User manual BEITER WH

Update 01/2004 The WING-HOLDER The Beiter Wing-Holder is designed to position and fletch vanes (e.g. Spin WingsTM, Rite FliteTM, Kurly VanesTM...) easily and precisely on arrow shafts. It is available for Right-hand (RH) and Left-Hand (LH), and for vane lenght 1-3/4" only. The Beiter Wing-Holder comes with a Bushing, which allows off-set of the vane by 1°. pic. 1 pic. 2 pic. 3 HOW TO PREPARE THE VANE Clean the arrow shaft with acetone (before installing the nock!) Draw the necessary lines with the Beiter Tri-Liner. Insert the vane in the Beiter Wing-Holder (Pic.2) and align it with the edge as shown in Pic.3. Strip off the first layer of the tape as much as needed and hold it down in one of the grooves on the back of the Beiter Wing-Holder. - Pic.4 Turn the Beiter Wing-Holder and position the tape along the edge of the vane. Pic.5 Press on the tape. Than cut the useless parts of the tape on both sides with scissors or a knife. - Pic.6 Hint: Prepare more vanes ready to be fletched on more Wing-Holders and keep them safe in your quiver or bowcase. You will have one or more spare vanes ready to use! HOW TO FLETCH THE VANE Strip off the second layer of the tape, so the fletching surface is free. Put the Beiter Wing-Holder on the arrow shaft, so that both pins are in contact with the shaft. Don't let the tape have contact with the shaft. Align the Beiter Wing-Holder along the drawn line, using the three positioning sectors placed along the vane edge. - Pic.7 Note: Place the vane in the correct direction on the shaft, as shown on the Beiter Wing-Holder (Nock - Point) - Pic.1 Pay attention to place the vane along the drawn line and not on it! The tape won't hold on the line. Now press the Beiter Wing-Holder on the shaft. Than release the pressure completely and turn away the shaft from the Beiter Wing-Holder. - Pic. 8 Eventually press the vane Code# Description on the shaft with your Tri-Liner thumb on the medium TL7503BL Tri-Liner, Blue, complete sector (should not be Wing-Holder necessary, if the shaft has TL76643RBLGE Wing-Holder, RH, Set of 3 been cleaned well!). TL7664RBLGE Wing-Holder, RH You may fletch your vanes straight (parallel to the drawn line) or 1° off-set: simply install the red bushing delivered with the Beiter Wing-Holder over the front pin (Point>), by pressing it in. Pic. 9 TL76643LBLGE TL7664LBLGE NA1 NA2 TL7631RT TL99001 TL99002 TL99003 TL99004 TL99005 TL99006 TL99007 pic. 4 pic. 5 BEITER TRI-LINER & WING HOLDER pic. 6 pic. 7 pic. 8 pic. 9 Wing-Holder, LH, Set of 3 Wing-Holder, LH Single Spare Parts Nockadapter for Nockbed #1, Black Nockadapter for Nockbed #2, Orange Tri-Liner, Tags, Red Tri-Liner, Ruler (Arm), Blue Tri-Liner, Segment (1/3), Blue Tri-Liner, Body, Blue Tri-Liner, Ring, Grey Tri-Liner, Cover, Blue Tri-Liner, Indicator, Red Tri-Liner, Screw Tel. +49 7720 856860 Fax +49 7720 4238 email: info@wernerbeiter.com Werner Beiter Daimlerstr. 18 DE-78083 Dauchingen www.WernerBeiter.com