User manual AXIS 216FD

AXIS 216FD Fixed Dome Network Camera User's Manual About this Document This manual is intended for administrators and users of the AXIS 216FD Network Camera, and is applicable for software release 4.34 and later. It includes instructions for using and managing the AXIS 216FD on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be beneficial, for developing shell scripts and applications. Later versions of this document will be posted to the Axis Website, as required. See also the product's online help, available via the Web-based interface. Canada - This Class B digital apparatus complies with Canadian ICES-003. Europe - This digital equipment fulfills the requirements for radiated emission according to limit B of EN55022/1998, and the requirements for immunity according to EN55024/1998 residential, commercial, and light industry. Japan - This is a class B product based on the standard of the Safety Notices Used In This Manual Caution! - Indicates a potential hazard that can damage the product. Important! - Indicates a hazard that can seriously impair operation. Do not proceed beyond any of the above notices until you have fully understood the implications. Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Australia - This electronic device meets the requirements of the Radio communications (Electromagnetic Compatibility) Standard AS/NZS CISPR22:2002. Equipment Modifications This equipment must be installed and used in strict accordance with the instructions given in the user documentation. This equipment contains no user-serviceable components. Unauthorized equipment changes or modifications will invalidate all applicable regulatory certifications and approvals. Intellectual Property Rights Axis AB has intellectual property rights relating to technology embodied in the product described in this document. In particular, and without limitation, these intellectual property rights may include one or more of the patents listed at http://www.axis.com/patent.htm and one or more additional patents or pending patent applications in the US and other countries. Liability Every care has been taken in the preparation of this manual. Please inform your local Axis office of any inaccuracies or omissions. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. Axis Communications AB makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material. This product contains licensed third-party software. See the menu item "About" in the product's user interface for more information. This product contains source code copyright Apple Computer, Inc., under the terms of Apple Public Source License 2.0 (see http://www.opensource.apple.com/apsl/). The source code is available from: http://developer.apple.com/darwin/projects/bonjour/ Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) MPEG-4 decoder license. To purchase further licenses, contact your reseller. Trademark Acknowledgments Apple, Boa, Bonjour, Ethernet, Internet Explorer, Linux, Microsoft, Mozilla, Netscape Navigator, OS/2, Real, QuickTime, UNIX, Windows, WWW are registered trademarks of the respective holders. Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. Axis Communications AB is independent of Sun Microsystems Inc. UPnPTM is a certification mark of the UPnPTM Implementers Corporation. Electromagnetic Compatibility (EMC) This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Re-orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a different circuit to the receiver. Consult your dealer or an experienced radio/TV technician for help. Shielded (STP) network cables must be used with this unit to ensure compliance with EMC standards. This product includes MPEG-4 AAC audio coding technology licensed by Fraunhofer IIS. Refer to FHG audio home page http://www.iis.fraunhofer.de/amm/ USA - This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference. AXIS COMMUNICATIONS Quick User's Guide Support Should you require any technical assistance, please contact your Axis reseller. If your questions cannot be answered immediately, your reseller will forward your queries through the appropriate channels to ensure a rapid response. If you are connected to the Internet, you can: · download user documentation and firmware updates · find answers to resolved problems in the FAQ database. Search by product, category, or phrases · report problems to Axis support by logging in to your private support area · visit Axis Support at www.axis.com/techsup/ Safety Notice - Battery Replacement The AXIS 216FD uses a 3.0V CR2032 Lithium battery as the power supply for its internal real-time clock (RTC). Under normal conditions this battery will last for a minimum of 5 years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. A log message will appear when the battery needs replacing. The battery should not be replaced unless required! If the battery does need replacing, please observe the following: · Danger of Explosion if battery is incorrectly replaced · Replace only with the same or equivalent battery, as recommended by the manufacturer. · Dispose of used batteries according to the manufacturer's instructions. WEEE Directive The European Union has enacted a Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE Directive). This directive is applicable in the European Union member states. The WEEE marking on this product (see right) or its documentation indicates that the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area. Business users should contact the product supplier for information on how to dispose of this product correctly. This product should not be mixed with other commercial waste. AXIS 216FD User's Manual Rev.1.0 Part No: 26031 February 2006 Copyright© Axis Communications AB, 2006 4 AXIS 216FD Contents Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Accessing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Access from a browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Setting the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Accessing the camera from the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 The Live View Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Video Streams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 How to stream MPEG-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 MPEG-4 clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Motion JPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Accessing the Setup tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 AXIS Media Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Video and Image settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Live View Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 HTML Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 External Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Sequence Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Event Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Event Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Configuring Event Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Port Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Network - Basic TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Network - Advanced TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SMTP (email) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 UPnPTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 RTP / MPEG-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Ports & Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 LED Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 AXIS 216FD Resetting to the Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 The I/O Terminal Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Pinout and Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5 6 AXIS 216FD - Product Features Product Features AXIS 216FD Fixed Dome Network Camera is a high-performance, progressive-scan camera for professional surveillance. Its discreet, compact casing effectively protects against tampering. Two-way audio support enables communication with visitors or intruders. Multi-window motion detection and simultaneous Motion JPEG and MPEG-4 allow for optimization both on image quality and bandwidth efficiency. Up to 30 fps in VGA. Multi-level password protection, IP-address filtering and HTTPS encryption ensures network security. Power over Ethernet reduces cabling and enables centralized power back up. Supported by the industry's largest base of surveillance applications, this camera constitutes the perfect solution for securing e.g. stores, schools and offices. For indoor use only Key features · · · · · · Discreet and compact design, effectively protecting against tampering Superior image quality with progressive scan and 30 frames per second in VGA Simultaneous Motion JPEG and MPEG-4 for optimized quality and bandwidth Two-way audio support including built-in microphone Power over Ethernet for reduced cabling and consolidated power Multi-window motion detection with alarm image buffering AXIS 216FD - Product Features 7 Overview Status indicator (LED) Camera unit Dome casing Microphone Control button Power connector Cover plates Audio out Audio in Power indicator (LED) Network connector and PoE Serial number (S/N) The serial number is required during the installation. Please make a note of the serial number and retain for future reference. Network indicator (LED) I/O terminal connector Microphone - Built-in microphone for one way audio. To prevent unauthorized listening, the internal microphone can be disabled by inserting a plug in the 'Audio in' connector. Power Connector - For connection of the PS-H power adapter (included). I/O Connector - The I/O terminal connector provides the physical interface to one transistor output, one digital input and an auxiliary connection point for DC power. For more information, see The I/O Terminal Connector, on page 42. Network Connector - The camera connects to the network via a standard network connector. Supporting NWAY, the camera detects the speed of the local network segment (10BaseT/100BaseTX Ethernet). Supporting PoE (Power over Ethernet), the camera can be powered directly from the network cabling. 8 AXIS 216FD - Product Features Audio out- Audio output (line level), which can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo connector must be used for the audio out. Audio in - One 3.5mm input for a mono microphone, or for line-in mono signal (left channel is used from a stereo signal). Serial Number Label - The serial number may be required during installation. Control Button - Press this button to install using the AXIS Internet Dynamic DNS Service, or to restore the factory default settings, as described in Resetting to the Factory Default Settings, on page 41. I/O terminal connector: Pin 4 Function Transistor Output Description With a maximum load of 50mA and a maximum voltage of 24V DC, this output has an open-collector NPN transistor with the emitter connected to the GND pin. If used with an external relay, a diode must be connected in parallel with the load, for protection against voltage transients. Connect to GND to activate, or leave floating (or unconnected) to deactivate. Can be used to power auxiliary equipment, max 50mA. 3 2 1 Digital Input 3.3V DC GND LED indicators: LED Network Color Green Amber Unlit Green Description Steady for connection to 100 Mbit/s network. Flashes for network activity. Steady for connection to 10 Mbit/s network. Flashes for network activity. No connection. Shows steady green for normal operation. Note: The Status LED can be configured to be unlit during normal operation, or to flash only when the camera is accessed. See the online help files for more information. Go to Setup > System Options > LED settings Steady during startup, reset to factory default or when restoring settings. Slow flash for failed upgrade. Normal operation. Flashes green/amber during firmware upgrade. Status Power Amber Red Green Amber AXIS 216FD - Accessing the Camera 9 Accessing the Camera Before accessing the camera it must be installed. Please see the installation guide supplied with your product. The camera can be used with most standard operating systems and browsers. The recommended browser is Microsoft Internet Explorer with Windows, Safari with Macintosh and Mozilla with other operating systems. Notes: · To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX controls and allow the AXIS Media Control (AMC) to be installed on your workstation. · QuickTimeTM and Real PlayerTM are also supported for viewing streaming MPEG-4 video and audio. · If your workstation restricts the use of additional software components, the camera can be configured to use a Java applet for viewing motion JPEG. · The AXIS 216FD includes one (1) decoder license for viewing MPEG-4 video streams. This is automatically installed with AMC. The administrator can disable the installation of the MPEG-4 decoder, to prevent unlicensed copies being installed. Access from a browser 1. Start a browser (e.g. Internet Explorer, Mozilla) 2. Enter the IP address or host name of the camera in the Location/Address field of your browser. To access the camera from a Macintosh computer (Mac OSX), simply click on the Bonjour tab and select the AXIS 216FD from the drop-down list. 3. If this is the first time the camera is accessed, see Setting the Password, on page 10. Otherwise enter your user name and password, as set by the administrator. 4. The camera's Live View page is now displayed in your browser. Note: The layout of the Live View page may have been customized to specific requirements. Consequently, some of the examples and functions featured here may differ from those displayed on your own Live View page. 10 AXIS 216FD - Accessing the Camera Setting the Password 1. When accessing the camera for the first time, the `Configure Root Password' dialog will be displayed on the screen. 2. Enter a password and then re-enter it, to confirm the spelling. Click OK. 3. The `Enter Network Password' dialog will appear. Enter the User name: root Note: The default administrator user name root is permanent and cannot be deleted. 4. Enter the password as set in step 2 above, and click OK. If the password is lost, the camera must be reset to the factory default settings. See page 41. 5. If required, click Yes to install the AXIS Media Control (AMC). You will need administrator rights on the computer to do this. Accessing the camera from the Internet Once installed, the camera is accessible on your local network (LAN). To access the camera from the Internet you must configure your broadband router to allow incoming data traffic to the camera. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the camera. This is enabled from Setup > System Options > Network > TCP/IP Advanced. For more information, please see NAT traversal (port mapping), on page 36. See also the AXIS Internet Dynamic DNS Service at www.axiscam.net or, for Technical notes on this and other topics, visit the Axis Support Web at www.axis.com/techsup AXIS 216FD - Accessing the Camera 11 Adjusting the image Image balance ring Tilt adjustment screw Focus puller Zoom puller Tilt adjustment screw Locking screw 1. Open the Live View page in the Web interface and make the following adjustments on the camera: 2. Loosen the locking screw and tilt adjustment screws. 3. Turn the lens to the desired position. 4. Once satisfied, gently tighten the locking screw and tilt adjustment screws to secure the camera's position. 5. Turn the image balance ring to set the horizontal position. 6. Open the Focus Adjustment page in the Web interface under Basic Configuration > Focus and follow the on-screen instructions. Use the image window to adjust the focus and zoom. · To set the focus and zoom, loosen the zoom and focus pullers counterclockwise and rotate the rings. · Lock the focus and zoom pullers in position by rotating the screws clockwise. 12 AXIS 216FD - Accessing the Camera The Live View Page Depending on whether or not the Live View page has been customized, the buttons described below may or may not be visible. To resize the video image, click the View Size buttons: half-size (x1/2), full-size (x1), x2 or x4. Note that this does not change the video image's resolution, but simply how it is displayed. The Video Format drop-down list allows the video format on the Live View page to be temporarily changed. The Output buttons control the output directly from the Live View page. These buttons are configured under Setup > Live View Config > Layout. Pulse - click this button to activate the output for a defined period of time, e.g. to switch on a light for 20 seconds. Active/Inactive - click these buttons to manually start and stop a connected device, e.g. switch a light on/off. The Action buttons can trigger an event directly from the Live View page. These are configured under Setup > Live View Config > Layout. The Snapshot button saves a snapshot of the video image currently being displayed. Right-click on the video image to save it in JPEG format on your computer. This button is primarily intended for use when the AMC viewer toolbar is not available. The AMC viewer toolbar (AXIS Media Control) is available in Microsoft Internet Explorer only. It displays the following buttons: The Play/Stop button starts and stops the live video stream. The Snapshot button saves a snapshot of the video image currently being displayed. The Snapshot function and the target directory for saving snapshots can be configured from the AMC Control Applet in the Windows Control Panel (Internet Explorer only). Click the View Full Screen button to make the video image fill the entire screen area. No other windows will be visible. Press Esc (Escape) on the computer keyboard to exit full screen. AXIS 216FD - Accessing the Camera AMC audio controls There are audio controls for controlling the client computer's speaker output. These controls are only available when audio is enabled, see AXIS Media Control, on page 17 and Audio, on page 21. Click the Speaker and Microphone buttons to switch the sound off and on for the speaker and microphone, respectively. 13 Use the sliders to control the volume on the speaker and microphone. The volume can be set between 0 and 100. The Buffer slider controls the size of the buffer for audio. A higher level will reduce audio break-up, but may introduce a noticeable lag in audio transmission. There are four settings i.e. min, low, high and max. When using Half-duplex mode, this button toggles between allowing you to speak and listen. The first icon indicates that you can talk and the speaker attached to the camera will play your voice. The second indicates that you will hear audio from the camera, but no audio will be sent to any web clients. When in simplex talk mode, the icon toggles between allowing you to speak and is dimmed when you do not want other clients to receive any audio. 14 AXIS 216FD - Video Streams Video Streams The AXIS 216FD provides several different image and video stream formats. The type to use depends on your requirements and on the properties of your network. The Live View page in the AXIS 216FD provides access to MPEG-4 and Motion JPEG video streams, as well as to single JPEG images. Other applications and clients can also access these video streams/images directly, without going via the Live View page. How to stream MPEG-4 This video compression standard makes good use of bandwidth, and can provide DVD-quality video streams at less than 1 Mbit/s. Note that the image settings of the MPEG-4 stream are the same for all clients. Deciding on the combination of protocols and methods to use depends on your viewing requirements, and on the properties of your network. The available options in AMC are: Unicast RTP This unicast method (RTP over UDP) should be your first consideration for live video, especially when it is important to always have an up-to-date video stream, even if some images are dropped. This unicast method (RTP tunneled over RTSP) is useful as it is relatively simple to configure firewalls to allow RTSP traffic. This unicast method can be used to traverse firewalls. Firewalls are commonly configured to allow the HTTP protocol, thus allowing RTP to be tunneled. This method (RTP over TCP) should be your first consideration for live video, especially when it is important to always have an up-to-date video stream, even if some images are dropped. RTP over RTSP RTP over RTSP over HTTP Unicasting is used for video-on-demand broadcasting, so that there is no video traffic on the network until a client connects and requests the stream. Note: There is a maximum of 20 simultaneous viewers. Multicast RTP Multicasting provides the most efficient usage of bandwidth, especially when there are large numbers of clients viewing simultaneously. Note however, that a multicast broadcast cannot pass a network router unless the router is configured to allow this. It is thus not possible to multicast over e.g. the Internet. AMC will negotiate with the camera to determine exactly which transport protocol to use in the order listed above. This order can be changed and the options disabled, to suit any specific requirements. Important! MPEG-4 is licensed technology. The AXIS 216FD includes one viewing client license. Installing additional unlicensed copies of the viewing client is prohibited. To purchase additional licenses, contact your Axis reseller. AXIS 216FD - Video Streams 15 MPEG-4 clients AXIS Media Control (AMC) The recommended method of accessing live video (MPEG-4 and Motion JPEG) from the AXIS 216FD is to use the AXIS Media Control (AMC) in Microsoft Internet Explorer in Windows. The AMC control panel can be used to configure various video and audio settings. Please see the readme file included in the tool for more information. The AMC control panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: · Windows Control Panel (from the Start menu) · Alternatively, right-click the video image in Internet Explorer and click Settings in the menu. QuickTimeTM & Real PlayerTM To access the video stream from e.g. QuickTimeTM or Real PlayerTM the following paths can be used: · rtsp:///mpeg4/media.amp · rtsp:///mpeg4/media.3gp Notes: · The AXIS 216FD supports QuickTime 6.5.1 (or later) and Real Player 10.5 (or later) · QuickTime adds latency to the video and audio stream (up to 3 seconds) · It may be possible to use other players to view the MPEG-4 stream using the paths above, although this is not guaranteed by Axis · = IP address Motion JPEG This format uses standard JPEG still images for the video stream. These images are then displayed and updated at a rate sufficient to create a stream that shows constantly updated motion. The Motion JPEG stream uses considerable amounts of bandwidth, but provides excellent image quality and access to each and every individual image contained in the stream. The recommended method of accessing Motion JPEG live video from the AXIS 216FD is to use the AXIS Media Control (AMC) in Microsoft Internet Explorer in Windows. Note also that multiple clients accessing Motion JPEG streams can use different image settings. 16 AXIS 216FD - Video Streams Alternative methods of accessing the video stream Video/images from the AXIS 216FD can also be accessed in the following ways: · Motion JPEG server push (if supported by the client, e.g. Mozilla/Firefox). This option maintains an open HTTP connection to the browser and sends data as and when required, for as long as required. See HTML Examples, on page 27. · Still JPEG images in a browser. Enter e.g. the path: http:///axis-cgi/jpg/image.cgi?resolution=320x240 · Windows Media Player. This requires AMC and the MPEG-4 viewing client to be installed. The paths that can be used are listed below in the order of preference. · Unicast via RTP: axrtpu:///mpeg4/media.amp · Unicast via RTSP: axrtsp:///mpeg4/media.amp · Unicast via RTSP, tunneled via HTTP: axrtsphttp:///mpeg4/media.amp · Multicast: axrtpm:///mpeg4/media.amp Note: = IP address AXIS 216FD - Configuration 17 Configuration This section describes how to configure the camera, and is intended for product Administrators, who have unrestricted access to all the Setup tools, and Operators, who have access to the settings for Video & Image, Audio, Live View Config and Event Configuration. The camera is configured from Setup, from a standard browser (see Minimum web browsing requirements, on page 50). The descriptions below show examples of the features available in the AXIS 216FD. For details of each setting, please refer to the online help available from the setup tools. Click to access the online help. Accessing the Setup tools Follow the instructions below to access the Setup Tools from a browser. 1. Start your browser and enter the IP address or host name of the camera in the location/address field. 2. The Live View page is now displayed. Click Setup to display the Setup tools. Setup tools AXIS Media Control The AXIS Media Control (AMC) is installed automatically the first time the camera is accessed from Microsoft Internet Explorer. The AMC control panel can be opened by right-clicking on the video image in the Live View web page. The AMC control panel can be used to configure various video and audio settings. Please see the readme file included in the tool for more information. 18 AXIS 216FD - Configuration Video and Image settings Image Appearance Use these settings to change the image as required. The video image can be rotated and fine-tuned by adjusting the color level, the brightness and the sharpness. The configuration of the video image will affect the camera's overall performance, depending on how it is used and on the available bandwidth. Setting higher resolution and lower compression improves video image quality, but increases the amount of bandwidth used. Please see the online help for further information on these settings. AXIS 216FD - Configuration 19 Text Overlay Settings Use these settings to include a text, date and time overlay. The text, date and time overlay is included on one line at the top or bottom of the video image. Text, date and time overlay Video Stream Define the maximum video stream time per session in seconds, minutes or hours. When the set time has expired, a new stream can be started by refreshing the page in the browser. For unlimited video stream time, select the Unlimited radio button. Note that the maximum video stream time does not apply to clients connecting via multicast. The frame rate allowed to each viewer can also be limited, to avoid bandwidth problems on the network. To allow the highest available frame rate, select the Unlimited radio button. For a preview of the image before saving, click Test. When satisfied with the settings, click Save. Please note that the preview image will be in JPEG format, even though the settings are valid both for Motion JPEG and MPEG-4. Overlay/Mask The following options are available for overlays and masks: · Uploaded image as overlay · Configurable areas as privacy mask Uploaded image as overlay is a text and/or a static image superimposed over the video image, for extra information. Configurable areas as privacy mask are configurable areas of solid color that can be used to block out certain parts of the video image. Advanced - Camera Settings These pages include different settings for fine-tuning the video image. To compensate for the lighting conditions, the white balance and exposure control can be adjusted. DC-Iris should always be set to Enabled, except during focusing. DC-Iris is a varifocal lens which automatically regulates the amount of light entering the camera. 20 AXIS 216FD - Configuration Low Light Behavior Exposure priority defines the balance between image quality and the frame rate. Higher image quality may reduce frame rate and increase motion blur. A prioritized frame rate may instead increased image noise. Depending on requirements, use this to give higher priority to the image quality or to the frame rate. Please refer to the online help for more information . Advanced - MPEG-4 Settings GOV Settings The GOV structure describes the composition of the MPEG-4 video stream. Setting the GOV-length to a high value saves considerably on bandwidth. The Cyclic refresh parameter gives a smoother bit rate and can be useful if bandwidth is limited. Bit Rate Control Limiting the maximum bit rate is a good way of controlling the bandwidth used by the MPEG-4 video stream. Leaving the Maximum bit rate as unlimited will provide consistently good image quality, but at the expense of increased bandwith usage whenever there is more activity in the image. Limiting the bit rate to a defined value will prevent excessive bandwidth usage, but images will be lost when the limit is exceeded. Note that a maximum bit rate can be used for both variable and constant bit rates. The bit rate type can be set as Variable Bit Rate (VBR) or Constant Bit Rate (CBR). VBR will adjust the bit rate according to the images' complexity, thus using a lot of bandwidth for a lot of activity in the image and less for lower activity in the monitored area. CBR allows you to set a fixed Target bit rate that will consume a predictable amount of bandwidth, and which will not change whatever happens in the image. As the bit rate would usually need to increase for increased image activity, but in this case cannot, the frame rate and image quality will be affected negatively. To go some of the way towards compensating for this, it is possible to prioritize either the frame rate or the image quality whenever the bit rate would normally need to be increased. Not setting a priority means the frame rate and image quality will be affected approximately equally. AXIS 216FD - Audio 21 Audio The AXIS 216FD can transmit audio to other clients using either the built-in microphone or a connected external microphone and can play audio received from other clients via a connected speaker. Note: The speaker connected to the audio output must have a built-in amplifier, e.g. PC speakers. Client PC Internal microphone TCP/IP Network Internal microphone An example of a network using AXIS 216FD cameras to transmit audio and video across the network. Audio Settings This section describes how to configure the basic audio settings for the AXIS 216FD, e.g. set the communication mode and adjust the sound levels in the microphone and speaker connected to the camera. Enable Audio Check this box to enable audio in the AXIS 216FD. 22 AXIS 216FD - Audio Audio Channels Audio mode Half-duplex mode transmits and receives audio in both directions, but only in one direction at a time. This means that you must select when to receive or transmit audio with the push-to-talk button. To speak, press and hold the button (check that the microphone is not muted). When finished speaking, release the button and you will receive audio from the other end of the connection. Note that the push-to-talk button is configured from AMC, see AXIS Media Control, on page 17. It is also possible to configure the push-to-talk button so that it toggles between speaking and listening modes. When selecting Simplex - Network Camera speaker only mode, the speaker connected to the camera will play audio, but no audio will be transmitted from the camera to other web clients. This could be used to e.g. provide spoken instructions to a person seen in the camera. This mode requires you to use the push-to-talk button. Simplex - Network Camera microphone only mode transmits audio only from the AXIS 216FD to web clients. It will not receive audio from any other web clients. This can be used in remote monitoring, web attractions etc., to provide live audio, as well as video, of a monitored situation. When using half-duplex, the Send the sound from the active client to all other clients option transmits the audio signal from the client that is talking to all the other clients. Audio Input Audio from an external microphone or a line source can be connected to the Audio in connector of the AXIS 216FD. The audio source must be set to Microphone or Line depending on the connected device. Note: To prevent unauthorized listening, the internal microphone can be disabled by inserting a plug in the Audio in connector. The Enable microphone power option provides DC power for an external microphone. If using a small electret condenser microphone such as a clip-on mic or a PC microphone, this option needs to be enabled. Note: To use a high impedance dynamic microphone, DC power should not be enabled. DC power will not harm the microphone, but if you are uncertain, try switching it off and on. The default value is DC power enabled. To use a professional microphone requiring 48V phantom power, you need an external power supply and must use a balanced-unbalanced converter (audio transformer) in between. If there are problems with the sound input being too low or high, adjust the input gain for the microphone attached to the AXIS 216FD. Select the desired audio Encoding format, AAC, G711, G726. AXIS 216FD - Audio Depending on the selected encoding, set the desired audio quality (Bit rate). The settings depend on the available bandwidth and the required audio quality. The AXIS 216FD can be set to trigger an event if the incoming sound level rises above, falls below or passes the set value. The Alarm level is set between 0-100%. 23 Audio Output If the sound from the speaker is too low or high, adjust the output gain for the active speaker attached to the AXIS 216FD. When satisfied with the settings, click Save, or click Reset to revert to the previously saved settings. Note: To receive synchronized video and audio, it is recommended that the time settings in the camera and client PC are synchronized with an NTP Server. This is enabled in the camera under System Options > Date & Time. Please refer to the help pages for more information. 24 AXIS 216FD - Live View Config Live View Config Layout These are the tools for deciding the layout of the Live View page. The layout can be set in 3 ways: · Use Axis look - the layout is unchanged. · Use custom settings - modify the Axis look, with your own colors, images etc. Click the Configure button and see Customizing the default page, on page 25. · Own Home Page - Upload and use your own custom page as the default web page. Click the Configure button and see Customizing the default page, on page 25. The other settings on this page concern which features to include, e.g. action button, output button, default video stream and viewer. See page 26 for more information. AXIS 216FD - Live View Config 25 Customizing the default page The appearance of the default Live View page can be customized to suit your own requirements, or you can upload and use your own home page. To upload your own files, click the Upload/Remove button and see the description below. Upload Own Web Files Your own web files, background pictures, etc., must first be uploaded to the camera in order to be available for selection in the Custom Settings setup dialog. Once uploaded, the files are shown in the drop-down lists. 1. Click the Upload/Remove button. 2. Enter the path to the file, e.g. a file located on your workstation or click the Browse button. 3. Select the user level for the uploaded file. Setting the user access level means that you have complete control over which pages can be viewed by which users. 4. When the path is shown correctly in the text field, click the Upload button. All uploaded files are shown in the list in the lower section of the page. To remove a file, check the box provided next to it and then click the Remove button. Unchecking the box for Show setup link will remove the setup link from the product's Home Page. The Setup Tools will then only be accessible by entering the full setup address into the address/URL field of a browser. If the setup link is hidden, setup can be reached at this url: http:///operator/basic.shtml. Own Home Page To use a previously uploaded web page as the default page, check the box, select the page from the drop-down list and click OK. 26 AXIS 216FD - Live View Config Action Buttons The manual trigger buttons can be used to manually trigger and stop an event from the Live View page. See Event Configuration, on page 28. Enabling the display of the Snapshot button allows users to save a snapshot from the video stream by clicking the button. This button is mainly intended for use with browsers other than Internet Explorer, or when otherwise not using AXIS Media Control (AMC) to view the video stream. AMC (an ActiveX control) for Internet Explorer provides its own snapshot button. Output Buttons The output buttons are used to manually activate the output from the Live View page, e.g. to switch a light on and off. There are 2 options for how the output is activated: · The Pulse button activates the output for a defined period · Active/Inactive displays 2 buttons, one for each action (on/off) Default Video Format Select the default video format to use on the Live View page. Checking the box for Show video format selection displays a drop-down list on the Live View page allowing you to temporarily change the format. When using MPEG-4 as the video format, the default viewer is AXIS Media Control with Internet Explorer. Note: It is also possible to view Motion JPEG when MPEG-4 is chosen as default and vice versa. Default Viewer From the drop-down lists, select the default method for viewing video images for your browser. The camera will attempt to show the video images in the selected video format and viewer. If this is not possible, the camera will override the settings and select the best available combination. Browser Viewer AMC QuickTime Windows Internet Explorer Java applet Description Recommended viewer in Windows Internet Explorer (MPEG-4 /Motion JPEG). MPEG-4 only. A slower imaging alternative to AMC. Requires one of the following installed on the client: · JVM (J2SE) 1.4.2 or higher · JRE (J2SE) 5.0 or higher Still image Server Push Other browsers QuickTime Java applet Still image Displays still images only. Hit the Refresh button in your browser to view a new image. Recommended viewer for other browsers (Motion JPEG). MPEG-4 only. A slower imaging alternative to Server Push (Motion JPEG only). Displays still images only. Hit the Refresh button in your browser to view a new image. AXIS 216FD - Live View Config Check the Show viewer toolbar box to display e.g. the AXIS Media Control (AMC) or the QuickTime viewer toolbar under the video image in your browser. 27 AMC Settings The administrator can disable the installation of the MPEG-4 decoder included with AMC. This is used to prevent the installation of unlicensed copies. Further decoder licenses can be purchased from your Axis dealer. HTML Examples You can add live video from the AXIS 216FD to your own web site. The camera can transmit a Motion JPEG stream to up to 20 simultaneous connections, although an administrator can restrict this to fewer. If MPEG-4 is set as video format, multicasting is used and the video stream will be available for an unlimited number of viewers connected to the parts of the network where multicast is enabled. Please note that a separate MPEG-4 license is required for each viewer. Select the preferred Video Format from the drop down list. The available options are Motion JPEG, MPEG-4 using AMC and MPEG-4 using QuickTime. The Motion JPEG selection has additional settings for Image Type, Image size and other optional settings to configure the video stream to suit your Web page. Click Update once satisfied. The camera generates the required source code for your configuration. Copy this code and paste it into your own Web page code. External Video The AXIS 216FD can also display video images from other Axis network cameras and video servers, directly on the Live View page. These are known as External Video sources. Once configured, these external video sources are available from the drop-down list on the Live View page. Click the Add button to open the External Video Source Setup dialog, which is used to make all the necessary settings. Enter the IP address or host name of the external video source you wish to add. Depending on the external source, select either MPEG-2, MPEG-4 or Motion JPEG as the type of video stream to receive. Sequence Mode The Live View page can be configured to rotate through the internal and selected external video sources, in order, or randomly. Select the desired video sources and enter the time in seconds to display each source (up to 59 minutes). Click Save. The Sequence buttons will appear on the Live View page to enable the viewer to start and stop the sequence mode. 28 AXIS 216FD - Event Configuration Event Configuration An event in the camera is when an Event Type is activated and causes certain actions to be performed. The event type is the set of parameters (or conditions) that specifies how and when which actions will be performed. A common event type is when the camera uploads images when an alarm occurs. Many event types use an Event Server, to receive uploaded images. This section describes how to set up event servers and event types, i.e. how to configure the camera to perform certain actions when events (e.g. alarms) occur. Definitions Event type Triggered Event - see page 29 A set of parameters describing how and when the camera will perform certain actions The circumstances that start an event. E.g. on a signal from an external device, such as a door switch or a motion sensor. E.g. at a pre-programmed time. E.g. the upload of images to an FTP server, e-mail notification, etc. Scheduled Event - see page 30 The circumstances that start an event. Action What occurs when the event triggers. Event Servers Event Servers are used to receive e.g. uploaded image files and/or notification messages. To set up Event server connections in your camera, go to Setup > Event Configuration > Event Servers and enter the required information for the required server type. Server type FTP Server Purpose · Receives uploaded images Information required · · · · · · Descriptive name of your choice Network address (IP address or host name) User Name and Password (for FTP server) Upload path e.g. images/ Port number Use passive mode if there is a firewall between the camera and FTP server · Use temporary file if your FTP server doesn't allow an existing file to be overwritten by a new file with the same name · · · · · · · · · Descriptive name of your choice URL (IP address or host name) User Name and Password (for HTTP server) Proxy address/Proxy port (if required) Proxy User Name and Password (if required) Descriptive name of your choice Network address (IP address or host name) User Name and Password (for TCP server) Port number HTTP Server · Receives notification messages · Receives uploaded images TCP Server · Receives notification messages For details on each setting, please see the online help available from each web page. When the setup is complete, the connection can be tested by clicking the Test button (the connection test takes approximately 10 seconds). AXIS 216FD - Event Configuration 29 Configuring Event Types An Event Type describes how and when the camera will perform certain actions. Example:: If somebody passes in front of the camera and an event that uses motion detection has been configured to act on this, the camera can e.g. record and save images to an FTP server, and/or send a notification e-mail to a pre-configured e-mail address with a pre-configured message. Images can be sent as e-mail attachments. Triggered Event A Triggered event can be activated by e.g: · · · · · a push button connected to the camera's input port detected movement in a configured motion detection window a manually activated action, e.g. from an action button in the web interface audio that is e.g. louder than a specified level on restart (reboot) after e.g. power loss How to set up a triggered event This example describes how to set up the camera to upload images when e.g the main door is opened: 1. Click Add triggered on the Event types page. 2. Enter a descriptive name for the event, e.g. Main door open. 3. Set the priority - High, Normal or Low (see the online help). 4. Set the Respond to Trigger... parameters for when the event will be active, e.g. only after office hours. 5. Select the trigger alternative from the Triggered by... drop-down list, e.g. select Input ports, for a sensor connected to the door. 6. Set the When Triggered... parameters, i.e. define what the camera will do if the main door is opened e.g., upload images to an FTP server or send an e-mail notification. 7. Click OK to save the Event in the Event Types list. Please see the online help Note: for descriptions of each available option. Up to 10 event types can be configured in the camera, and up to 3 of these can be configured to upload images. Files names can be formatted according to specific requirements. See File Naming & Date/Time Formats online help. 30 AXIS 216FD - Event Configuration Pre-trigger and Post-trigger buffers This function is very useful when checking to see what happened immediately before and/or after a trigger, e.g. 30 seconds before and/or after a door was opened. Check the Upload images checkbox under Event Types > Add Triggered... > Triggered by... to expand the web page with the available options. All uploaded images are JPEG images. Include pre-trigger buffer - images stored internally in the server from the time immediately preceding the trigger. Check the box to enable the pre-trigger buffer, enter the desired length of time and specify the required image frequency. Include post-trigger buffer - contains images from the time immediately after the trigger. Configure as for pre-trigger. Notes: ·Pre-trigger and Post-trigger buffers will be lost if the connection to the event server fails. ·The maximum length of the pre-/post-buffer depends on the video image size and selected frame rate. ·If the pre- or post-buffer is too large for the camera's internal memory, the frame rate will be reduced and individual images may be missing. If this occurs, an entry will be created in the unit's log file. Continue image upload (unbuffered) - enables the upload of video images for a fixed length of time. Specify the length of time for the uploaded recording, in seconds, minutes or hours, or for as long as the trigger is active. Finally, set the desired image frequency to the maximum (the maximum available) or to a specified frame rate. The frame rate will be the best possible, but might not be as high as specified, especially if uploading via a slow connection. Scheduled Event A Scheduled event can be activated at preset times, in a repeating pattern on selected weekdays. Configuration example: 1. Click Add scheduled on the Event types page. 2. Enter a descriptive name for the event, e.g. "Scheduled e-mail upload." 3. Set the priority (High, Normal or Low). 4. Set the Activation Time parameters (24h clock) when the event will be active, e.g. start on Sundays at 13.00 with a duration of 12 hours. 5. Set the When Activated... parameters, i.e. set what the camera will do at the specified time, e.g. send uploaded images to an e-mail address. 6. Click OK to save the Event in the Event Types list. Please see the online help for descriptions of each available option. AXIS 216FD - Event Configuration 31 Motion Detection Motion detection is used to generate an alarm whenever movement occurs (or stops) in the video image. A total of 10 Include and/or Exclude windows can be configured. · Included windows target specific areas within the whole video image · Excluded windows define areas within an Include window that should be ignored (areas outside Include windows are automatically ignored) Once configured, the motion detection windows will appear in the list of available triggers, for triggering events. See How to set up a triggered event above. Note: Using the motion detection feature may decrease the camera's overall performance. Configuring Motion Detection 1. Click Motion Detection in the Event Configuration menu. 2. Click the Configure Included Window radio button and click New. 3. Enter a descriptive name under Window name. 4. Adjust the size (drag the bottom right-hand corner) and position (click on the text at the top and drag to the desired position). 5. Adjust the Object size, History and Sensitivity profile sliders (see table below for details). Any detected motion within an active window is then indicated by red peaks in the Activity window (the active window has a red frame). 6. Click Save. To exclude parts of the Include window, click the Configure Excluded Windows button and position the Exclude window as required, within the Include window. Please see the online help for descriptions of each available option. 32 AXIS 216FD - Event Configuration Object Size High level Only very large objects trigger motion detection Even very small objects trigger motion detection Low History An object that appears in the region will trigger the motion detection for a long period An object that appears in the region will trigger motion detection for only a very short period Medium to High Sensitivity Ordinary colored objects on ordinary backgrounds will trigger the motion detection Only very bright objects on a dark background will trigger motion detection Medium to High Low level Default value Examples: · · · Avoid triggering on small objects in the video image by setting the object size level to high. To reduce the number of triggers if there is a lot of movement during a short period of time, select a high history level. To only detect flashing light, low sensitivity can be selected. In other cases, a high sensitivity level is recommended. Port Status Under Event Configuration > Port Status there is a list showing the status for the camera's input and output. This is for the benefit of Operators, who have no access to the System Options section. Example: If the Normal state for a push button connected to an input is set to Open circuit - as long as the button is not pushed, the state is inactive. If the button is pushed, the state of the input changes to active. AXIS 216FD - System Options 33 System Options Security User access control is enabled by default. An administrator can set up other users, by giving these user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page, as described below: Users - the user list displays the authorized users and user groups (levels): Viewer Operator Administrator Provides the lowest level of access, which only allows access to the Live View page. An Operator can view the Live View page, create and modify events and adjust certain other settings. Operators have no access to the System Options. An administrator has unrestricted access to the Setup Tools and can determine the registration of all other users. User Settings - check the relevant checkboxes to enable: · Anonymous viewer login - allows any viewer direct access to the Live View page. · Maximum number of simultaneous viewers - enter a value here to restrict the number of Motion JPEG and MPEG-4 viewers accessing the unit. This is useful if you need to save on bandwidth. Note that within the limit of 20 users, all multicast viewers count as 1 viewer. IP Address Filtering Enable IP Address Filtering to allow or deny access to the AXIS 216FD. Once enabled, the IP addresses in the list will be allowed or denied access according to the choice made in the drop-down list Allow/Deny the following IP addresses. The administrator can add up to 256 IP address entries to the list (a single entry can contain multiple IP addresses). The users from these IP addresses need to be specified in the user list with the appropriate access rights. This is done from Setup > System Options > Security > Users. Referrals To prevent unauthorized clients from including the video stream from the cameras into external Web pages, check the Referrals checkbox and enter the IP address or Host name of the computer that hosts the Web pages with the included video stream. Several IP addresses/host names can be defined and are separated by semicolons (;). This option is only applicable to Motion JPEG video streams. 34 AXIS 216FD - System Options Notes: ·If the referrals feature is enabled and you wish to also allow normal access to the Live View page, the product's own IP address or host name must be added to the list of allowed referrers. ·Restricting referrers has no effect on an MPEG-4 video stream. To restrict an MPEG-4 stream, IP address filtering must be enabled. ·Restricting referrers is of greatest value when not using IP address filtering. If IP address filtering is used, then the allowed referrers are automatically restricted to those allowed IP addresses. HTTPS The AXIS 216FD supports encrypted browsing using HTTPS. A self-signed certificate can be used until a Certificate Authority-issued certificate has been obtained. Click the Create self-signed Certificate button to install a self-signed certificate. Although self-signed certificates are free and offer some protection, true security will only be implemented after the installation of a signed certificate issued by a certificate authority. A signed certificate can be obtained from an issuing Certificate Authority by clicking the Create Certificate Request button. When the signed certificate is returned, click the Install signed certificate button to import the certificate. The properties of any certificate request currently resident in the camera or installed can also be viewed by clicking the Properties... button. The HTTPS Connection Policy must also be set in the drop-down lists to enable HTTPS in the camera. For more information, please refer to the online help. Date & Time Current Server Time - displays the current date and time (24h clock). The time can be displayed in 12h clock format in the Overlay (see below). New Server Time - Select your time zone from the drop-down list. If you want the server clock to automatically adjust for daylight savings time, select the Automatically adjust for daylight saving time changes. From the Time Mode section, select the preferred method to use for setting the time: · Synchronize with computer time - sets the time from the clock on your computer. · Synchronize with NTP Server - the camera will obtain the time from an NTP server every 60 minutes. · Set manually - this option allows you to manually set the time and date. Note: · If using a host name for the NTP server, a DNS server must be configured under TCP/IP settings. See Network > TCP/IP below. AXIS 216FD - System Options Date & Time Format Used in Images - specify the formats for the date and time (12h or 24h) displayed in the video streams. Use the predefined formats or use your own custom date and time formats. See Advanced for information on how to create File Naming & Date/Time Formats in the online help your own file formats. 35 Network - Basic TCP/IP Settings IP Address Configuration In the AXIS 216FD these settings are grouped according to the network interface. The camera's IP address can be set automatically via DHCP, or a fixed IP address can be set manually. A host name can be used and there are options for setting up notification of changes in the IP address. DHCP is enabled by default. Notes: · DHCP is a protocol for automatic IP address assignment on a network. IP address assignment via DHCP may lead to the situation where the IP address changes and you lose contact. Configure the options for notification of IP address change (under Services) to receive notification from the camera when the IP address changes. · Alternatively, if your DHCP server can update a DNS server, you can access the AXIS 216FD by host name which is always the same, regardless of the IP address. Services Options for notification of IP address change - if the IP address for the camera changes, e.g. automatically by DHCP, you can choose to be notified of the change. Click Settings... and enter the required information. AXIS Internet Dynamic DNS Service - use the AXIS Internet Dynamic DNS service to assign a host name for easy access to your AXIS 216FD Network Camera (requires Internet access). Click Settings... to register your AXIS 216FD with the Axis Internet Dynamic DNS service, or to modify the existing settings (requires access to the Internet). The domain name currently registered at the Axis Internet Dynamic DNS service for your product can at any time be removed. For more information, please refer to the online help. Network - Advanced TCP/IP Settings DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses on your network. 36 AXIS 216FD - System Options Obtain DNS server address via DHCP - automatically use the DNS server settings provided by the DHCP server. Click the View button to see the current settings. Use the following DNS server address - enter the desired DNS server by specifying the following: Domain name - enter the domain(s) to search for the host name used by the AXIS 216FD. Multiple domains can be separated by semicolons (;). The host name is always the first part of a Fully Qualified Domain Name, e.g. myserver is the host name in the Fully Qualified Domain Name myserver.mycompany.com where mycompany.com is the Domain name. DNS servers - enter the IP addresses of the primary and secondary DNS servers. NTP Configuration Obtain NTP server address via DHCP - check this radio button to automatically look up and use the NTP server settings as provided by DHCP. Click the View button to see the current settings. Use the following NTP server address - to make manual settings, check this radio button and enter the host name or IP address of the NTP server. Host Name Configuration The AXIS 216FD can be accessed using a host name, instead of an IP address. The host name is usually the same as the assigned DNS Name. For more information, please see the online help. Link-Local Address This is enabled by default and assigns the AXIS 216FD an additional IP address for use with UPnPTM. The AXIS 216FD can have both a Link-Local IP and a static/DHCP-supplied IP address at the same time - these will not affect each other. HTTP The default HTTP port number (80) can be changed to any port within the range 1024-65535. This is useful for e.g. simple security port mapping. NAT traversal (port mapping) A broadband router allows devices on a private network (LAN) to share a single connection to the Internet. This is done by forwarding network traffic from the private network to the "outside" i.e. the Internet. Security on the private network (LAN) is increased since most broadband routers are pre-configured to stop any attempts to access the private network (LAN) from the public network/Internet. AXIS 216FD - System Options Use NAT traversal when your AXIS 216FD is located on an intranet (LAN) and you wish to make it available from the other (WAN) side of a NAT router. With NAT traversal properly configured, all HTTP traffic to an external HTTP port in the NAT router will be forwarded to the camera. LAN (intranet) Broadband (NAT) router 37 WAN (internet) ISP Notes: · For NAT traversal to work, this must also be supported by the broadband router. · The broadband router has many different names: "NAT router", "Network router", Internet Gateway", "Broadband sharing device" or "Home firewall" but the essential purpose of the device is the same. Enable/Disable - When enabled, the AXIS 216FD will attempt to configure port mapping in a NAT router on your network, using UPnPTM. Note that UPnPTM must be enabled in the camera (see System Options > Network > UPnP). AXIS Internet Dynamic DNS Service - Use this free service to assign a host name (user-friendly name) for easy access to your camera. If the IP address of the camera or NAT router changes, the AXIS Internet Dynamic DNS Service will automatically be updated with the new IP address. Use manually selected NAT router - Select this option to manually select a NAT router and enter the IP address for the router in the field provided. If a router is not manually specified, the AXIS 216FD will automatically search for NAT routers on your network. If more than one router is found, the default router will be selected. Alternative HTTP port - Select this option to manually define an external HTTP port. Enter the port number in the field provided. If no port is entered here a port number will automatically be selected when NAT traversal is enabled. Notes: · An alternative HTTP port can be used/be active even if NAT traversal is disabled. This is useful if e.g. your NAT router does not support UPnP and you need to manually configure port forwarding in the NAT router. · If a manually selected port is already in use, another will automatically be selected. · When the port is selected automatically it will be displayed in this field. This can be changed by entering a new port number and clicking Save. 38 AXIS 216FD - System Options RTSP The RTSP protocol allows a connecting client to start an MPEG-4 stream. Enter the RTSP port number to use. The default setting is 554. Network Traffic Connection Type - The default setting is Auto-negotiate, which means that the correct speed is automatically selected. If necessary, you can set the connection speed by selecting it from the drop-down list. SOCKS SOCKS is a networking proxy protocol. The AXIS 216FD can be configured to use a SOCKS server to reach networks on the other side of a firewall/proxy server. This functionality is useful if the AXIS 216FD is located on a local network behind a firewall, but notifications, uploads, alarms, etc., need to be sent to a destination outside the local network (e.g. to the Internet). SMTP (email) Enter the host names or addresses for your primary and secondary mail servers in the fields provided, to enable the sending of notifications and image/video email messages from the camera to predefined addresses via SMTP. If your mail server requires authentication, check the box for Use authentication to log in to this server and enter the necessary information. SNMP The Simple Network Management Protocol (SNMP) allows remote management of network devices. Depending on the level of security required, select the version of SNMP to use. The three levels of security are: · SNMP V1 - includes no security. · SNMP V2c - uses very simple security. The community name can be specified as a password for read or read/write access to all supported SNMP objects. The community is the the group of network devices using SNMP. · SNMP V3 - provides encryption and secure passwords. HTTPS must be enabled. UPnPTM The camera includes support for UPnPTM, which is enabled by default. If also enabled on your computer, the camera will automatically be detected and a new icon will be added to "My Network Places." Note: UPnP must also be enabled on your Windows XP or ME computer. To do this, open the Control Panel from the Start Menu and select Add/Remove Programs. Select Add/Remove Windows Components and open AXIS 216FD - System Options the Networking Services section. Click Details and then select UPnP as the service to add. 39 RTP / MPEG-4 These settings are the port range, IP address, port number (video and audio), and Time-To-Live value to use for the video stream(s) in multicast MPEG-4 format. Only certain IP addresses and port numbers should be used for multicast streams. For more information, please see the online help. Ports & Devices I/O Ports - the pinout, interface support and the control and monitoring functions provided by this connector are described in The I/O Terminal Connector, on page 42. LED Settings The Status indicator LED on the front of the camera can be set to flash at a configurable interval (or to not light up at all) whenever the unit is accessed. For a listing of all LED behavior, see page 8, or the online help. Note that the LED does not flash when the stream is retrieved using MPEG-4 multicast. Maintenance · Restart - The camera is restarted without changing any of the settings. · Restore - The unit is restarted and most current settings are reset to factory default values. The settings that will not be reset are as follows: · the boot protocol (DHCP or static) · the static IP address · the default router · the subnet mask · Default - The default button should be used with caution. Pressing this will return all of the camera's settings to the factory default values (including the IP address) Upgrade Server - See Upgrading the Firmware, on page 44. Backup - To take a backup of all of the parameters, and any user-defined scripts, click this button. If necessary, it will then be possible to return to the previous settings, if settings are changed and there is unexpected behavior. Restore - click the Browse button to locate the saved backup file (see above) and then click the Restore button. The settings will be restored to the previous configuration. Note: Backup and Restore can only be used on the same unit running the same firmware. This feature is not intended for the configuration of multiple units or for firmware upgrades. 40 AXIS 216FD - System Options Support The support overview page provides valuable information on troubleshooting and contact information, should you require technical assistance. System Overview - is a quick look over the camera's status and settings. Information that can be found here includes the camera's Firmware version, IP address, Security, Event and Image settings and Recent log items. Many of the captions are also links to the proper Setup page to conveniently make adjustments in the cameras settings. Logs & Reports - when contacting Axis support, please be sure to provide a valid Server Report with your query. View Information - The Log file, the Server Report and the Parameter List all provide valuable information for troubleshooting and when contacting Axis support. Configuration Log Level for Log Files - from the drop-down list, select the level of information to be added to the Log file Log Level for Email - from the drop-down list, select the level of information to send as email and enter the destination email address. AXIS 216FD - System Options 41 Resetting to the Factory Default Settings To reset the camera to the original factory default settings, go to the System Options > Maintenance web page (as described in Maintenance, on page 39) or use the Control button on the underside of the camera (see page 7) as described below: Using the Control Button To reset the camera to the factory default settings using the Control Button: 1. Disconnect the power adapter. 2. Press and hold the Control button while reconnecting the power. 3. Keep the Control button pressed until the Status Indicator color changes to amber (this may take up to 15 seconds). 4. Release the Control button. 5. When the Status Indicator changes to Green (which may take up to 1 minute), the process is complete and the camera has been reset. The unit will now have the default IP address 192.168.0.90 Advanced Scripting is an advanced function that provides the possibility to customize and use scripts. This function is a very powerful tool. Caution! Improper use may cause unexpected behavior or even cause loss of contact with the unit. If a script does cause problems, reset the unit to its factory default settings. A backup file may be of use to return the unit to its latest configuration. Axis strongly recommends that you do not use this function unless you fully understand the consequences. Note that Axis support does not provide assistance for problems with customized scripts. For more information, please visit the Developer pages at www.axis.com/developer Plain Config - this function is for the advanced user with experience of Axis network camera configuration. All parameters can be set and modified from this page. Help is available from the standard help pages. 42 AXIS 216FD - The I/O Terminal Connector The I/O Terminal Connector Pinout and Interface The 4-pin I/O terminal connector provides the interface to: · 1 transistor output · 1 digital input · auxiliary power and GND The terminal connector is used in applications for e.g. motion detection, event triggering, time lapse recording, alarm notification via email, image storage to FTP locations, etc. · Input - for connecting e.g. a push button. If the push button is pressed, the state changes and the input becomes active (shown under Event Configuration > Port Status). · Output - connects e.g. an alarm device that can be activated by Output buttons on the Live View page, or by an Event Type. The output will show as active (Event Configuration > Port Status) if the alarm device is activated. I/O terminal connector: Pin 4 Function Transistor Output Description With a maximum load of 50mA and a maximum voltage of 24V DC, this output has an open-collector NPN transistor with the emitter connected to the GND pin. If used with an external relay, a diode must be connected in parallel with the load, for protection against voltage transients. Connect to GND to activate, or leave floating (or unconnected) to deactivate. Can be used to power auxiliary equipment, max 50mA. 3 2 1 Digital Input 3.3V DC GND I/O terminal connector AXIS 216FD - The I/O Terminal Connector Connect input/output devices to the camera as follows: 1. Attach the cables for the device securely to the supplied green connector block. 2. Once the cables are connected, push the connector block into the green terminal connector on the camera. 43 Terminal Connectors AXIS 216FD 1 o 3.3V, max. 50mA 2o 3o 4 e.g. doorbell o 44 AXIS 216FD - Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of the AXIS 216FD. One of your first actions when troubleshooting a problem should be to check the currently installed firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in your camera can be seen on the page Setup > Basic Configuration. Upgrading the Firmware When you upgrade the firmware with a file from the Axis Web site, your camera will receive the latest available functionality. Always read the upgrade instructions and release notes available with each new release, before updating the firmware. Note: Preconfigured and customized settings will be saved when the firmware is upgraded (providing the features are available in the new firmware) although this is not guaranteed by Axis Communications. Always read the instructions and release notes available with each new release, before upgrading the firmware. 1. Save the firmware file to your computer. The latest version of the firmware is available free of charge from the Axis Web site at www.axis.com/techsup 2. Go to Setup > System Options > Maintenance in the camera's Web pages. 3. In the Upgrade Server section, browse to the desired firmware file on your computer. Click Upgrade. Notes: ·After starting the upgrade process, always wait at least 5-10 minutes before restarting the camera, even if you suspect the upgrade has failed. ·Your dealer reserves the right to charge for any repair attributable to faulty upgrading by the user. AXIS Camera Management software tool can be used for multiple upgrades. Refer to the Axis Web site at www.axis.com for more information. AXIS 216FD - Troubleshooting 45 Emergency Recovery Procedure If power or the network connection to the camera is lost during the upgrade, the process will fail and the unit will become unresponsive. A flashing red Status LED indicates a failed upgrade. To recover the unit, follow the steps below. The serial number is found on the label attached to the bottom of the camera. 1. Unix/Linux - From the command line, type the following: arp -s temp ping -s 408 Windows - From a command/DOS prompt, type the following: arp -s ping -l 408 -t 2. If the unit does not reply within a few seconds, restart it and wait for a reply. Press CTRL+C to stop Ping. 3. Open a browser and type in the camera's IP address. In the page that appears, use the Browse button to select the upgrade file to use, e.g. axis216fd.bin. Then click the Load button to restart the upgrade process. 4. After the upgrade has completed (1-10 minutes), the unit will automatically restart and show a steady green on the Power and Status LEDs and flashing green or amber on the Network LED. 5. Referring to the installation guide, reinstall the camera. If the emergency recovery procedure does not get the camera up and running again, please contact Axis support at www.axis.com/techsup/ Axis Support If you contact Axis support, please help us to help you solve your problems, by providing the server report, the log file and a brief description of the problem. Server Report - go to Setup > System Options > Support Overview. The server report contains important information about the server and its software, as well as a list of the current parameters. The Log file is available from Setup > System Options > Logs & Reports. The Log file records events in the unit since the last system restart and can be a useful diagnostic tool when troubleshooting. 46 AXIS 216FD - Troubleshooting Symptoms, Possible Causes and Remedial Actions Problems setting the IP address When using ARP/Ping Try the installation again. The IP address must be set within two minutes after power has been applied to the camera. Ensure the Ping length is set to 408. See the Installation Guide. If the IP address intended for the camera and the IP address of your computer are located on different subnets, you will not be able to set the IP address. Contact your network administrator to obtain an appropriate IP address. Disconnect the camera from the network. Run the Ping command. (In a Command/DOS window, type ping and the IP address of the unit). If you receive: Reply from : bytes = 32; time = 10 ms..... - this means that the IP address may already be in use by another device on your network. You must obtain a new IP address and reinstall the unit. If you see: Request timed out - this means that the IP address is available for use with your camera. In this case, check all cabling and reinstall the unit. Possible IP address conflict with another device on the same subnet The static IP address in the camera is used before the DHCP server sets a a dynamic address. This means that if the same default static IP address is also used by another device, there may be problems accessing the camera. To avoid this, set the static IP address to 0.0.0.0. 1) Move the camera to an isolated network or to one with no DHCP or BOOTP server. Set the IP address again, using the AXIS IP Utility (see the Installation Guide) or the ARP/Ping commands. 2) Access the unit and disable DHCP in the TCP/IP settings. Return the unit to the main network. The unit now has a fixed IP address that will not change. 3) As an alternative to 2), if dynamic IP address via DHCP or BOOTP is required, select the required service and then configure IP address change notification from the network settings. Return the unit to the main network. The unit will now have a dynamic IP address, but will notify you if the address changes. Test the network cable by connecting it to another network device, then Ping that device from your workstation. See the instructions above. To configure your broadband router to allow incoming data traffic to the camera: Enable the NAT-traversal feature which will attempt to automatically configure the router to allow access to the camera. This is enabled from Setup > System Options > Network > TCP/IP Advanced. Check the Internet firewall with your system administrator. Check if you need to configure the default router settings. Check that the correct network interface is selected in the AMC control panel applet (network tab). Check that the relevant MPEG-4 connection methods are enabled in the AMC control panel applet (network tab). In the AMC control applet, select the MPEG-4 tab and click the button Set to default MPEG-4 decoder. No multicast MPEG-4 displayed in the client Check with your network administrator that the multicast addresses used by the camera are valid for your network. Check with your network administrator to see if there is a firewall preventing viewing. Multicast MPEG-4 only accessible by Check if your router supports multicasting, or if the router settings between the client and local clients the server need to be configured. The TTL (Time To Live) value may need to be increased. The camera is located on a different subnet The IP address is being used by another device The camera cannot be accessed from a browser The IP address has been changed by DHCP Other networking problems Camera is accessible locally, but not externally Broadband router configuration Firewall protection Default routers required Problems with the MPEG-4 format No MPEG-4 displayed in the client AXIS 216FD - Troubleshooting Poor rendering of MPEG-4 images Color depth set incorrectly on clients. Set to 16-bit or 32-bit color. If text overlays are blurred, or if there are other rendering problems, you may need to enable Advanced Video Rendering from the MPEG-4 tab in the AMC control panel applet. Ensure that your graphics card is using the latest device driver. The latest drivers can usually be downloaded from the manufacturer's web site. Color saturation is different in MPEG-4 and Motion JPEG Lower frame rate than expected Modify the settings for your graphics adapter. Please see the adapter's documentation for more information. Reduce number of applications running on the client computer. Check with the system administrator that there is enough bandwidth available. See also the online help. Check in the AMC control panel applet (MPEG-4 tab) that video processing is not set to Decode only I frames. Lower the image resolution. Lost or poor images in pre-trigger buffer (MPEG-4 video stream) Image degeneration Faulty power supply Make sure that Cyclic refresh under Setup > Video & Image > Advanced > MPEG-4 is disabled. Decrease the GOV length, see the online help for more information. Check that you are using an AXIS PS-L power supply. 47 The Power indicator is not constantly lit The Status and Network indicator LEDs are flashing red rapidly Hardware failure Contact your Axis dealer. The Status indicator LED is flashing red and the camera is inaccessible A firmware upgrade has been inter- See the Emergency Recovery Procedure above. rupted or the firmware has otherwise been damaged No images displayed on web page Problem with AMC. (Internet Explorer only) Installation of additional ActiveX component restricted or prohibited Video/Image problems, general Image too dark or too light Missing images in uploads Slow image update Poor performance Check the video image settings. See the online help on Video and Image Settings. This can occur when trying to use a larger image buffer than is actually available. Try lowering the frame rate or the upload period. Configuring, e.g. pre-buffers, motion detection, high-resolution images, high frame rates, etc, will reduce the performance of the camera. Poor performance may be caused by e.g. heavy network traffic, multiple users accessing the unit, low performance clients, use of features such as Motion Detection, Event handling, Image rotation other than 180 degrees. To enable the updating of video images in Microsoft Internet Explorer, set your browser to allow ActiveX controls. Also, make sure that AXIS Media Control (AMC) component is installed on your workstation. Configure your camera to use a Java applet for updating the video images under Live View Config > Layout > Default Viewer for Internet Explorer. See the online help for more information. Poor quality snapshot images Screen incorrectly configured on your In Display Properties, configure your screen to show at least 65000 colors, i.e. at least workstation 16-bit. Using only 16 or 256 colors will produce dithering artifacts in the image. Browser freezes Netscape 7.x or Mozilla 1.4 (or later) Lower the image resolution. can sometimes freeze on a slow computer 48 AXIS 216FD - Troubleshooting Problems uploading files Limited space Motion Detection triggers unexpectedly Changes in luminance Motion detection is based upon changes in luminance in the image. This means that if there are sudden changes in the lighting, motion detection may be triggered mistakenly. Lower the sensitivity setting to avoid problems with luminance. Check the sound card in the PC. Ensure that the mute button is not pressed and the volume settings are correct. Check that the correct Audio Input source is selected under Setup > Audio > Source. Select Microphone for the internal microphone or for a connected external microphone. Select Line for a connected line in source. The volume of the microphone is either too high or too low. Change the volume for the microphone in the toolbar on the Live View page. Too many users/clients connected to the camera may affect the sound quality adversely. Try limiting the number of clients allowed to connect under Basic Configuration > Users. Reduce the number of listeners and viewers and decrease the image resolution and compression. It is recommended that the camera's time setting is synchronized with an NTP Server. This is enabled under System Options > Date & Time. Check that the correct Audio Input source is selected under Setup > Audio > Source. Select Microphone for the internal microphone or for a connected external microphone. Select Line for a connected line in source. Audio break-up (stuttering audio) can be reduced using the Buffer slider control on the Live View page. A higher level will reduce audio break-up, but may introduce a noticeable lag in audio transmission. There is only limited space available for the upload of your own files. Try deleting existing files to free up space. No audio Incorrect setup No audio or very poor audio quality Audio volume too low/high Volume settings incorrect Poor audio quality Too many users CPU overloaded Unsynchronized audio and video Distorted audio Stuttering audio For additional assistance, please contact your reseller or see the support pages on the Axis Website at www.axis.com/techsup AXIS 216FD - Technical Specifications 49 Technical Specifications Item Model Image sensor Lens Camera angle adjustment Minimum illumination Video compression Specification AXIS 216FD Fixed Dome Network Camera ¼" Progressive scan Micron CMOS sensor Fujinon, F1.3 varifocal 2.8-10 mm, DC-iris, horizontal viewing angle: 73°-20°, focus range: 0.5 m to infinity pan ±180°, tilt ±85°, rotation ±170° 1lux, F1.3 Motion JPEG MPEG-4 Part 2 (ISO/IEC 14496-2) with motion estimation, Profiles: Advanced Simple Profile and Simple Profile 9 resolutions from 640x480 to 160x120 via API, 5 selections via configuration web page Up to 30 frames per sec in VGA (Motion JPEG and MPEG-4) Simultaneous Motion JPEG and MPEG-4 Controllable frame rate and bandwidth Constant and variable bit rate (MPEG-4) Compression levels: 100 Rotation: 0º, 180º Configurable color level, brightness, sharpness, contrast, white balance, exposure control Overlay capabilities: time, date, text, image or privacy mask 1/4 - 1/15000 sec. Configurable for built-in or external microphone Audio compression - Audio in: AAC LC 8-32 kbit/s, G.711 PCM 64 kbit/s, G.726 ADPCM 32 or 24 kbit/s - Audio out: G.711 PCM 64 kbit/s Half duplex, simplex or audio off Audio alarm at configurable detection level Multiple user access levels with password protection, IP address filtering, HTTPS encryption 20 simultaneous users Unlimited number of users using multicast (MPEG-4) Events triggered by built-in multi-window motion detection, external inputs, audio detection or according to a schedule Image upload over FTP, email and HTTP Notification over TCP, email, HTTP and external output Pre- and post alarm buffer of 9 MB (approx. 5 min of 320x240 resolution video at 4 fps) Ethernet 10BaseT/100BaseTX, RJ-45 Mini DC power jack Terminal block for 1 alarm input and 1 output 3.5 mm jack for Mic in (max 80 mVpp) or Line mono input (max 6.4 Vpp), 3.5 mm jack for Line mono output (max 1.3 Vpp) to active speaker Input impedance: 2.4k Output impedance: Min. 16 Resolutions Frame rate Video streaming Image settings Shutter time Audio Security Users Alarm and event management Connectors 50 AXIS 216FD - Technical Specifications Item Casing Specification Tamper-resistant casing Polycarbonate clear dome glass Polycarbonate base Tamper-proof mounting on wall, hard or drop ceiling CPU, video processing and compression: ARTPEC-A, RAM: 32 MB, Flash: 8 MB Battery backed-up real-time clock 5.1 V DC max 3.6 W, or Power over Ethernet (IEEE 802.3af) with power classification: Class 1 (max 3.84 W) 0 ­ 50 ºC (32 ­ 122 ºF) Humidity 20 - 80% RH (non-condensing) AXIS Camera Management tool on CD and web-based configuration Configuration of backup and restore Firmware upgrades over HTTP or FTP, firmware available at www.axis.com Camera live view, sequence tour capability for up to 20 Axis video sources, customizable HTML pages Pentium III CPU 500 MHz or higher, or equivalent AMD 128 MB RAM AGP graphic card, Direct Draw, 32 MB RAM Windows XP, 2000, NT4.0*, ME* or 98*, DirectX 9.0 or later Internet Explorer 5.x or later For other operating systems and browsers see www.axis.com/techsup *Motion JPEG only Powerful API for software integration available at www.axis.com, including AXIS VAPIX API, AXIS Media Control SDK, event trigger data in video stream and embedded scripting. Watchdog secures continuous operation, can be monitored by other systems via event notification. Embedded operating system: Linux 2.4 IP, HTTP, HTTPS, SSL/TLS*, TCP, ICMP, SNMPv1/v2c/v3 (MIB-II), RTSP, RTP, UDP, IGMP, RTCP, SMTP, FTP, DHCP, UPnP, Bonjour, ARP, DNS, DynDNS, SOCKS, NTP etc. More information on protocol usage available at www.axis.com * This product includes software developed by the Open SSL Project for use in the Open SSL Tool kit (www.openssl.org) AXIS Camera Station - Surveillance application for viewing, recording and archiving up to 25 cameras. See www.axis.com/partner/adp_partners.htm for more software applications via partners Installation Guide, CD with installation and management tools, demo software and User's Manual, mounting and connector kits (extension cord, screws, screw driver, drill template, terminal connector) power supply 5.1 V DC, MPEG-4 licenses (1 encoder, 1 decoder), MPEG-4 decoder (Windows) Smoked dome glass Processors, memory, clock Power Operating conditions Installation, management and maintenance Video access from Web browser Minimum web browsing requirements System integration support Supported protocols Video management software (not included) Included accessories Accessories (not included)