PAV-1 AM/FM/MPX RADIO / MONITOR WITH CASSETTE PLAYER, CD CHANGER CONTROLS AND WIRELESS REMOTE CONTROL COMPACT DIGITAL AUDIO O WNER'S MA NUAL WARNING This product should ONLY be installed in accordance with this product's wiring instructions so that the monitor display will be disabled if the parking brake is not applied. The monitor section of this product should ONLY be operated while the transmission of the vehicle is in Park (or Neutral for manual transmission vehicles) and the parking brake is applied. INDEX Page Operating Instructions ................................................................ 1 - 6 Remote Control Operation ......................................................... 7 - 8 CD Changer Controls .................................................................... 9 CD Changer Error Codes ............................................................. 10 Specifications ............................................................................... 11 Care and Maintenance ................................................................. 12 Warranty ....................................................................................... 13 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS the VOL indication on the display panel. To increase the volume quickly, keep the button pressed. To decrease the volume level, press the - side of the control. Keep the button pressed to decrease the volume quickly. During Monitor operation, the display will automatically disappear 5 seconds after the last VOLUME/LEVEL CONTROL (+ / - ) volume or audio level adjustment. This control is also used in To increase the volume level, press the + side of the control. conjunction with the Select button to adjust the bass, treble, The volume will increase and the level will be shown by the bars of balance and fader levels as described in and -1- 1 ON-OFF POWER BUTTON (POWER) 2 Press this button to turn the unit on or off. The unit will also turn on automatically when a cassette is inserted if the ignition is turned "on". 3 4, 5, 6, 7. 3 SELECT BUTTON (SEL) 4 BASS CONTROL 3 This button is used to select the audio function (bass, treble, balance, or fade) to be adjusted using the Level control Pressing the Select button once will set the unit for bass adjustment (BAS indication highlighted on display panel). Pressing the button additional times will select treble adjustment (TRE highlighted on display), balance (BAL) or fader (FAD). The display will automatically return to the normal indication 5 seconds after the last adjustment is made or when another function is activated. 2. response). The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated. To adjust the left-right speaker balance, first select the Balance until the BAL indication mode by pressing the Select button appears on the display panel. Within 5 seconds of choosing the Balance mode, press the - side of the Level control to adjust the stereo balance to the left channel speakers or the + side of the control to adjust it to the right channel speakers. The balance position will be shown by the bars on the display panel from LIIIIIIIIIIIIIIR (full left) to LIIIIIIIIIIIIIR (full right). When the volume level between the left and right speakers is equal, LIIIIIIIIIIIIIR will be shown on the display panel. The display will automatically return to the normal indication seconds after the last adjustment or when another function is activated. 6 LEFT/RIGHT BALANCE CONTROL 3 2 To adjust the front-rear speaker balance, first select the Fader until the FAD indication mode by pressing the Select button appears on the display panel. Within 5 seconds of choosing the Fader mode, press the + or - side of the Level control to TREBLE CONTROL adjust the front-rear speaker levels as desired. The fader To adjust the treble level, first select the Treble mode by press- position will be shown by the bars on the display panel from ing the Select button until the TRE indication appears on the FIIIIIIIIIIIIIIR (full front) to FIIIIIIIIIIIIIR (full rear). When display panel. Within 5 seconds of choosing the Treble mode, the volume level between the front and rear speakers is equal, press the + or - side of the Level control to adjust the treble LIIIIIIIIIIIIIH will be shown on the display panel. The response as desired. The treble level will be shown by the bars display will automatically return to the normal indication 5 on the display panel from a minimum of LIIIIIIIIIIIIIH to a seconds after the last adjustment or when another function is maximum of LIIIIIIIIIIIIIH (LIIIIIIIIIIIIIH represents flat activated. -2- To adjust the bass level, first select the Bass mode by pressing the Select button until the BAS indication is highlighted on the display panel. Within 5 seconds of choosing the Bass mode, to adjust the bass press the + or - side of the Level control response as desired. The bass level will be shown by the bars on the display panel from a minimum of LIIIIIIIIIIIIIH to a maximum of LIIIIIIIIIIIIIH (LIIIIIIIIIIIIIH represents flat response). The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated. 2 7 FRONT/REAR FADER CONTROL 3 5 2 3 2 MODE / BAND SELECTOR (MODE) Each time this button is pressed, the receiver band or input mode is changed as follows: FM à AM à TV à AUX1* à AUX2** à CD CHANGER*** à TAPE**** 8 The indication FM , AM , TV , AUX1 , AUX 2 , CD or TAPE will appear on the display panel according to your selection. * If the AUX1 input has not been disabled during installation. ** If the AUX2 input switch on side of chassis is set to the "ON" position and a compatible Navigation or Rear Observation system is connected. *** If the optional Model PAV-CD 6-disc CD changer is connected. **** If a cassette is loaded in the tape player. NOTE:The TV Receiver Mode is an option that is not available in this model. Although the TV indication will appear on the display panel when cycling through the mode selections, actual TV reception is not possible. MANUAL UP/DOWN TUNING ( / ) AUTOMATIC SEEK TUNING Each momentarily press of the Up Tuning ( ) side of the button will advance the unit one frequency step higher. Similarly, each press of the Down Tuning ( ) side of the button will tune downward. Pressing either side of the button for longer than 0.5 seconds and then releasing will activate the Automatic Seek Tuning function in the selected direction. The radio will seek the next available station and stop at that frequency. The Seek function can be stopped by pressing the button again or activating any other tuning function. -3- 9 MEMORY SETTING BUTTON AUTO-STORE TUNING To set any of the 6 pre-set memories in each of the AM and FM bands, use the following procedure: 1. Turn the unit on and select the desired band. 2. Select the first station to be pre-set using the Manual Up/Down or Automatic Seek Tuning Control 3. Press the Memory Setting button The channel number CH1 will flash; and the audio will be muted. Within 5 seconds while the channel number is still flashing and the audio is still muted, momentarily press the up or down side of the Pre-Set Tuning button to select the channel (CH1 through CH6) that you wish to set. When it appears, press and hold the button until the display stops flashing and the audio returns, indicating that the station is now set into that pre-set memory position and can be recalled at any time by pressing the Pre-Set Tuning button to select the desired number. 4. Repeat the above procedure to enter stations in the remaining pre-set memories on the radio bands. Pressing and holding the Memory Setting button for longer than 2 seconds will activate the Auto-Store Tuning feature which will automatically scan the radio band in use and enter up to 6 strong stations into the pre-set memories. If you have already set the pre-set memories to your favorite stations, activating the AutoStore feature will erase those stations and enter the new strong stations. This feature is most useful when traveling in a new area where you are not familiar with the local stations. bl bm STATION PRE-SET TUNING ( / ) 9. bm. bl bm bn PRE-SET SCAN TUNING (PSCAN) Press and hold the up ( ) or down ( ) side of this button for 2 seconds to scan the 6 stations pre-set into the memories on the AM or FM bands in the selected direction. The unit will stop at each pre-set station for 5 seconds before continuing to the next pre-set station. Press the button again momentarily to stop Pre-Set Scan operation and remain on the selected frequency. display screen. The button is located behind the front panel so the panel must be lowered by pressing the tape Eject button or the Display Angle Control to access it. Each press of the button will change the screen color in the following order: BLUE à GREEN à RED à BLACK bt cq bo LIQUID CRYSTAL DISPLAY PANEL bp DISPLAY COLOR CONTROL bq DISPLAY TINT CONTROL br DISPLAY BRIGHTNESS CONTROL VIDEO MONITOR The Liquid Crystal Display (LCD) panel displays the frequency and activated functions of the radio, tape player and optional CD changer. It also provides the color video monitor function for the auxiliary video input. ) This button is used to set the angle of the display panel for the best viewing. Each tap of the button will adjust the angle by approximately 8° up to the maximum angle. If the button is held, the display will continue to open to the maximum position. Pressing the button when the display is at the maximum angle will return it to the closed position. NOTE:The front panel will automically return to the closed position when the ignition is turned off. bt DISPLAY ANGLE ADJUSTMENT ( These controls are used to adjust the picture quality during auxiliary video input modes. The Color control will adjust the level of color intensity. The Tint control will adjust the level of green or red in the picture. The Brightness control will make the picture brighter or darker. NOTE:The Color and Tint controls are not functional during AM/FM radio, tape and CD changer modes. The Brightness control is functional in these modes. bu DISPLAY RECALL (DISP) cl CASSETTE DOOR The Display Recall function is used to recall the function and volume setting display after they have disappeared from the screen during Auxiliary video input modes. Pressing the button will bring these displays back to the screen for 5 seconds. To access the cassette door, press the Eject button so that the panel drops to its lowered position (this function will operate when the unit is turned off if the ignition switch is "on"). Hold the DISPLAY BACKGROUND COLOR SELECTOR (BGCL) cassette with the exposed tape edge to the right and insert it fully This function is used to select the background color of the into the cassette door until the soft-loading mechanism draws -4- cq bs the cassette in and play begins (the TAPE , cassette symbol, PLAY and direction arrow will appear on the display panel). If the cassette being played requires Metal tape playback equalization, the setting will automatically be selected as indicated by MTL on the display panel. When the cassette reaches the end on the side of the tape being played, the unit will automatically change direction of play as shown by the arrow indications on the display panel. NOTE:Observe cassette operation cautions in Care and Maintenance section of this manual. ) FAST-FORWARD AUTOMATIC MUSIC SEARCH A momentary press of this side of the button will activate the Fast-Forward function which will cause the tape to rapidly move in the forward direction of play (FF and or will appear on the display panel). To stop Fast-Forward movement, press the Fast-Forward button again or the Program Selector and normal play will resume. Pressing and holding the Fast-Forward side of the button for longer than 2 seconds will activate the Fast-Forward Automatic Music Search function (AMS-F and or will appear on the display panel). The unit will automatically fast-forward to the beginning of the next selection and begin play. To stop Music Search function at any point, press the button again or the Program Selector and normal play will resume. cm FAST-FORWARD BUTTON ( ) REWIND AUTOMATIC MUSIC SEARCH A momentary press of this button will activate the Rewind function which will cause the tape to rapidly move in the reverse direction of play (REW and or will appear on the display panel). To stop Rewind movement, press the press the Rewind button again or the Program Selector button and normal play will resume. Pressing and holding the Rewind side of the button for longer than 2 seconds will activate the Rewind Automatic Music Search function (AMS-R and or will appear on the display panel). The unit will automatically rewind to the beginning of the next selection and begin play. To stop Musi ...