2 User's Manual for 900 MHz Two-Line Cordless Speakerphone 9002 Part 2 Please read Part 1 -- Important Product Information, included in your package. 9002_cover.1AT&T 2 8/12/98, 4:03 PM © 1998 Philips Consumer Communications L.P. All rights reserved. Printed in China. 848233896 Issue 1AT&T 9002_cover.1AT&T 1 8/12/98, 4:03 PM CONTENTS INSTALLATION................................. 3 Table/Desk Installation .......................... 3 Wall Installation ..................................... 5 Belt Clip ................................................ 6 OPERATING RANGE ........................ 14 TELEPHONE MEMORY .................... 15 Storing Memory Numbers ................... 15 Replacing Stored Memory Numbers ... 15 Storing a Pause in a Memory Number . 15 Dialing Memory Numbers ................... 15 Memory Guard .................................... 15 OPERATION..................................... 7 Making a Call ......................................... 9 Answering a Call ................................... 9 Ending a Call ......................................... 9 Redial .................................................... 9 Handset Ringer Selection and Ringer OFF ........................................ 9 Handset Ringer Volume ....................... 10 Base Ringer Volume ............................. 10 Speakerphone Volume ......................... 10 Temporary Tone .................................. 10 Special Telephone Services ................. 11 Hold .................................................... 11 Mute .................................................... 11 Page ..................................................... 11 Intercom ............................................. 11 Conference Calls ................................. 12 Switching a Conference Call to the Base ....................................... 12 Four-Way Conference Calls ................. 12 Headset Jack ........................................ 13 BATTERIES .................................... 16 Charging the Handset Battery Pack ..... 16 Replacing the Handset Battery Pack ... 16 IN CASE OF DIFFICULTY ................. 18 1 9002_book.1AT&T 1 8/12/98, 4:09 PM 2 9002_book.1AT&T 2 8/12/98, 4:09 PM INSTALLATION L1 Standard Electrical Outlet Modular Telephone Jacks Telephone Jacks L2 OR L1/L2 Power cord Telephone line cords Table/Desk Installation 1 Choose a spot near an electrical outlet and a telephone jack. This phone requires a modular telephone jack and a standard electrical outlet (110v AC). This outlet should not be controlled by a wall switch. Install the handset battery. (For an illustration of battery installation, see BATTERIES in this manual.) · Remove the battery cover by pressing on the indentation and sliding downward. · Install the battery pack so that the metal contacts on the bottom of the battery are aligned with the charging contacts in the battery compartment. · Replace the battery cover by sliding it on its track up over the battery compartment until it snaps firmly in place. Set the dial mode. If you have touch tone service, set the switch on the side of the base to TONE. If you have dial pulse (rotary) service, set the switch to PULSE. Even if you have dial pulse service, you can still use telephone services requiring tone signals. See "Temporary Tone" in the OPERATION section of this manual. 2 3 3 9002_book.1AT&T 3 8/12/98, 4:09 PM INSTALLATION 4 Connect the telephone line cord(s) to the base. · If you have a two-line jack, use only the white line cord. Plug one end into the jack labeled L1/L2 on the back of the base. · If you have two separate jacks, use both the white and clear line cords. Insert one end of the white line cord into the jack labeled L1/L2 on the back of the base. Plug one end of the clear line cord into the jack labeled L2 on the back of the base. Connect the telephone line cord(s) to the modular telephone jack(s). · If you have a two-line jack, plug the free end of the white line cord into the modular telephone jack. Make sure the cord snaps firmly into place. · If you have two separate jacks, plug the free end of the white line cord into the modular telephone jack for Line 1. Plug the free end of the clear line cord into the modular telephone jack for Line 2. Make sure the cords snap firmly into place. Connect the power cord. Plug the power adapter into the jack labeled 9V DC on the back of the base. Plug the AC adapter on the power cord into an electrical outlet. Charge the handset batteries for 16 hours. Place the handset face down in the base. The CHARGING light on the base goes on to show the handset is in the right position to charge the batteries. Check for dial tone. After the batteries are charged, press L, and listen for a dial tone. Then press l. If you do not hear a dial tone, turn to IN CASE OF DIFFICULTY in this manual. 5 6 7 8 4 9002_book.1AT&T 4 8/12/98, 4:09 PM INSTALLATION Wall Installation 2-line Wall Jack Wall Mounting Base 1 2 3 4 Follow Steps 1­3 under Table/Desk Installation. Turn the base unit over, and attach the wall mounting base to the lower half of the base unit. Gently press down until it snaps firmly into place. Connect the power cord. Plug the power cord into the power jack on the back of the base. Run the cord under the tab on the bottom of the base and under the tab on the wall mounting base. Plug the AC adapter into an electrical outlet not controlled by a wall switch. Connect the line cord(s). · If you have a two-line jack, use the short white line cord (see illustration above). Insert one end of the short telephone line cord into the telephone jack labeled L1 or L1/L2 on the rear of the telephone base. Feed the excess line cord under the tab on the bottom of the telephone base. Plug the line cord into a two-line wall jack. You will be connected to Lines 1 and 2 -- OR -- · If you have two separate jacks, use the short white line cord, and the long clear line cord. Insert one end of the short white telephone line cord into the telephone jack labeled L1 or L1/L2 on the rear of the telephone base. Feed the excess line cord under the tab on the bottom of the telephone base. Plug the short line cord into the standard one-line wall jack. You will be connected to Line 1. Insert one end of the long clear telephone line cord into the telephone jack labeled L2 on the rear of the telephone base. Feed 5 9002_book.1AT&T 5 8/12/98, 4:09 PM INSTALLATION the excess line cord under the tab on the bottom of the telephone base. Plug the line cord into your other one-line wall jack. You will be connected to Line 2. Mount the telephone on the wall jack. Position the telephone base so the mounting studs on the wall jack fit into the base of the telephone. Slide the telephone down on the mounting studs until the phone locks into place. Follow Steps 7 and 8 under Table/Desk Installation. CAUTION: Use only the AC power adapter supplied with this telephone. Class 2 Power Source. Input: AC 117V, 60 Hz, 9W Output: DC 9V, 500mA 5 6 Belt Clip If you wish, you can attach the belt clip to the cordless handset, following the illustrations below. To Attach To Remove 6 9002_book.1AT&T 6 8/12/98, 4:09 PM OPERATION Send a paging tone to handset/ intercom between base and handset Mute the microphone Put a caller on hold Initiate a conference call Adjust speaker volume PULSE/TONE switch and Line 1 and Line 2 RINGER switches on side of base Line 2 ­ Activate speakerphone End a call Line 1 and Line 2 lights flash when handset or extension is in use Line 1 ­ Activate speakerphone Light goes on when handset is charging in the base Light goes on when base is connected to power Directory Card 7 9002_book.1AT&T 7 8/12/98, 4:09 PM OPERATION Light goes on when intercom is in use Volume HI/LO switch Line 1 ­ Make or answer a call Line 2 ­ Make or answer a call Line 1 and Line 2 buttons flash if base or extension is in use Headset jack Light goes on when handset battery is low End a call Temporary tone Change channel Store and access numbers in telephone memory Connect parties to conference call Begin two-way communication with base Put a caller on hold Redial last number dialed 8 9002_book.1AT&T 8 8/12/98, 4:09 PM OPERATION Making a Call 1 2 Press and release L or l, and wait for a dial tone. The line button of the line you're using lights. When you hear a dial tone, dial the number. Answering a Call Press and release the flashing L or l button on the handset or the base to answer a call on that line. (You can also answer calls on the handset by pressing any key except o.) You can answer calls at the handset or at the base speakerphone. If you are on a call on one line, and wish to answer a call on the other line, press the line key of the new call. The first call is automatically put on hold. To return to the first call, press the line key of that call. Pressing o while you're on a line ends the call on that line. Ending a Call Press o on the handset to end a call on the handset -- OR -- Place the handset in the base to end a call on the handset -- OR -- Press o on the base to end a call at the base speakerphone. Redial The last number dialed on this phone (up to 16 digits) is stored in redial memory until you dial another number. 1 Press L or l on the handset. 2 When you hear a dial tone, press R. Handset Ringer Selection and Ringer OFF You can select from four different handset ringer styles for each line. You can also turn off one or both ringers. 1 Press p, *. 2 Press 1 for Line 1 or 2 for Line 2. 3 Press 1, 2, 3 or 4 to select your ringer style. You will hear a sample of the ringer style -- OR -- Press 0 to turn the ringer off. 4 Press p. 9 9002_book.1AT&T 9 8/12/98, 4:09 PM OPERATION Checking Handset Ringer Selection 1 2 3 4 Press p, *. Press 1 for Line 1 or 2 for Line 2. Press *. You will hear the current ringer style selection. Press o to exit. NOTE: If you're on a call on one line and a call comes in on the other line, you will hear an "alert" tone on your call. Handset Ringer Volume Adjust the handset ringer volume to high (H) or low (L) using the switch on the side of the handset. Base Ringer Volume Line 1 and Line 2 ringers on the base have been assigned different ringing styles. You can adjust the volume of the base ringers to HIGH, LOW or OFF using the switches on the side of the base. Speakerphone Volume Use + and - on the base to adjust the volume of the speakerphone. Temporary Tone NOTE: If you have touch tone service, you do not need to use the Temporary Tone feature. If you have dial pulse (rotary) service, this feature allows you to enter codes or tones needed to operate answering machines, or use electronic banking services, calling cards, and other special services. This feature will operate most special services; however, some services may actually require a touch tone line. To be sure, ask the company that provides the special service. 1 Dial the call, then press *. Any buttons pressed after this send tone signals. 2 After you hang up, the phone automatically returns to dial pulse (rotary) dialing. 10 9002_book.1AT&T 10 8/12/98, 4:09 PM OPERATION Special Telephone Services If you subscribe to special local telephone company services like Call Waiting or Call Forwarding, you can access them by pressing the line button of the line you're currently using whenever you would press the switchhook on a corded phone. This is like the Flash feature on some other phones. Hold 1 2 Press H on the base or the handset to put a call on hold. The light for the line you've put on hold flashes on the handset and on the base. Press the appropriate line button, on either the handset or the base, to return to your call. Mute (Base Only) Mute allows you to hear your caller, but prevents the caller from hearing you. This can be helpful if you are using the base speakerphone in a noisy location. 1 Press M on the base while on a call. 2 To return to your conversation, press M again. Page The Page feature allows you to signal someone at the handset from the base. You can also use this feature to help you locate the handset. Press I on the base. The handset will ring for about 30 seconds. The person at the handset can then press I on the handset to open the intercom connection, or press o to stop the ringing before it stops automatically. Intercom 1 Press I on the handset. The base sounds a tone, and the intercom is open. The person at the base only needs to speak toward the base to answer the handset. To close the intercom connection, press o on either the handset or the base. 2 11 9002_book.1AT&T 11 8/12/98, 4:09 PM OPERATION Conference Calls You can use both lines at the same time to set up a three-way conference call from the handset. 1 Answer or make a call on one line. 2 Press the other line button, and make or answer another call (your first call is automatically put on hold). 3 Press F to connect all parties. Both line buttons are lit during a conferenc ...