User manual AUDIOVOX DV1532 - Owners Manual

DVD HOME THEATER SYSTEM R CD PLAYBACK 1 VCR AV I N P U T CD-R CD-RW VIEWER OWNER'S MANUAL Important Safety Instructions CAUTION The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to cause an electric shock. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this owner manual. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM CAUTION This product contains a low power laser device. On Placement · · · · The symbol for Class II (Double lnsulation) The apparatus shall not be exposed to dripping or splashing. Do not use the Unit in places which are extremely hot, cold, dusty, or humid. Place the Unit on a flat and even surface. Do not restrict the air flow of the Unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on carpeting. FCC Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. On Safety · When connecting or disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard. · When you are not going to use the Unit for a long period of time, disconnect the AC power cord. On Condensation · When left in a heated room where it is warm and damp, water droplets or condensation may form inside the Unit. When there is condensation inside the Unit, the Unit may not function normally. Let the Unit stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the Unit before use. WARNING: · Should any trouble occur, disconnect the AC power cord and refer servicing to a qualified technician. · Do not place anything directly on the top of the Unit. Damage to the Unit can result. Notes on Copyright It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, rent copyrighted material without permission. Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098 and 4,907,093 licensed for limited viewing uses only. DVD video discs are copy protected, and any recordings made from these discs will be distorted. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. E-1 151AUD1-4_E.pmd 1 4/24/2004, 11:51 AM Important Safety Instructions (For USA) 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like. 6. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer. 6A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. 8. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a book case or cabinet, that may impede the flow of air through the ventilation openings. 9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 11. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of an appliance are not defeated. 12. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. 14. Power Lines - An outdoor antenna should be located away from power lines. 15. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1. 16. Nonuse Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. 17. Object and Liquid Entry - Care should be taken so that objects do not fall, and liquids are not spilled, into the enclosure through openings. 18. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled, into the appliance; or C. The appliance has been exposed to rain; or D. The appliance does not appear to operate normally or exhibits a marked change in performance; or E. The appliance has been dropped, or the enclosure damaged. 19. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. E-2 151AUD1-4_E.pmd 2 4/24/2004, 11:51 AM Table of Contents Important Safety Instruction ..................... 1-2 Disc Formats ................................................ 4 Before You Start ........................................... 5 Using the remote control .......................................... 5 Repeat Playback ................................... 27-28 Repeating a title/chapter (DVD) ............................ 27 Repeating a single track/whole disc (CD) ........... 27 Repeating a specific section (DVD) ...................... 28 Parts and Functions .................................. 6-9 Front Panel ................................................................. 6 Rear Panel....................................................................7 Remote Control ...................................................... 8-9 Playing MP3 and Picture File Disc......... 29-30 Playing a MP3 file disc ............................................ 29 Playing a Picture file disc ....................................... 30 Playing a MP3/Picture file disc ............................... 30 Display .........................................................10 Front Panel Display ...................................................10 Display Information .................................................10 Radio Operation ......................................... 31 Tuning into a station manually ............................... 31 FM Stereo ............................................................. 31 Weak FM stations ............................................... 31 To search for a station automatically ................ 31 Presetting stations ................................................... 31 Tuning into a preset station .................................... 31 Setup ..................................................... 11-16 For better reception ................................................. 11 Connecting a TV .................................................11-12 Connecting a VCR .................................................... 13 Connecting another source .................................... 14 Connecting the speakers & subwoofer .................. 15 Positioning the speakers and subwoofer .............. 16 Mounting rear surround speakers .......................... 16 Turning on the Unit and TV ...................................... 16 Power cord connection ........................................... 16 Customizing the Function Settings ........ 32-40 LANGUAGE setting .................................................. 32 VIDEO setting ............................................................ 33 TV Shape .............................................................. 33 Video Output ....................................................... 34 Brightness ............................................................ 34 Edges .................................................................... 35 AUDIO setting ........................................................... 36 Digital Out ............................................................ 36 L/R speaker .......................................................... 36 Subwoofer ............................................................ 37 Surround Delay...................................................37 Center Delay........................................................38 Pink noise ........................................................... 38 RATING setting ......................................................... 39 Password/Parental Lock..................................... 39 Factory Set .......................................................... 40 Adjusting the Sound ............................. 17-18 Playing a Disc .......................................19-22 Playing Disc ............................................................. 19 Pausing playback (still mode) ............................... 19 Stopping playback ................................................. 19 To skip to a different track ...................................... 19 Fast Foward/Fast Reverse ..................................... 20 Slow-motion play ................................................... 20 Skip (Forward/Reverse) .......................................... 20 Zooming into an image ......................................... 20 Angle selection ....................................................... 21 Audio selection ....................................................... 21 Subtitle selection .................................................... 22 Language Code List for Disc Language ....... 41 Maintenance ................................................ 42 Cleaning Disc .......................................................... 42 Cleaning the Unit ................................................... 42 Important Note ....................................................... 42 Special Functions ................................. 23-25 Display function (DVD) .......................................... 23 Locating a specific title ......................................... 24 Locating a specific title/chapter/track .................. 24 Locating a specific time ......................................... 25 Angle setting ........................................................... 25 Audio setting .......................................................... 25 Subtitle setting ....................................................... 25 Trouble Shooting Guide ........................ 42-43 CD / DVD programmable memory ............... 26 DVD programmable memory ................................. 26 Title/Chapter programmed playback ............. 26 CD programmable memory ................................... 26 Track programmed playback .......................... 26 E-3 151AUD1-4_E.pmd 3 4/24/2004, 11:51 AM Disc Formats The Unit can playback. DVDs [12cm(5") disc] Audio CDs [12cm(5") disc] Compatible Region Management Information Region Management Information: This Unit is designed and manufactured to respond to the Region Management Information that is encoded on DVD discs. If the Region number printed on the DVD disc does not correspond to the Region number of this Unit, this Unit cannot play that disc. The region number of this Unit is 1. 1 Disc Function or Operation that is Not Available When the symbol appears on the TV screen, it indicates that the function or operation attempted is not available at that time. This occurs because the DVD disc manufacturer determines the specific functions. Certain functions may not be available on some discs. Be sure to read the documentation provided with the DVD. Icons Used on DVDs Sample lcons 2 2 1. English 2. French 1. English 2. French Language selections for audio Language selections for subtitles Screen aspect ratio 2 Multiple camera angles Region code indicator Notes: · This Unit supports 2-channel (L/R) audio and 5.1ch (Multi-channel) MPEG Audio 1/2 (only when the DIGITAL AUDIO OUT coaxial jack is used for connection). It does not support 7.1 channel MPEG Audio Version 2.0. · When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images will not be shown. Title, Chapter and Tracks · DVDs are divided into "titles" and "chapters". If the disc has more than one movie on it, each movie would be a separate "title". "Chapters" are sections of titles. · Audio CDs are divided into "tracks". A "track" is usually one song on an Audio CD. Track 1 Track 2 Track 3 Track 4 Track 5 T Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2 Note : · Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some do not. Notes on Unauthorized Discs You may not be able to play back some DVD discs on this Unit if they were purchased from outside your geographic area or made for business purposes. E-4 151AUD1-4_E.pmd 4 4/24/2004, 11:51 AM Before You Start Using the Remote Control · Point the Remote Control at the REMOTE SENSOR located on the Unit. · When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be degraded, causing unreliable operation. · The recommended effective distance for remote operation is about 16 feet (5 meters). To install Batteries 1. Open the battery door. 2. Insert two "AA" or UM-3 size batteries. Battery Replacement When batteries become weak, the operating distance of the Remote Control is greatly reduced and you will need to replace the batteries. Notes: · If the Remote Control is not going to be used for a long time, remove the batteries to avoid damage caused by battery leakage corrosion. · Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable (NICKEL-CADMIUM) batteries. E-5 151AUD5-10_E.pmd 5 4/24/2004, 11:53 AM Parts and Functions Front Panel 1 23 456 7 8 9 10 11 12 13 14 1) 5 Disc tray Open or close tray by pushing OPEN/CLOSE button. Place discs on the disc trays, label side up. 2) STANDBY indicator When the Unit is turned on by pressing the power button, the light will illuminate. If you press the Standby/On button on the remote control, the Unit will turn on. 3) button Turn the power on or off. 4) FUNCTION button Select the source. 5) STOP/BAND button Stop playing a disc./Switch between AM or FM. PLAY/PRESET button Press to start or resume playback. / Preset Tuner memory up. 7) SKIP/TUNING buttons Press SKIP/TUNING button to go back to previous chapters/tracks. Press SKIP/TUNING button to advance to chapters / tracks. Press and hold SKIP/TUNING button to begin fast scan. Four speeds are available. Scan all available radio stations. 6) 8) VOLUME / buttons Change the loudness of the sound from the speakers connected to the Unit. 9) Remote sensor Accept the remote control unit signals. 10) DIGITAL indicator When DOLBY DIGITAL sound is selected, the light will illuminate. PRO LOGIC indicator When DOLBY PRO LOGIC sound is selected, the light will illuminate. 12) Display window Display system information. 13) DISC SKIP button To change next available disc. 14) OPEN/CLOSE button Use to open and close the disc tray. 11) Note: Screen saver - If no button is pressed within 3 minutes, the screen save function will activate, If you want to return to the normal screen, press any button. E-6 (Continued on next page) 151AUD5-10_E.pmd 6 4/24/2004, 11:53 AM Parts and Functions Rear Panel 30 IMP. 6 ohm IMP. 8 ohm 29 28 27 SUBWOOFER CENTER FRONT REAR SPEAKER IMP. 8 ohm REAR FRONT 15 16 17 18 19 20 21 22 24 23 25 26 15) 16) 17) 18) 19) 20) 21) 22) 23) Power cord Right FRONT speaker terminals Right REAR speaker terminals SUBWOOFER terminals Center speaker terminals Left REAR speaker terminals Left FRONT speaker terminals DIGITAL AUDIO OUT jack AUDIO OUT (L/R) jacks 24) 25) 26) 27) 28) 29) 30) S-VIDEO (DVD) output jack FM ANTENNA jacks AM LOOP ANTENNA terminal AUDIO IN (L/R) jacks VIDEO IN (VCR) jack COMPONENT VIDEO jacks (Y, PB/CB, PR/CR) VIDEO OUT jack E-7 (Continued on next page) 151AUD5-10_E.pmd 7 4/24/2004, 11:53 AM Parts and Functions Remote Control 1) STANDBY / ON button Turns the Unit on and puts it in standby mode. 2) RETURN button Return to the normal operation after using the SETUP menu. 3) Number (0 - 9) and (+10) buttons Use when creating programs, and entering a parental level password. To select numbers over 9, press +10 button and then the second no. for example, to enter 18, press +10 and then 8. 4) 5.1 / 2.1 CHANNELS button Switch speaker output to 5.1 channel mode. (All speakers + subwoofer) Switch speaker outputs to 2.1 channel. (Front left/right speakers + subwoofer) 5) MEMORY button Enter the number of a selected chapter or track. Enter the number of a selected station. 6) DIMMER button Adjust the brightness of the front panel display to the level you prefer. 7) PRO LOGIC button In AV_IN mode, switches to Dolby Pro Logic mode for VHS tapes encoded with Dolby Pro Logic. 8) VOLUME (+ / -) buttons Adjust the volume. 9) SETUP button Selects the SET UP menu screen. 10) / CURSOR buttons Use to highlight selections on a menu screen and adjust certain settings. 11) SLOW button Perform slow reverse playback of DVDs. 12) TUNING buttons : Fast reverse playback. : Fast forward playback. TUNING : Scan all available radio stations. 13) STOP button Stop playback. 14) PREV button Move reverse through titles, chapters or tracks on a disc. Tune to the presetted stations. 15) CLEAR button Clear input selections and cancel certain playback functions. 16) DISPLAY (DISP) button Change disc status information displayed on the TV. 17) ANGLE button Switch the camera angle of the video presentation when scenes with multiple camera angles are recorded on a DVD. 18) SUBTITLE button ..... Select one of the subtitle languages programmed on a DVD. E-8 (Continued on next page) STANDBY/ON OPEN/ CLOSE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 SLOW STOP SETUP RETURN FUNCTION GOTO MEMORY DIMMER DISC 1 DISC 4 P. SCAN/ CVBS SOUND DISC 3 DISC 2 DISC 5 PRO LOGIC II VOLUME MENU ENTER SLOW PLAY PAUSE PREV TUNING NEXT CLEAR DISPLAY AUDIO ZOOM/ NTSC/PAL ANGLE SUBTITLE FM MODE BAND A-B DISC REPEAT 151AUD5-10_E.pmd 8 4/24/2004, 11:53 AM Parts and Functions Remote Control 19 STANDBY/ON RETURN FUNCTION OPEN/ CLOSE 19) FUNCTION button Display the FUNCTION screen where you can check or change various setting. 20) OPEN / CLOSE button Use to open or close the disc tray. 21) GOTO button Skip directly to a specific location on a DVD disc. 22) P. SCAN / CVBS button Changing YUV output to Progressive Scan Video mode. 20 GOTO 21 MEMORY DIMMER DISC 1 DISC 4 P. SCAN/ CVBS SOUND DISC 3 DISC 2 DISC 5 22 23 24 23) SOUND button Selects sound balance and tone controls for adjustment with the cursor buttons. 24) DISC 1 - 5 select buttons 25) / CURSOR buttons Use to highlight selections on a menu screen and make adjust certain settings. 26) MENU button Open and close DVD's menu. 27) ENTER button Confirm selections on a menu screen. 28) SLOW 29) 30) button Perform slow forward playback of DVDs. PLAY button Start playback. PAUSE button Pause playback, frame advance. button PRO LOGIC II VOLUME SETUP MENU 25 26 27 28 29 30 31 32 33 34 35 ENTER SLOW SLOW STOP PLAY PAUSE PREV TUNING NEXT 31) NEXT CLEAR DISPLAY AUDIO ZOOM/ NTSC/PAL ANGLE SUBTITLE FM MODE BAND A-B DISC REPEAT Move forward through titles, chapters or tracks on a disc. Tune to the presetted stations. 32) ZOOM button Zoom into an image. NTSC/PAL button Select whether to output the video signal. 33) AUDIO button Select one of the audio soundtracks programmed on a DVD or selects the audio output mode on a AUDIO CD. 34) BAND/REPEAT-DISC button Switch between AM or FM. Repeat chapter or title of a DVD. Repeat single track or whole CD. 35) FM MODE / REPEAT A - B button Set FM MODE to FM STEREO for FM stereo sound or to FM MONO for mono sound. Perform point-to-point repeat playback on a DVD or CD. E-9 151AUD5-10_E.pmd 9 4/24/2004, 11:53 AM Display Front Panel Display Disc indicator Displayed during disc playback. TUNER indicator Displayed during TUNER mode. Main display section Indicates the operation status of the disc and Unit. STEREO indicator Tune into a station. "((ST))" will appear when an FM broadcast is in stereo. AUX indicator Displayed when connecting other audio equipment. REPEAT 1 playback indicator Displayed during repeat a CD playback. Disc 1 - 5 indicator The disc number appears when a certain disc is playing. MEMORY indicator Displayed during programmed playback. Display Information The DVD displays the information shown below on the TV screen and on the Unit's DVD display depending on the operation status. Display Examples TV Screen If no disc is loaded when the Main Unit is switched on. Tray open Tray closed Loading Stopped Playing Paused Fast forward Fast reverse Slow Repeat A - B / Unit Display No Disc Remarks " " appears when the tray is closed and: 1)There is no disc in the tray. 2)The disc type is not playable in this Unit. 3)The disc is not loaded correctly (upside-down, etc.) Loading... Stop Play The display changes to show other indicators. Freezes the image on the screen or pauses audio playback. The display changes to show other indicators. Does not function for Audio CDs. Repeat a specific section. The operation is not permitted by the DVD Unit or the disc. Pause x2 x2 x 1/2 Rep A- Rep A-B Region (Local) Number Error Indicator If the region (local) number of the disc that you attempt to play differs from the region number of the Unit, "Invalid Region" appears on the TV screen. (The disc cannot be played). E - 10 151AUD5-10_E.pmd 10 4/24/2004, 11:53 AM Setup For better reception FM Connect FM antenna (included) to the FM ANTENNA jacks. AM Connect the loop antenna (included) to the AM LOOP ANTENNA terminals. FM antenna IMP. 6 ohm IMP. 8 ohm SUBWOOFER CENTER FRONT REAR SPEAKER IMP. 8 ohm REAR FRONT To wall outlet AM(MW) LOOP ANTENNA (SUPPLIED) A.Connecting a TV The Unit can be connected to your TV in several different ways, depending on the design of your TV. RCA Audio/Video Jacks Use the supplied Audio/Video cable. 1. Connect the VIDEO OUT and left/right AUDIO OUT jacks to the VIDEO IN and left/right AUDIO IN jacks on your TV. Note: · If you want the sound come from the speakes of the Main Unit, you need not to connect the left/right AUDIO OUT jacks from the Main Unit to your TV. or S-Video Jack Use an S-Video cable (not supplied) and the Audio cable (not supplied). 1. Use an S-Video cable to connect the S-VIDEO (DVD) jack on your Unit to the S-VIDEO IN jack on your TV. 2. Use the Audio cable to connect the left/right AUDIO OUT jacks on the unit to the left/right AUDIO IN jacks on your TV. E - 11 (continued to next page) 151AUD11-18_E.pmd 11 4/26/2004, 11:06 AM Setup or Component video outputs (DVD) Some TVs or monitors are equipped with component video inputs. Using the Audio cable (not supplied), connect the left/right AUDIO OUT jacks on your Unit to the left/right AUDIO IN jacks on your TV and the Component video cable (not supplied), connect the Green plug Y VIDEO OUT jack on your Unit to Y VIDEO IN jack on your TV, the Blue plug PB/CB VIDEO OUT jack on your Unit to PB/CB VIDEO IN jack on your TV and the Red plug PR/CR VIDEO OUT jack on your Unit to PR/CR VIDEO IN jack on your TV to view the higher quality picture playback. Progressive outputs (DVD) Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video signal. Using the Audio cable (not supplied), connect the left/right AUDIO OUT jacks on your Unit to the left/right AUDIO IN jacks on your TV and the Component video cable (not supplied), connect the Green plug Y VIDEO OUT jack on your Unit to Y VIDEO IN jack on your TV, the Blue plug PB/CB VIDEO OUT jack on your Unit to PB/CB VIDEO IN jack on your TV and the Red plug PR/CR VIDEO OUT jack on your Unit to PR/CR VIDEO IN jack on your TV to enjoy highest quality picture with less flicker. Connect the component video cable to TV, press SETUP button and select Video Output to YUV (see page E-34 for setting of Video Output). To select the output signal for better picture quality, press the P. SCAN button on the remote control when DVD is stopped. Notes: · When progressive output is activated, no video signal output from S-video and RCA (CVBS) video jacks. · Make sure your TV supports progressive scan component video signal, press the P. SCAN button twice until "CVBS" display for going back CVBS video signal. or Coaxial Antenna Jack Some TVs do not have an RCA or S-Video jack, they only have a coaxial antenna jack. In order to connect this Unit to these TVs, you must purchase an RF modulator (available in the Audio/Video department of most electronics retailers or at http://www.18002526123.com) and follow the instructions included with it. Notes : · Connect the Unit to your TV directly. If you connect the Unit through a VCR, the playback picture will be distorted because DVD discs are copy protected. · When you connect the Unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connection. · Refer to the instruction manual of the connected equipment as well. E - 12 (continued to next page) 151AUD11-18_E.pmd 12 4/26/2004, 11:06 AM Setup B. Connecting a VCR 1. Using the supplied Audio/Video cable, connect the yellow plug from VIDEO OUT jack on your Unit to VIDEO IN jack on your TV, connect the left/right AUDIO OUT jacks on your Unit to left/right AUDIO IN jacks on your TV. If you want the sound come from the speakers of the Main Unit, you need not to connect the left/right AUDIO OUT jacks from the Main Unit to your TV. 2. Using the Video cable (not supplied), connect the VIDEO IN (VCR) jack on your Unit to VIDEO OUT jack on your VCR. 3. Using the Audio cable (not supplied), connect the left/right AUDIO IN jacks on your Unit to the AUDIO OUT jacks on your VCR. · An adaptor can be bought locally to connect the round RCA-style plugs to a socket. For the TV get a scart INPUT adaptor. For the VCR get a scart OUTPUT adaptor. To hear the sound from television programmes through the Unit Sound from the television does not go to the speakers of the DVD amplifier Unit with the suggested connections. To hear sound from television programmes through the DVD amplifier's loudspeakers you need to use your video recorder as a television tuner. To do this follow these steps: 1. Connect up the VCR as above in "Connecting a VCR". If your television does not have the round (RCA-style) connectors you can get an RCA to scart input adapter. 2. Press the FUNCTION button on the DVD Amplifier Unit to get AV_IN mode, shown on the front panel display. 3. On the television, select the AV or scart input channel for the DVD amplifier Unit. 4. On the VCR, select the television programme you want to watch. 5. On the DVD amplifier Unit select normal stereo or Pro Logic decoder modes according to your preference. · Please refer to the AV_IN rows of the table on page 18 describing which speakers the sound will come out of. · When using the VCR as a television tuner, you cannot watch one programme while recording another. Watching a DVD 1. Turn on the Unit, use the FUNCTION button on the remote control or the front panel to select "DVD". 2. Turn on your TV and follow the instructions included with it to select the VIDEO input which corresponds to the VIDEO IN jack that is connected to the Unit. Watching a Videotape 1. Turn on the Unit, use the FUNCTION button on the remote control or the front panel on the front panel to select "AV_IN". 2. Turn on your TV and follow the instructions included with it to select the VIDEO input which corresponds to the VIDEO IN jack that is connected to the Unit. 3. Turn on the VCR and follow the instructions included with it to play the videotape. Note: · When playback VCR, if you want the sound comes from the speakers (supplied), you need not to connect the Video cable. · If VCR Audio is mono, surround speakers sound level will be low. E - 13 (continued to next page) 151AUD11-18_E.pmd 13 4/26/2004, 11:06 AM Setup C. Connecting another source Analogue connection Using the Audio cable (not supplied), connect the left/right AUDIO OUT jack on your Unit to the AUDIO IN jack on the other analogue equipment. Digital connection Using the Coaxial Digital Audio cable (not supplied), connect the DIGITAL AUDIO OUT on your Unit to the DIGITAL AUDIO IN jack on your another equipment. Listening to another audio equipment 1. Turn on the Unit. 2. Turn on your audio equipment and follow the instructions included with it to select the AUDIO IN or DIGITAL IN function. Notes: · When you connect the Unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connection. · If the external equipment is a television and this audio system is closed to it, you may experience interference if the tuner function is selected while the television is working. · When you have selected TUNER function, sound will ONLY come from the front left, right speakers and subwoofer. · If you have a stereo VCR, make sure you set it in stereo mode. · Due to copyright protection, DVD movies cannot be copied. If you copy a DVD movie onto a videotape, the resulting copy will be unclear, with poor sound quality. This is NOT caused by a defective DVD system. · Refer to the instruction manual of the connected equipment as well. E - 14 (continued to next page) 151AUD11-18_E.pmd 14 4/26/2004, 11:06 AM Setup D. Connecting the speakers & subwoofer 1. The speaker cords have been color-coded to simplify connection. Just plug the POSITIVE (+) and NEGATIVE (-) ends of each speaker wire into the corresponding jacks on the rear of the Unit, matching the color tube on the end of the speaker wire to the color-coded connector. 2. The front left/right and rear left/right speakers are all the same. However, make sure you connect to the center speaker which is slightly longer than the rest. E - 15 (continued to next page) 151AUD11-18_E.pmd 15 4/26/2004, 11:07 AM Setup E. Positioning the speakers and subwoofer FRONT SPEAKERS Place on both sides of the TV, equal distances apart. CENTER Place on the top of or below the TV. REAR SPEAKERS Place right beside or slightly behind your listening position, and a little higher than your ears. SUBWOOFER Can be placed anywhere. Mounting rear surround speakers 1) Mark the correct mounting position on the wall. 2) Insert a fixing screw(s) at the marked position on the wall. 3) Align the slot hole(s) of the speaker over the screw and pull the speaker downward until it is firmly hooked. Need More Help? DO NOT RETURN THIS TO THE STORE Please call Customer Service at 1-800-252-6123 or visit online help at http://www.18002526123.com Turning on the Unit and TV 1)Press the power button to turn the Unit ON, or Y 2)Press the STANDBY/ON button on the remote control or the FUNCTION button or the PLAY button to turn on the Unit while the Unit is in standby mode. 3)Turn on the TV by pressing its POWER button. 4)Select the channel on your TV corresponding to the VIDEO IN jack that the Unit is connected to. See TV User guide for more information. · If you have connected the Unit successfully, the DVD logo (start-up picture) will appear on your TV screen. Note: · Whenever no disc or disc stop for about 30 minutes, the system will be turned to POWER standby mode automatically. · The green LED of Standby will be turned on while the unit is at standby mode. Power cord connection · · · · Make sure that all the components and speakers are connected correctly. To prevent electrical shock, match wide blade of plug to wide slot, fully insert. Be sure the AC power cord is disconnected and all functions are off before making connections. When you are not going to use the Unit for a long period of time, disconnect the power cord. E - 16 (continued to next page) 151AUD11-18_E.pmd 16 4/26/2004, 11:07 AM Adjusting the Sound To adjust the surround sound balance while Dolby Digital and Pro Logic II decoding is in effect Use the remote control to make the following changes to speaker balance: Front speaker (left) · Press the SOUND button repeatedly to display LEFT, then press the or CURSOR button to adjust the sound level. It will show on the display of the Unit. Front speaker (right) · Press the SOUND button repeatedly to display RIGHT, then press the or CURSOR button toadjust the sound level. It will show on the display of the Unit. Center speaker · Press the SOUND button repeatedly to display CENTR, then press the or CURSOR button to adjust the sound level. It will show on the display of the Unit. Rear speaker (left) · Press the SOUND button repeatedly to display REARL, then press the or CURSOR button to adjust the sound level. It will show on the display of the Unit. Rear speaker (right) · Press the SOUND button repeatedly to display REARR, then press the or CURSOR button to adjust the sound level. It will show on the display of the Unit. Subwoofer · Press the SOUND button repeatedly to display SUB, then press the or CURSOR button to adjust the sound level. It will show on the display of the Unit. Note : · If you do not press any button within a few seconds, the display will return to normal. To adjust the sound quality Press the SOUND button repeatedly to select an equalization mode (BASS and TREBLE). Press the to adjust the sound level. BASS : the low range of sounds TREBLE : the high range of sounds Bass and treble control the sound from the front left and right speakers. Dolby Digital Dolby Digital is a sound system developed by Dolby Laboratories Inc. that gives movie theatre ambience to audio output when the Unit is connected to a Dolby Digital 5.1 channel processor or amplifier. This Unit automatically recognizes DVDs that have been recorded with Dolby Digital. Not all Dolby Digital sources are recorded with 6 channels. Some sources marked Dolby Digital may be recorded in Dolby Surround, a 2 channel system. Look for this logo on your DVD Unit. Dolby Pro Logic II creates five full-bandwidth output channels from two-channel sources. This is done using an advanced, high-purity matrix surround decoder that extracts the spatial properties of the original recording without adding any new sounds or tonal colorations. or CURSOR button Movie Mode (MOVIE) The Movie mode in Pro Logic II is very similar to that of the original Pro Logic decoder. The main difference is that it has stereo surround channels and no surround filter, unlike Pro Logic which has a mono surround channel and a 7 kHz surround filter. Movie mode is the standard required for all A/V systems. When an autosound unit has a video screen, it is also considered an A/V system. It can be called simply "Pro Logic II". Music Mode (MUSIC) The Music mode offers users some flexibility to control the end results to their own taste. Music mode should not be used with THX audio processing mode. Music mode is recommended as the standard mode for autosound music systems (without video), and is optional for A/V systems. It is recommended that Music mode be identified as the "Music" version of Pro Logic II, to distinguish it from the Movie mode. E - 17 (continued to next page) 151AUD11-18_E.pmd 17 4/26/2004, 11:07 AM Adjusting the Sound Pro Logic Emulation Mode (PL II and EMU) The Pro Logic emulation mode offers users the same robust surround processing as original Pro Logic, in case the source content is not of optimum quality, or if there is a desire to hear the program more "as it used to be". When this mode is used, it is called Pro Logic, as before. There is no "Pro Logic I" mode. The Pro Logic emulation mode is optional. Dolby does not require PLII products to use the original Pro Logic decoding algorithm. However, if the DSP contains the original Pro Logic code, and if the product maker would like to use it, this is quite acceptable and even encouraged. A product must not offer both original Pro Logic and the Pro Logic emulation mode. Matrix Mode (MATRX) The Matrix mode is the same as the Music mode except that the directional enhancement logic is turned off. It may be used to enhance mono signals by making them seem "larger". The Matrix mode may also find use in auto systems, where the fluctuations from poor FM stereo reception can otherwise cause disturbing surround signals from a logic decoder. The ultimate "cure" for poor FM stereo reception may be simply to force the audio to mono. Manufactured under license from Dolby Laboratories. 'Dolby' , 'Pro Logic' and the double-D symbol are trademarks of Dolby Laboratories. "DTS" and "DTS Digtial Out" are trademarks of Digital Theater Systems, Inc. To select the listening channel 1. When the disc is stopped, you can press the 5.1/2.1 CH button on the remote control to select different speakers output status shown on below table. 2. At AV IN function mode, you also can press the PRO LOGIC II button repeatedly on the remote control to select PRO LOGIC II (indicator on the front panel of display will illuminate). 3. You can active or off subwoofer output by setup menu. Notes: · The wording "2.1 CH" will be corresponded to the audio/sound output from Front Left and Front Right speakers plus the Subwoofer. · 5.1/2.1 CH button is no response to JPG CD-ROM or JPG/MP3 CD-ROM. Please select 5.1/2.1 CH output before putting such CD-ROM. · Dolby Digital 5.1 CH will not be activated on Pro Logic II. The following table shows which speakers are working in the various modes. FUNCTION DIS C S 5.1 / 2.1 CH Button L/R S P EAKER (SMALL/ LARGE) SM A LL 5.1CH DVD / CD 2.1CH 5.1CH MP 3 2.1CH --5.1CH PCM DVD LARGE --SM A LL LARGE --DVD M ODE ----------SM A LL 2.1CH ----LARGE --TUNER AV_IN ------SM A LL LARGE --- SUBWOOFER ON/OFF ON ON OFF ON ON OFF --ON OFF ON OFF ON ON OFF --ON ON OFF Dolby P ro Logic II S e le c tion EMU 5.1 5.1 5 2.1 2 2 5.1 2.1 2 5.1 5 2.1 2 2 2.1 5.1 5.1 5 M A T R IX 5.1 5.1 5 2.1 2 2 5.1 2.1 2 5.1 5 2.1 2 2 2.1 5.1 5.1 5 MUSIC 5.1 5.1 5 2.1 2 2 5.1 2.1 2 5.1 5 2.1 2 2 2.1 5.1 5.1 5 M O V IE 5.1 5.1 5 2.1 2 2 5.1 2.1 2 5.1 5 2.1 2 2 2.1 5.1 5.1 5 BY PASS 5.1o r 2.1 5.1o r 2 5 or 2 2.1 2 2 5.1 2.1 2 5.1 5 2.1 2 2 2.1 5.1 2.1 5 D o lby P ro Lo gic II no t applied on Tuner, M P 3 and P C M DVD. 5.1 - Represents FRONT LEFT/RIGHT, REAR LEFT/RIGHT, CENTER speakers and SUBWOOFER 2.1 - Represents FRONT LEFT/RIGHT speakers and SUBWOOFER 5 2 - Represents FRONT LEFT/RIGHT, REAR LEFT/RIGHT and CENTER speakers - Represents FRONT LEFT/RIGHT speakers E - 18 151AUD11-18_E.pmd 18 4/26/2004, 11:07 AM DVD CD Basic playback Playing a Disc This owner's manual explains the basic instructions of this DVD Unit. Some DVD discs are produced in a manner that allows specific or limited operation during playback. As such, the DVD Unit may not respond to all operating commands. This is not a defect in the DVD Unit. Refer to the instruction notes of discs. " may appear on the TV screen during operation. A " " means that the desired operation is not " permitted by the DVD Unit or the disc. Turning on the unit Press the power button on the front panel, the STANDBY indicator will light up. Then select the desired function by pressing the FUNCTION button. Note: Remote control can turn on the unit only if the unit is in standby mode. WARNING BEFORE TRANSPORTING THE UNIT, TAKE OUT ALL DISCS FROM DISC TRAY. To turn off the unit Press the power button on the front panel, the unit will be turned off and the display will go dark. If you press STANDBY/ON button on the remote control to turn off the unit, it will bring the unit to standby mode. . Playing a Disc 1. While the unit is in standby mode, press FUNCTION button to select DVD mode. It will take a while for disc holder automatically rotating to load disc 1. 2. If the display shows "Load" or "NO DISC", press the OPEN / CLOSE button. The disc tray opens. . 3. Press DISC 1 - 5 select button on the remote control, after a while, the disc tray will automatically close and then open. Disc holder will automatically rotate one cycle and stop. 4. Place the first disc on the disc holder with the label side up. 5. Press DISC 1 - 5 select button on the remote control or DISC SKIP button on the front panel to rotate disc holder to load other discs. . 6. Press the OPEN / CLOSE button. The disc tray closes. It takes a short while for your unit to load the discs. After loading, for some discs, the unit will automatically start playback of the disc. 7. Press the PLAY button. 8. Press DISC 1 - 5 select buttons or DISC SKIP button on the front panel to select other disc playback. Notes: · Use the OPEN / CLOSE button on the front panel to open or close the disc tray. Do not push the disc tray or you may damage the Unit. · Let the disc tray open completely before removing the discs. Press the OPEN / CLOSE button to close the disc tray after you remove the discs. · If you use the OPEN / CLOSE button on the front panel to open the disc tray, the unit will stop playing. The disc holder will rotate half circle so that the disc can be taken out. If you use the OPEN / CLOSE button on the remote control to open the disc tray , the playback will not be affected. Pausing playback (still mode) Press the II PAUSE button. To resume normal playback, press the PLAY button. Y Stopping playback Press the STOP button at the location where you want to interrupt playback. To resume playback at the position where the disc was stopped, press the PLAY button. Y If you press the STOP button twice, the Unit's memory will be cleared and pressing the PLAY button will reset the disc to the beginning. To skip to a different track · Press the SKIP button once to skip to the start of the previous track. · Press the SKIP button to skip to the next track. · For audio CD disc, use the number buttons (remote control only) to jump straight to that track number. Notes: · During playback, disc tray can be opened/closed to add disc and the current disc playback will not be interrupted (only by pressing OPEN / CLOSE button on the remote control). · The / (SKIP) buttons can only be used to choose a track of the current disc. To choose a track of another disc, DISC 1 - 5 select buttons or DISC SKIP button should be pressed to get to the desired disc first. E - 19 (continued on next page) 151AUD19_E.pmd 19 4/26/2004, 11:12 AM Playing a Disc Fast Forward/Fast Reverse DVD CD or TUNING button when a disc is playing. 1. Press the TUNING · The disc begins fast scan at x2 speed. or TUNING · Four speeds are available. Each time TUNING button is pressed, the speed of fast scan changes in the following sequence: Note : You also can press speed. 2. Press the SKIP/TUNING button on front panel repeatedly to select different fast scan PLAY button when you reach the desired point to resume playback at normal speed. Y Slow-motion play DVD or SLOW button in the play mode. W . 1. Press the SLOW · Two speeds are available. Each time SLOW or SLOW button is pressed, the speed of slow-motion W playback changes in the following sequence: 2. Press the PLAY button to return to the normal playback speed. Y SKIP (Forward / Reverse) DVD CD While you are playing a disc, press the NEXT button of the remote or SKIP/TUNING button of front panel to move to the beginning of the next chapter or track. Press the PREV button of the remote or SKIP/TUNING button of the front panel to move to the previous chapter or track and automatically start playing it. Zooming into an image While a disc is playing, press the ZOOM/NTSC/PAL button. · While an image is zoomed, you can use , , and button to shift the view and display the part you want. · To return to the normal view, press the ZOOM/NTSC/PAL button until the " off " symbol shows. The screen will return to normal. · When you reach the edge of the image, the display will not shift anymore in that direction. E - 20 151AUD20-28_E.pmd 20 (continued on next page) 4/26/2004, 11:34 AM DVD Playing a Disc Angle selection Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the same scene can be viewed from each of these different angles. 1. While you are playing a DVD with different angles recorded, press the ANGLE button to view the number of the current angle. 2. Press the ANGLE button repeatedly to change the scene to the next angle in those recorded. · About two seconds later, playback continues from the new angle you selected. · If no button is pressed within 10 seconds, playback continues without changing the current angle. Sequence of angle shots (Example) Notes: · This function can only be used for discs on which scenes shot from multiple angles have been recorded. · If only one angle is recorded, " 1/1 " is displayed. Audio selection On some discs, the sound is recorded in two or more formats. Follow the directions below to select the type of playback. 1. While a disc is playing, press the AUDIO button to show the current audio format number. 2. Press the AUDIO button repeatedly to select the desired audio format. Notes : · If only one audio format is recorded, the number does not change. · About two seconds later, playback continues in the new audio format. E - 21 151AUD20-28_E.pmd 21 (continued on next page) 4/26/2004, 11:34 AM DVD Playing a Disc Subtitle selection 1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as shown in the example below. 2/3 Spa Recorded language changes sequentially. (The maximum number of possible subtitles is 8) 2. Press the SUBTITLE button repeatedly to select the desired subtitle language. Notes : · If only one language is recorded, the language does not change. · About two seconds later, playback continues with the new subtitle you selected. · The number of languages recorded differs depending on the disc. · If no button is pressed within a few seconds, playback continues without changing the current subtitle. · This function can only be used for discs on which subtitles have been recorded in multiple languages. · On some DVDs, subtitles are activated from the main menu of the DVD. Press the MENU button to activate the main menu. E - 22 151AUD20-28_E.pmd 22 4/26/2004, 11:34 AM DVD Basic playback Special Functions DISPLAY function Using DISPLAY, you can check and change the current settings of the following items: ANGLE, AUDIO and SUBTITLE. · While the disc is playing, press the DISPLAY button to display the screen shown below. Elapsed time: Elapsed time from the beginning of the chapter which is currently playing. Remaining time: Remaining time of the title which is currently playing. Elapsed Time Remaining Time · Press the DISPLAY button twice to display the screen shown as below. · Press the ANGLE, AUDIO and SUBTITLE button to change the selected item. Chapter Title Audio setting Subtitle setting Angle setting Time Title skip · The number of the title currently playing and total titles of disc. · Press the GOTO button to set your desired title, then press the ENTER button to confirm. Chapter skip · The number of the chapter currently playing and total chapters of the currently played title. · Press the GOTO button to set your desired chapter, then press the ENTER button to confirm. Time skip · Elapsed time from the beginning of the currently playing chapter and the remaining time from the beginning of the currently playing title. · Press the GOTO button to set your desired point to start playback, then press the ENTER button to confirm. Angle setting · The current angle is displayed. When a disc with only one angle is played back, " · Press the ANGLE button to select the desired angle. Angle 1/1" is displayed. Audio setting · The type of audio currently selected is displayed. · Press the AUDIO button to select your desired type of audio. Subtitle setting · The subtitle number and language currently selected is displayed. When a disc with only one subtitle is played back, " 1/1 Eng " is displayed. · Press the SUBTITLE button to select your desired language. GOTO function This function allows you to skip directly to any part of the disc while a disc is playing. Note : · After settings, press the DISPLAY button again to return to the normal screen. E - 23 151AUD20-28_E.pmd 23 (continued on next page) 4/26/2004, 11:34 AM Basic playback Special Functions DVD Locating a specific title If a DVD disc contains title numbers, you can locate a specific title by directly selecting a title number. 1. In stop mode, press the GOTO button. 2. Press , or button to highlight a specific field and press the corresponding number button(s) for the title you want. 3. Press the ENTER button to confirm. The Unit will start playback about 3 seconds later. Note : · Pressing the CLEAR button resets the title number. Locating a specific title / chapter / track DVD CD