ........................................................... 2-13 Sub-menu items ................................................... 2-13 Configuration fields .............................................. 2-13 Pop-up window ..................................................... 2-14 General help .......................................................... 2-14 System Time ......................................................... 2-15 System Date ......................................................... 2-15 Legacy Diskette A ................................................ 2-15 Primary and Secondary IDE Master/Slave ............. 2-15 First, Second, Third, Fourth SATA Master ............ 2-18 HDD SMART Monitoring ........................................ 2-19 Installed Memory .................................................. 2-19 Usable Memory ..................................................... 2-19 BIOS setup program ........................................................... 2-11 Main menu .......................................................................... 2-15 Advanced menu .................................................................. 2-20 2.4.1 JumperFree Configuration ..................................... 2-20 2.4.2 2.4.3 2.4.4 2.4.5 2.4.6 AI NET2 ................................................................ 2-22 CPU Configuration ................................................. 2-22 Chipset ................................................................. 2-24 PCIPnP ................................................................... 2-25 Onboard Devices Configuration ............................ 2-26 iv Contents 2.5 Power menu ........................................................................ 2-30 2.5.1 2.5.2 2.5.3 2.5.4 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.6.5 2.6.6 2.7 2.7.1 2.7.2 2.8 ACPI Suspend Type ............................................... 2-30 ACPI APIC Support ................................................ 2-30 APM Configuration ................................................ 2-30 Hardware Monitor ................................................. 2-33 Boot Device Priority .............................................. 2-34 Removable Drives ................................................. 2-34 Hard Disk Drives ................................................... 2-35 CDROM Drives ....................................................... 2-35 Boot Settings Configuration ................................. 2-35 Security ................................................................ 2-38 ASUS O.C. Profile .................................................. 2-40 ASUS EZ Flash 2 ................................................... 2-42 Boot menu .......................................................................... 2-34 Tools menu ......................................................................... 2-40 Exit menu ........................................................................... 2-43 Chapter 3: Software support 3.1 3.2 Installing an operating system ............................................. 3-2 Support CD information ........................................................ 3-2 3.2.1 3.2.2 3.2.3 3.2.4 3.2.5 3.2.6 3.2.7 Running the support CD ......................................... 3-2 Drivers menu .......................................................... 3-3 Utilities menu .......................................................... 3-4 Make Disk menu ...................................................... 3-5 Manual menu ........................................................... 3-6 ASUS Contact information ...................................... 3-7 Other information ................................................... 3-7 v Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: · This device may not cause harmful interference, and · This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. vi Safety information Electrical safety · To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. · When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device. · Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged. · Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit. · Make sure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company. · If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer. Operation safety · Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package. · Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. · To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. · Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. · Place the product on a stable surface. · If you encounter technical problems with the product, contact a qualified service technician or your retailer. The symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Please check local regulations for disposal of electronic products. vii M2NPV-VM specifications summary CPU Support AMD socket AM2 for AMD AthlonTM 64FX/ AthlonTM 64 X2/AthlonTM 64/Sempron processors AMD64 architecture enables simultaneous 32-bit and 64-bit computing Supports AMD Cool `n' QuietTM Technology AMD Live!TM Ready Northbridge: NVIDIA® GeForceTM 6150 GPU Southbridge: NVIDIA® nForceTM430 MCP 2000/1600 MT/s Dual-channel memory architecture 4 x 240-pin DIMM sockets support up to 8 GB of unbufferred ECC/non-ECC 800/667/533 MHz DDR2 memory modules 1 x PCI ExpressTM x16 slot 1 x PCI ExpressTM x1 slot 2 x PCI slots Integrated in the NVIDIA® GeForceTM 6 Graphics Processing Unit (GPU) Dual VGA output: DVI-D and RGB High definition video processing with maximum resolution of 1920 x 1440 pixels (@75Hz) for RGB display N o t e : DVI-D only supports digital display. You cannot convert DVI-D to output RGB signal to CRT display. TV-out: SDTV& HDTV (with TV-Out module) N o t e : RGB and TV-Out cannot be used simultaneously. NVIDIA® nForceTM430 media and communications processor (MCP) supports: - 2 x Ultra DMA 133/100/66/33 interfaces for four (4) hard disk drives - 4 x Serial ATA 3 Gb/s hard disk drives supporting RAID 0, RAID 1, RAID 0+1, RAID 5, and JBOD configuration SoundMAX® ADI AD1986A 5.1-channel CODEC Supports Jack Sensing technology S/PDIF out interface NVIDIA® nForceTM430 built-in Gigabit MAC with external Marvell® PHY Supports up to 8 USB 2.0 ports (continued on the next page) Chipset Front Side Bus Memory Expansion slots Graphics Storage High Definition Audio LAN USB viii M2NPV-VM specifications summary IEEE 1394 Manageability Special features TI IEEE 1394a controller supports: - 2 x IEEE 1394a ports WfM2.0, DMI2.0, WOL by PME, WOR, PXE, Chassis Intrusion ASUS Q-Fan 2 ASUS C.P.R. (CPU Parameter Recall) ASUS CrashFree BIOS 2 ASUS EZ Flash 2 ASUS O.C. Profile ASUS MyLogoTM Stepless Frequency Selection (SFS) allows FSB tuning from 200 MHz to 400 MHz at 1 MHz increment N o t e : ASUS CrashFree BIOS 2 and ASUS EZ Flash 2 only support VGA/RGB output. 4 Mb Flash ROM, Award BIOS, PnP, DMI2.0, WfM2.0, ACPI 2.0, SM BIOS 2.3 1 x Parallel port 1 x IEEE 1394a port 1 x LAN (RJ-45) port 4 x USB 2.0 ports 1 x VGA/RGB Out port 1 x VGA/DVI-D port 1 x PS/2 keyboard port 1 x PS/2 mouse port 5.1-channel audio ports 1 x IEEE 1394a connector 1 x Front panel audio connector 1 x CD audio in connector 1 x Chassis intrusion connector 1 x Game/MIDI connector 1 x CPU fan connector 2 x Chassis fan connectors 1 x Floppy disk drive connector 2 x COM connectors 1 x Primary IDE connector 1 x Secondary IDE connector 1 x S/PDIF Out connector 1 x TV Out connector 4 x Serial ATA connectors 2 x USB 2.0 connectors for 4 additional USB 2.0 ports 1 x 24-pin ATX power connector 1 x 4-pin x ATX 12V power connector 1 x System panel connector (continued on the next page) BIOS features Rear panel Internal connectors ix M2NPV-VM specifications summary Power Requirement Form Factor Support CD contents ATX power supply (with 24-pin and 4-pin 12 V plugs) ATX 12 V 2.0 compliant uATX: 9.6 in. x 9.6 in. (24.5cm x 24.5cm) Device drivers ASUS PC Probe II AMD Cool `n'QuietTM utility ASUS Live Update utility Anti-virus software (OEM version) *Specifications are subject to change without notice. x This chapter describes the motherboard features and the new technologies it supports. Product introduction 1 1.1 Welcome! T h a n k y o u f o r b u y i n g a n A S U S® M 2 N P V - V M m o t h e r b o a r d ! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents ASUS M2NPV-VM motherboard 2 x Serial ATA signal cables 1 x Serial ATA power cable for two Serial ATA devices 1 x IEEE 1394a module 1 x Ultra DMA 133/100/66 cable 1 x IDE cable 1 x Floppy disk drive cable I/O shield 1 x HDTV/AV/S output module ASUS motherboard support CD User guide Check your motherboard package for the following items. Motherboard Cables Accessories Application CD Documentation If any of the above items is damaged or missing, contact your retailer. 1.3 1.3.1 Special features Product highlights Latest processor technology The motherboard supports AMD socket AM2 single-core Athlon 64/ Sempron and dual-core Athlon 64 X2/Athlon 64 FX processors with 2MB/ 1MB/512KB L2 cache, which is based on 64-bit architecture. It features 2000/1600 MT/s HyperTransport Bus, dual-channel un-buffered DDR2 800 memory support and AMD Cool `n' Quiet Technology. See page 1-10 for details. 1-2 Chapter 1: Product introduction AMD Cool `n' Quiet Technology The motherboard supports the AMD Cool `n' Quiet Technology, which monitors system operation and automatically adjusts CPU voltage and frequency for a cool and quiet operating environment. See page 2-23 for details. NVIDIA® GeForceTM 6150 GPU and NVIDIA® nForceTM 430 MCP chipsets The NVIDIA® GeForceTM 6150 graphics processing unit (GPU) Northbridge supports Microsoft® DirectX 9.0 Shader Model 3.0, dual VGA out (RGB and DVI-D), NVIDIA® PureVideo Technology with unprecedented integrated video quality, TV-out, and PCI Express interface. The NVIDIA® nForceTM 430 media and communications processor (MCP) Southbridge delivers NVIDIA® Gigabit and NVIDIA® MediaShield storage management technology allowing easy RAID configuration (RAID 0, RAID 1, RAID 0+1, RAID 5, and JBOD) for Serial ATA 3Gb/s. DDR2 memory support The motherboard supports DDR2 memory which features data transfer rates of 800MHz/667 MHz/533 MHz to meet the higher bandwidth requirements of the latest 3D graphics, multimedia, and Internet applications. The dual-channel DDR2 architecture doubles the bandwidth of your system memory to boost system performance, eliminating bottlenecks with peak bandwidths of up to 12.8 GB/s. See pages 1-14 to 1-15 for details. PCI ExpressTM interface The motherboard fully supports PCI Express, the latest I/O interconnect technology that speeds up the PCI bus. PCI Express features point-to-point serial interconnections between devices and allows higher clockspeeds by carrying data in packets. This high speed interface is software compatible with existing PCI specifications. See page 1-19 for details. ASUS M2NPV-VM 1-3 Serial ATA 3Gb/s technology The motherboard supports next-generation SATA hard drives based on the new SATA 3Gb/s storage specification. The onboard NVIDIA® nForce 430 MCP southbridge allows RAID 0, RAID 1, RAID 0+1, RAID 5, and JBOD configurations for four SATA connectors. IEEE 1394a support The IEEE 1394a interface provides high-speed and flexible PC connectivity to a wide range of peripherals and devices compliant to IEEE 1394a standards. The IEEE 1394a interface allows up to 400 Mbps transfer rates through simple, low-cost, high-bandwidth asynchronous (real-time) data interfacing between computers, peripherals, and consumer electronic devices such as camcorders, VCRs, printers,TVs, and digital cameras. See page 1-30 for details. HDTV output The motherboard features the NVIDIA® GeForce6150 chipset that supports superior HDTV-out functionality with a higher resolution to 1080i and 720p format, which are clearer than traditional formats allow. ASUS M2NPV-VM motherboard bundles a HDTV-out module that helps you enjoy the highquality scaling and filtering technology. Gigabit LAN solution NVIDIA® Gb LAN controller delivers transfer speeds up to ten times faster than conventional 10/100 Ethernet connections. Gigabit LAN is the networking standard for the early future and is ideal for handling large amounts of data such as video, audio, and voice. USB 2.0 technology The motherboard implements the Universal Serial Bus (USB) 2.0 specification, dramatically increasing the connection speed from the 12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1. See pages 1-24 and 1-29 for details. 1-4 Chapter 1: Product introduction High Definition Audio SoundMAX is the highest performing, most reliable and user-friendly PC audio solution for business professionals, audiophiles, musicians, and gamers. Hear crystal-clear quality from all your audio - MP3 playback, home theatre, advanced gaming, VOIP and more, and never worry - SoundMAX high-definition audio is there to enhance your experience! 1.3.2 Innovative ASUS features ASUS CrashFree BIOS 2 This feature allows you to restore the original BIOS data from the support CD in case when the BIOS codes and data are corrupted. This protection eliminates the need to buy a replacement BIOS chip. See page 2-10 for details. ASUS EZ Flash 2 With the ASUS EZ Flash, you can easily update the system BIOS even before loading the operating system. No need to use a DOS-based utility or boot from a floppy disk. See page 2-6 for details. ASUS O.C. Profile The motherboard features the ASUS O.C. Profile that allows users to conveniently store or load multiple BIOS settings. The BIOS settings can be stored in the CMOS or a separate file, giving users freedom to share distribute their favorite overclocking settings. ASUS Q-Fan 2 technology The ASUS Q-Fan 2 technology smartly adjusts the fan speeds according to the system loading to ensure quiet, cool, and efficient operation. See page 2-33 for details. ASUS M2NPV-VM 1-5 C.P.R. (CPU Parameter Recall) The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P.R. eliminates the need to open the system chassis and clear the RTC data. Simply shut down and reboot the system, and the BIOS automatically restores the CPU default setting for each parameter. ASUS MyLogoTM This feature allows you to personalize and add style to your system with customizable boot logos. See page 2-37 for details. 1-6 Chapter 1: Product introduction 1.4 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. · · Unplug the power cord from the wall socket before touching any component. Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity Hold components by the edges to avoid touching the ICs on them. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component. Before you install or remove any component, ensure that the ATX power supply is switched off or the p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y . Failure to do so may cause severe damage to the motherboard, peripherals, and/or components. · · · Onboard LED The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED. M2NPV-VM ® SB_PWR M2NPV-VM Onboard LED ON Standby Power OFF Powered Off ASUS M2NPV-VM 1-7 1.5 1.5.1 Motherboard overview Motherboard layout 24.5cm (9.6in) PS/2KBMS T: Mouse B: Keyboard PWR_FAN KBPWR ATX12V CPU_FAN DVI PARALLEL PORT DDR2 DIMM_B1 (64 bit, 240-pin module) DDR2 DIMM_B2 (64 bit,240-pin module) DDR2 DIMM_A1 (64 bit,240-pin module) DDR2 DIMM_A2 (64 bit,240-pin module) Super I/O Socket AM2 VGA F_USB12 USBPW12 EATXPWR CHA_FAN1 LAN_USB34 USBPW34 ® GAME FLOPPY PANEL Top:Line In Center:Line Out Bottom:Mic In GeForceTM6150 TV_OUT nVIDIA PCIEX1_1 4Mb BIOS PRI_IDE SEC_IDE CHA_FAN2 M2NPV-VM 88E1116 PCIEX16 ® SATA3 PCI1 TSB43AB22A nForceTM430 SATA1 AD 1986A PCI2 CD AAFP SPDIF_OUT IE1394_1 USB56 USBPW78 USBPW56 CR2032 3V Lithium Cell CMOS Power CHASSIS CLRTC USB78 COM2 COM1 1-8 Chapter 1: Product introduction SATA2 SB_PWR SATA4 nVIDIA ® 24.5cm (9.6in) 1.5.2 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below. 1.5.3 Screw holes Place eight (8) screws into the holes indicated by circles to secure the motherboard to the chassis. Do not overtighten the screws! Doing so can damage the motherboard. Place this side towards the rear of the chassis M2NPV-VM ® ASUS M2NPV-VM 1-9 1.6 Central Processing Unit (CPU) The motherboard comes with a 940-pin AM2 socket designed for the AMD AthlonTM 64 X2/AthlonTM 64/AthlonTM FX/SempronTM processor. The AM2 socket has a different pinout from the 940-pin socket designed for the AMD OpteronTM processor. Make sure you use a CPU is designed for the AM2 socket. The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! 1 . 6 . 1 Installing the CPU To install a CPU. 1. Locate the CPU socket on the motherboard. M2NPV-VM ® M2NPV-VM CPU Socket AM2 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90°-100° angle. Socket lever Make sure that the socket lever is lifted up to 90°-100° angle, otherwise the CPU does not fit in completely. 1-10 Chapter 1: Product introduction