User manual AXIS 1650

AXIS 1650 User's Manual The Network Print & Scan Server for Canon Printers and Multifunctional Products Including support for Canon Advanced Printing Technology Canon Advanced Raster Printing System as well as Canon BubbleJet Printers AXIS 1650 User's Manual 1 Safety Notices Section 1 Important: Electromagnetic Compatibility (EMC) USA Safety Notices Take some time to read through the safety notices before installing the print server. Please observe all safety markings and instructions when using this product. Observe "Important:" in the text to avoid operational impairment. Do not proceed until you have fully understood the implications. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - reorient or relocate the receiving antenna - increase the separation between the equipment and receiver - connect the equipment into an outlet on a circuit different from that to which the receiver is connected - consult the dealer or an experienced radio/TV technician for help. Shielded (STP) network cables must be used with this unit to ensure compliance with the class B limits. Europe Japan This digital equipment fulfils the requirements for radiated emission according to limit B of EN55022, and the requirements for immunity according to EN55024 residential, commercial, and light industry. Compliance is not valid for unshielded network cables. This is a class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Compliance is not valid for unshielded network cables. This electronic device meets the requirements of the Radiocommunications (Electromagnetic Compatibility) Standard 1998 AS/NZS 3548. Compliance is not valid for unshielded network cables. Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions, please inform your local Axis office, which can be found on www.axis.com. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. Axis Communications AB makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material. AXIS IP JumpStarter, AXIS CAPT Print Monitor. Adobe Acrobat Reader, Canon, Ethernet, Internet Explorer, Microsoft, NetScape, NetSpot Device Installer (NSDI), Windows, are registered trademarks of the respective holders. Axis AB has intellectual property rights relating to technology embodied in the product that is described in this document. In particular, and without limitation, these intellectual property rights may include one or more of the patents listed at http://www.axis.com/patent.htm and one or more additional patents or pending patent applications in the US and other countries. Australia Liability Axis' Trademarks Other Trademark Acknowledgments Patent Information AXIS 1650 User's Manual Revision 2.2 Part No: 25081 Date: 06-03-14 Copyright © Axis Communications AB, 2006 2 AXIS 1650 User's Manual Table of Contents Section 2 Table of Contents Section 1 Section 2 Section 3 Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 5 5 Section 4 Section 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Print Server Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . 10 Set the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Set an IP Address with NetSpot Device Installer software 14 IP Address Host Names . . . . . . . . . . . . . . . . . . . . . . . . 15 Windows Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Installing Printer Ports using AXIS CAPT Print Monitor 17 Print Server Installation using AXIS CAPT Print Monitor in Windows 2000, XP and Server 2003 . . . . . . . . . . . . . . 17 Print Server Installation using AXIS CAPT Print Monitor in Windows 98 and Me . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Print Server Installation using the Standard TCP/IP Port in Windows 2000/XP/2003 . . . . . . . . . . . . . . . . . . . . . . . 25 Adding Printers in NetWare . . . . . . . . . . . . . . . . . . . . . . . . . 28 Setup using NetWare 6.5 . . . . . . . . . . . . . . . . . . . . . . . 28 Setup using NetWare 6.0 . . . . . . . . . . . . . . . . . . . . . . . 34 Print Server Management and Configuration . . . . . . . . . . . . 40 Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . 40 Print Server Management from the Embedded Web Pages 40 Accessing the Web Pages . . . . . . . . . . . . . . . . . . . . . . 41 Services Available from the User Mode . . . . . . . . . . . . 42 Services Available from the Admin Mode . . . . . . . . . . . 44 Setting General Parameters . . . . . . . . . . . . . . . . . . . . . 47 Setting Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Setting Network Protocol Parameters . . . . . . . . . . . . . 49 Print Server Management Using FTP . . . . . . . . . . . . . . 52 Print Server Management Using SNMP . . . . . . . . . . . . 53 Scanning with AXIS 1650 . . . . . . . . . . . . . . . . . . . . . . . . . . Installing AXIS ScanClient . . . . . . . . . . . . . . . . . . . . . . Using AXIS ScanClient . . . . . . . . . . . . . . . . . . . . . . . . . Invoking a Scan from your Computer . . . . . . . . . . . . . . 54 54 56 56 3 Section 6 Section 7 Section 8 Section 9 AXIS 1650 User's Manual Table of Contents Invoking a Scan from the Canon Device . . . . . . . . . . . 59 Section 10 Section 11 Section 12 Section 13 Section 14 The Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Enabling Unicast Network Communication . . . . . . . . . . . . . 64 Internet Connection Firewall in Windows XP SP2 . . . . . . . . 68 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 4 AXIS 1650 User's Manual Preface Section 3 Preface Thank you for purchasing the AXIS 1650. This product has been developed to connect your Canon printer anywhere in your network, allowing all network users access to shared printer resources. About this Manual This manual is applicable for the AXIS 1650 print server with firmware version 2.00 or later, providing introductory information as well as detailed instructions on how to set up and manage the print server in various network environments. It is intended for everyone involved in installing and managing the print server. To fully benefit from this manual, you should be familiar with basic networking principles. These instructions are based on the settings in a new and unconfigured print server. To reload the default parameters, you can perform a Factory Default, which will restore all default settings. See "The Test Button" on page 61. About Axis Axis increases the value of network solutions. The company is an innovative market leader in network video and print servers. Axis' products and solutions are focused on applications such as security surveillance, remote monitoring and document management. The products are based on in-house developed chip technology, which is also sold to third parties. Axis was founded in 1984 and is listed on the Stockholmsbörsen (XSSE:AXIS). Axis operates globally with offices in 14 countries and in cooperation with distributors, system integrators and OEM partners in 70 countries. Markets outside Sweden account for more than 95 % of sales. Additional information about Axis can be found at www.axis.com Support Services Should you require any technical assistance, please contact your Axis reseller. If your questions cannot be answered immediately, your Axis reseller will forward your queries through the appropriate channels to ensure a rapid response. AXIS 1650 User's Manual 5 Preface If you are connected to the Internet, you can: · · · · Download user documentation and firmware updates Find answers to previously resolved problems in the FAQ database. Search by product, category or phrase Report problems to Axis support staff by logging in to your private support area Visit the Axis support Web: www.axis.com/techsup 6 AXIS 1650 User's Manual Product Overview Section 4 Package Contents Product Overview Hardware Model AXIS 1650 Model/ Part Number 0214-001- 01 0214-001- 02 With firmware version 2.00 or higher 0214-005-01 0214-005-02 With firmware version 2.00 or higher 20119 20208 Network Print Server AXIX 1650 Japan Adhesive Holder & Clip USB Cable Power Adapter Network Cable CD Printed Material Optional accessories (not included in package) Cables ACC AXIS CLIPS K 70 cm, 28 inches USB cable supports USB Low-Speed and Full-Speed. Hi-Speed is not supported. PS-H RJ 45 Shielded CAT5 0.5M AXIS 1650 CD AXIS 1650 Quick Installation Guide WARRANTY AXIS SERVERS 1YR Description Extension Cable Centronics to Mini Centronics Cable 16283 rev. 1.0 or higher rev. 1.0 or higher 21681 Part Number 13522 16453 The AXIS 1650 Network Print Server Parallel printer port (LPT1) Test button Ethernet connector Network indicator Power adapter connector USB Printer Port (USB1) Power indicator Supported Devices AXIS 1650 is developed to network Canon printers and multifunctional products. AXIS 1650 supports host-based printing methods such as Canon Advanced Printing Technology, Canon Advanced Raster Printing System and other printer types such as Canon BubbleJet. If your Canon device also functions as a scanner, you can use your AXIS 1650 as a scanner server as well. Important: Devices from other manufacturers than Canon are not supported. AXIS 1650 User's Manual 7 Product Overview Supported Environments The AXIS 1650 supports printing over TCP/IP from the following clients: · · · · · · Windows 98 Windows Me Windows 2000 Windows XP Windows Server 2003 Netware Installation and Integration The installation of the AXIS 1650 and its integration into the network is performed using one of these software combinations: · · · AXIS IP JumpStarter (for IP setting) and then AXIS CAPT Print Monitor (for printer installation) Canon NetSpot Device Installer (for IP setting) and then AXIS CAPT Print Monitor (for printer installation) AXIS ScanClient to enable scanning through the AXIS 1650. AXIS IP JumpStarter, AXIS CAPT Print Monitor and AXIS ScanClient are available free of charge from the AXIS 1650 CD and on www.axis.com NetSpot Device Installer is available on www.canon.com Configuration and Management Configuration and management of AXIS 1650 is performed using the TCP/IP protocol. The main method is using a standard Web browser. See "Print Server Management from the Embedded Web Pages" on page 40. TCP/IP The AXIS ETRAX chip has been specifically designed for LAN products and benefits users with a faster throughput than a direct PC-to-printer connection. With a sustained data throughput of over 1 Mbytes per second (100baseTX) the AXIS 1650 is fast. ECP high-speed communication is supported. You can assign a password that restricts unauthorized configuration of the AXIS 1650. The AXIS 1650 embedded Web pages allow you to continuously monitor printer status. Additionally, the AXIS 1650 supports SNMP for remote monitoring. You can upgrade the AXIS 1650 Flash memory over the network. This allows you to quickly update and enhance the operational features of your AXIS 1650 when new print server software becomes available. AXIS 1650 User's Manual Printing Protocol: Speed Security: Monitoring: Future proof: 8 Product Overview Printer Ports · One Low- and Full-Speed USB 1.1 port that also works with USB 2.0. Hi-Speed is not supported. · One high-speed IEEE 1284 compatible parallel port that plugs directly into the printer´s parallel port. AXIS 1650 is featured with two ports for ease of integration with most Canon printers. There is however no support for handling two connected printers simultaneously. AXIS 1650 User's Manual 9 Print Server Installation Section 5 Print Server Installation Follow these steps to install and configure your AXIS 1650: 1. Connect the Hardware, on page 10 2. Set the IP Address, on page 11 3. Windows Installation, on page 17 Connect the Hardware Parallel printer port (LPT1) Test button Ethernet connector Network indicator Power adapter connector USB Printer Port (USB1) Power indicator Backside label of print server The print server's MAC/Ethernet address is based on its serial number (S/N). Example: If the print server's serial number is 00408c181cf0, the Ethernet/MAC address will be 00-40-8c-18-1c-f0 1. Make sure that your printer is switched off and that the print server's power adapter is disconnected. 2. Locate the serial number, found on the underside label of the print server, and write it down. You will need this number to configure the print server. 3. Either connect the printer to the USB port using the USB cable, or connect the printer directly to the LPT port or use a printer cable. Note: AXIS 1650 is featured with two ports for ease of integration with most Canon printers. There is, however, no support for handling two connected printers simultaneously. 4. Connect the print server to the network using a shielded twisted pair (category 5) RJ45 cable, 10baseT or 100baseTX. 5. Switch on the printer and make sure it is ready for use. 6. Connect the power adapter to the print server. The power indicator will light up. When the network indicator starts to flash, the print server is correctly connected to the network. 10 AXIS 1650 User's Manual Print Server Installation 7. Optionally, you can mount the print server e.g. on the back of the printer or on a wall, using the supplied clip and holder. Adhesive Holder Adhesive Clip Fasten to print server by peeling off adhesive tape. Fasten to mounting surface by peeling off adhesive tape. Set the IP Address Before setting the IP address, make a note of the print server's serial number (S/N), located on its backside label. See Backside label of print server, on page 10. You should obtain an unused IP address from your network administrator Method AXIS IP JumpStarter software Platform Windows Comment Axis software that allows you to find print servers in your network and assign an IP address to them. See "Set a Static IP Address using AXIS IP JumpStarter" on page 11 Windows Arp/Ping Unix/ Linux Canon's NetSpot Device Installer software See "Set a Static IP Address using ARP in Windows 98/Me/2000/XP/2003" on page 13 See Set a Static IP Address using ARP in UNIX, on page 13 Canon software that allows you to find print servers in your network and assign an IP address to them. See "Set the IP Aaddress using NetSpot Device Installer" on page 14 Windows It is not possible to obtain a dynamic IP address using DHCP, since DHCP is disabled by default in AXIS 1650. To enable DHCP in the print server, see DHCP Enabled, on page 50. You can, however, obtain a DHCP address for the print server via AXIS IPJumpStarter or NetSpot Device Installer. If you choose to obtain a DHCP address for the print server from these programs, the DHCP function will be enabled in the print server. Set a Static IP Address using AXIS IP JumpStarter AXIS IP JumpStarter is an application that helps you to locate your Axis print server on the network and assign an IP address to it. AXIS 1650 User's Manual 11 Print Server Installation 1. Install AXIS IP JumpStarter, it is available on the AXIS 1650 CD and on www.axis.com 2. Select a print server from the Serial Number list. All AXIS 1650 appear with the default IP address 192.168.0.90. If you are installing several AXIS 1650, check the Serial Number to locate a specific print server. All AXIS 1650 have the default IP address 192.168.0.90 Change this default IP address to either a static IP address or to a DHCP address. 3. From the Server menu, select Set IP Address. The Set IP Address dialog appears. 4. Click the radio button that corresponds to your choice of IP setting method (static or dynamic using DHCP). When assigning a static IP address you also have to define the Subnet Mask and Default Gateway. 5. Click OK to save your settings. 6. You may be prompted to enter the server root password (by default set to ), click OK and the print server will appear in the list with the assigned IP address. 7. To verify that you have access to the print server's Web pages, highlight the print server in the list and select Server Home Page from the Server menu. 8. You have now finished the procedure of setting the IP address. Continue to Windows Installation, on page 17. 12 AXIS 1650 User's Manual Print Server Installation Set a Static IP Address using ARP in Windows 98/Me/2000/XP/2003 1. Open a Command Prompt and type: arp -s ping -l 479 Example: arp -s 192.168.3.191 00-40-8c-18-1c-f0 ping -l 479 192.168.3.191 2. If the host returns Reply from 192.168.3.191 ... or a similar message, the IP address has been set successfully. If the host returns Request timed out you need to reboot the print server and perform steps 1-2 above again. Rebooting the print server is done by disconnecting and then re-connecting the print server's power adapter. 3. Access the print server's Web pages ( - See page 41), select Admin | Network Settings | Detailed View | TCP/IP and define the Default Router and Subnet Mask. Make sure DHCP, BOOTP and RARP are disabled. You have now set the IP address of the print server. Continue with Windows Installation, on page 17. Note: When you execute the ping command for the first time, you will experience a significantly longer response time than usual. Follow the instructions below to set the IP address using ARP. 1. Type the following commands in the shell window: arp -s temp ping -l 479 Set a Static IP Address using ARP in UNIX Example: arp -s 192.168.3.191 00:40:8c:18:1c:f0 temp ping -l 479 192.168.3.191 2. The host will return 192.168.3.191 is alive or a similar message. This indicates that the address has been set and that the communication is established. 3. Access the print server's Web pages ( - See page 41), select Admin | Network Settings | Detailed View | TCP/IP and define the Default Router and Subnet Mask. Make sure DHCP, BOOTP and RARP are disabled. Notes: · · The ARP command varies between different UNIX systems. Some BSD type systems expect the host name and node address in reverse order. When you execute the ping command for the first time, you may experience a significantly longer response time than usual. AXIS 1650 User's Manual 13 Print Server Installation Set an IP Address with NetSpot Device Installer software NetSpot Device Installer is software from Canon that allows you to assign an IP address and manage Canon devices connected to your network. NetSpot Device Installer software is supplied on CD-ROM with your Canon printer and on www.canon.com Depending on the provided CD-ROM, NetSpot Device Installer may not be included. If this is the case, please download NetSpot Device Installer from www.canon.com Install NetSpot Device Installer 1. In Windows 2000/XP, log on as an Administrator before installing. Insert the CD-ROM supplied with your Canon printer into the CD-ROM drive of your computer. 2. In Windows Explorer, double-click the CD-ROM drive icon. 3. Double-click NetSpot_Device_Installer => Windows => nsdisetup.exe 4. A license agreement will be shown in the window. Check the contents and click Yes. 5. Specify the program destination folder and click OK. The installation will launch. If you check "Add to Start menu", you can add NetSpot Device Installer to your Windows Start menu. 6. When the installation is finished, click OK. You can now start the program, see Set the IP Aaddress using NetSpot Device Installer, on page 14. Set the IP Aaddress using NetSpot Device Installer Follow these instructions to set the IP address using NetSpot Device Installer: 1. Start the program. The main window will open. After a while a list of devices detected on the network will be displayed. 2. Select the AXIS 1650 that displays the unit's MAC address and default IP address 196.168.0.90 The MAC address is based on the Serial Number (S/N) of your AXIS 1650 and is printed on the underside label of the print server. 3. From the Device menu, select Initial Settings. 14 AXIS 1650 User's Manual Print Server Installation 4. From the Initial Settings dialogue box, select the AXIS 1650 print server from the Product Type drop-down list and click Next. 5. Next, configure the TCP/IP protocol: Select Manual Setting Enter IP Address Enter Gateway Address Enter Subnet Mask The Broadcast Address is filled in automatically 6. After you have finished the configuration, click OK. Note: If you get a message reading "Resetting device", click OK. 7. Click OK. Your printer's protocol configuration is now finished and your AXIS 1650 has received an IP address. Continue to Windows Installation, on page 17. IP Address Host Names If you are using host names, you can map a unique host name to the IP address. Refer to your system manuals or to your network administrator for instructions on how to perform name mapping on your system. AXIS 1650 User's Manual 15 Print Server Installation Notes · · · · · · · · You need to know the Ethernet address of your AXIS 1650 to perform the installation. The Ethernet address is based on the serial number of your AXIS 1650. For example, an AXIS 1650 with the serial number of 00408C181CF0, will have the corresponding Ethernet address of 00 40 8C 18 1C F0. The serial number is located on a label on the backside of the print server. DO NOT use the IP addresses shown in the following examples when installing the AXIS 1650. ARP/Ping operates on single network segments only, i.e. it cannot be used over routers. The default host name of the print server is 'AXIS' followed by the last 6 digits in the serial number. e.g. AXIS181636. The host name is changed in the Print server name field in Admin | General Settings. The host name limitations conclude that if you want to register the same host name at a WINS server and a DDNS server, the host name should be no longer than 15 characters and it should only contain the characters `A-Z', `a-z', '0-9' and `-'. Refer to your system manuals or to your network administrator for instructions on how host name resolutions are performed on your system. At least one WINS server IP address must be included in the DHCP scope if you are using WINS. Immediately after the IP address has been received, the AXIS 1650 registers its host name and IP address on the WINS server. If the host name has not been mapped to the IP address, you can still perform the following instructions to download the IP address. In this case, simply replace the host name entry with the IP address wherever required. 16 AXIS 1650 User's Manual Windows Installation Section 6 Windows Installation Installing Printer Ports using AXIS CAPT Print Monitor AXIS CAPT Print Monitor is a Windows component that has been developed for network printing. AXIS CAPT Print Monitor is the recommended tool for Canon printers, including CAPT, Canon Advanced Raster Printing System and BubbleJet. AXIS CAPT Print Monitor allows your AXIS 1650 to be connected in the same simple fashion as a local printer port and once installed, it is automatically initialized upon system start-up. AXIS CAPT Print Monitor needs to be installed on each workstation for peer-to-peer printing. Refer to the instructions relevant to your network on how to install a printer using AXIS CAPT Print Monitor: · · Print Server Installation using AXIS CAPT Print Monitor in Windows 2000, XP and Server 2003, on page 17. Print Server Installation using AXIS CAPT Print Monitor in Windows 98 and Me, on page 22. See also Print Server Installation using the Standard TCP/IP Port in Windows 2000/XP/2003, on page 25. Print Server Installation using AXIS CAPT Print Monitor in Windows 2000, XP and Server 2003 1. Install the AXIS CAPT Print Monitor on your workstation. The software is available on the AXIS 1650 CD and on www.axis.com 2. Launch the software installation and click Next. AXIS 1650 User's Manual 17 Windows Installation 3. Read the License Agreement and click Yes if you accept the terms. 4. Leave this check-box unchecked* and click Next. (If you want to disable broadcast status updates and enable unicast, see Enabling Unicast Network Communication, on page 64.) Windows XP/Server 2003 only: Make sure the Allow this application to process incoming network printer information on the local subnet checkbox is checked. Must be checked! In Windows XP SP 2, UDP port 10260 must be open in the Internet Connection Firewall when using Broadcast communication. UDP port 10260 is opened automatically in the Internet Connection Firewall when 18 AXIS 1650 User's Manual Windows Installation Windows XP SP2 is installed, if Allow this application to process incoming network printer information on the local subnet is checked. 5. Click Finish to finish the installation. 6. Windows XP/Server 2003: Go to Start | Printers and Faxes and click the Add a Printer icon to start the Add Printer Wizard. (Windows XP Home Edition: Start | Control Panel | Printers and Faxes | Add a Printer). Click Next. Windows 2000: Go to Start | Settings | Printers and click the Add Printer icon to start the Add Printer Wizard. Click Next. AXIS 1650 User's Manual 19 Windows Installation 7. Select Local Printer attached to this computer. Make sure the Automatically detect and install my Plug and Play printer check box is not checked. Click Next. 8. Click the Create a new port radio button and select AXIS CAPT Port. Click Next. Note: AXIS CAPT Port is used for all Canon printers, including CAPT, Canon Advanced Raster Printing System and BubbleJet. 20 AXIS 1650 User's Manual Windows Installation 9. The AXIS CAPT Port pop-up window will appear. Select your AXIS 1650 from the Available network printers list and click OK. If your AXIS 1650 doesn't appear in the Available network printers list, enter its IP address and click Add. 10. Select Manufacturer and Printer from the driver list. Click Next. 11. Choose whether you want to keep the existing driver or to replace it. If you already have the printer's driver installed, you will be asked whether to keep it or to replace it. 12. Click Next. Supply a name for the printer and choose whether you want to make it your default printer. Click Next. 13. Choose whether you want to share the printer with other network users, print a test page, etc. Select the appropriate radio button and click Next and Finish. AXIS 1650 User's Manual 21 Windows Installation 14. Print a test page to verify. You have now completed the installation. Print Server Installation using AXIS CAPT Print Monitor in Windows 98 and Me Follow the procedure below to install TCP/IP Ports from a Windows 98/Me workstation: 1. Install the AXIS CAPT Print Monitor on your workstation. The software is available on the AXIS 1650 CD and on www.axis.com 2. Launch the software installation and click Next. 3. Read the License Agreement and click Yes if you accept the terms. 22 AXIS 1650 User's Manual Windows Installation 4. Leave this check-box unchecked and click Next. (If you want to disable broadcast status updates and enable unicast, See Enabling Unicast Network Communication, on page 64 for instructions.) 5. Click Finish to finish the installation. 6. Select Settings | Printers from the Start menu and double-click the Add Printer icon to start the Add Printer Wizard. 7. Select Local Printer, as the AXIS 1650 emulates a local printer port and click Next> 8. Choose an appropriate printer driver for your printer. If the desired driver appears in the manufacturer and models list dialog, highlight your selection and click Next>. If the desired printer driver is not available, click the Have Disk... button. Insert the printer driver CD that was provided with your printer, select the CD drive and click OK. 9. Select the desired printer driver from the CD and click Next> AXIS 1650 User's Manual 23 Windows Installation 10. Select the port you wish to use and click OK. · The ports will appear in the format . is, by default, `AXIS' followed by the last six digits of the print server's serial number. Example: AXIS560B35. If you wish to install a remote TCP/IP port (and if the TCP/IP port does not appear in the list), select the LPT1 port. Continue with steps 11 and 12 and then follow the Remote Printer Port instructions below. · 11. Enter a descriptive name for your printer and click Next> 12. Click the checkbox if you want to print a test page and click Finish. Remote Printer Port 1. The printer you defined above is now displayed in the printers folder. Right-click the printer object and select Properties from the menu. 2. Click the Details tab and click Add Port... to display the available print server monitors. 3. Click Other, select AXIS CAPT Port and click OK. AXIS CAPT Port is used for all Canon printers, including CAPT, Canon Advanced Raster Printing System and BubbleJet. 4. Enter the IP address / host name of your print server. Click Add. 5. The port will be added to the list and highlighted. Click OK to return to the printer ports dialog and click Close. 24 AXIS 1650 User's Manual Windows Installation Print Server Installation using the Standard TCP/IP Port in Windows 2000/XP/2003 Follow the instructions below to use the Windows Standard TCP/IP Port to add a network printer in Windows 2000/ Windows XP/2003. Windows XP/ Server 2003: 1. Go to Start | (Settings) | Printers and Faxes and click the Add a Printer icon to start the Add Printer Wizard. Click Next. Windows 2000: 1. Go to Start | Settings | Printers and click the Add Printer icon to start the Add Printer Wizard. Click Next. 2. Select Local Printer attached to this computer and make sure the Automatically detect and install my Plug and Play printer check box is not checked. Click Next. 3. Click the Create a new port radio button and select Standard TCP/IP Port from the list. Click Next and the Add Standard TCP/IP Printer Port Wizard starts. Click Next. AXIS 1650 User's Manual 25 Windows Installation 4. In the Printer Name or IP Address field, enter the IP address of the print server. Example: 192.168.3.191. The Port Name field will be filled in automatically. Click Next. 5. Select Manufacturer and Printer from the lists. Click Next. 6. If you already have the printer's driver installed, you will be asked whether to keep it or to replace it. Click Next. Supply a name for the printer and choose whether you want to make it your default printer. Click Next. 7. Choose whether you want to share the printer with other network users, print a test page, etc. Select the appropriate radio button and click Next and Finish. 26 AXIS 1650 User's Manual Windows Installation 8. Next, from your desktop, go to Start | Printers (and Faxes). Highlight the installed printer and right-click, choose Properties, then Ports | Configure Port. 9. In the LPR Settings - Queue Name field, you will see the value "z". In the Queue Name field, type USB1 or LPT1, depending on which printer port you are using. Click OK and then Apply. 10. Print a test page to verify. You have now finished the installation. AXIS 1650 User's Manual 27 Adding Printers in NetWare Section 7 Adding Printers in NetWare This section describes how to continue the installation of the AXIS 1650 in a NetWare environment. iPrint Using iPrint in the NetWare environment, users simply point to a Web page that displays all printers available for installation. By clicking a printer, the iPrint client is installed (if not installed previously), the printer's driver is downloaded, and a printer is created on the user's workstation; thus, the user will be able to send documents to the printer from any application on the desktop. Depending on your NetWare version, go on to "Setup using NetWare 6.5" on page 28 or "Setup using NetWare 6.0" on page 34. If you intend to operate your AXIS 1650 in a multi-protocol, mixed environment, you should also proceed to the other relevant sections in this manual. Setup using NetWare 6.5 Start the iManager. Type https:///nps/iManager.html in the Address/Location field of your browser and press Enter. Example: https://nakoma.tl.com/nps/iManager.html. In the Roles and Tasks frame of the iManager, expand iPrint to make all commands available. Check Print Manager and Broker Make sure that NDPS is installed and that the Print Manager and the Broker both are loaded on your NetWare file server. You can check the status of NDPS by selecting Roles and Tasks | iPrint | Manage Print Manager, browse to the file server and select it. Ensure that the status is NDPS Manager active. 28 AXIS 1650 User's Manual Adding Printers in NetWare To check the state of the Broker, select Roles and Tasks | iPrint | Manage Broker. Its state has to be active as well. Create a Printer In the iManager, click Roles and Tasks | iPrint | Create Printer. The Create Printer dialogue appears. Type a name for the printer to be created (e.g. CanonMF). Keep the default Container name (e.g. axis). Select Print Manager name (e.g. NAKOMA_MANAGER.axis). Select Novell gateway as Gateway type and click Next. Configure Novell Gateway for the Created Printer To configure the gateway, enter Host IP address or Host name of the AXIS 1650 (e.g. 171.15.114.137). As default, PASSTHROUGH is suggested as LPR Printer name. Change this to USB1 or LPT1, depending on which device port the print server is connected to (or simply select the Port 9100 radio button for raw printing). Click Next. AXIS 1650 User's Manual 29 Adding Printers in NetWare Select Default Drivers for Your Platforms For each platform in your network, select the default printer drivers to install (the drivers presented are those registered in the Broker; new drivers can be added from the Manage Broker task). Click Next. You will now receive a confirmation that the request succeeded and that printer CanonMF.axis was created. Click OK. Manage the Newly Created Printer Select Roles and Tasks | iPrint | Manage Printer and specify which NDPS Printer to modify (e.g. CanonMF.axis). Click OK. To Browse for a Printer Next to the NDPS Printer name field, click the Browse icon. Browse to your default container to find the newly created printer (e.g. CanonMF), select AXIS 1650 User's Manual 30 Adding Printers in NetWare it in the Contents list and click Apply. Check Printer Health Select Roles and Tasks | iPrint | Manage Printer | Printer Health Monitor to check the health of the printer. AXIS 1650 User's Manual 31 Adding Printers in NetWare Click Back to return to the Manage Printer main page. Enable iPrint Support In the Manage Printer main page, click the Client Support tab. To enable iPrint support, check Enable iPrint support, click Apply and OK. Make the Newly Created Printer Available (Optional) Using the iPrint Map Designer tool, you can quickly make the newly printer available and accessible simply by clicking on its icon in a floor plan, showing where the printers are located. The tool lets you import own floor plans as background images that can be used to drag-and-drop printers onto actual locations. These maps are then published on a Web server so users can install printers that are closest to their location. 1. Using Microsoft Explorer, start maptool.html, which can be found in \Apache2\htdocs\ippdocs\. 2. Select a map from the Background drop-down list. 3. Select a Printer icon for the newly created printer and drag it to a suitable position in the design area, i.e. the floor plan. 4. Next to the Printer List field, click the Browse icon and enter the IP address or DNS name of the server where the Print Manager is running (e.g. 171.15.115.112). 32 AXIS 1650 User's Manual Adding Printers in NetWare 5. From the Printer List, select the printer agent you want associated with this printer icon (e.g. CanonMF). The Printer URL and Mouse Over Text will automatically be filled in with the printer agent information. Printer URL is the URL created for the printer when IPP was enabled for the printer (e.g. ipp://171.15.115.112/ipp/CanonMF). You should not need to change the URL. The Mouse over text will by default display the printer agent's name. You can override this information by entering the text you want to display when a user moves the mouse over the printer icon (e.g. Canon Multifunction). 6. In the Printer caption field, enter the information to display (e.g. AXIS 1650/Canon MF). 7. Click Save and save the map (e.g. as AXIS1650_usb). Installing the Printer Locally The printer is now accessible all over the network and will be installed on any client when needed. In case you need to install the printer locally, use Windows' Add Printer Wizard in the usual manner: 1. Ensure that iPrint Client is installed. 2. Start | Printers and Faxes | Add a printer. 3. Select Network printer and Browse for a printer. 4. Select NDPS Printers, select NDPS Controlled Access Printers. AXIS 1650 User's Manual 33 Adding Printers in NetWare 5. Select Container (e.g. Axis) and the printer (e.g. CanonMF). 6. Wait for the printer to be installed. 7. Finally, print a test page. Setup using NetWare 6.0 Setting up iPrint in a NetWare 6.0 environment is rather similar to performing the same task in the 6.5 version. Launch the iManager From a workstation, launch your browser and enter the following URL: https:///eMFrame/iManager.html. Note that this URL is case sensitive. The server IP address can also be a DNS name. Example: https://171.15.115.109:2200/eMFrame/iManager.html To have full access to all iManager features, you must log in as Admin of the tree. Check Print Service Manager and Broker Create a Printer Make sure that NDPS is installed and that the Print Service Manager and the Broker both are loaded on your NetWare file server. In the left frame, expand iPrint Management to make all commands available and click Create Printer. In the Create Printer dialogue, enter the information needed. Examples: Printer name: CanonMF Container name: axis Manager name: SIXPACK_MANAGER.axis Gateway type: Novell LPR gateway (LPR or IP) Click Next. 34 AXIS 1650 User's Manual Adding Printers in NetWare Configure Novell LPR Gateway for the Created Printer To configure the gateway, enter Host IP address of the AXIS 1650 (e.g. 171.15.114.137). Instead of the Host IP address you can use the Host name (e.g. CanonMF.tl.com). As Printer name, enter the printer port (e.g. USB1). Click Next. Select Default Drivers for Your Platforms For each platform in your network, select the default printer drivers to install (the drivers presented are those registered in the Broker; new drivers can be added from the Manage Broker task). Click Next. You will now receive a confirmation that the request succeeded and that printer CanonMF.axis was created. Click OK. Manage the Newly Created Printer In the left frame of the iManager, select iPrint Management | Manage Printer and specify which NDPS Printer to modify (e.g. CanonMF.axis). Click OK. To Browse for a Printer AXIS 1650 User's Manual Next to the NDPS Printer name field, click the Browse icon. Browse to your 35 Adding Printers in NetWare default container to find the newly created printer (e.g. CanonMF), select it in the Contents list and click Next. Check Printer Health Select Printer Health Monitor to check the health of the printer. Click Back to return to the Manage Printer main page. 36 AXIS 1650 User's Manual Adding Printers in NetWare Enable IPP Access In the Manage Printer main page, click the Client Support tab. To enable IPP access, check Enable IPP access, click Apply and OK. Make the Newly Created Printer Available (Optional) Using the iPrint Map Designer tool, you can quickly make the newly printer available and accessible simply by clicking on its icon in a floor plan, showing where the printers are located. The tool lets you import own floor plans as background images that can be used to drag-and-drop printers onto actual locations. These maps are then published on a Web server so users can install printers that are closest to their location. 1. Using Microsoft Explorer, start maptool.html, which can be found in \login\ippdocs\. 2. Select a map from the Background drop-down list. 3. Select a Printer icon for the newly created printer and drag it to a suitable position in the design area, i.e. the floor plan. 4. Next to the Printer List field, click the Browse icon and enter the IP address or DNS name of the server where the Print Manager is running (e.g. 171.15.115.109). 5. From the Printer List, select the printer agent you want associated with this printer icon (e.g. CanonMF). The Printer URL and Mouse Over Text will automatically be filled in with the printer agent information. Printer URL is the URL created for the printer when IPP was enabled for the printer (e.g. ipp://171.15.115.109/ipp/CanonMF). You should not need to change the URL. The Mouse over text will by default display the printer agent's name. You can override this information by entering the text you want to display when a user moves the mouse over the printer icon (e.g. CanonMF). 6. In the Printer caption field, enter the information to display (e.g. AXIS 1650 Canon MF). 7. Click Save and save the map (e.g. as AXIS1650_usb). AXIS 1650 User's Manual 37 Adding Printers in NetWare Installing the Printer Locally The printer is now accessible all over the network and will be automatically installed on any client when needed. In the HTML-page just created, double-click the new printer icon. A dialogue box will appear, waiting for confirmation: Click OK to start installation and iPrint will report progress during all stages of local installation. 38 AXIS 1650 User's Manual Adding Printers in NetWare Manual Installation of the Printer Locally In case you need to install the printer locally, use Windows' Add Printer Wizard in the usual manner: 1. Ensure that iPrint Client is installed. 2. Start | Printers and Faxes | Add a printer. 3. Select Network printer and Browse for a printer. 4. Select NDPS printers, select NDPS Controlled Access Printers. 5. Select Container (e.g. Axis) and the printer (e.g. CanonMF). 6. Wait for the printer to be installed. 7. Finally, print a test page. AXIS 1650 User's Manual 39 Print Server Management and Configuration Section 8 Print Server Management and Configuration The management and configuration tools that are supported by the AXIS 1650 allow you to: · · · · Change print server parameters Receive extended information about print jobs Receive printer port status and monitor printers Reset the AXIS 1650 Configuration Overview The method you should use to manage and configure your AXIS 1650 is dictated by your TCP/IP network. Configuration/Management methods: · · · Embedded Web Pages using a Web Browser - See page 40. FTP - See page 52. SNMP - See page 53. Print Server Management from the Embedded Web Pages All Axis print servers contain an embedded Web server that can be accessed through a Web browser. The embedded Web server provides access to configuration and management pages for the print server and the connected printer. Once you have established the AXIS 1650 in the TCP/IP environment, as described in Set the IP Address, on page 11, you can access the AXIS 1650 Web pages from any standard Web browser. The Web interface has two modes of operation: User mode and Admin mode. User Mode In User mode you can change language of the Web interface, but you have no rights to change any other parameters. This mode is intended for regular users who are only interested in using the print server's interface for checking print jobs or viewing printer properties. If you want to change any other settings, you must enter the Admin mode. See "Services Available from the User Mode" on page 42. When in Admin mode, you have access to all the print server's parameters and you can change them after your needs. This mode is intended for network administrators and can be password protected to prevent unauthorized changing of parameters. See "Services Available from the Admin Mode" on page 44. AXIS 1650 User's Manual Admin Mode 40 Print Server Management and Configuration Accessing the Web Pages Follow these steps to access the AXIS 1650 embedded Web pages: 1. Enter the print server's IP address (or host name) in the Location/Address field of your Web browser. Press Enter 2. The Printer Overview page will appear and you will be in ordinary User mode. 3. To enter Admin mode, click Admin. 4. You may be prompted for a password; in a new and unconfigured print server enter the default user name root and leave the password field empty. Click OK. root It is highly recommended that you change the default password. This is done in the Admin | General Settings | General tab => Root Password field. AXIS 1650 User's Manual 41 Print Server Management and Configuration Services Available from the User Mode The following services are available from the User mode. A click on the question mark will open the print server's help pages. Click on the Axis logotype to reach Axis' home page. Printer Overview Print Server Name The Printer Overview page shows the general parameters of the AXIS 1650 and the connected printer. This name identifies the print server to the users. The default name is AXISXXXXXX, where XXXXXX are the last six digits of the print server's serial number. This parameter shows where the print server is located, helping you to find the Canon device you are working with. Every Axis device is uniquely identified by its serial number. The serial number is found on the underside label of your print server. English and Japanese is supported in the print server's Web interface. Set language by clicking Change. By clicking the printer icon on the Printer Overview page, the Printer page opens. It shows the status and the supported capabilities of the connected printer. On some printer models, you can also print a test page from the Printer page. Note: It is only possible to print a test page on Canon printers that support printing standard ASCII characters. It is not possible to print a test page on Canon printers supporting Canon Advanced Printing Technology and Canon Advanced Raster Printing System. Underneath the printer icon is a colored symbol that indicates the status of the printer: System Location Serial Number Language Printer Page · · · green indicates that the printer is ready for printing yellow indicates warning red indicates error A dimmed printer indicates that no printer is connected to that port. Printer Status The Printer page shows status and capabilities of the printer that is connected to the selected printer port. The capabilities include Detailed Status, Manufacturer, Command Sets and Capabilities. The extent of this information depends on the printer model. Click Network Names to see a list of names that the printer is identified with in the supported network environments. Network Names 42 AXIS 1650 User's Manual Print Server Management and Configuration Print Jobs Select Print Jobs to view Printer Usage, showing the accumulated usage of the printer connected to your print server. The Printer Usage log is erased each time the print server is restarted. · · · · Printer - shows the printer model. Port - shows the port to which the printer is connected. Status - shows the status of the printer. The available status messages are ready, busy and off-line. Printed Pages - shows the number of pages that the printer has printed (not shown for all printer models). View Job Log Presents the 32 latest print jobs as Document Name, Owner, Page Count, Time and Print Results. Note that the time when the document was printed is only available if the print server has access to a time server. Shows the time elapsed since last time the print server was restarted. Shown for multifunctional Canon devices with scanning capabilities. If the scanner is in use, its status will change from Idle to Busy and the User name will be shown. Print Server Uptime Scanner Help The Help pages present basic information about the AXIS 1650 and its Web user interface. AXIS 1650 User's Manual 43 Print Server Management and Configuration Services Available from the Admin Mode Click on the Axis logotype to reach Axis' home page. A click on the question mark will open the print server's help pages. The following services are available from the Admin mode. This Print Server This page contains a section that allows you to view and modify the general parameter settings of the AXIS 1650. Management operations, like restarting the AXIS 1650 and resetting its parameters to their default settings are also available. This name identifies the print server to the users. The default name is AXISXXXXXX, where XXXXXX are the last six digits of the print server's serial number. This parameter shows where the print server is located, helping you to find the Canon device you are working with. Every Axis device is uniquely identified by its serial number. The serial number is found on the underside label of your print server. See "Print Server Installation" on page 10. In this section, you manage the print server's general settings as well as permissions. To change the print server's general parameters, select Admin | General Settings => Change. For additional information, see "Setting General Parameters" on page 47. To change print server permissions and restrictions, select Admin | General Settings => Change and select the Restrictions tab. For additional information, see "Setting Restrictions" on page 48. Parameter List Restart Print Server Name System Location Serial Number General Settings Click Detailed View to see all parameters and their current settings. Restarts the print server. When the power LED lights constantly and the Network indicator starts flashing to indicate network activity, the print server is ready for use again. New configuration settings will then become active. All contact with the printer server will be lost during a restart. A Software Default will reset all print server parameters to their factory default settings except: · · · Node address (NODE_ADDR.) IP address (IP_ADDR.) DHCP enabled or disabled (DHCP_ENABLE.) Software Default A Software Default differs from a Factory Default. A Factory Default is performed by pressing the Test button, located on the print server, in a specific sequence. See "The Test Button" on page 61. When the power LED lights constantly and the Network indicator starts flashing to indicate network activity, the print server is ready for use again. 44 AXIS 1650 User's Manual Print Server Management and Configuration Printer Page By clicking the printer icon on the This Print Server page, a Printer page opens, allowing you to view the status and the supported capabilities of the connected printer. On some printer models, you can also print a test page from the Printer page. Note: It is only possible to print a test page on Canon printers that support printing standard ASCII characters. It is not possible to print a test page on Canon printers supporting Canon Advanced Printing Technology and Canon Advanced Raster Printing System. Underneath the printer icon is a colored symbol that indicates the status of the printer: · · · A Printer Status green indicates that the printer is ready for printing yellow indicates warning red indicates error dimmed printer indicates that no printer is connected to that port. The printer page shows status and capabilities of the printer that is connected to the selected printer port. The capabilities include Detailed Status, Manufacturer, Command Sets and Capabilities. The extent of this information depends on the printer model. Click Network Names to see a list of names that the printer is identified with in the supported network environments. Network Names Print Jobs Select Print Jobs to view Printer Usage, showing the accumulated usage of the printer connected to your print server. The Printer Usage log is erased each time the print server is restarted. · · · · Printer - shows the printer model. Port - shows the port to which the printer is connected. Status - shows the status of the printer. The available status messages are ready, busy and off-line. Printed Pages - shows the number of pages that the printer has printed (not shown for all printer models). View Job Log Presents the 32 latest print jobs as Document Name, Owner, Page Count, Time and Print Results. The time when the document was printed is only available if the print server has access to a time server. Shows the time elapsed since last time the print server was restarted. Shown for multifunctional Canon devices which have scanning capabilities. If the scanner is in use, the status will change from Idle to Busy and the User name will be shown. Print Server Uptime Scanner AXIS 1650 User's Manual 45 Print Server Management and Configuration Network Settings From the Network Settings page you can set all parameters that control the network traffic to and from the AXIS 1650. You can enable or disable any of the supported network protocols and fine-tune the parameters. To change the print server's network settings, select Admin | Network Settings | Detailed View. For additional information, see "Setting Network Protocol Parameters" on page 49. Changing Network Settings Support From the Support page you can receive help to resolve any installation or print problems that might occur. If your problems persist, the Support page allows you to produce a Server Report. The Server Report includes the settings of the AXIS 1650, information about your connected printer as well as the current network settings. The Server Report is of great value for support assistance, so please mail, email or fax it to your support channel together with a detailed problem description. If you cannot successfully install your print server, please try the troubleshooting instructions to solve your installation problems. The troubleshooter is started by clicking the Troubleshooting steps link. If you still cannot print satisfactorily after performing the troubleshooting instructions, please produce a Server Report and contact your local supplier. A Server Report is a document containing technical information about your print server and the connected printer. This report is of great value for support assistance, so please produce a Server Report and mail, email or fax it to your support channel together with a detailed problem description. Click the Server Report link to prepare your Server Report and problem description to Axis Communications Support team: You must have an e-mail account and an e-mail program set up on your computer. It is also important that you include the entire Web page in the mail and not just a link to the page. Click the print server product page to receive information about your print server model. The product page, available on the Axis Web Site, offers you up-to-date information, print server manuals, FAQs, software updates and technical support, etc. If you need to contact any Axis distributor or local office, please click the Axis distributor or office link. Troubleshoot and Upgrade Server Report AXIS Online Services Contact Information Statistics The Statistics page displays information about the network traffic to and from the AXIS 1650 as well as information about servers and services that are connected or associated with the AXIS 1650. Click the Network Statistics icon to display a list of statistical information about the data traffic to and from the print server. Click the Network Connections icon to display a list of servers and network services that currently are connected to the print server and the status of each connection. AXIS 1650 User's Manual Network Statistics Network Connections 46 Print Server Management and Configuration Setting General Parameters To change the print server's general parameters, select Admin | General Settings => Change in the Web interface. Note: All print server settings have default values that have been carefully selected by Axis. In most instances, there is no need to change the default values. Observe that all network configuration should involve the Network Administrator. Print Server Name This name identifies the print server to the users and will be part of the default name of the connected printer and printer queue name. The default name is AXISXXXXXX, where XXXXXX are the last six digits of the print server serial number. Example: If the serial number is 00 40 8c 18 16 36, the default print server name is AXIS181636. This name identifies the network printer to the users. Default = This parameter allows you to specify where the network printer is located in your organization. This enables you to find the device you are working with. Default = Enter the name of e.g. the System Manager. Default = Enter the telephone number of e.g. the System Manager. Default = Enter comments regarding the network printer. Default = Select the language to be displayed in the print server's embedded Web pages: English or Japanese. Enter a password in the field. Up to 15 alphanumeric characters can be entered. Default = Set your network speed: 10_HALF_DX, 10_FULL_DX, 100_HALF_DX, 100_FULL_DX or let the print server sense the correct speed (AUTO_SENSE). Default = AUTO_SENSE Select Yes to permit access using the SNMP protocol, select No to reject access using the SNMP protocol. Default = Yes Specify the community name for SNMP. Up to 32 alphanumeric characters can be entered. Default = public System Name System Location System Contact System Contact Phone Nbr. System Comment Language Root Password Network Speed SNMP Enabled Community Name AXIS 1650 User's Manual 47 Print Server Management and Configuration Setting Restrictions To change print server permissions and restrictions, select Admin | General Settings => Change and select the Restrictions tab in the Web interface. TCP Restriction Enabled When set to Yes, users specified in the IP Address List are rejected or accepted (depending on how the TCP Restriction Mode is set), to send print jobs over the print server. Default = No When set to Accept, users specified in the TCP Restriction IP Address List are allowed to use this print server. When set to Reject, users specified in the TCP Restriction IP Address List are not allowed to use this print server. Default = Accept Here you specify the users which are allowed (or not allowed, depending on how TCP Restriction Mode is set) to use the print server. IP addresses or ranges of IP addresses can be specified: Example IP addresses: 10.13.16.150, 10.13.16.151 Example IP address range: 10.13.16.160-0.13.16.170 Default = Note: If your print server is connected to a CAPT 1.0 printer you will receive an error message stating Network Error if you are not allowed to print with this print server TCP Restriction Mode TCP Restriction IP Address List SNMP Restriction Enabled When set to Yes, users specified in the SNMP Restriction IP Address List are rejected or accepted (depending on how the SNMP Restriction mode is set). Default = No When set to Accept, only users specified in the SNMP Restriction IP Address List are permitted to specify/browse the settings for the device using the SNMP protocol. When set to Reject, only users specified in the SNMP Restriction IP Address List are rejected from specifying/browsing the settings for the device using the SNMP protocol. Default = Accept Users specified here are rejected or accepted. IP addresses or ranges of IP addresses can be specified as follows: Example IP addresses: 10.13.16.150, 10.13.16.151 Example IP address range: 10.13.16.160-10.13.16.170 Default = When set to Yes, users specified in SLP Restriction IP Address List are rejected or accepted (depending on how the SLP Restriction Mode is set). Default = No When set to Accept, only users specified in the SLP Restriction IP Address List are permitted to specify/browse the settings for the device using the SLP protocol. When set to Reject, only users specified in the SLP Restriction IP Address List are rejected from specifying/browsing the settings for the device AXIS 1650 User's Manual SNMP Restriction Mode SNMP Restriction IP Address List SLP Restriction Enabled SLP Restriction Mode 48 Print Server Management and Configuration using the SLP protocol. Default = Accept SLP Restriction IP Address List Users specified here are rejected or accepted.IP addresses or ranges of IP addresses can be specified as follows: Example IP addresses: 10.13.16.150, 10.13.16.151 Example IP address range: 10.13.16.160-10.13.16.170 Default = Setting Network Protocol Parameters To change the print server's network settings, select Admin | Network Settings | Detailed View in the Web interface. Frame Type LPD Banner Page Mode AXIS 1650 uses frame type Ethernet II for network packages. Check the appropriate box to specify if the LPD banner page is to be printed. Off disables the LPD banner page. Auto prints the LPD banner page first or last depending on your operating system. Last forces the printer to print the LPD banner page last, independently of operating system. Default value = Off Note: LPD Banner Page Mode is not available for Canon printers supporting Canon Advanced Printing Technology or Canon Advanced Raster Printing System. IP Address Specify the IP address of your print server in the format w.x.y.z. You should acquire a unique and unused IP address from your Network Administrator in order to prevent conflicts with other network devices. Default value = 192.168.0.90 Note: If DHCP, BOOTP or RARP is enabled, your manual settings might be overridden when you restart the print server. To make sure that this will not happen, you are advised to disable BOOTP and RARP when you are setting the IP address manually, DHCP is disabled by default. Important: If you change the IP address you will lose contact with the print server. You must enter the new IP address of the print server in the address/location field of your Web browser to continue to configure and manage the print server via the Web browser.