User manual BBE SOUND DS24

DIGITAL SPEAKER PROCESSOR DS24/DS26 ·User Guide ·Reference Manual professional products ® IMPORTANT SAFEGUARDS i CONTENTS Jump ahead to quick start DS24/DS26 and DS26 Features ............................................................v 1 Introduction ..............................................................................vi 2 What is a Speaker Management System? ..........................................1 2.1 Crossover: ..............................................................................1 2.2 Equalization: ...........................................................................1 2.3 Delay: .................................................................................1 2.4 High Pass and Low Pass Filters: ................................................1 2.5 Limiting: .................................................................................1 3 Front Panel .................................................................................2 4 Rear Panel .................................................................................3 5 Quickstart .................................................................................4 6 Installation .................................................................................6 6.1 RACK MOUNTING ..................................................................6 6.2 CONNECTORS ........................................................................6 7 OPERATION .................................................................................7 7.1 Navigating Front Panel Controls...................................................7 7.1.1 Hints for Operation: ......................................................7 7.2 SUBMENUS ...........................................................................8 7.2.1.1 Crossover Submenu ...................................................8 7.2.1.2 Load a Xover: ............................................................8 7.2.1.3 Design a Xover; .........................................................8 7.2.1.4 Store a Xover: ............................................................8 7.2.1.5 Erase a Xover:............................................................8 7.3 Security Submenu.....................................................................8 7.4 Subsystem Submenu ...............................................................9 7.5 Interface Submenu ..................................................................10 7.6 Parameter..............................................................................10 7.6.1 Gain: ........................................................................10 7.6.1.1Inputs: .....................................................................10 7.6.1.2Outputs: ..................................................................10 7.6.1.3Polarity: ..................................................................11 7.6.1.4 Delay: .....................................................................11 7.6.1.5 HPF: .....................................................................11 7.6.1.6 LPF:........................................................................11 7.6.1.7 PEQ: .....................................................................12 7.6.1.8 Limiter: ..................................................................12 7.6.1.9 Name of channel: ......................................................13 7.6.1.10 Input Signal:............................................................13 7.7 DS26 BLOCK DIAGRAM .........................................................14 7.8 DS24 BLOCK DIAGRAM .........................................................16 8 Graphical User Interface (GUI).........................................................17 8.1 MINIMUM SYSTEM REQUIREMENTS .......................................17 8.2 INSTALLING SYSOMAX ON YOUR COMPUTER ........................17 ii ® CONTENTS 8.3 STARTING UP SYSOMAX ......................................................18 8.3.1 From the Start menu: ...................................................18 8.3.2 From Windows Explorer or My Computer: ........................18 8.4 Navigating SYSOMAX ............................................................18 8.4.1 Crossover Types DS24 ................................................19 8.4.2 Crossover Types DS26 ................................................19 8.4.3 Top Line Menu ............................................................20 9 Creating a Program ........................................................................22 9.1 GAINS: ..............................................................................22 9.2 DELAYS: ..............................................................................22 9.3 LIMITERS: ...........................................................................22 9.4 OUT 1, OUT 2, etc. ...............................................................23 9.5 Crossover Filters: ..................................................................23 9.6 Parametric Equalizers: ............................................................23 10 SPECIFICATIONS ........................................................................25 11 Service ..............................................................................26 12 Warranty ..............................................................................26 13 Maintenance ..............................................................................27 IMPORTANT !BEFORE YOU BEGIN, PLEASE CHECK THE CONTENTS WITHIN THIS BOX TO INSURE THESE ITEMS ARE INCLUDED: 1. The BBE DS24/DS26 or DS26 Digital Speaker Processor. 2. The BBE DS24/DS26/DS26 Digital Speaker Processor User's Manual. 3. Power cord. 4. Warranty registration card. 5. Software Disc 6. DB-9 type serial cable for connection between unit and PC. If any of these items are found to be damaged or missing, immediately contact the BBE dealer you purchased it from. This manual will help you to effectively utilize the BBE DS24/26. Reviewing the information contained in this manual will answer most of the common questions that our service department receives. If you still have questions, please feel free to call 800-233-8346. iii DS24/DS26 AND DS26 FEATURES Crossovers Parametric Equalizers Driver Alignment Delay Speaker Protection limiter 10 user memories · Choice of 2 X2-way, 2 X 3-way, 2-way + sub, 4-way, 5-way 6-way crossover (depending on model) · DS24 is 2 inputs 4 outputs and includes 4 crossover configurations · DS26 is 2 inputs 6 outputs and includes 6 crossover configurations · Input gain control for each channel · Separate crossover controller · 5 band fully parametric equalizer · Driver Alignment Delay for each output up to 7ms · Output gain and phase control · Security lockout to discourage system tampering · RS-232 remote control PC interface (Windows compatible software included) · Each group parametric equalizer has 31 ISO frequencies with + or - 12dB gain · Each group Q value is from 0.5 to 10 and provides Hi shelf · Lo shelf selects function. · Separate limiter with Attack, Hold, Decay and Threshold parameters · High Pass and Low Pass filter available for each channel @ 6 or 12dB slope · Choice of 18dB, 24dB, 48dB Butterworth, Linkwitz-Riley or Bessel frequency response curve · Memory for up to 10 on-board user programs · 8X7 bit input/output precision digital LED meter. · 2X20LCD backlit. LED Display iv ® INTRODUCTION Thank you for choosing the BBE DS24/DS26 Speaker Management System. This product will enable you to obtain the best possible performance from your loudspeaker system. You can also reduce the amount of outboard gear that is required to transport, set-up and operate as part of the sound system. The DS24/DS26 offers many powerful functions. It is highly recommended that you read through this manual before you begin connection and operation. For those that are familiar with this type of device or if you simply can't wait to hear how good your system will sound, a Quick Start section follows on pages 4-5. SOME TERMS THAT WILL BE USED IN THIS MANUAL: Configuration: This refers to a particular group of settings, with the primary parameter being the crossover type. Program: A program is a configuration with either the factory default or a user-created name. Configuration and Program may be used interchangeably, though a configuration must be programmed for a program to exist. Parameter: A component of a setting such as the center frequency of one band of parametric EQ or the attack time of a limiter. WARNING! To prevent possible speaker or amplifier damage, always power-up peripheral devices first, wait 10 seconds, and then turn on the power amplifier. Turn off power amplifier first, then power-down peripheral devices. v WHAT IS A SPEAKER MANAGEMENT SYSTEM? A Speaker Management System uses digital signal processing to accomplish multiple functions that affect the audio signal between the mixer and the power amplifiers. These functions include crossover, equalization, delay, limiting, high-pass and low-pass filtering as well as signal distribution. Programs may be created, selected and edited with the DS24/DS26's front panel controls. However, to create new programs, it is best to use the included free PC software and configure the programs using the graphical user interface (GUI) and a Windows PC. 2.1 Crossover: This function used filters to divide the audio spectrum into multiple bands, such as Highs, Mids, and Lows. When these separate signals are individually amplified and sent to a speaker matched for that range, the result is a much more efficient system with more punch and clarity as compared to system using a two or three-way speaker box with a passive cross-over. The common terms used for two or three-way systems are "bi-amp" and "tri-amp". 2.2 Equalization: This function provides control of the tonal spectrum. It can be used to compensate for differing acoustic conditions, speaker cabinet responses or boosting/cutting certain frequency ranges to create a specific type of sound. In some rooms, "ringing" or feedback is present due to a number of conditions. Use the PEQ function to reduce the ringing frequencies. 2.3 Delay: This function is used to "time-align" the different transducers in a speaker system. A properly aligned system will have better phase coherence resulting in more focused sound. 2.4 High Pass and Low Pass Filters: These are used to reduce any signal outside of the desired bandwidth and are part of the equalization function. This frees the power amps and speakers from trying to reproduce signals that are not an intended part of the mix or simply beyond the reproduction range of the loudspeakers. 2.5 Limiting: This function prevents a signal from exceeding a certain pre-determined level. It prevents input overload with its resultant distortion and also keeps amplifiers from clipping, which protects the speakers. 1 ® FRONT PANEL 1. LCD The 2x20 backlit LCD displays the program and programming choices of the unit. 2. These buttons allow navigation for selection of sub-menus and some parameter values. 3. Menu This is one of two buttons that will access the front panel programming. This one is used primarily to select which program to call up, edit or save. 4. Gain This is one of two buttons that will access the front panel programming. This, along with the buttons, accesses the various parameters of a program. 5. Quit This exits the programming menu and returns the display to showing the selected program. 6. Enter Hitting this button will write the current selection to memory. 7. Param This acts as the value selection dial when selecting certain parameters or values for certain parameters (such as Gain). It is both a dial and a button. DO NOT PRESS IN WHEN ROTATING OR THE VALUES MAY NOT TRACK CORRECTLY. 8. Meters These display the respective input and output levels of the device. The seven LED segments per display are in 6 dB steps from ­30dbV to ­6dBV, then -3dBV, then Limit (0dBV), then Clip (+8 dBV) 9. Mute Pressing one of these buttons will mute the respective Output channel and the LED will illuminate. All outputs will mute automatically during certain program selection and editing processes, to protect the loudspeakers. 10. Power This turns the power to the unit On and Off. Remember to always turn power amps on last after everything else and turn them off first, before everything else. 2 REAR PANEL 1. Power Jack This accepts a standard IEC type AC bayonet plug. 2. RS232 Interface Connect this to the serial port on a PC using the included cable or other standard DB-9 type cable. With the software installed, the PC can now monitor and program the DS24/DS26. 3. XLR Input These are balanced (Pin 2 Hot) XLR inputs that accept the signal from the (usually main) outputs of the mixer. 4. XLR Output These are balanced (Pin 2 Hot) XLR outputs. Depending on the model, there will either be 4 or 6 outputs. 3 ® QUICK START NOTE: This section will describe navigation of the front panel controls as follows: The button to press will be shown in ALL CAPITALS. For QUICK START, a number following in parentheses (#) will also be included. These refer to the same names and numbers as shown in Figure 1, Front Panel Controls and Indicators. The expected display text is shown in "quotation marks". If you press a button and the display does not change, it means that the button has no effect for that particular menu item. If you get to a certain point in the menu and want to go back, but cannot, press QUIT (5) and begin the steps again. This is normal for the unit. 1. Before hooking up the system, make sure that all items are OFF, especially the power amps. 2. Use high quality balanced XLR mic cables to make the connections. The feeds from the DS24/DS26 at "front of house" can also be sent through the audio snake returns to the amp stacks if used in a live setting. 3. You should know the frequency response and limits of your loudspeakers 4. Connect the main output or outputs of your mixer to the inputs of the DS24/DS26. 5. Depending on the configuration you select, connect the appropriate number of outputs from the DS24/DS26 to your power amp inputs. 6. Turn on the DS24/DS26. 7. After a brief start up, the display will show "2 x 2 WAY X-OVER" 8. Press MENU (3). Press ENTER (6). Press NEXT (2) "Design a Xover" 9. Press ENTER (6). Select the crossover mode desired with either the BACK/NEXT (2) buttons or the Parameter dial. After selection, Press ENTER (6). 4 QUICK START Depending on the mode selected, other options will appear for this level of the menu, primarily concerned with input and output assignments. Some assignments are fixed with the crossover type selected. Only those assignments that can be selected will show on the display. Either the BACK/NEXT (2) buttons or the Parameter dial will work for stepping through the selections. 10. Press GAIN (4). Set the gain for Input: A. Press NEXT (2) and set the gain for Input B. Gain value is selected with the PARAMETER dial (7). Press NEXT (2) again. 11. You are now in the Output programming section. Depending on the configuration selected, the different outputs will show in the upper left corner of the display as OP1, OP2, etc. You can select an output and then step through the parameters of with the BACK/NEXT (2) buttons OR use the GAIN (4) button to step through the outputs, changing the same parameter for each output as it is displayed and cycle through the outputs for each parameter. 12. Use the PARAM dial (7) to select values. In the Filter and PEQ screens, multiple parameters are displayed simultaneously. To toggle between these, press the PARAM dial (7). In the PEQ screen, the ENTER (6) button is used to toggle between PEQ "", Low Shelf "}", Hi Shelf "{", and Bypass "=" 13. After completion of the patching and programming, power up the rest of the system and enjoy improved sound quality. 14. Practice "safe sound". 5 ® INSTALLATION Your DS24/DS26 was carefully packed at the factory and the packaging was designed to protect the unit from rough handling. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage that may have occurred in transit. If the unit is damaged please do not return it to us but notify your dealer and the shipping company immediately, otherwise claims for damage or replacement may not be granted. Shipping claims must be made by the consignee. 6.1 RACK MOUNTING The DS24/DS26 fits into one standard 19" rack unit of space. Please allow at least an additional 4" depth for the connectors on the back panel. Though this device does not generate significant heat, be sure that there is enough air space around the unit for cooling. To avoid overheating, do not place the DS24/DS26 in rack above devices that generate significant heat such as power amplifiers. 6.2 CONNECTORS The DS24/DS26 must be installed using standard 3 ­pin type XLR jacks. Although the inputs are fully balanced, the automatic servo-functions allow them to operate with unbalanced source/loads. Audio outputs also use XLR jacks. PIN 1 = Ground PIN 2 = HOT (+) PIN 3 = COLD (-) 6 OPERATION There are two methods of creating and selecting programs on the DS24/DS26. 1.The first method uses the front panel controls of the unit and requires stepping through menus to access the proper parameter that needs adjusting. Once programs have been saved to the onboard memory, calling up a program is quite simple. See QUICK START on page XX for an example of navigating and programming a program. 2.The second method uses the included Graphical User Interface (GUI) software run on a Windows PC. The computer connects to the DS24/DS26 and gives a more global view of the parameters and the choices for settings. This is the most efficient method to create the programs you use most and want to save to memory on the unit. They can then be called up as needed. If an adjustment is required and it is not convenient to hook up a PC, the edits can be made from the front panel controls of the unit. NOTE: More detailed descriptions of how the various functions work are in Section 8, Creating A Program. 7.1 Navigating Front Panel Controls There are six buttons and a cursor dial/pushbutton on the front panel, as well as mute buttons for each of the outputs. In conjunction with the display, the six buttons and dial let you create, edit, save, recall and delete programs as well as set security levels as to how much access to the programming menus is available to multiple users. When the unit powers up, it will display the currently selected program by showing either the crossover type or a name for that program that has been saved. 7.1.1 Hints for Operation: The MENU and GAIN buttons access the different levels of the available selections. MENU is used to access submenus for Crossover, Security, Subsystem and Interface. GAIN is used to access specific parameters for a configuration NOTE: In some sub-MENU items, the arrow keys OR the Cursor Dial will select different parameter values. In the parameter menus, the PARAM dial pushbutton allows you to toggle between multiple parameters displayed on a screen. If you get to a spot where you need to step back and the BACK button will not step 7 ® OPERATION you back, simply hit EXIT and start again. Where an additional "ENTER" press is required to write the selection to memory, the screen will prompt you with "[ENTER] to Confirm". The LED display also offers some hints. Left or right arrows on the top line indicate the BACK/NEXT buttons will step to other choices. 7.2 SUBMENUS 7.2.1.1 Crossover Submenu This menu selects the type of crossover and is the primary submenu to create, recall, delete, and name a program configuration. Press MENU and ENTER to access this submenu. Then use the BACK, NEXT and ENTER buttons to adjust the Xover Submenu. Submenu items include: 7.2.1.2 Load a Xover: This will load a configuration that has already been saved into the memory of the unit. Until you have saved other programs into the unit, only the default value will be available. 7.2.1.3 Design a Xover; Use this mode to select a different type of crossover and set the parameters. Parameters include mode type, stereo connect control, input channel adjustment. 7.2.1.4 Store a Xover: Store all the configuration settings of a X-OVER. The DS24/DS26 will store up to 10 program configurations in user memory locations. (An unlimited number can be stored on a PC or other PC accessible memory.) Each of the 10 programs can have a name containing up to 16 letters and numbers. If the program name is not edited, it is stored under the corresponding mode name, such "2 x 2 WAY XOVER". 7.2.1.5 Erase a Xover: This will delete a stored mode. 7.3 Security Submenu This menu allows you lockout various combinations of any or all front panel programming functions. A four-character password is created by the primary user and entered using the PARAMETER dial. To unlock the system, the password must be re-entered. 8 OPERATION Press MENU, NEXT and ENTER. Then use the NEXT/BACK and ENTER buttons to adjust the Security Submenu. The various locking modes are as follows: 1.LOCK: Changes only: Parameters can be viewed, but cannot be adjusted. MUTE buttons are valid. 2.LOCK: Changes + View: Parameters cannot be viewed or adjusted. MUTE buttons are valid. 3.LOCK: Changes + Mutes: Parameters can be viewed, but cannot be adjusted. MUTE buttons are not valid. 4.LOCK: Everything: Parameters cannot be viewed or adjusted. MUTE buttons are not valid. Once a security mode is selected, press ENTER. You will be prompted to enter a security code. This can be from one to four characters. Any of the characters available from the on-board selection choices may be used. A.Press the BACK/NEXT buttons to shift the cursor to one of the four positions. Then rotate the PARAM dial to select the desired character (letter, number or symbol). B.Press ENTER, confirm the password and display as follows: C.Repeat procedure A and press ENTER. D.The system is locked when the reentered password matches the original entry otherwise the locking operation is invalid. If invalid, the screen will show "Locks Not Set!! Bad Confirmation". If the codes match, the screen will show "Locking Unit". Though up to four characters may be used, the lock out will work with just a single character. The initial and confirming entry must both be in the same position. If nothing is entered (all blanks) the unit will still lock. 7.4 Subsystem Submenu This menu allows selection of Input Linking; a "wake up time" fade in or Mute Hold; and the method for displaying delay: Time, Meters or Feet. Press MENU, NEXT and NEXT again. Then use the BACK/NEXT and ENTER buttons to adjust the Subsystem Submenu. Subsystem Submenu items are as follows: 1.Input option: Determines whether the A and B inputs are linked or separate. 2.Wake up time: 9 ® OPERATION A.Determines whether the outputs will stay muted on power up until manually switched off (Mute Hold) or the level will gradually fade up to the operating level (Fade In). The fade-in time is fixed. B.Fade-in: Mutes are off, but Output channels rise to programmed levels gradually. C.Mute Hold: All Output channels are muted until the mutes are manually disabled either on the front panel or through the GUI. 3.Delay Time/Distance: Selects the Delay unit display for either Time, Meters, or Feet NOTE: Though there are some variables, generally speaking the speed of sound in 71 degree Fahrenheit dry air at sea level is ~773miles per hour. This is ~345 meters per second and about 1.13 feet per millisecond. .5 milliseconds equates to about 6.78 inches. 7.5 Interface Submenu This submenu deals with the PC interface and includes setting for baud rate and ID number. Press MENU, then NEXT three times and then ENTER twice. Use the BACK/NEXT and ENTER buttons to adjust the Subsystem Submenu. The PARAM dial may also be used to enter values. Subsystem Submenu items are as follows: 1.RS232 baud rate and address code setting: Select 2400, 4800, 9600, 19200, 38400 baud rate according to different PC capabilities. 2.Remote ID NUM: Select 1~32. Use this function when multiple DS24/DS26 units are used. Master Control unit is set as 1; slave units are set with subsequent numbers. 7.6 Parameter Parameter lets you set the specific values for a configuration. Generally these are set for the outputs of the device. Inputs require only a gain setting. Parameters include such things as polarity, EQ, Limiter, Delay, HiPass Filter, LoPass Filter, and Filter Type. 7.6.1 Gain: The first two presses of the GAIN button will offer Input Level adjustment for A and B. The third press takes you to the Outputs. Once in Outputs, additional presses of GAIN will cycle you through the four or six outputs. (The system will display the last Output selected from the previous editing session.) 7.6.1.1 Inputs: Press GAIN to enter the Parameter setup menu. Set the gain for Input A using the PARAM dial. Press NEXT and set the gain for Input B using the PARAM dial. 10 OPERATION 7.6.1.2 Outputs: Press NEXT again and the screen will display an Output (Op1 = Output 1). Set the desired input gain level. At this point you can use the BACK/NEXT buttons to step through each of the parameters for the currently selected output. Press the GAIN button again to go to the next Output and program all of its parameters. (The GAIN button will now select only the Output channels; the gain adjustment screens for the Inputs will not be displayed unless you exit the menu and start again.) Each Output will have both a number and name displayed. The names are taken from a default list with labels such as Low, Mid, Highs, Sub, etc. An alternate method is to program a single parameter for Output 1, such as DELAY, then press the GAIN button to go to each of the Output channels in turn and program the delay parameter for that channel. Now select the next parameter and program that for each of the outputs in sequence. In some cases this may make it easier to keep track of the comparative values between outputs. For simplification, we will follow though programming all the parameters for a single output. Set the Gain for Output 1. Range is ­40 dB to + 6 dB 7.6.1.3 Polarity: Set the polarity for Output 1. Switching this will change the phase of the signal 180 degrees. 7.6.1.4 Delay: Set the Delay time for Output 1. Delay is used to align drivers in a stack that may be in different vertical planes. Delay range is 0ms to 7ms selectable in .5 ms increments. 7.6.1.5 HPF: This is part of the crossover function. Sets the "knee" (corner frequency) and filter slope type for the HiPass Filter (HPF). Frequencies below the selected frequency will be filtered by the selected filter type and slope. Press the PARAM dial to toggle between these two parameters on the display. 7.6.1.6 LPF: Set the "knee" (corner frequency) and filter slope type for the LoPass Filter (LPF). Frequencies above the selected frequency will be filtered by the selected filter type and slope. Press the PARAM dial to toggle between these two parameters on the display. 11 ® OPERATION HiPass: frequency range 10Hz~16.0KHz LoPass: frequency range 35Hz~22.0KHz Use HPF and LPF together to define the frequency band for this channel of the crossover. 7.6.1.7 PEQ: Set the parameters for the five available bands of parametric EQ. Press the PARAM dial to toggle between the three parameters on the display. These include Frequency, Q and Cut or Boost. Pressing the ENTER button in this mode will select the symbol in the upper right corner. Depending on other settings, the choices will include some or all of the following: means PEQ means Lo shelf means Hi shelf means PEQ bypass Q is 0.5 to 10 and Hi Shelf or Lo Shelf. NOTE: when using Hi shelf or Lo shelf, set Gain=0.0dB, change Q-value to Hishelf/Loshelf. } { = (PEQ), } (Lo shelf), { (Hi shelf), = (PEQ bypass) The choices for the PEQ center frequencies are 31 ISO frequencies between 20 Hz and 20 kHz. Gain is +/- 12 dB 7.6.1.8 Limiter: The limiter is used to limit the signal going to the output stage and ultimately the amps, to a predetermined maximum level, with the intention of preventing clipping and its resultant distortion. There are four parameters available to set for the Limiter The signal BEFORE gain control and AFTER limiter processing 1.Input Level sets the point at which the limiting circuitry will activate. This is sometimes referred to as Threshold. The range is -20dBV to +15dBV. A lower input level will activate the limiter sooner, affording more protection, but possibly creating more sonic artifacts if the limiter is activating and deactivating too frequently. Ideally, the limiter should be set so that it activates occasionally on peaks in the program. This control is also tied to the front panel level display meter for its selected output. As you lower the Limiter input level, the sensitivity of the meter will increase. This means a lower input level will result in the same signal showing more level on the Output channel display. Ideally, the output level should just approach and occasionally cross into limiting. 2.Attack. This is the amount of time that elapses before the limiter reduces the 12 OPERATION gain to the program level after the threshold point has been exceeded by the incoming signal. Generally, set shorter attack times on outputs that are feeding mids and highs and longer attack times for lows and subs. The time should be chosen carefully as the danger of dynamics distortion usually increases with shorter attack times. The attack time of the DS24/DS26 can be set within a range of 1 to 100 milliseconds. 3.Hold determines how long the limiter's gain reduction stays in place, even after the input signal has fallen below the Threshold. Use this to smooth out "choppiness", "pumping" or other artifacts that may occur under certain settings and program material. The hold time of the DS24/DS26 can be set within a range of 0.0 to 1000 milliseconds in 10ms increments. 4.Decay [should be "Release"]This control determines the how quickly the limiter removes the gain reduction and returns the signal to unity gain once the input signal has fallen below threshold. In instances where the limiter is constantly and repeatedly activated, a longer Decay time will prevent excessive retriggering and provide a more consistent signal. This control can be adjusted from 10ms to 1000ms in 10ms increments. 7.6.1.9 Name of channel: This function allows you to choose a name or label for an output channel. There is a fixed list of 32 choices to choose from. Use the PARAM Rotate to change the channel name. 7.6.1.10 Input Signal: In this menu, LCD displays the current input channel for the selected output. This parameter cannot be adjusted, but can be checked for set-up and monitoring purposes. 13 ® BLOCK DIAGRAMS 7.7 DS26 BLOCK DIAGRAMS GAIN HPF LPF PEQS Delay GAIN MUTE LOW OUTPUT 1 INPUT A HPF SUM A+B LPF PEQS Delay GAIN MUTE HIGH OUTPUT 2 INPUT B GAIN HPF LPF PEQS Delay GAIN MUTE LOW OUTPUT 3 HPF LPF PEQS Delay GAIN MUTE HIGH OUTPUT 4 HPF LPF PEQS Delay GAIN MUTE Msub OUTPUT 5 HPF LPF PEQS Delay GAIN MUTE DS26 2X2 WAY + SUM Aux OUTPUT 6 INPUT A GAIN HPF LPF PEQS Delay GAIN MUTE LOW OUTPUT 1 HPF LPF PEQS Delay GAIN MUTE HIGH OUTPUT 2 HPF LPF PEQS Delay GAIN MUTE LOW OUTPUT 3 INPUT B GAIN HPF LPF PEQS Delay GAIN MUTE HIGH OUTPUT 4 HPF LPF PEQS Delay GAIN MUTE Msub OUTPUT 5 DS26 2X3 WAY HPF LPF PEQS Delay GAIN MUTE Aux OUTPUT 6 14 BLOCK DIAGRAMS INPUT A GAIN HPF LPF PEQS Delay GAIN MUTE MUTE LOW OUTPUT 1 HIGH OUTPUT 2 LOW OUTPUT 3 HPF LPF PEQS Delay GAIN MUTE MUTE SUM A+B HPF LPF PEQS Delay GAIN MUTE MUTE INPUT B GAIN HPF LPF PEQS Delay GAIN MUTE MUTE HIGH OUTPUT 4 HPF LPF PEQS Delay GAIN MUTE MUTE MSUB OUTPUT 5 OUT 5 & 6: B OUT 5 & 6: A+B HPF LPF PEQS Delay GAIN MUTE MUTE AUX OUTPUT 6 DS26 4 WAY + 2 AUX INPUTA GAIN HPF LPF PEQS Delay GAIN MUTE MUTE LOW OUTPUT 1 HIGH OUTPUT 2 LOW OUTPUT 3 HPF SUM A+B LPF PEQS Delay GAIN MUTE MUTE HPF LPF PEQS Delay GAIN MUTE MUTE INPUTB GAIN HPF LPF PEQS Delay GAIN MUTE MUTE HIGH OUTPUT 4 HPF LPF PEQS Delay GAIN MUTE MUTE MSUB OUTPUT 5 DS26 5 WAY + 1 AUX INPUT A OUT 6:B OUT 6:A+B HPF LPF PEQS Delay GAIN MUTE MUTE AUX OUTPUT 6 GAIN HPF LPF PEQS Delay GAIN MUTE LOW OUTPUT 1 HIGH OUTPUT 2 LOW OUTPUT 3 HPF LPF PEQS Delay GAIN MUTE HPF LPF PEQS Delay GAIN MUTE HPF LPF PEQS Delay GAIN MUTE HIGH OUTPUT 4 HPF LPF PEQS Delay GAIN MUTE MSUB OUTPUT 5 DS26 6 WAY HPF LPF PEQS Delay GAIN MUTE AUX OUTPUT 6 15 ® BLOCK DIAGRAMS 7.8 DS24 BLOCK DIAGRAMS INPUT A GAIN HPF LPF PEQS Delay GAIN LIMITER CLIP MUTE LOW OUTPUT 1 HIGH OUTPUT 2 HPF LPF PEQS Delay GAIN LIMITER CLIP MUTE SUM A+B GAIN HPF OUT 3 & 4: B OUT 3 & 4: A+B LPF PEQS Delay GAIN LIMITER CLIP MUTE LOW OUTPUT 3 HIGH OUTPUT 4 INPUT B DS24 2X2 WAY INPUT A GAIN HPF LPF PEQS Delay GAIN LIMITER CLIP MUTE HPF LPF PEQS Delay GAIN LIMITER CLIP MUTE