User manual AUDIOVOX VM9511TS

CONTENTS Thank you for choosing a Jensen product. We hope you will find the instructions in this owner's manual clear and easy to follow. If you take a few minutes to look through it, you'll learn how to use all the features of your new Jensen VM9511TS Mobile Multimedia AM/FM/DVD Receiver for maximum enjoyment. Preparation............................................................................................................................ 1 Installation ............................................................................................................................. 5 Controls and Indicators ......................................................................................................... 6 Front Zone Remote Control .................................................................................................. 9 Multi-ZONE Remote Control ............................................................................................... 12 Using the TFT Monitor ........................................................................................................ 13 Operating Instructions ......................................................................................................... 15 System Setup Menu............................................................................................................ 16 Multi-ZONE Operation......................................................................................................... 18 Tuner Operation .................................................................................................................. 19 XM Radio Operation............................................................................................................ 20 DVD/VCD Video Operation ................................................................................................. 22 DVD/Disc Setup Menu ........................................................................................................ 25 DVD/Disc Audio Operation.................................................................................................. 28 SD Card Reader Operation................................................................................................. 30 iPod Operation .................................................................................................................... 31 TV Tuner Operation ............................................................................................................ 32 Navigation System .............................................................................................................. 33 Troubleshooting .................................................................................................................. 34 Specifications ...................................................................................................................... 37 12-month Limited Warranty .................................................................................................37 TABLE DES MATIÈRES Merci d'avoir choisi un produit Jensen . Nous espérons que vous allez trouver les instructions dans ce guide de propriétaire claires et faciles à suivre . Prenez quelques minutes à le consulter, vous apprendrez à utiliser toutes les fonctions de votre nouvelle radio Jensen pour en tirer une jouissance maximum. Preparation......................................................................................................................... 77 Installation .......................................................................................................................... 81 Controles et indicateurs...................................................................................................... 82 Telecomande de la zone d'avant ....................................................................................... 85 Telecommande Multi-ZONE............................................................................................... 88 Utilisation du moniteur TFT ................................................................................................ 89 Instructions d'operation ...................................................................................................... 91 Menu configuration du systeme ......................................................................................... 93 Operation Multi-ZONE........................................................................................................ 95 Operation tuner AM/FM...................................................................................................... 96 Operation radio XM ............................................................................................................ 97 Operation platine DVD ....................................................................................................... 99 Menu de configuration DVD/disque.................................................................................. 102 Operation audio DVD/DisQUE ......................................................................................... 105 Operation lecteur carte SD............................................................................................... 107 Operation iPod ................................................................................................................. 108 Operation tuner TV........................................................................................................... 109 Systeme de navigation ..................................................................................................... 110 Depannage....................................................................................................................... 111 Specifications ................................................................................................................... 114 Garantie limitée de 12 mois .............................................................................................. 114 CONTENIDO Gracias por elegir los productos Jensen. Esperamos que encuentre en este manual instrucciones claras y fáciles de seguir. Si se toma unos pocos minutos para leerlo, aprenderá cómo utilizar todas las funciones de su nuevo radio Jensen para su máximo entretenimiento. Preparación......................................................................................................................... 39 Instalación ........................................................................................................................... 43 Controles e Indicadores ...................................................................................................... 44 Control Remoto de Zona Delantera .................................................................................... 47 Control Remoto de Multi-ZONE .......................................................................................... 50 Utilización del Monitor TFT ................................................................................................. 51 Instrucciones de Operación ................................................................................................ 53 Menú de Configuración de Sistema .................................................................................... 55 Operación Multi-ZONE........................................................................................................ 57 Operación del Radio ........................................................................................................... 58 Operación de Radio XM® .................................................................................................... 59 Operación del Video de DVD/VCD ..................................................................................... 61 Menú Configuración del DVD/Disc...................................................................................... 64 Operación del Audio de DVD/Disco .................................................................................... 67 Operación del Lector de Tarjeta SD.................................................................................... 69 Operación de iPod .............................................................................................................. 70 Operación del Sintonizador de TV ...................................................................................... 71 Sistema de Navegación ...................................................................................................... 72 Solución de Problemas ....................................................................................................... 73 Especificaciones ................................................................................................................. 76 Garantia Limitade de 12 Meses .......................................................................................... 76 i ii VM9511TS PREPARATION Congratulations on your purchase of the Jensen VM9511TS Mobile Multimedia AM/FM/DVD Receiver. It's a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9511TS installed by a reputable installation shop. XM Ready · Requires optional Terk XMD1000 tuner box · Requires optional Terk XMDJEN100 or Jensen JXMC XM cables · Advanced display shows the artist, song title, and XM channel and category at a glance · Direct channel entry Navigation Ready · Requires optional NAV100 navigation module jLink Ready · Controls and charges all iPod's except "Shuffle" · Displays all text information including category, track name, artist and channel number Chassis · 7-inch TFT touch screen LCD - 336,960 pixels (1440W X 234H) · TSD - Touch Screen Display menu control · Fully automatic motorized TFT LCD flip-out and up · 16-step TFT LCD tilt adjustment · Beep Tone confirmation · 1.0 Din · Import/ISO/DIN mountable · Heat management system - Incorporates forced aircooling to keep the chip-sets operating at nominal temperatures · Heavy duty galvanized chassis Multi-ZONE · Allows front passengers to listen to the radio while rear passengers listen to a CD, MP3, WMA or watch DVDs General · Full function infrared remote control · Limited function infrared "Kid Zone" remote · OSD - On Screen Display menu control · High-performance audio processor · Electronic volume, bass, treble, balance and fader · Bass center frequency adjustment - 60, 80, 100, 130, 150 and 200Hz · Bass Q factor - 1.0, 1.25, 1.5 and 2.0 · Treble center frequency adjustment - 10, 12.5, 15 and 17kHz · Subwoofer crossover - 80, 120 and 160Hz · Subwoofer Phase - 0 - 180 degrees · Subwoofer level - variable · 100-ohm low impedance pre-amp outputs, all channels · 5V Peak / 2V RMS RCA outputs, all channels · 1-pair front RCA outputs and 1-pair rear/surround RCA outputs · · · · · · · · · · Single Subwoofer RCA output Center Channel RCA pre-amp output (variable) 1-pair headphone/Multi-ZONE RCA outputs 1-pair auxiliary RCA A/V inputs Back-up camera input with reverse override 1 NTSC composite video output for additional screens NTSC Multi-ZONE composite video for additional screens Front panel (when screen is closed) high contrast LCD Rotary encoder audio control Joystick menu navigation Features DVD · Compatible formats: DVD-R, DVD-RW, DVD+R, DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD, VCD, MPEG2, MPEG4, AVI and JPEG · Region 1 playback · 16:9 Aspect ratio- Wide / Normal / Cinema · Front panel DVD control · High-speed Fast Forward / Fast Rewind 2X, 4X, 8X, 32X · Play, Pause, Stop, Slow · Chapter Up / Down · V-SEL - MultiZone output 'Kid-Zone' · Wolfson Microelectronics high performance 24-bit, 192 kHz DAC supports 6-channel and 2-channel "Down-Mix" audio modes · 16MB high-speed flash memory - 80nS access time · 2 second ESP (Electronic Skip Protection) Integrated SD Card Reader · Compatible formats: MP3, WMA, AVI, MPEG1, MPEG2, MPEG4 and JPEG · Supports up to 2GB SD card MP3/WMA · GIGA MP3 - Store up to 999 MP3 files on a DVD · ID3-tag compatible · Direct track access · Play, Pause, Stop, Track Up / Down · 60 second (MP3), 120 second (WMA) ESP - Electronic Skip Protection CD · CD-text compatible · 4 second ESP (Electronic Skip Protection) AM/FM Tuner · User-selectable frequency spacing · 30 Station presets (18FM/12AM) JENSEN Plus Tuner II Outboard Media Module · Input adapter for TV Tuner, XM and iPod TV Tuner (Included) · VHF 2-13 · UHF 14-69 · TV antenna (3.5mm antenna included) · F-Connector/Coaxial Antenna Input (optional) Tools and Supplies You will need these tools and supplies to install your VM9511TS: · · · · · · · · · Torx type, flat-head and Philips screwdrivers Wire cutters and strippers Tools to remove existing radio (screwdriver, socket wrench set or other tools) Electrical tape Crimping tool Volt meter/test light Crimp connections 18 gauge wire for power connections 16 ­ 18 gauge speaker wire WARNING! Only connect the unit to a12-volt power supply with proper grounding. WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions. WARNING! To reduce the risk of a traffic accident (except when using for rear-view video camera) never use the video display function while driving the vehicle. This is a violation of federal law. WARNING! Never disassemble or adjust the unit without the assistance of a professional. For details, please consult your local car stereo specialty shop. WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water. 1 VM9511TS WARNING! Never use irregular discs. WARNING! To prevent damage to the mechanism inside this unit, avoid impact to the TFT monitor. WARNING! Do not change the fuse on the power wire without professional guidance. Using an improper fuse may cause damage to the unit and result in a fire. WARNING! The monitor employs an automatic motorized mechanism. To prevent damage to the core mechanism, please do not push, pull or swivel the monitor manually. Optional Accessories iAUX3 READY (Sold Separately) · Can connect to any portable media device or multimedia device using a standard 3.5mm plug · Converts 3.5mm auxiliary input to RCA stereo outputs for easy connection to the radio's AUX inputs Disconnecting the Battery To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. NOTE: If the VM9511TS is to be installed in a vehicle equipped with an on-board drive or navigation computer, DO NOT disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit. 2 VM9511TS WIRING DIAGRAM 3 VM9511TS WIRING DIAGRAM - MULTIMEDIA CONNECTIONS *TERK XMDJEN100 cables (sold separately) **TERK XMD1000 Direct Tuner and antenna (sold separately) ***NAV100 (sold separately) 4 VM9511TS INSTALLATION Pre-installation 1. 2. Press the metal levers on both sides to remove the halfsleeve from the radio. Remove the transport screws. PREPARE RADIO CAUTION! Be careful not to damage the car wiring. 4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. FINAL INSTALLATION Wiring Complete wiring as illustrated in the wiring diagram on page 3. Once the wiring is complete, reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch. NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The VM9511TS uses one 15 amp mini-ATM fuse, located in the black filter box in-line with the main wire harness. Final Installation After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis. 1. 2. 3. Connect wiring adapter to existing wiring harness. Connect antenna lead. Carefully slide the radio into the half-sleeve, making sure it is right-side-up, until it is fully seated and the spring clips lock it into place. Final ISO-DIN Installation 1. 2. 3. 4. Remove trim ring. Mount factory brackets on new radio using existing screws from old radio. Slide radio chassis into dash opening and secure. Reinstall dash panel. FINAL ISO-DIN INSTALLATION 3. Install the half-sleeve. a. Install adapter if necessary (optional). b. Install half-sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow. c. Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard. d. Install support strap to make the unit more stable. INSTALL HALF SLEEVE NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 20° of horizontal. Make sure the unit is mounted within this limitation. 4. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary. 3d 3c Using the iAUX3 External AV Connector The iAUX3 (sold separately) allows you to connect a variety of external devices, including a VCR, DVD player, portable MP3 player, etc., to your VM9511TS without removing the radio. To install the iAUX3, connect it to the AUX-IN cables on the back of the VM9511TS (see the Wiring Diagram on page 3), and then install the iAUX3 in a location convenient for plugging in auxiliary devices. 3a CAUTION! The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration. 5. Replace any items you removed from the dashboard. 3b 5 VM9511TS CONTROLS AND INDICATORS Button Operation 1. OPEN Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. WIDE/ PICTURE Press to adjust the display aspect of the picture to one of three settings: Cinema, Full, Normal or OFF. Press and hold to access picture settings. 3. ( ) Press to adjust the upward tilt angle of the screen one step at a time. Press and hold this button to continuously adjust the upward tilt or picture settings. 4. ( ) Press to adjust the downward tilt angle of the screen one step at a time. Press and hold this button to continuously adjust the downward tilt or picture settings. 5. DISP Press to display system information on the screen. 6. VOL/LO/DX Rotate to adjust the volume. Press and release to enter and/ or confirm audio settings. Press and hold to activate the Local (LOC) setting. 7. POWER/MUTE Press once to turn the unit on. Press again to mute the volume. Press and hold to turn the unit off. 8. 1/AUDIO DVD Mode: Press to select audio language during playback. TUNER Mode: Press once to play preset radio station channel 1. Press and hold to store the current radio station in preset channel 1. 9. 2/SUBTITLE DVD Mode: Press once to select the subtitle language during playback. TUNER Mode: Press once to play preset radio station channel 2. Press and hold to store the current radio station in preset channel 2. 6 VM9511TS CONTROLS AND INDICATORS 10. 3/SCN DVD Mode: Press once to start scan playback. TUNER Mode: Press once to play preset radio station channel 3. Press and hold to store the current radio station in preset channel 3. 11. 4/RPT DVD Mode: Press once to start repeat playback. TUNER Mode: Press once to play preset radio station channel 4. Press and hold to store the current radio station in preset channel 4. 12. 5/2-6CH/RDM DVD Mode: Press once for random playback. TUNER Mode: Press once to play preset radio station channel 5. Press and hold to store the current radio station in preset channel 5. CD Mode: Press and hold to switch between 2 channel & 6 channel audio output. 13. 6/STOP DVD Mode: Press once to stop playback. TUNER Mode: Press once to play the preset radio station channel 6. Press and hold to store the current radio station in preset channel 6. 14. BAND TUNER Mode: Press to switch between FM and AM. 15. SRC Press once to select playing mode. Press and hold to toggle rear zone mode On/0ff. 16. ( ) DVD Mode: Press once to play back the previous chapter/ track. TUNER Mode: Press once to auto-search for the previous available radio station. MENU Mode: Press once to move the cursor to the left. 17. ( ) DVD Mode: Press once to enter the next chapter or track. TUNER Mode: Press once to auto-search the next available radio station. MENU Mode: Press once to move the cursor to the right. 18. ( ) DVD Mode: Press once for fast forward/fast reverse. TUNER Mode: Press to go up one frequency step. MENU Mode: Press once to move the cursor up. 19. ( ) DVD Mode: Press once for slow forward/slow reverse. TUNER Mode: Press to go down one frequency step. MENU Mode: Press once to move the cursor down. 20. PLAY/ENTER DVD Mode: Press once to start a playback. Press once to confirm a selection. 21. ( ) Press once for disc insertion/ejection. Press and hold to reset core mechanism position. 22. RESET Press to reset system settings to factory default (except the password and parental lock setting). 23. LCD Display 24. TFT Display 25. IR Remote Control Receiver 26. AS (Auto Store) Press to automatically store strong radio stations in the six preset channels in the current band. 27. SD Card Slot 7 VM9511TS CONTROLS AND INDICATORS LCD Display/Indicators 1. Disc Indicator Illuminated when disc is loaded 2. DVD Playback Indicators (SCN/RPT/RDM/ALL) The following DVD playback indicators become Illuminated when the corresponding function is active: · · · · SCN: scan playback RPT: repeat playback RDM: random playback ALL: playback all chapters 1 2 3 4 5 6 3. Loudness Indicator (LOUD) The loudness indicator becomes illuminated when the LOUD function is activated. 4. Main Display The main display is an 8 digit, 14 segment LCD which displays the time, tuning frequency and other text information. 5. Channel/Disc Display The channel/disc display is a 2 digit, 7 segment LCD display which displays the disc number or radio channel indicators when the corresponding function is active: · · CH: radio is activated DISC: DVD mode is activated 6. Stereo/Local Indicator The stereo/local indicator illuminates one of the following indicators when the corresponding function is active: · · ST: radio is in stereo mode LOC: local radio station seeking function is activated 8 VM9511TS FRONT ZONE REMOTE CONTROL NOTE: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only. 9 VM9511TS Table 1: Front Zone Remote Control Functions Button Name MENU TITLE MUTE POWER/ AUDIO REPT A-B Function Ref# 1 2 3 4 5 6 DVD Enters the main menu of the disc Enters the title menu of the disc Toggles on/off audio output Turns the power on/off Changes the audio language for disc playback Setup to repeat playback from time frame A to time frame B Repeats playback of current chapter Selects playing mode Language selection for subtitle Displays playing information Continuously adjusts front panel tilt angle Continuously adjusts front panel tilt angle Plays back disc in different angle for a scene Fast forwards the disc content Decreases volume Increases volume Selects the previous chapter for playback Pauses playback/starts playback VCD Turns on PBC when playing VCD Plays first ten seconds of each chapter/title Toggles on/off audio output Turns the power on/off TUNER CD/MP3 TV XM Displays XM Setup Menu iPod Selects Photo mode Selects Music mode Toggles on/off audio output Turns the power on/off Toggles on/off audio output Turns the power on/off Toggles on/off audio output Turns the power on/off Toggles on/off audio output Turns the power on/off Toggles on/off audio output Turns the power on/off Selects Video mode Setup to repeat playback from time frame A to time frame B Repeats playback of current chapter Selects playing mode Selects playing mode Repeats playback of current track Selects playing mode Selects playing mode Selects Category Mode Selects playing mode Repeats playback of current track Selects playing mode REPT SRC SUBTITLE INFO ANGLE ANGLE ANGLE 7 8 9 10 11 12 13 Displays playing information Continuously adjusts front panel tilt angle Continuously adjusts front panel tilt angle Plays back Picture CD with different angle of picture displayed Fast forwards the disc content Decreases volume Increases volume Selects the previous chapter for playback Pauses playback/starts playback Displays playing information Continuously adjusts front panel tilt angle Continuously adjusts front panel tilt angle Display playing information Continuously adjusts front panel tilt angle Continuously adjusts front panel tilt angle Displays playing information Continuously adjusts angle of TFT screen Continuously adjusts angle of TFT screen Displays playing information Continuously adjusts angle of TFT screen Continuously adjusts angle of TFT screen Displays playing information Continuously adjusts angle of TFT screen Continuously adjusts angle of TFT screen 14 VOL VOL + 15 16 17 Fast forwards the disc content Decreases volume Increases volume Searches an available radio station by decreasing tuning frequency Scans FM/AM radio station; plays/stores radio station; deletes radio station Searches an available radio station by increasing tuning frequency Selects FM/AM band Decreases volume Increases volume Selects the previous track for playback Pauses playback/starts playback Decreases volume Increases volume Searches an available TV station by decreasing tuning frequency Scans TV station; plays/ stores TV station; deletes TV station Searches an available TV station by increasing tuning frequency Decreases volume Increases volume Searches an available radio station by decreasing tuning frequency Scans XM radio station; plays/stores radio station; deletes radio station Searches an available radio station by increasing tuning frequency Selects XM, XM1, XM2, or XM3 band Accesses iPod Menu Decreases volume Increases volume Pauses playback/starts playback 18 19 Selects the next chapter for playback Stops playback Selects the next chapter for playback Stops playback Selects the next track for playback Stops playback Selects the next track for playback BAND 20 10 VM9511TS Table 1: Front Zone Remote Control Functions Button Name GOTO Function Ref# 21 22 DVD Goes to specific time frame and playback Slow playback/slow rewind playback Zooms in/out on an image Displays set-up parameters Opens/closes the TFT monitor Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: CINEMA, WIDE, NORMAL or Off (Standby) Directly accesses chapter VCD Goes to specific time frame and playback Slow playback/slow rewind playback Zooms in/out on an image Displays set-up parameters Opens/closes the TFT monitor Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: CINEMA, WIDE, NORMAL or Off (Standby) TUNER CD/MP3 TV XM iPod ZOOM PIC OPEN/ CLOSE 23 24 25 26 27 Opens/closes the TFT monitor Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: CINEMA, WIDE, NORMAL or Off (Standby) 1-6 selects preset for current band Opens/closes the TFT monitor Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: CINEMA, WIDE, NORMAL or Off (Standby) Directly accesses track Opens/closes the TFT monitor Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: WIDE or OFF 1-6 selects preset TV stations Opens/closes the TFT monitor Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: WIDE or OFF 1-6 selects preset for current band Opens/Closes the TFT monitor Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: WIDE or OFF DISP 28 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (Numeric Keypad) DVD SETUP SYS SETUP SEL RDM SCN EJECT 29 30 31 32 33 34 35 Displays DVD Setup menu Displays System Setup menu Displays DVD Setup menu Displays System Setup menu Displays DVD Setup menu Displays System Setup menu Displays DVD Setup menu Displays System Setup menu Displays DVD Setup menu Displays System Setup menu Displays DVD Setup menu Displays System Setup menu Displays DVD Setup menu Displays System Setup menu Plays all chapters in random order Plays all tracks in random order Plays the first ten seconds of each track Plays all tracks in random order Ejects disc Ejects disc Ejects disc Ejects disc Ejects disc Ejects disc Ejects disc 11 VM9511TS MULTI-ZONE REMOTE CONTROL Table 2: Multi-Zone Remote Control Functions Button Name MENU TITLE MUTE AUDIO REPT R.SRC SUBTITLE 1 2 3 5 7 8 9 14 17 18 19 GOTO 21 22 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (Numeric Keypad) 29 Function Ref # DVD Enters the main menu of the disc Enters the title menu of the disc Toggles on/off audio output Switches the audio language for disc playback Setup to repeat playback of each chapter/title/disc Selects playing mode for rear zone Language selection for subtitle Fast forwards the disc content Selects the previous track/chapter for playback Pauses playback/Starts playback Selects the next track/chapter for playback Goes to specific time frame and playback Slow playback/slow rewind playback Directly accesses chapter Fast forwards the disc content Selects the previous track/chapter for playback Pauses playback/Starts playback Selects the next track/chapter for playback Goes to specific time frame and playback Slow playback/slow rewind playback Setup to repeat playback of each chapter/title/disc Selects playing mode for rear zone VCD Turns on PBC when playing VCD Plays first ten seconds of each chapter/title Toggles on/off audio output NOTE: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only. 12 VM9511TS USING THE TFT MONITOR Open/Close TFT Monitor Open TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (25) of the front zone remote control to activate the mechanism that moves the display panel into the viewing position. Close TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (25) of the front zone remote control to load the display panel back into the compartment. Aspect Ratio Press the DISP button (28) on the remote control or WIDE/ PICTURE button (2) on the monitor to adjust the aspect ratio as follows: CINEMA The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. WIDE The screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio increases toward the right and left ends of the screen. NORMAL The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display. OFF "COLOR", "CONTRAST", and "TINT" you must be in AUX, CAMERA or TV Tuner mode. NOTE: The default adjustment is "0" in PAL mode. Tint is unavailable for adjustment. Parameter Adjustment Procedure 1. Enter Picture Quality Setting mode: Press the PIC button (24) on the remote or press and hold the WIDE/PICTURE button (2) on the monitor panel. 2. Select Item to Set: Press the (>>) (<<) buttons (14, 22) on the remote or press and hold the (/\) or (V) buttons (18, 19) on the monitor panel. 3. Set Parameters: Press (|<<) (>>|) buttons (17, 19) on the remote or press (<) (>) buttons (16, 17) on the monitor panel. 4. Exit Picture Quality Setting Mode: Press the PIC button (24) on the remote or press and hold the WIDE/PICTURE button (2) on the monitor panel. TFT Monitor Auto Open If "TFT Auto Open" is "on" when the unit is turned on, the monitor automatically moves to the viewing position. If "TFT Auto Open" is "off" when the unit is turned on, press the OPEN button (1) or ( ) button (25) on the front zone remote control to move the monitor into the viewing position. If "TFT Auto Open" is set to "Manual", the TFT will not close when the key is turned off. Reverse Driving Use If the rear-view video camera is connected, the unit is on, and the monitor is stationed inside the main compartment of the unit, the monitor automatically moves into the viewing position and switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor returns to the main storage compartment. If the monitor is in display mode, the monitor automatically switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor return to its original input mode. Parking Brake Parking Brake Inhibit When the pink "Parking" wire is connected to the vehicle brake switch, the front TFT monitor will display video only when the parking brake sequence is engaged. Before starting the parking brake sequence, the radio must be on with the video media disc inserted and playing. Parking Brake Sequence There are two situations that can start the Parking Brake Sequence: · Parking brake is engaged (on) when the vehicle is started or the accessory/ignition is turned on. To activate video, the following sequence of events must be completed: a. Release parking brake for 2 seconds. b. Reapply the parking brake for 2 seconds. c. Video should be displayed on the TFT monitor within 1 ~ 2 seconds. Parking break is disengaged (off) when the vehicle is started or the accessory/ignition is turned on. To activate video, the following sequence of events must be completed: a. Set parking brake for 2 seconds. b. Release parking brake for 2 seconds. c. Reapply parking brake. Image Setting Table 3 shows the video output mode for each playing source. Table 3: Video Output Modes Playing Source AM/FM TUNER XM TUNER iPod DVD NAV TV AUX IN CAMERA Monitor Tilt Angle Adjustment A known characteristic of LCD panels is the quality of the display in relationship to the viewing angle. The monitor angle can be adjusted for optimum viewing using one of the following methods: Step by Step Angle Adjustment Press the ( ) or ( ) button (3, 4) on the monitor frame to adjust the tilt angle of the screen one step at a time. Continuous Angle Adjustment Press and hold the ( ) or ( ) button (3, 4) on the monitor frame to adjust the tilt angle in a continuous motion. Video Output Modes RGB Mode RGB Mode RGB Mode RGB Mode RGB Mode CVBS Mode CVBS Mode CVBS Mode · *CVBS ­ Composite Video Baseband Signal Adjustable Parameters While in DVD or TUNER mode, the only parameter that can be adjusted is brightness (BRIGHT). To access "PICTURE", 13 VM9511TS d. Video should be displayed on the TFT monitor within 1 ~ 2 seconds. Monitor Movement Mechanism If an obstruction occurs in the monitor path, the following protective measurements can be executed to prevent damage to the mechanism or monitor: Table 4: Monitor Protective Measures Obstruction Monitor loading out horizontally Monitor loading in horizontally Monitor loading out vertically Monitor loading in vertically Self Protection Monitor is automatically loaded into unit Unit stops at obstruction point Unit stops at obstruction point Unit stops at obstruction point OPEN Button Pressed Monitor fully extended horizontally Monitor fully extended horizontally Monitor swivels back to the unit Monitor swivels back to the unit Power Reconnected Monitor is automatically loaded into unit Monitor is automatically loaded into unit Monitor swivels back to the unit Monitor swivels back to the unit After the protective procedure is executed, normal operation is resumed by pressing the OPEN button (1) or disconnecting and reconnecting the power. 14 VM9511TS OPERATING INSTRUCTIONS Power On / Off Press the /MUTE button (7) to turn the unit on. The buttons on the front of the unit light up and "WELCOME" appears briefly in the LCD panel (23), followed by the current mode status. If the TFT screen is open, only the current mode status is displayed. You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the /MUTE button (7) on the front panel or the POWER button (4) on the remote to power off the unit.The monitor is drawn back into the main compartment and the LCD screen displays "BYE BYE". To program a specific volume level, push and hold the VOL/ LO/DX knob (6) while the yellow volume bar is displayed on the screen. The unit will beep two times to confirm your turnon volume setting. The Loud function compensates for deficiencies in sound ranges at low levels. Loudness levels range from 1-4 or "off". When the Loud function is on, "LOUD" is displayed on the screen. Exiting the Audio Control Menu Press and hold the VOL/LO/DX knob (6) or stop making adjustments for a few seconds to exit the audio control menu. Audio Control Menu The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. To get the best possible sound quality from your new system, be sure to adjust the settings for the speakers as well. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer. Accessing the Audio Control Menu Press the VOL/LO/DX knob (6) on the front panel once to display the "AUDIO" menu. Selecting an Audio Feature for Adjustment Continuously press the VOL/LO/DX knob (6) on the front panel, or press the (>>)/(<<) buttons (14, 22) on the remote control or the (/\)/ (V) buttons (18, 19) on the joystick to select the audio feature to be adjusted. Adjusting an Audio Feature Rotate the VOL/LO/DX knob (6), press the (|<<)/(>>|) buttons (17, 19) on the remote control, or press the (<)/(>) buttons (16, 17) on the joystick to adjust the selected feature to the desired setting. Table 5: Audio Adjustments Audio Function EQ User Flat Jazz Pop Classical Rock Vocal BASS TREBL SUB LOUD FAD (Fade) BAL -14 to +14 -14 to +14 -7 to +7 0 (off), 1-4 -9 to +9 -9 to +9 Six-Channel Audio Control NOTE: Before adjusting the volume of any speaker, please refer to "Surround Sound" on page 26. Audible Beep Confirmation An audible beep tone confirms each function selection. The beep tone cannot be disabled. Table 6: 6-Channel Audio Adjustments Item Master Volume Front Left Channel Volume Front Right Channel Volume Rear Left Channel Volume Rear Right Channel Volume Center Channel Volume Subwoofer Volume Adjustable Range 00 to 40 -10 to +10 -10 to +10 -10 to +10 -10 to +10 -10 to +10 -10 to +10 Mute Press the /MUTE button (7) on the front panel or the MUTE button (3) on the remote to mute the volume from the unit. Press the MUTE button again to restore the volume. "MUTE" is displayed on the LCD monitor. Adjusting the volume or using any of the audio setup features cancels the mute function. Playing Source Selection Press the SRC button (15) on the front panel or the SRC button (8) on the remote to change between available playing sources in the following order: TUNER, DVD, CD Changer, AUX IN, CAMERA (rear view video camera) and SD. The playing mode is displayed on the TFT and LCD screens. AUX IN Mode An external peripheral device can be connected to this unit via RCA output and "AUX-IN". CAMERA Mode "CAMERA" mode is only available if the camera is connected and during reverse driving. To install a rear view video camera, connect the video input cable to the camera output cable. Rear Zone If a monitor is installed in the rear zone and connected to the rear zone AV output, passengers in the back seat can control the DVD output using the rear zone remote control. See "Multi-Zone Remote Control" on page 12 for instructions. Adjustable Range System Reset To correct a system halt or other illegal [RESET] Button operation, use the tip of a pen to press the RESET button (22) located on the front bottom-right corner of the unit. After a system reset, the unit restores all factory default settings. NOTE: If the unit is reset while a DVD is playing, the DVD resumes play once the reset is complete. Volume Adjustment To increase or decrease the volume level, turn the ROTARY ENCODER (6) on the front panel or press the VOL+/ VOL- buttons (15, 16) on remote control. When the volume level reaches "0" or "40", a beep sounds, indicating that the adjustment limit has been reached. The volume ranges from "0" to "40". The LCD or TFT screen displays the volume level for 3 seconds. Programmable Turn-On Volume This feature allows the user to select a turn-on volume setting regardless of the volume setting prior to turning the unit off. Line Mute If the "MUTE" wire is connected, audio output mutes when a telephone call is received by the car phone or when verbal navigation is performed. NOTE: The Bass and Treble levels are only adjustable when EQ is set to "User" mode. 15 VM9511TS SYSTEM SETUP MENU In "System Setup" mode, "ASP CONFIG" and "GENERAL SETUP" are available for adjustment. Setup can be performed by pressing the dedicated button on the remote control or by touching the top left corner of the TFT screen. For system settings, press the SYS SETUP button (31) on the remote control or touch "SETUP" on the screen to enter the "SETUP" menu. "SYS SETUP" is highlighted in green. Adjusting a Feature 1. Enter the option field for the feature you want to adjust by pressing the >/|| button (18) on the remote or by pressing the ENTER (joystick) button (20) on the unit. A submenu appears in a second row with the selected option highlighted in light blue. 2. Select a new value by pressing the >> or << buttons (14, 22) on the remote control or the /\ or V buttons (18, 19) on the joystick. 3. Confirm your selection by pressing the <<, |<<, or >>| buttons (14, 17, 19) on the remote control, or the < or > button (16, 17) on the joystick. The new value is highlighted in light blue and setup is complete. Table 7: General Setup Menu Features DIRECTION BUTTONS Setting Radio Table 7: General Setup Menu Features Setting Options China Function · AM Frequency Spacing - 9kHz · AM Frequency Band 522kHz~1620kHz · FM Frequency Spacing - 100kHz · FM Frequency Band 87.5MHz~108.0MHz Clock displays 12 hour time using AM and PM. Clock displays 24 hour time up to 23:59. Turn screen saver on/off. General Setup Menu Accessing the General Setup Menu To access the "GENERAL SETUP" Menu, press the direction buttons on the joystick (16, 17, 18, 19) or remote control (14, 17, 18, 19, 22) to highlight "GENERAL SETUP" in green. Clock Mode 12H 24H Screen Saver On Off Options USA Function · AM Frequency Spacing - 10kHz · AM Frequency Band 530kHz~1720kHz · FM Frequency Spacing - 200kHz · FM Frequency Band 87.5MHz~107.9MHz · AM Frequency Spacing - 9kHz · AM Frequency Band 522kHz~1620kHz · FM Frequency Spacing - 50kHz · FM Frequency Band 87.5MHz~108.0MHz · AM Frequency Spacing - 10kHz · AM Frequency Band 530kHz~1720kHz · FM Frequency Spacing - 100kHz · FM Frequency Band 87.5MHz~108.0MHz · AM Frequency Spacing - 5kHz · AM Frequency Band 520kHz~1600kHz · FM Frequency Spacing - 100kHz · FM Frequency Band 87.5MHz~108.0MHz · AM Frequency Spacing - 9kHz · AM Frequency Band 531kHz~1620kHz · FM Frequency Spacing - 100kHz · FM Frequency Band 87.5MHz~108.0MHz · AM Frequency Spacing - 9kHz · AM Frequency Band 531kHz~1602kHz · FM Frequency Spacing - 200kHz · FM Frequency Band 88.1MHz~107.9MHz Europe Video Format (Input circuitry autodetects the video signal from the CAMERA and Aux In video source. Video format does not affect the TV tuner - this is an NTSC TV tuner only. TFT Auto Open Auto The color signal output is switched automatically based on the current video input signal - NTSC or PAL. The color signals are output in the standard NTSC format. The color signals are output in the standard PAL format. NTSC PAL Press the >/|| button (18) on the remote control to enter the "GENERAL SETUP" menu. A menu appears with the option for the first item, "Radio", highlighted in light blue. On Off Manual South America 1 The TFT panel automatically opens when the unit is turned on. You must press the OPEN button (1) to open the TFT panel. When the ignition is turned OFF, the TFT panel DOES NOT retract if it was previously out The menus are displayed in English only. See "Adjusting the clock" to learn how to set the clock. Return to previous menu. South America 2 OSD Language Clock BACK English (HH:MM) Arabia Korea Selecting a Feature for Adjustment Press the >> or << buttons (14, 22) on the remote control or the /\ or V buttons (18, 19) on the joystick to select the feature to be adjusted. Adjusting the Clock 1. Access the "Clock" setting under the General Setup menu. 2. Press the >> or << buttons (14, 22) on the remote control or the /\ or V buttons (18, 19) on the joystick to move the cursor to the "Hour" or "Min" position. 3. Press the |<< or >>| buttons (17, 19) on the remote control or the < or > buttons (16, 17) on the joystick to adjust the hour or minutes. 4. Press the << button (14) on the remote control to confirm setup. 16 VM9511TS Returning to the System Setup Menu To return to the System Setup menu, move to "BACK", then press the >/|| button (18) on the remote control. button (16, 17) on the joystick. The new value is highlighted in light blue and setup is complete. Table 8: ASP Config Menu Features Setting Bass Center Freq ASP (Audio Sound Processing) Config Menu The ASP Config Menu allows you to make fine audio adjustments. Accessing the ASP Config Menu To access the "ASP CONFIG" Menu from the "SYSTEM SETUP" menu, press the direction buttons on the joystick (16, 17, 18, 19) or remote control (14, 17, 18, 19, 22) to highlight "ASP CONFIG" in green. Press the >/|| button (18) on the remote control to enter the "ASP CONFIG" menu. A menu appears with the option for the first item, "Bass Center Freq", highlighted in light blue. Options 60Hz 80Hz 100Hz 130Hz 150Hz 200Hz Function According to the audio source, select the Bass Center Frequency to achieve the best Bass effect. Treble Center Freq 10KHz 12.5KHz 15KHz 17KHz According to the audio source, select the Treble Center Frequency to achieve the best Treble effect. Sub.W Filter 80Hz 120Hz 160Hz Selecting a crossover frequency sets a cut-off frequency of the subwoofer's LPF (low-pass filter) and the "SMALL" speakers' HPF (high-pass filter). The Crossover frequency setting has no effect if the subwoofer is set to "OFF" and any other speaker is set to "LARGE". Subwoofer output IN phase Subwoofer output OUT OF phase NOTE: Depending on your installation, reversing the subwoofer phase may increase Bass output. Sub.W Phase 0D 180D Bass Q-Factor 1.0 1.25 1.5 When the Bass Center Frequency is selected, adjusting the Bass Q-Factor alters the sharpness of the Bass output. Adjusting a Feature 1. Enter the option field for the feature you want to adjust by pressing the >/|| button (18) on the remote or by pressing the ENTER (joystick) button (20) on the unit. A submenu appears in a second row with the selected option highlighted in light blue. 2. Select a new value by pressing the >> or << buttons (14, 22) on the remote control or the /\ or V buttons (18, 19) on the joystick. 3. Confirm your selection by pressing the <<, |<<, or >>| buttons (22, 17, 19) on the remote control, or the < or > 2.0 BACK Return to previous menu. Screen Calibration After entering calibration mode, a crosshair appears in a corner quadrant of the screen. To begin calibration, press and hold the crosshair for one second until it moves to the next quadrant. Continue for each quadrant until the calibration is completed. Exiting the System Setup Menu To exit setup mode and resume normal playback, press the SYS SETUP button (31) on the remote control or the DISP button (5) on the front panel. 17 VM9511TS MULTI-ZONE OPERATION Independent sources can be played simultaneously on the VM9511TS. For example, a video game console can be seen on the front screen while DVD video is available to rear passengers. NOTE: If DVD is selected as the front source and SD Card is selected for the rear source, then both sources will switch to SD Card. If SD Card is selected as the front source and DVD is selected for the rear source, then both sources will switch to the DVD source. Since the multimedia processor is shared between optical and SD Card media, one or the other can be selected, but not both simultaneously. Selecting a Source for the Front Zone To access the FRONT ZONE SOURCE MENU, touch the TFT screen in the top left corner of the screen. Table 9: Multi-ZONE Source Options Front Zone Source TV Aux In Nav Available Multi-ZONE Sources DVD/CD, Aux In, TV, Nav DVD/CD, TV, Aux In, Nav DVD/CD, SD Card, Aux In, Nav Voice Prompt To access the rear zone SOURCE MENU, touch the top right corner of the screen, near the Multi-ZONE icon. Select the source to be directed to the rear Multi-ZONE RCA outputs. NOTE: Optical media and an SD Card cannot be selected from the Multi-ZONE Source Menu simultaneously. This menu allows you to select a source for the front zone. Selecting a Source for the Rear Zone The Multi-ZONE sources available for selection depends upon which Front Zone source is selected, as indicated in Table 9. Table 9: Multi-ZONE Source Options Front Zone Source AM/FM Tuner DVD/CD SD Card iPod XM NOTE: The AM/FM tuner graphics will change to a "blue screen" background when any optical or SD Card media is selected from the Multi-ZONE menu. In addition, only the top left (Front Zone Source Menu) and right (MultiZONE Source Menu) quadrants of the touch screen are active during this mode of operation. Available Multi-ZONE Sources DVD/CD, SD Card, TV, Aux In, Nav DVD/CD, TV, Aux In, Nav DVD/CD, TV, Aux In, Nav Aux In, Nav Voice Prompt Aux In, Nav Voice Prompt 18 VM9511TS TUNER OPERATION Tuner TFT Display Default TFT Tuner Display Alternate TFT Tuner Display The VM9511TS offers an alternate display for the AM / FM tuner interface that is less bright than the default tuner display and is more appropriate for night driving. Using Preset Stations Six numbered preset buttons store and recall stations for each band. All six stored stations (P1-P6) for the current band appear on the screen. Storing a Station 1. Select a band (if needed), then select a station. 2. Touch and hold an on-screen preset button (6) for three seconds. The preset number appears at the top of the screen. Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button (6) to select the corresponding stored station. To activate this feature, open the TFT screen and then press and hold the DISP button (5) for more than one second. To deactivate, press and hold the DISP button again. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Current Radio Band Indicator Radio Frequency Indicator Clock Stereo Broadcasting Indicator Strong Local Signal Broadcasting Indicator: Touch and hold to activate/deactivate Local function Preset Radio Stations: Touch to recall preset stations or touch and hold to store a station Front Zone Playing Mode Rear Zone Playing Mode User Defined Equalizer Level Loud Setting Indicator Current Preset Station Indicator |<<: Touch to seek backward >>|: Touch to seek forward <<: Touch to tune backward one step >>: Touch to tune forward one step BAND: Touch to change between AM/FM bands AS: Touch to automatically store stations Touch this area to return to the MAIN MENU Auto Store (AS) Automatic Storing of Preset Stations To select six strong stations and store them in the current band: 1. 2. Select a band (if needed). Touch AS (26) for 2 seconds to activate the Auto Store function. Switch to Radio Tuner source Press the SRC button (15) on the front panel or remote control (8) to switch to the TUNER source. Select FM/AM Band Touch the BAND button (16) on the screen, or press the BAND button on the unit (14) or remote control (20) to change between the following bands: FM1, FM2, FM3, AM1, and AM2. The new stations replace stations already stored in that band. Local Radio Station Seeking (LOC) When the Local function is on, only radio stations with a strong radio signal are played. To activate the Local function in AM/FM tuner mode, press and hold the VOL/LO/DX knob (6) on the front panel while the yellow volume bar IS NOT visible. Press VOL/LO/DX again to turn Local off. When the Local function is active, "LOC" appears on the screen and a green indicator is illuminated. Auto Tuning Press and hold the >>| button (19) on remote control or screen, or the > button on the joystick (17) to seek the next available radio station by increasing the tuning frequency. Press the button again to stop searching. Press and hold the |<< button (17) on the remote control or screen, or the < button on the joystick (16) to seek the next available radio station by decreasing the tuning frequency. Press the button again to stop searching. Manual Tuning Press the >> or << buttons (14, 22) on the remote control or screen, or the /\ or V buttons (18, 19) on the joystick to increase or decrease the tuning frequency one step. Press and hold the buttons to continuously tune until you release them. 19 VM9511TS XM RADIO OPERATION Listeners can subscribe to XM® Radio on the Web by visiting www.xmradio.com, or by calling (800) 967-2346. Customers should have their Radio ID ready (see "Displaying the Identification (ID) Code"). Customers can receive a limited number of free-to-air channels without activation. 17. MENU: Access the XM Setup Menu 18. Touch this area to return to the MAIN MENU Channel Guide, press the SUBTITLE button (9) on the remote control. Channel Guide Mode When Channel Guide mode is selected, "Search Mode" and "CHANNEL" appear in the top half of the user interface. "XM" appears in the top right corner and the first six XM channels are displayed in the boxes in the bottom half of the TFT screen. Displaying the Identification (ID) Code Before you listen to XM® Radio, you must subscribe to the service using your radio's identification number. To display the radio ID, press the < or > buttons (16, 17) on the joystick or the CH << or CH >> buttons on the touch screen repeatedly to tune to channel "000". The screen displays the 8-character XM radio ID under "CHANNEL NAME". Accessing XM® Radio Mode Press the SRC button (15) on the front panel or remote control (8) to switch to the XM source. Selecting a Station Press the < or > buttons (16, 17) on the joystick, the |<< or >>| buttons (17, 19) on remote control, or the CH << or CH >> buttons on the touch screen to change to another station. Preset Mode To enter preset mode, touch the BAND button on the screen, or press the BAND button on the unit (14) or remote control (20) to change between the following bands: XM1, XM2, or XM3 (indicated in the top right corner of the TFT screen). Six numbered preset buttons store and recall stations for each band. All six stored stations (P1-P6) for the current band appear on the TFT screen. Storing a Station 1. Select a band (if needed), then select a station. 2. Touch and hold an on-screen preset button for three seconds. The preset number appears at the top of the screen. XM channel name XM channel number XM band Time Song title Artist name Song category Data services information Current preset channels/on-screen preset buttons CH <<: Select the previous channel CH >>: Slect the next channel CAT /\: Select next channel in current category only CAT V: Select previous channel in current category only DIR CH: Press to enter channel directly using keypad on screen 15. XM CG: Access Channel/Category Guide mode 16. BAND: Change between XM, XM1, XM2 and XM3 bands 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button to select the corresponding stored station. · While in Search Mode, to switch between Channel and Category search modes, press the CH or CAT buttons in the touch screen. Press the >> button (14) on the remote control, the /\ button (18) on the joystick, or the > button on the touch screen to view the next page of stations. Each page contains six channels to select from. Press the << button (22) on remote control, the V button (19) on the joystick, or the < button on the touch screen to view the previous page of stations. Each page contains six channels to select from. Press the on-screen SCAN button to preview each of the 6 channels on screen for 10 seconds. Press the on-screen button to return to the Preset Mode screen. Press the on-screen MENU button to access the XM Setup Menu. · · · · Channel/Category Guide Mode There are two search modes to help navigate through channels and or categories. To access the Channel/Category Guide mode press, the ZOOM button (23) on the remote control or the XM CG button on the touch screen. Channel Guide is the default search mode. To access Category Guide, press the TITLE button (2) on the remote control or touch CAT on the touch screen. To return to · To select a channel while in Channel Guide mode, press the corresponding preset number (1-6) on the unit, remote control, or touch screen. The channel will begin playing and the unit will return to the Preset Mode. While in Preset Mode, press and hold an on-screen preset button (or 1-6 on the unit or remote control) to store the channel playing. 20 VM9511TS Category Guide Mode When Category Mode is selected, "Search Mode" and "CATEGORY" appear in the top half of the user interface. unit, remote control, or touch screen. The channel will begin playing and the unit will return to the Preset Mode. While in Preset Mode, press and hold an on-screen preset button (or 1-6 on the unit or remote control) to store the channel playing. Press the TITLE button (2) to return to the Category Mode main page and select a different category. Diagnostic Mode This feature is reserved for use by service professionals for troubleshooting. Parental Control By default, this feature is unlocked and all channels can be accessed by anyone listening to the radio. To lock a station, press the << button (22) on the remote control or V button (19) on the joystick until "Channel Number" is highlighted blue. Input the channel number to be locked. Press the << button on the remote control or \/ button on the joystick and select LOCK. Repeat this sequence for each channel to be locked. Press the >> button on the remote control or /\ button (18) on the joystick and navigate back up to Password - input 1264 and the small yellow lock will close indicating that the channel(s) are locked. Press the MENU button (1) twice to return to the main XM page. Direct Tuning To enter a station directly, perform the following steps. 1. Press the GOTO button (21) until the following screen appears. · · · · · · While in Search Mode, to switch between Channel and Category search modes, press the CH or CAT buttons in the touch screen. Press the >> button (14) on the remote control, the /\ button (18) on the joystick, or the > button on the touch screen to view the next six categories. Press the << button (22) on the remote control, the V button (19) on the joystick, or the < button on the touch screen to view the previous six categories. Press the on-screen SCAN button to preview each channel in the selected category for 10 seconds. Press the on-screen button to return to the Preset Mode screen. Press the on-screen MENU button to access the XM Setup Menu. 2. 3. Use number keys on the remote control to enter the desired XM radio station. You must enter a 3 digit number (for example, 004). Press the >/|| button (18) on the remote control or the joystick ENTER button (20) on the unit or just let the keypad "time out" after 4 seconds and the station will be entered automatically. Use the on-screen "CLR" button to correct entry mistakes and "OK" to enter the channel number. XM Setup Menu While in XM radio mode, press the MENU button (1) on the remote control to view the XM Setup Menu. To select a station in a specific category, perform the following steps. 1. To select a category, press the corresponding preset number (1-6) on the front of the unit, the remote control, or the touch screen. Once a category is selected, the stations in that category will be displayed on the screen. Press the >> button (14) on the remote control, the /\ button (18) on the joystick, or the > button on the touch screen to view the next six stations. Press the << button (22) on remote control, the V button (19) on the joystick, or the < button on the touch screen to view the previous six stations in the selected category. To select a channel while in Category Guide mode, press the corresponding preset number (1-6) on the 2. 3. Press MENU to exit the current submenu or menu and return to the previous screen. 21 VM9511TS DVD/VCD VIDEO OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays "PARKING" with a blue background. Rear video screens, if applicable, will operate normally. Using the Touch-Screen Controls The touch key areas for DVD playback are outlined below. NOTE: For VCD play, the repeat function is not available if PBC is on. Sectional Repeat Function (A-B) Use the A-B function to define a specific area of a disc to repeat. · · Press the REPT A-B button (6) on the remote control to set the start point (A) of the repeated section. Press the REPT A-B button again once you reach the desired end point (B) of the repeated section. The selected portion of the DVD will now repeat continuously. Press the REPT A-B button again to cancel the A-B section setting and stop repeat play. Opening/Closing the TFT Video Screen Opening the TFT Screen To open the TFT video screen, press the OPEN button (1). The unit beeps and then opens. Closing the TFT Screen Press the OPEN button (1) again to close the TFT screen. If the screen is in the "IN" position, it moves out before closing. · Insert/Eject Disc Upon inserting a DVD disc, DVD mode is entered and disc play begins. NOTE: If Parental Lock (Rating) is activated and the disc inserted is not authorized, the 4-digit code must be entered and/or the disc must be authorized (see "RATING (Parental Lock) Menu" on page 27). You cannot insert a disc if there is already a disc in the unit or if the power is off. NOTE: DVD-R and DVD-RW will not play unless the recording session is finalized and the DVD is closed. A ­ Return to MAIN MENU B ­ DISP key: Displays playing information C ­ Select previous chapter D ­ Select next chapter E ­ Display the following on-screen controls: Menu, >/||, , |<<, >>|, <<, >>. Random Playback With a DVD, VCD, or CD playing, press the RDM button (33) on the remote control to activate random playback and play all chapters/tracks in random order. "On" appears on the screen. Press the >>| button (19) on the remote control or the > button on the joystick (17) to play the next random track. Press the RDM button again to turn random play off. NOTE: When a VCD is playing with PBC turned "On", activating random playback automatically turns PBC off. Controlling Playback Stopping Playback Touch the stop button ( ) on the screen or press the / BAND button (20) on the remote control to stop DVD play. Pausing Playback Touch the play/pause button (>/||) on the screen or press the >/|| button on the remote control (18) to suspend or resume disc play. Slow Motion Playback Press the << button (22) on the remote control or the V button (19) on the joystick to play the current title in slow motion at 1/ 2, 1/4, 1/6 or 1/7, the normal speed. Press >/|| (18) to resume normal play. Continue pressing the << or V button to slow reverse. Repeat Playback Press the REPT button (7) on the remote control to alter repeat mode according to the following: · · · DVD: Repeat Title, Repeat Chapter, Repeat Off VCD (PBC Off): Repeat Single, Repeat Off MP3: Repeat Single, Repeat Folder, Repeat Off Accessing the DVD Menu Press the MENU button (1) on the remote control to recall the main DVD menu. Use the directional (arrow) buttons (<, >, /\ & V) on the joystick (16, 17, 18, 19) to select a title from the menu. Press the TITLE button (2) on the remote control to select a different title for playback. Press the >/|| button (18) on the remote control or the ENTER (joystick) button (20) to confirm your selection and begin playback. Ejecting a Disc Press the button (21) on the unit or remote control (35) to eject the disc. The unit automatically reverts to Tuner mode. You may eject a disc with the unit powered off. The unit will remain off after the disc is ejected. Reset the Loading Mechanism If the disc loads abnormally or an abnormal core mechanism operation occurs, press and hold the button (21) on the unit or remote control (35) to reset the loading mechanism. Normal operation resumes. Moving Through Chapters Press the >>| button (19) on the remote control or the > button on the joystick (17) to advance to the next chapter on the DVD. Press the |<< button (17) on the remote control or the < button on the joystick (16) to move to the previous chapter. Accessing DVD Mode To switch to DVD mode when a disc is already inserted, press the SRC button (15) on the front panel or remote control (8) until "DVD" appears at the bottom of the screen. 22 VM9511TS Fast Forward/Fast Reverse Press the >> button (14) on the remote control or the /\ button (18) on the joystick to fast forward. Keep pressing and releasing the button to increase the rate from "2X" to "4X", "8X", and "20X". Continue pressing the >> or /\ button to fast reverse. · For DVD mode, you can choose Time or Title/Chapter search. DVD Search Time ­ Go to specific time in current title Title/Chapter ­ Go to specific time in a chapter · For VCD mode, press the GOTO button to choose between Track Search, Disc Search and Exit. VCD Track Search Time ­ Go to specific time in the current track Track ­ Go to specific track VCD Disc Search Time ­ Go to specific time on disc Track ­ Go to specific track 3. 4. Enter a time into the field using the numeric keypad (29) on the remote control. Press the >/|| button (18) on the remote control or the ENTER (joystick) button (20) to go to the specified location on the disc. Press the GOTO button again to exit. Multi-Language Discs (DVD Only) Changing Audio Language If you are watching a disc recorded in multiple languages, press the AUDIO button (5) on the remote control to choose a language. Changing Subtitle Language If you are watching a disc recorded in multiple languages with subtitles, press the SUBTITLE button (9) on the remote control to choose the language in which you would like the subtitles to appear. NOTE: During VCD playback, press the AUDIO button (5) on the remote control to choose between Left Channel, Right Channel, and Stereo. Scanning Press the SCN button (34) on the remote control to play the first ten seconds of each chapter. Press SCN again to stop the scan function and play the current chapter. Selecting 2-Channel and 6-Channel Audio Playback 2-Channel Audio (Down Mix) Support for CD, SD Card and DVD Linear pulse code modulation (LPCM) and pulse code modulation (PCM) support is available for CD, SD Card and DVD discs when 2-channel audio is selected. 6- Channel Audio Support for CD, SD Card and DVD Pro-Logic II is available for decoding analog or digital 2channel down mixed sources. Dolby Digital is available for decoding digital bit-stream sources. NOTE: 2-channel audio support is available for AM/FM tuner, TV tuner, Aux Input, XM, iPod and Navigation only. 6-channel audio support is available for DVD/CD/CD-R and SD card. Table 10: Speaker Output Options Speaker Setup 2CH mode Play 2-channel (down mix) audio in 6-channel mode with ProLogic II "ON" Play 6-channel audio in 6-channel mode with Dolby Digital "ON" PBC (Play Back Control - VCD Only) For VCDs with play back functionality, play back control (PBC) provides additional controls for VCD playback. Press the MENU button (1) on the remote control to toggle the PBC function "On"/"Off". Once PBC is on, playback starts from track one of the play list. NOTE: When PBC is activated, fast forward, slow playback, and previous/next track are available. Repeat and direct track selection are not available. When PBC is activated, selecting random, scan, or search playback automatically deactivates PBC. 5. SubWoofer X Playback Information During DVD and VCD playback, press the INFO button (10) on the remote control to display playback information on the screen, including the media playing and current playback time. DVD Playback Information The following information is displayed at the bottom of the screen during DVD playback: Front Spkr X X Rear Spkr X X Center Spkr X Direct Chapter / Track Selection During DVD, VCD and CD playback, you can use the numeric keypad on the remote control (29) to access a track directly. X X X X Viewing an Alternate Picture Angle (DVD Only) Some DVDs contain scenes that have been shot simultaneously from different angles. For discs recorded with multiple angles, press the ANGLE button (13) on the remote control to toggle available angles of the on-screen image. Goto Search During DVD or VCD playback, perform the following steps to use the GOTO feature to access a specific location on a disc: 1. 2. Press the GOTO button (21) on remote control to enter "GO TO" mode. Press the >> or << buttons (14, 22) on the remote control or the < or > buttons (16, 17) on the joystick to select a category (highlighted in blue). · Zooming Press the ZOOM button (23) on the remote control to enlarge and pan through the video image using the following options: "Q1", "Q2", "Q3", and "OFF". · T : 5/8 ­ "5 / 8" indicates the fifth of 8 titles on the DVD is currently playing. · C : 2/16 ­ "2 / 16" indicates that the second of 16 titles on the DVD is currently playing. 00:41:28 ­ "00:41:28" indicates the playback time of the current title. 23 VM9511TS · 2 / 6 Eng ­ The language display information indicates the second language out of 6 (English) is currently being used. · · EQ: FLAT ­ The equalizer setting is FLAT. Loud: Level 1 ­ The Loud option is set to Level 1 loudness. The following information appears at the bottom of the screen during DVD playback: Front: DVD/CD Rear: AUXIN Dolby Digital Bypass General Disc Information Table 11: Disc Properties Symbo l 12cm Disc Properties Single side single layer (DVD-5) Single side double layer (DVD-9) Double side single layer (DVD-10) Double side double layer (DVD-18) Max Play Time (MPEG 2 Method) 133 minutes 242 minutes 266 minutes 484 minutes (MPEG 1 Method) 74 minutes 74 minutes · · Front: DVD is the current playback source for the front zone. Rear: AUX IN is the current playback source for the rear zone. "Dolby Digital" is the selected playback audio encoding process. Bypass indicates that the ASP (Audio Signal Processor) is being bypassed when Dolby Digital decoding is active. Single side single layer (VCD) VCD Playback Information The following information is displayed on the screen during VCD playback: Single side single layer Table 12: Disc Symbols Symbol · · · VCD2.0 ­ Format of current disc. T: 6/18 ­ "6/18" indicates the sixth of 18 tracks on the VCD is currently playing. 00:02:18 ­ "00:02:18" indicates the playback time of the current track. Meaning Number of voice languages recorded. The number inside the icon indicates the number languages on the disc (maximum of 8). Number of subtitle languages available on the disc (maximum of 32). Number of angles provided (maximum of 9). The following information appears on the screen during VCD playback in 6-Channel mode: Front: DVD · · Rear: AUXIN MPEG MOVIE Front: DVD ­ "DVD" is the current playing source for the front zone. Rear: AUX IN ­ "AUX IN" is the current playing source for the rear zone. "MPEG" is the decoding method in use. "Movie" indicates that movie effects are being applied to the audio sound track from the VCD. Aspect ratios available. "LB" stands for Letter Box and "PS" stands for Pan/Scan. In the example on the left, the 16:9 video can be converted to Letter Box video. Indicates the region code where the disc can be played. · Region 1: USA, Canada, East Pacific Ocean Islands · Region 2: Japan, Western Europe, Northern Europe, Egypt, South Africa, Middle East · Region 3: Taiwan, Hong Kong, South Korea, Thailand, Indonesia, South-East Asia · Region 4: Australia, New Zealand, Middle and South America, South Pacific Ocean Islands/ Oceania · Region 5: Russia, Mongolia, India, Middle Asia, Eastern Europe, North Korea, North Africa, North-West Asia · Region 6: Mainland China · ALL: All regions The following information appears on the screen during VCD playback in 2-Channel mode: · · Front: DVD ­ "DVD" is the current playing source for the front zone. Rear: AUX IN ­ "AUX IN" is the current playing source for the rear zone. 24 VM9511TS DVD/DISC SETUP MENU NOTE: A DVD/disc must be loaded into the mechanism and playing prior to accessing the DVD Setup menu. While the DVD/disc is playing, press the DVD SETUP button (30) on the remote to access the DVD Setup menu. In "DVD Setup" mode, "LANGUAGE", "VIDEO", "AUDIO" "SPK CONFIG", "PRO-LOGIC II", and "RATING" (parental lock) are available for setup. These operations can be performed using the remote control or joystick controls. can also touch the on-screen menu selection to access that menu. DIRECTION BUTTONS Table 13: LANGUAGE Menu Features Setting Audio Options English Function Select the default language in which you would like audio (when optional) to be played. Select the default language in which you would like the DVD menu (if applicable) to be displayed. Return to previous menu. DVD Menu English BACK Accessing the DVD Setup Screen Setup can be performed by pressing the dedicated button on the remote control, or by pressing the SRC button (15) on the front panel. For system settings, press the DVD SETUP button (30) on the remote control or touch "SETUP" on the screen to enter the "SETUP" menu. "SYS SETUP" is highlighted in green. To access the "DVD SETUP" Menu, press the V button (7) on the remote control to choose the "DVD SETUP" option, then press the >/|| button (18), or just touch "DVD SETUP" on the screen. "LANGUAGE" is highlighted in green. Selecting a Feature for Adjustment Once inside a menu, press the >> or << buttons (14, 22) on the remote control or the /\ or V buttons (18, 19) on the joystick to select the feature to be adjusted. Adjusting a Feature 1. Enter the option field for the feature you want to adjust by pressing the >/|| button (18) on the remote or by pressing the ENTER (joystick) button (20) on the unit. A submenu appears in a second row with the selected option highlighted in light blue. 2. Select a new value by pressing the >> or << buttons (14, 22) on the remote control or the /\ or V buttons (18, 19) on the joystick. 3. Confirm your selection by pressing the <<, |<<, or >>| buttons (22, 17, 19) on the remote control, or the < or > button (16, 17) on the joystick. The new value is highlighted in light blue and setup is complete. VIDEO Menu Table 14: VIDEO Menu Features Setting TV Shape (Aspect Ratio) Options 4:3 PS 4:3 LB 16:9 Function With 16:9 display, the left and right sides are cut off. With 16:9 display, the top and bottom are cut off. Image is presented in wide view with a 16:9 aspect ratio. Angle indicator (if applicable) is shown. Angle indicator is not shown. Angle Mark View Mode On Off Fill Original H Fit W Fit Fit to Scrn Pan Scan LANGUAGE Menu If a DVD supports more than 1 Subtitle or Audio language, all the languages are available for selection during playback. If the selected language is not supported by the DVD, then the default language is used. During playback, press the SUBTITLE (9) or AUDIO (5) button on the remote control to change the language directly. This will not affect the DVD menu settings. NOTE: Once the DVD setup is complete, the settings are memorized. To return to the factory default settings, press the RESET button (25) on the front panel. Accessing a Menu To access a menu (LANGUAGE, VIDEO, AUDIO, SPK CONFIG, PRO-LOGIC II, or RATING), press the direction buttons on the joystick (16, 17, 18, 19) or remote control (14, 17, 18, 19, 22) to highlight the desired menu in green. You Table 13: LANGUAGE Menu Features Setting