FP93G/FP93GX LCD Color Monitor 19.0" LCD Panel Size User's Manual Welcome i Copyright Copyright © 2005 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation. ii Disclaimer BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ Corporation to notify any person of such revision or changes. Please follow these safety instructions for best performance, and long life for your monitor iii Power Safety · The AC plug isolates this equipment from the AC supply. · The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet should be installed near the equipment and be easily accessible. · This product should be operated from the type of power indicated on the marked label. If you are not sure of the type of power available, consult your dealer or local power company. iv Care And Cleaning · Cleaning. Always unplug your monitor from the wall outlet before cleaning. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any liquid, aerosol or glass cleaners. · Slots and openings on the back or top of the cabinet are for ventilation. They must not be blocked or covered. Your monitor should never be placed near or over a radiator or heat source, or in a built-in installation unless proper ventilation is provided. · Never push objects or spill liquid of any kind into this product. v Servicing · Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages or other risks. If any of the above mentioned misuse or other accident such as dropping or mishandling occurs, contact qualified service personnel for servicing. 2 i Table of Contents Getting started ...................................................................................................................... 5 Getting to know your monitor ............................................................................................ 6 Front View ...................................................................................................................6 Back View .....................................................................................................................6 How to install your monitor hardware ............................................................................... 7 How to detach the stand base ....................................... 10 Using the Monitor Wall Mounting Kit ....................................................................11 Getting the most from your BenQ monitor ...................................................................... 13 How to install the monitor on a new computer ......................................................14 How to upgrade the monitor on an existing computer ..........................................15 How to install on Windows XP systems ...................................................................16 How to install on Windows 2000, ME, & 98 systems ..............................................18 How to complete the Windows Upgrade Device Driver Wizard ...........................19 How to adjust the screen resolution .................................................................................. 21 How to adjust the screen refresh rate ................................................................................ 22 How to set the picture optimization .................................................................................. 23 How to adjust your monitor .............................................................................................. 24 A Look at the Control Panel .....................................................................................24 Hot Key Mode ...........................................................................................................25 Main Menu Mode ......................................................................................................25 Troubleshooting ................................................................................................................. 33 Frequently Asked Questions (FAQ) .........................................................................33 Need More Help? .......................................................................................................34 Supported operating modes ............................................................................................... 35 Specifications ...................................................................................................................... 36 Table of Contents 3 4 Table of Contents 1 11 Getting started 1 When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement. BenQ LCD Monitor Quick Start Guide CD-ROM Power Cord Signal Cable: D-Sub Signal Cable: DVI-D Getting started 5 1 12 Getting to know your monitor 1 Front View Back View 1. Power AC input jack 2. DVI-D Connector 3. D-Sub Connector 6 Getting to know your monitor 1 13 How to install your monitor hardware 1 If the computer is turned on you must turn it off before continuing. Do not plug-in or turn-on the power to the monitor until instructed to do so. 1. Attach the monitor base. Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls. Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like the monitor packaging bag on the desk for padding. Lay the screen face down on a flat clean padded surface. Whilst holding the monitor firmly against the desk, pull the monitor stand arm upwards clear of the monitor. Orient and align the stand base socket with the end of the stand arm, then push them together until they click and lock into place. Gently attempt to pull them back apart to check that they have properly engaged. Carefully lift the monitor, turn it over and place it upright on its stand on a flat even surface. You should position the monitor and angle the screen to minimize unwanted reflections from other light sources. How to install your monitor hardware 7 2. Connect the video cable. Connect one end of the DVI-D cable to the monitor DVI-D socket and the other end to the DVI-D port on your computer. (optional) The DVI-D format is used for direct digital connection between source video and digital LCD monitors or projectors. The digital video signals produce a superior quality picture than analog video signals. Connect the plug of the D-Sub cable (at the end without the ferrite filter) to the monitor D-Sub socket. Connect the other plug of the D-Sub cable (at the end with the ferrite filter) to the computer video D-Sub socket. Tighten all finger screws to prevent the plugs from accidently falling out during use. 3. Connect the power cable to the monitor. Plug one end of the power cord into the socket labelled `POWER IN' on the rear of the monitor. Do not connect the other end to a power point just yet. 8 How to install your monitor hardware 4. Route the cables via the loose bracket. Release the cable retaining clip by squeezing the clip inwards as illustrated. Position the cables together and reinsert the clip over them to retain the cables neatly in place behind the monitor stand. 5. Connect-to and turn-on the power. Plug the other end of the power cord into a power point and turn it on. Turn on the monitor by pressing the power button on the front of the monitor. Turn on the computer too, and follow the instructions in Section 4: Getting the most from your BenQ monitor to install the monitor software. How to install your monitor hardware 9 How to detach the stand base 1. Prepare the monitor and area. Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable. Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls. Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like a towel on the desk for padding, before laying the screen face down on a flat clean padded surface. 2. Release the locking clip on one side of the stand base whilst pulling the edge of the base away from the stand arm. 3. Release the other locking clip to detach the stand base from the monitor stand arm. 10 How to install your monitor hardware Using the Monitor Wall Mounting Kit The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, please read the precautions carefully. Precautions: · Install your monitor and monitor mounting kit on a wall with flat surface. · Ensure that the wall material is stable to support the weight of the monitor. · Turn off the monitor and the power before disconnecting the cables from the LCD monitor. 1. Remove the monitor base. Lay the screen face down on a clean and well-padded surface. Detach the monitor base as instructed in "How to detach the stand base." 2. Remove the monitor stand. Use a a cross-pointed screwdriver to release the screws that fixing the monitor stand to the monitor. The use of a magnetic-head screwdriver is recommended to avoid of losing the screws. Then pull the monitor stand backward away from the monitor. In case you intend to use your monitor on the stand in the future, please keep the monitor base, monitor stand, and screws somewhere safe for future use. How to install your monitor hardware 11 3. Remove the rear cover. Pull around the edge of the rear cover and slightly lift it to reveal the screw plate at the back of the monitor. 4. Follow the instruction manuals of the wall mount bracket you purchased to complete the installation. To attach the rear cover: 1. Tilt the rear cover forward and insert the two tabs on the front edge into the recesses of the screw plate. No tools are required. 2. Position the two tabs on left side of the rear cover to fit into the grooves in the screw plate. 3. Push the other two tabs on the right side of the rear cover inward so that they could snap into the aligned grooves. There will be a clicking sound as the rear cover is perfectly attached. 12 How to install your monitor hardware 1 14 Getting the most from your BenQ monitor 1 How do I gain the most benefit from my new monitor? To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM. The circumstances under which you connect and install your BenQ LCD Monitor will determine which process you need to follow to successfully install the BenQ LCD Monitor driver software. These circumstances relate to which version of Microsoft Windows you are using, and whether you are connecting the monitor and installing the software onto a new computer (without existing monitor driver software), or whether you are upgrading an existing installation (which already has existing monitor driver software) with a newer monitor. In either case however, the very next time you turn on your computer (after connecting the monitor to your computer), Windows will automatically recognise the new (or different) hardware, and will launch its Found New Hardware wizard. Follow the wizard instructions until it asks you to select a monitor model. At that point, click the Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate monitor model. Further details and step-by-step instructions for both an automatic (new) or upgrade (existing) installation follow. See: · How to install the monitor on a new computer. · How to upgrade the monitor on an existing computer If you require a User Name and Password to login to your Windows computer, you must be logged on as an Administrator or as a member of the Administrators gr ...