General Mobile Radio Service (GMRS) Model : GMRS862 Twin Pack Owner's Manual HI LO MODE VOX S Customer Service 1-800-290-6650 Released: 1-13-06 128-7625 1 of 28 THIS PAGE LEFT BLANK INTENTIONALLY 2 128-7625 2 of 28 CAUTION SAFETY INFORMATION Your wireless hand-held portable transceiver contains a low power transmitter. When the PTT button is pushed (or the VOX mode is enabled) it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for hand-held wireless devices. Important: To maintain compliance with the FCC' s RF exposure guidelines hold the transmitter at least 1 inch (2.5 centimeters) from your face and speak in a normal voice, with the antenna pointed up and away. If you wear the handset on your body while using the headset accessory, use only the Audiovox supplied carry clip for this product and ensure that the antenna is at least 1 inch (2.5 centimeters) from your body when transmitting. Use only the supplied antenna. Do not use your transceiver with a damaged antenna. Unauthorized antennas, modifications, or attachments could damage the transmitter and may violate FCC regulations. Performance: Your transceiver will only achieve its maximum operating range when communicating with other transceivers across open and flat areas or between elevated points. Normally occurring environmental factors such as buildings, trees, terrain and weather, or interference from other radio or electrical equipment, may have adverse effects on the transceiver's effective range. These are not indicative of a fault condition. Avoid placing the GMRS862 radio transceiver for prolonged periods of time in direct sunlight or temperatures below -4°F(-20°C) or above 140°F (60°C). Place the rubber cover on jacks when not in use. 3 128-7625 3 of 28 WARNINGS: Battery Care Never attempt to charge alkaline or dry cell batteries, as batteries may burst causing personal injury and damage to the product. If rechargeable batteries are used, such as Nickel Metal Hydride (NiMH), use only Audiovoxapproved rechargeable batteries. Use of an Audiovox charger with other brands of batteries is not recommended, as battery charging times will vary with different brands. Refer to the Manufacturer's instructions for charging other brands of batteries. Battery Disposal In general, if handled improperly, batteries pose a risk of fire or burns. Do not disassemble, crush, puncture, short external contacts, or dispose of the batteries in fire or water. Dispose of the batteries in a environmentally safe manner and recycle whenever possible. FCC WARNING Replacement or substitution of transistors, diodes or other parts of a unique nature, with parts other than those recommended by the manufacturer, may cause a violation of the technical regulations of Part 15 of FCC Rules. GMRS LICENSE: USE OF THIS RADIO WITHIN THE UNITED STATES REQUIRES AN FCC GMRS LICENSE. AN INDIVIDUAL 18 YEARS OF AGE OR OLDER, WHO IS NOT A REPRESENTATAIVE OF A FOREIGN GOVERNMENT, IS ELIGIBLE TO APPLY FOR A GMRS SYSTEM LICENSE. YOU WILL NEED TWO FORMS FROM THE FCC: FCC FORM 159, AND FCC FORM 605 (MAIN FORM AND SCHEDULE F). YOU CAN FIND THE FORMS ONLINE AT: HTTP://WWW.FCC.GOV/FORMPAGE.HTML, OR CALL 1-800-418-3676. 4 128-7625 4 of 28 Model GMRS862 (FCC License Required) 6 5 4 3 2 1 8 11 12 9 7 1 (REF) 1. 2. 3. 4. Battery Cover Monitor (M) Button Detachable Carry Clip Push-To-Talk (PTT) and Function Confirmation Button 5. Antenna 6. External Microphone (MIC)/Charger (CHG)/Speaker (SP) Jack 5 3 (REF) 10 13 14 7. Built-in Speaker 8. Liquid Crystal Display (LCD) 9. Built-in Microphone 10. Up Channel/Volume Button 11. Down Channel/Volume Button 12. MODE/VOX Button 13. Power On/Off and SCAN Button 14. Battery Charging Contacts 128-7625 5 of 28 Model GMRS862 DISPLAY 1 2 3 9 4 5 10 11 HI LO 6 7 8 1. Roger Beep Tone Indicator: This icon appears when the Roger Beep tone is on, and disapppears when the tone is not in use. 2. Transmit Indicator: Icon appears when the unit is in the transmit mode (PTT button activated or VOX mode active). 3. Busy Indicator: This icon appears when the unit is receiving a transmission. 4. Large Segment Display: Indicates the channel number in use between 1 and 22. 5. Scan Indicator: This function allows the user to scan a channel every 0.5 second to search for a valid signal. 6. HI/LO Indicators: Appropriate icon appears when the transmit power is set to desired output power for a specific channel. 7. Battery Level Indicator: Icon indicates the battery charge level. 8. Small Segment Display: Indicates the CTCSS tone code (1-38) function is active for the main channel in use. 9. Monitor Indicator: This function is not used. 10.Key Lock Indicator: This function is not used. 11. Voice Activated Transmission (VOX) Indicator: This function allows hands-free conversation. The icon appears when the VOX mode is activated. 6 128-7625 6 of 28 Equipment and Accessories Supplied 1. 2. Radio (2) Owner's Manual (1) GMRS862 128-7625 Powering the transceiver: Your GMRS862 radio transceiver operates on four AAA Alkaline batteries. Alkaline batteries will provide slightly better performance than rechargeable batteries. Only Audiovox approved rechargeable batteries should be recharged in the radio transceiver. Use of optional Audiovox charging equipment with other brands of rechargeable batteries is not recommended as battery charging times will vary. Refer to the manufacturer's instructions for charging other brands of batteries. Batteries There are three methods of powering the GMRS862: 1. Alkaline Batteries. WARNING: Do not attempt to recharge Alkaline batteries. 2. Audiovox Rechargeable Ni-MH Batteries - (Rechargeable NiMH batteries and Charging Adapter). Use only Audiovox-approved rechargeable batteries and charging equipment when charging batteries internal to the unit. NOTE: To extend battery life, avoid overcharging the batteries. 7 128-7625 7 of 28 3. Various Brands of Rechargeable Batteries - Use of the Audiovox charger(s) with other brands of rechargeable batteries is not recommended, as battery charging times will vary with different brands of batteries. Refer to the manufacturer's instructions for charging other brands of batteries. Installing the batteries: Battery installation is made more convenient when the carry clip is either rotated left or right to the horizontal position, or is removed. Simply rotate the clip in either direction to the horizontal position. Be careful not to use excessive force. To remove the clip, press down on the release tab and pull the clip straight out from the radio body. Next, press down with the thumb at the embossed arrow, slide the battery cover down and lift it away from the compartment. Insert four AAA batteries (alternate positive ends (+) toward the top of the transceiver, starting left-to-right. CLIP RELEASE TAB CARRY CLIP COVER ARROW + + POSITIVE TERMINALS BATTERY COVER + + 8 128-7625 8 of 28 1. Using thumb, press down on battery cover at arrow and slide cover down. 2. Then lift cover at bottom to open. Remove cover. 3. Insert four AAA batteries (positive (+) end toward the top begining at left side and alternating positive terminals as shown). The following guidelines will improve performance and provide longer operating times for the GMRS862: 1. Do not mix old and new batteries. 2. The use of alkaline-type batteries is recommended to provide the longest operating time. 3. Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries. 4. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries can cause damage to the unit and will void the warranty. 9 128-7625 9 of 28 GMRS862 OPERATIONAL MODES GMRS/FRS (MODE) CHANNEL SELECT CTCSS SELECT POWER SELECT ROGER BEEP (1-22) (oF, 01-38) (GMRS channels only) (on or oF) NOTE: To differentiate between operating modes, look for HI or LO indication below the battery power level indicator when in GMRS mode.Refer to the appropriate section of this manual for detailed operating instructions for each mode. Channels 1 through 7 are shared GMRS/FRS. Channels 8 through 14 are FRS only, and channels 15 through 22 are GMRS only. Controls: Power On-Off/SCAN Button (13) Press and hold the PWR on/off button for at least 2 seconds. You will hear a confirming melody to indicate the unit is on. To turn the unit off, press and hold the button for at least 2 seconds. 10 128-7625 10 of 28 Adjusting the Volume (11, 10) With the unit powered on, press the Up Channel/Volume button ( ) to increase volume and the Down Channel/Volume button ( ) to decrease volume. The display will indicate the current volume level (UL) followed by the number (0-7). As volume is increased upward, the unit will beep at each step, and vice-versa. When the minimum and maximum volume settings are reached, a unique tone will sound. Monitor/Display Backlight Button (2) This button is used to to check activity on the current frequency before transmitting. Check activity by pressing the Monitor (M) Button longer than 2 seconds; the icon will apppear on the display and you will hear static if frequency is clear. Do not transmit if you hear conversation. Hold down the Monitor Button again longer than 2 seconds and the icon will disapppear from the display. The monitor function will temporarily bypass the squelch setting and play all signals on a given channel. This feature is useful when communicating with other parties at extreme range. By pressing the monitor button momentarily, the LCD backlight is turned on; the LCD backlight will turn off automatically in about 5 seconds, unless the monitor button is pressed momentarily once again. Push To Talk (PTT) Button (4) Pressing and holding this button will allow you to speak to any transceiver that is set to the same channel and privacy code setting as yours. Hold the transceiver approximately 1 to 2 inches from your face as you speak into the built in microphone (9). After you have finished speaking, release the PTT Button to allow reception of incoming signals. It is not possible to transmit and receive at the same time. Whenever the button is pressed, the transmit signal icon ( ) will appear in the upper left corner of the display. Releasing the button allows the unit to revert to standby mode. When receiving an incoming signal, the icon will appear. 11 128-7625 11 of 28 The PTT Button can also be used as a two-way call ringer. Pressing the button twice quickly will call another party on the same channel. The transmit ) will be displayed for 3 seconds and then disappear. icon ( Up Channel/Volume Button (10) In the standby mode, pressing this button will increment the listening volume. When in function edit mode this button will be used to adjust the unit's settings. Down Channel/Volume Button (11) In the standby mode, pressing this button will decrement the listening volume. When in function edit mode this button will be used to adjust the unit's settings. MODE/VOX Button (12) This button is used to select various feature settings in the GMRS and FRS modes. When pressed and held for 3 seconds, the VOX mode is entered and the VOX icon appears on the display. External Speaker (SPK)/ Microphone (MIC)/CHG Jack (6) This jack accepts both the supplied Audiovox boom microphone/headset connector and the wall charging adapter. For equipment and accessories for the GMRS862, refer to page 7 and/or visit the Audiovox web site at www.audiovox.com. Scan Button (13) With the unit in standby mode, press the Power On/Off Button momentarily to enable or disable the scan function; SCAN will appear on the display. 12 128-7625 12 of 28 Operating Modes and Features GRMS/FRS Operation: - Press and hold the Power On/Off button for 2 seconds to turn on power. - Press the MODE button so the Channel number flashes. - Select the desired channel with the Up (10) and Down (11) Buttons. When receiving a call, the icon appears to indicate an incoming call. - Press and hold the PTT button (4) to transmit, then speak into the microphone clearly and slowly. The Transmit icon ( ) appears on the display while the button is pressed. - Release PTT Button (4) to receive. - Communication can only be accomplished when the channel and CTCSS tone frequency of at least two parties are the same. - The CTCSS subcode (01-38) will be displayed on the LCD panel if the CTCSS tone frequency function is enabled (not oF). Channel Selection In order to communicate with other GMRS/FRS units, both the transmitting and receiving party must be on the same frequency. The GMRS862 has 22 channels (frequencies) indicated by the large digits on the LCD display panel. Channels 1 through 7 are the shared GMRS/ FRS channels. Channels 8-14 are FRS only channels, while channels 1522 are assigned GMRS only channels. ...