MANUAL OWNER'S MANUAL PWR LOUD SEL 4x40 WATTS 1 REL CDC OLUME V + 5 2 3 TUNE 5 DISC TRK 4 AS/PS DISC SEL ACC-60 BAND AUX MO/AUX 1 SCN 2 RPT 3 4RDM 5PGM 6MEM CLR T/F CLK ACC-60 AM/FM/MPX RADIO WITH FOLD-DOWN DETACHABLE FRONT PANEL, 5-DISC COMPACT DISC PLAYER AND QUARTZ CLOCK INSTALL ALLA INSTRUCT INSTALL AT ION INSTRUCT IONS INSTALLATION INSTRUCTIONS This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our toll-free "HELP" line (1-800-645-4994). UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE 1. Remove the detachable front panel to prevent damage to the face and/or controls; use the Release (REL) button to allow the panel to fold down. Then withdraw the panel from the mounting plate. Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it. 2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis. 3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard. 4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (ignition switch must be "on"). If unit does not operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis. 5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place. 6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary. CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration. 7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the unit. INSTALLATION USING KITS 1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit. 2. Wire and test the radio as described in Step 4 above. 3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit. 4. Attach the support strap to the radio and dashboard as described in Step 6 above. 5. Replace the dashboard trim panel. ISO INSTALLATION PROCEDURE This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation. 1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio. 2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame. 3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio. CAUTION: DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE. LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS. 4. Wire the new radio to the vehicle as per step 4 above. 5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1. 2 INSTALL AT ION INSTRUCT IONS INSTALL AT ION INSTRUCT IONS INSTALLAT ION INSTRUCT IONS INSTALL AT ION INSTRUCT IONS INSTALLAT ION INSTRUCT IONS INSTALL ALLA ASSISTA TOLL-FREE INSTALL AT ION ASSISTA NCE The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown (U.S.A. and Canada only). TIME ZONE DAY PACIFIC MOUNTAIN EASTERN CENTRAL MON. - FRI. 8:30AM - 7PM 7:30AM - 6PM 5:30AM - 4PM 6:30AM - 5PM SATURDAY 9AM - 5PM 8AM - 4PM 6AM - 2PM 7AM - 3PM UNIVERSAL INSTALLATION USING MOUNTING SLEEVE SLEEVE ADAPTER PERFORATED SUPPORT STRAP FASTEN THIS END TO SECURE PART OF DASHBOARD BOLT (M4 X 8 MAX) HALF-SLEEVE FASTEN THIS END TO BOLT HOLE IN REAR CENTER OF CHASSIS BEND BOTTOM TABS DOWNWARD BEND TOP TABS UPWARD DASHBOARD 1 2 SLEEVE ADAPTER (REF) HALF-SLEEVE (REF) 1. SLIDE RADIO INTO HALF-SLEEVE. 2. SECURE TO STRAP USING BOLT IF POSSIBLE. 3. REINSTALL ANY ITEMS YOU REMOVED FROM THE DASHBOARD. ISO-DIN FINAL INSTALLATION 1. REMOVE TRIM RING FROM FRONT OF RADIO. 2. MOUNT FACTORY BRACKETS ON NEW RADIO USING EXISTING SCREWS FROM OLD RADIO. 3. SLIDE RADIO AND FRAME INTO DASH OPENING AND SECURE. 4. INSTALL DASH PANELS PREVIOUSLY REMOVED. 3 R A DIO WIRING R A DIO WIRING REFER TO PAGE 5 FOR SPEAKER WIRING 4 SPE A K ER WIRING SPE A K ER WIRING SPEA K ER WIRING SPE A K ER WIRING SPEA K ER WIRING SPEA SPE A K ER WIRING REFER TO PAGE 4 FOR RADIO WIRING WARNING! ! NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 1 SPEAKER. ! NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. ! FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO THE RADIO. 5 OPERA INSTRUCT OPER AT ING INSTRUCT IONS 1 3,4,5,6,7,8 17 31 13,14,15 16,32 28,29 10,18,19 33 2 PWR LOUD SEL 4x40 WATTS 1 REL 11 CDC OLUME V 5 2 3 TUNE 5 DISC TRK 4 AS/PS 9 + DISC SEL ACC-60 BAND MO/AUX 1 SCN 2 RPT 3 4RDM 5PGM 6MEM CLR CLK T/F 30 26 27 20 21 22 23 25 24 12 1 POWER (PWR) BUTTON 2 VOLUME CONTROL Press this button to turn the unit on and off. When the ignition switch is on, the radio will turn on automatically when the CDC, BAND or AUX button is pressed. To increase the volume level, rotate the VOLUME control in the clockwise direction. The volume will increase and the level will be shown on the display panel from a minimum of V -0 to a maximum of V -46 To decrease the volume level, rotate the control in the counterclockwise direction. The display will automatically return to the normal indication 5 seconds after the last volume adjustment or when another function is activated. This control is also used in conjunction with the SEL/LOUD button to adjust the bass, treble, balance and fader levels as described in SELECT (SEL)/LOUD BUTTON This button is used to select the audio function (volume, bass, treble, balance or fade) to be adjusted using the VOLUME control. Pressing the Select button once will set the unit for volume adjustment (VOL will momentarily appear on the display panel, followed a few seconds later by V -- and the setting number). Pressing the button additional times will select bass adjustment (BAS on display panel), treble adjustment (TRE), balance (BAL), fader (FAD), and volume (VOL) again. The display will return to the normal indication 5 seconds after the last adjustment or when another function is for the LOUD activated. Refer to paragraph function of this button. 8 3 4 5 6 7. 6 BASS CONTROL To adjust the bass level, first select the Bass mode by pressing the SEL/LOUD button until the BAS indication appears on the display panel. Within 5 seconds of choosing the Bass mode, rotate the VOLUME Control to adjust the bass response as desired. The bass level will be shown on the display panel from a minimum of B -6 to a maximum of B +6 (B 0 represents flat response). The display will automatically return to the normal indication 5 seconds after the last a d j u s t m e n t o r w h e n a n o t h e r function is activated. 4 5 TREBLE CONTROL To adjust the treble level, first select the Treble mode by pressing the SEL/LOUD button until the TRE indication appears on the display panel. Within 5 seconds of choosing the Treble mode, rotate the VOLUME control to adjust the treble response as desired. The treble level will be shown on the display panel from a minimum of T -6 to a maximum of T +6 (T 0 represents flat response). The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated. OPER AT ING INSTRUCT IONS OPER AT ING INSTRUCT IONS OPERAT ING INSTRUCT IONS OPER AT ING INSTRUCT IONS OPER AT ING INSTRUCT IONS compensate for the characteristics of human hearing. Press and hold the SEL/ LOUD button for at least 2 seconds to activate this feature as indicated by LOUD on the display panel. Pressing the button again for 2 seconds will de-activate the function and LOUD will disappear from the display. 9 AM/FM BAND SELECTOR 6 7 8 During radio play, each time the button is pressed, the radio band changes. The indications AMI, AMII FMI, FMII or FMIII II, II, I II I II III will appear on the display panel accordLEFT/RIGHT BALANCE CONTROL ing to your selection. To adjust the left-right speaker balance, first select the Balance mode by pressing the SEL/LOUD but- During CD play, pressing this button will ton until the BAL indication appears on the display change to radio operation without ejecting the disc. panel. Within 5 seconds of choosing the Balance mode, rotate the VOLUME control clockwise to adUP/DOWN TUNING ( / )/CD TRACK just it to the right channel speakers, or counterclock(TRK) SELECTION wise to adjust it to the left channel speakers. The During radio operation, each time the Up balance position will be shown on the display panel TUNE button ( )is pressed, the radio will from L 12 (full left) to R 12 (full right). When the tune two frequency steps higher. Similarly, volume level between the left and right speak- each press of the Down TUNE button ( ) ers is equal, C 00 will be shown on the display will tune two frequency steps lower. Presspanel. The display will automatically return to ing either button for longer than 1 second the normal indication 5 seconds after the last ad- and then releasing will activate the autojustment or when another function is activated. matic seek tuning function, whereby the radio will seek the next station in the selected FRONT/REAR FADER CONTROL To adjust the front-rear speaker balance, first direction and stop and remain at that freselect the Fader mode by pressing the SEL/ quency. LOUD button until the FAD indication appears on Pressing and holding either button for longer the display panel. Within 5 seconds of choosing than 1 second will cause the radio to conthe Fader mode, rotate the VOLUME control clock- tinue tuning rapidly in the selected diwise or counterclockwise to adjust the front-rear rection until the next available station and speaker levels as desired. The fader position will momentarily stop there. Tuning will continue be shown on the display panel from F 12 (full front) unless the button is released at the desired to R 12 (full rear). When the volume level between station. the front and rear speakers is equal, C 00 will appear on the display panel. The display will auto- During CD player operation, these buttons matically return to the normal indication 5 sec- are used to select a desired track on the onds after the last adjustment or when an- disc. (Refer to Track Select.) other function is activated. AUTO-STORE TUNING (AS) PRE-SET SCAN TUNING (PS) LOUDNESS CONTOUR (LOUD) When listening to music at low volume levels, this Press this button momentarily to scan feature will boost the bass and treble ranges to the 6 stations in the pre-set memories of bl bm 7 OPERA INSTRUCT OPER AT ING INSTRUCT IONS bn STATION PRE-SET MEMORIES the band in use. The unit will stop at each pre-set station for 10 seconds before continuing to the next pre-set station (the frequency on the display panel will flash during Pre-Set Scan operation). Press the button again mom ...