TABLE OF CONTENTS iMove 250W Moving Wash 1.Safety Instruction 2.Technical Specification 3.Lamp 4.How To Set The Unit 4.1 Control Panel 4.2 Main Function 4.3 Home Position Adjustment 5.How To Control The Unit 5.1 Master/Slave Built-In Preprogrammed Function. 5.2 Easy Controller 5.3 iSolution Operation / DMX Controller 5.4 DMX512 Configuration 5.5 DMX512 Connection 6.Troubleshooting 7.Fixture Cleaning User Guide BEGLEC cva ­ `t Hofveld2 ­ 1702 Groot Bijgaarden Belgium WWW.BEGLEC.COM 1- 1. Safety Instruction Please read carefully the instruction, which includes important information about the installation, usage and maintenance. WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Unpack and check carefully there is no transportation damage before using the unit. Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit. The unit is designed for use with the MSD 250/2 or NSD250/2. Do not use any other type of lamp. It's important to ground the yellow/green conductor to earth in order to avoid electric shock. The unit is for indoor use only. Use only in a dry location. The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked. Disconnect main power before fuse/lamp replacement or servicing. Replace fuse/lamp only with the same type. Make sure there are no flammable materials close to the unit while operating, as it is fire hazard. Use safety chain when fixes this unit. Don't handle the unit by taking its head only, but always by taking its base. Maximum ambient temperature is Ta : 40. Don't operate it where the temperature is higher than this. Unit surface temperature may reach up to 85. Don't touch the housing bare-hand during its operation, and allow about 15 minutes to cool down before replacing bulb or serving, as the unit could be very hot. In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts. Warning To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. Never touch bulb with bare fingers, as it is very hot after using. Hot lamp explosion hazard. Do not open the unit within five minutes after switching off. Do not start on the unit without bulb enclosure or housing are damaged. The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. Do not look directly at the light while the bulb is on. Caution There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer. Installation The unit should be mounted via its mounting system ( as shown below ) on the bottom of the base. Use clamps to fix the unit to truss. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 30 kgs for each unit. Don't connect the device to any dimmer pack. Do not touch any wire during operation as high voltage might be causing electric shock. 23- 2. Technical Specification Power supply - AC 120V ~ 60Hz / 230V ~ 50Hz Lamp - Discharge lamp MSD 250/2 GY 9.5 Optical system - High efficiency optical system - High quality optical lens and dichroic colors - Manually adjustable beam angle: 16 ~26 Shutter/Dimmer - Blackout, 0~100 smooth dimming and strobe speed variable(1~10 flashes per second). Color wheel - Independent color wheel with 6 dichroic colors plus white. - Color wheel rotates with variable speed, giving rainbow effect. CMY Mixing system - Cyan: 0 ~ 100%, Magenta: 0 ~ 100%, Yellow: 0 ~ 100% Effect Wheel - Frost filter and beam shape effect Movement - Pan: 540° in 2.8 second. - Tilt: 270° in 1.6 second. DMX Channels - Standard DMX512 signal addressing and can be controlled by any universal DMX controller. 16 Channels: Channel 1 = Pan Channel 2 = Tilt Channel 3 = Pan/Tilt Speed Channel 4 = Dimmer Channel 5 = Shutter Channel 6 = Color Channel 7 = Cyan Channel 8 = Magenta Channel 9 = Yellow Channel 10 = CMY color Mix Channel 11 = CMY Speed Channel 12 = Effect Wheel Channel 13 = Dimmer Channel 14 = Pan 16 bit Channel 15 = Tilt 16 bit Channel 16 = Lamp On/Off/Reset 8 Channels: Channel 1 = Pan Channel 2 = Tilt Channel 3 = Shutter Channel 4 = Effect wheel Channel 5 = Color Channel 6 = CYM Color Mix Channel 7 = Dimmer Channel 8 = CMY Speed Dimension: 428 x 369 x 481 mm (L x W x H) Weight: 24.2 kg Luminous intensity: 4- 5- 3. Lamp In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off. Because of its high internal pressure, there might be a risk that the Discharge lamp would explode during operation. The lamp emits intense UV radiation which is harmful to the eyes and skin. The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp. Discharge lamp: MSD 250/2 GY 9.5 4. How To Set The Unit 1. Always switch off the main supply and never handle the lamp or luminaries when is hot. 2. Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation. 3. The lamp generates UV radiation. Never operate the lamp without appropriate shielding. 4. When burning, the lamp operates at high pressure and there is a slight risk of arc tube rupture. The risk increases with age, temperature and improper handling of the lamp. Do not use the lamp any longer than its specified life. 5. Make sure the lamp is located in the center of the reflector for the best spot. Adjust lamp position by screws A, B and C. 4.1. Control Panel Display To show the various menus and the selected functions . LED DMX MASTER SLAVE SOUND Button 67On On On Flashing DMX input present Master mode Slave mode Sound activation MENU DOWN UP ENTER Remote controller input To select the programming functions To go backward in the selected functions To go forward in the selected functions To confirm the selected functions 4.2. Main Function To select any of the pre-set functions, press the MENU button up to when the required one is shown on the display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to change the mode. Once the required mode has been selected, press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds. To go back to the functions without any change press the MENU button. The main functions are shown below: DMX512 Address Setting Setting 16 Channel Setting 8 Channel Show mode 1 Show mode 2 Show mode 3 Show mode 4 Slave Mode " Normal " Slave mode " 2 Light Show " Blackout Mode " Yes Blackout " Blackout Mode " No Blackout " Pan Normal Pan Inversion Tilt Normal Tilt Inversion LED on LED off Display Normal Display Inversion Self-Test Ambient temperature of lamp Fixture Hours Lamp on Lamp off Reset By connecting to the 1/4" microphone jack to control the unit for Stand by, Function, and Mode function. Sensitivity To adjust the sound-receiving sensitivity . Microphone To receive audio signal for sound activation . DMX input/output For DMX512 link, use 3-pin XLR plug cable to link the unit together. MENU DMX512 Address Setting Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions 8without any change press the MENU button again. 9- Channel Mode Press the MENU button up to when the Channel ) or is shown on the display. Pressing ENTER (16 Blackout Mode Press the MENU button up to when the blackout) or is shown on the display. Pressing ENTER (yes button and the display will blink. Use DOWN and UP button to select the button and the display will blink. Use DOWN and UP button to select the (8 Channel) mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Show Mode Press the MENU button up to when the or (show 2) or (show 3) or is showing on the display. Pressing ENTER (show 1) (show 4) mode. Once the mode has (no blackout) mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Pan Inversion Press the MENU button up to when the or is shown on the display. Pressing ENTER (normal) button and the display will blink. Use DOWN and UP button to select the button and the display will blink. Use DOWN and UP button to select the been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. (pan inversion) mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Tilt Inversion Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°. Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°. Show 3 mode - Fixture is placed on the speaker, The spot is always projecting to the audience's direction; i.e in front of the stage. Pan movement angle ( left to right to left ): 160°. below horizon.) Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in front of the stage. Pan movement angle ( left to right to left ) :160°. Tilt movement angle: 90° ( vertically, front 75°; back 15° ) Slave Mode Press the MENU button up to when the is shown on the display. Pressing ENTER (normal) Tilt movement angle: 90° ( 60° above horizon; 30° Press the MENU button up to when the or is shown on the display. Pressing ENTER (normal) button and the display will blink. Use DOWN and UP button to select the (tilt inversion) mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Led Display Press the MENU button up to when the (Led on) or is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (Led off) mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Display Inversion It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to when the is blinking on the display. Use the ENTER button to change to the mode 11- button and the display will blink. Use DOWN and UP button to select the (2 light show) mode. Once the mode has been selected, press the ENTER or button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. 10- (display inversion), It will automatically store after 8 seconds. Or press the ENTER button again return to the mode the MENU button. Display normal mode for the fixture putting on the floor. Display inversion mode for the fixture fixing under ceiling. (display normal). To go back to the functions press Set DMX value of channel 8 and channel 16 to 255, then all channels of the unit will return to their standard home position. 4.3 Home Postion Adjustment Press MENU button for at least 5 seconds into offset mode to adjust the home position, the functions are shown below: Self-Test Press the MENU button up to when the MENU button again. Ambient temperature of lamp Press the MENU button up to when the functions press the MENU button again. Fixture Hours Press the MENU button up to when the functions press the MENU button again. Lamp Display Press the MENU button up to when the or is blinking on the display. Pressing ENTER (Lamp on) is blinking on the display. Pressing ENTER is blinking on the display. Pressing ENTER Pa ...