INSIDE THIS INSTRUCTION MANUAL Important Safety Instructions / Features .......................................................................2 Product Features / Precautions.....................................................................................3 Amplifier and Mixer Descriptions .................................................................................4 Set-up & Warranty Information ....................................................................................5-7 Contact Information .....................................................................................................8 Read these instructions. Follow all instructions Keep these instructions Heed all warnings Do not use the MATRIX-200 near water. Be extra cautious when moving the system during rain or while transporting the system over wet surfaces as water might splash on to the amplifier. To reduce the risk of fire or electric shock, do not expose the system to rain or moisture. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Use in accordance with manufacturer's instructions. 8) Do not use near heat sources such as radiators, stoves or other devices that may produce heat. 9) Do not defeat the safety purpose of the polarization or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched, particularly at the plug and at the point where it exits the MATRIX-200 amplifier. 11) Only use attachments / accessories recommended by B-52 Pro-Audio. 12) Use caution when transporting the system to avoid injury from tip-over. 13) Unplug the MATRIX-200 during lightning storms or when not in use. 14) Refer all servicing to qualified personnel. Servicing is required when the MATRIX-200 has been damaged in any way, such as the power-cord or plug is damaged, liquid has been spilled into the cabinets, the unit has been exposed to moisture or rain, does not operate normally, or has been dropped. 15) The MATRIX-200 is not intended for outdoor fixed installations or in high moisture areas. Moisture can damage the speakers and can cause corrosion of electrical contacts. Keep speakers out of extended or intense direct sunlight. The speaker surfaces may fade and be damaged by long-term exposure to intense ultra-violent light. 1) 2) 3) 4) 5) IMPORTANT SAFETY INFORMATION HEED ALL WARNINGS CAUTION RISK OF ELE TRIC SH C OCK DO NOT OPEN WARNING: To reduce the risk or fire or electrical shock do not expose this equipment to rain or moisture. CAUTION: Connect the power cable only after you have made absolutely sure the local mains voltage matches the voltage specified on the device. If you connect to the wrong voltage, you may destroy the electronic components of the MATRIX-200 system. Stereo Power Amplifier features · Output stage with discrete devices, not integrated IC amps · Output power of 2 x 100w RMS with significant headroom for peaks · Comprehensive amplifier and speaker protection circuitry to guard against short circuits, DC offsets, over-heating, turn-on thumps, subsonic and supersonic frequencies. · Built-in stereo clip limiter · Equalization customized to enhance and optimize speaker system performance · Output for stereo headphones on rear panel · Very efficient cooling, utilizing a large heatsink and two direct flow fans · Power supply with low-noise torodial transformer and a dual voltage (115/230Vac) selector switch 5-Channel Mixer features · Four channels with both balanced XLR mic inputs and unbalanced 1/4" jack line level inputs n 15Vdc phantom power on balanced XLR inputs for condenser microphones n Independant PAN, TONE and EFFECT LEVEL controls on each channel · One stereo channel for variety of sources: n 1/4" TRS-style Stereo Phone Jack n 3.5mm Stereo Jack for MP3 / CD players n Dedicated mono 1/4" Jack INSTRUMENT input with frequency response contoured for acoustical instruments · Low distortion, low noise circuitry · PLAYBACK input/output RCA connectors with LEVEL control · PATCH section to connect optional external processors, external effects and foot switch · 3-band MASTER EQ section · XLR output for external subwoofer. · Sub switch not only engages low frequency output but also removes deep bass from satellites thus increasing dynamic range and lowering overall system distortion Loudspeakers · Dual 6.5" drivers optimized for D'Appolito (mirrored woofers) configuration · 1" exit phenolic tweeter on exponential horn ideally matches dual 6.5" speakers Built-in DSP Effects · Eight built-in high quality DSP effects n Level control to mix processed signal with main signal n INPUT/MASTER switch to route effects to either Master section or to individual channels · Sophisticated mixer topology allows the combination of external effect devices to be used in combination with internal DSP Complete system Dimensions: 20" (W) x 32" (H) x 15" (D) Weight: 80 (lbs) 2 Note: Specifications are subject to change without notice The MATRIX-200 Powered Stereo Mixer with DSP CONGRATULATIONS ON YOUR PURCHASE OF THIS B-52 PROFESSIONAL MATRIX-200. The MATRIX-200 is the newest member of the popular B-52 MATRIX family of active systems. Compact and portable, the MATRIX-200 can deliver powerful, clean and accurate sound, ideal for applications such as karaoke, music playback, or small stage soundreinforcement. The MATRIX-200 has a true 200-watt stereo amplifier, built-in 5-channel mixer, studio-quality digital effects, phantom power and numerous patch inputs / outputs. Caution: The system's components are matched for the best possible sound quality and may only be operated in the specified configuration provided in this manual. Use of other two-way speakers may hinder the sound quality and can damage the power amplifier. Speaker cables and suitcase to carry all three components are included Hearing damage, prolonged exposure to excessive SPL B-52 Pro-Audio speakers, including the MATRIX-200, are capable of producing sound pressure levels (SPL) sufficient to cause permanent hearing damage to performers, production crews or people in the audience. Hearing protection devices such as ear-plugs are recommended. Caution should be taken to avoid extended exposures to SPL levels in excess of 85 dB. Amplifier Module Precautions Do not attempt to service the MATRIX-200 by yourself. Refer all servicing to a B-52 Pro-Audio Authorized dealer. Service is required when the MATRIX-200 amplifier has been exposed to liquids or suffered damage. Do not operate the unit if liquid has spilled into the amplifier. Immediately remove the power cord from AC mains power if such an event should occur. WARNING ­ Shock Hazard To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture. Do not operate your MATRIX-200 near a pool or other standing water. Make sure all blades on the polarized power plug are fully inserted into the power source. Ensure the power cord is not stretched, pinched or otherwise abused. Ensure the power cord is routed to avoid foot traffic. Your MATRIX-200 amplifier should be cleaned only with a dry cloth. Cautions 1) 2) 3) When placed on slick, smooth or slippery surfaces, vibrating speakers may move from their original location. Precautions should be taken to insure the system does not fall off of a raised stage or platform. Please turn the volume down prior to turning the system on to prevent possible damage to the speakers. If you are using an optional active subwoofer with the MATRIX-200, be sure all cabling is connected to the MATRIX-200 from the subwoofer, the subwoofer's volume control(s), and the volume control of the MATRIX-200 are turned all the way down, before either unit is powered on. After connecting your source(s) to the MATRIX-200, make sure your MATRIX-200 and signal sources have their volume controls turned all the way down before powering on the MATRIX-200 to avoid turn on thumps that could damage your speakers. 4) 3 MATRIX-200 FRONT PANEL CONTROLS MASTER SECTION The Master Section gives the operator overall control of the settings that apply to all inputs. 1. MASTER - BASS: Adds or subtracts bass to the MATRIX-200 output. 2. MASTER - MID: Adds or subtracts the mid-range frequencies produced by the MATRIX-200. This control will add vocal clarity or instrument presence. 3. MASTER - TREBLE: Adds or subtracts the high range frequencies in the overall mix. 4. MASTER - PLAYBACK: Controls the volume of the playback input jacks, shown as No.23 on the diagram (right). 5. DIGITAL EFFECTS - LEVEL: Controls the mix level of the built in effects. 6. MASTER - DIGITAL EFFECTS: The MATRIX-200 features eight versatile settings designed to suit a host of differing musical needs and tastes such as Large Hall, Large Room, Small Hall, Small Room, Echo, Slap Back, Chorus Reverb and Chorus. 7. DIGITAL EFFECTS SOURCE: MASTER/INPUT SWITCH: Controls routing internal DSP effects to either MASTER section, or to individual channels. 8. MASTER - POWER: When this LED is illuminated, the MATRIX-200 is connected to AC mains voltage and powered on. 9. MASTER - VOLUME: Controls overall volume of the MATRIX-200 except for the playback inputs (See Description 4). 16. INPUT ­ MP3/CD: 3.5mm stereo pin plugs (TRS style) connects so that your portable music source(s) can be used as an input to play through your MATRIX-200. 17. INPUT ­ INSTRUMENT: 1/4" jack input for string instrument, such as acoustical guitar with passive pickup, or electrical guitar. 18. INPUT ­ MIC: Balanced XLR inputs to connect low-impedance microphones to channels 1-4. These inputs will accept virtually any microphones, both dynamic and condenser. All four XLR inputs are phantom powered to provide voltage required by condenser microphones. These inputs will also accept any mic-level balanced signals. PATCH SECTION 19. INSERT INPUT/OUTPUT LEFT and RIGHT: 1/4" jacks to connect external processing device, such as compressor or equalizer to MATRIX-200. Each 1/4" jack has input and output; one jack for Left channel and one jack for Right channel. SLEEVE on 1/4" jack is connected to the ground. RING must be connected to the input of external device, and TIP must be connected to the output of external device. Please refer to the diagram labeled "Y-Cable Setup" on Page 7 of this manual for a graphic depiction of this. NOTE: Different processors may have a different configuration than the MATRIX-200 on their connectors. Please review the manual information of the external processor before assuming it is the same as the MATRIX-200. If the external processor uses a different connection standard, then you will likely need to buy adaptors to properly connect the two units together. NOTE: Do not insert Mono 1/4" jacks into insert jacks. 20. EFFECTS SEND/RETURN LEFT and RIGHT: 1/4" jacks to connect external effects processor. Each 1/4" jack has input and output; one jack for Left channel, and one jack for Right channel. SLEEVE on 1/4" jack is connected to the ground. RING must be connected to the input of external processor, and TIP must be connected to the output of external processor. Please refer to the diagram labeled "Y-Cable Setup" on Page 7 of this manual for a graphic depiction of this. NOTE: Different processors may have a different configuration than the MATRIX-200 on their connectors. Please review the instruction manual information of the external processor before assuming it is the same as the MATRIX-200. If the external processor uses a different connection standard, then you will likely need to buy adaptors to properly connect the two units together. NOTE: Do not insert Mono 1/4" jacks into insert jacks. 21. FOOTSWITCH EFFECTS/MUTE: This 1/4" jack is used to connect footswitch to remotely mute digital effects and master volume. 22. RECORD OUTPUTS: RCA jacks to connect stereo recording device to MATRIX-200. This record output is unaffected by the Master volume control. 23. PLAYBACK INPUTS: RCA jacks used to connect stereo source to MATRIX-200. This input bypasses all controls, including Master Volume (9) and Equalizer (1), (2), and (3), and is controlled only by playback level control (4). It is also not affected by Mute Footswitch (22). INPUT SECTION The Input section of the MATRIX-200 controls various aspects of the external audio sources which can be plugged into the mixer, including microphones, guitars, keyboards and certain other devices equipped with either 1/4" jacks, 3.5mm stereo jacks, or microphone outputs 10. INPUT - EFFECTS: Controls level of each individual channel routed to digital effects section when Effects Master/Input switch is in Source position. These controls are not active when Effects Master/Input ...