OxyProTM USER'S GUIDE 7920 SERIES 220 - 240V 3 Safety Instructions 4 Product View/Accessories 5 Assembly 6-17 Features / Operations 18-20 Routine Maintenance 21 Troubleshooting 22 Consumer Services 23 Replacement Parts 24 Warranty ug310-5829_7920K_405.indd 1 5/5/06 11:25:01 AM Thanks for buying a BISSELL OxyProTM We're glad you purchased a BISSELL OxyPro heated formula deep cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your OxyPro is well made, and we back it with a limited two-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your OxyPro. Thanks again, from all of us at BISSELL. Mark J. Bissell President and Chief Executive Officer 2 ug310-5829_7920K_405.indd 2 5/5/06 11:25:09 AM IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT DEEP CLEANER. Always connect to a properly Earthed Outlet. Unplug from outlet when not in use and before conducting maintenance or troubleshooting. WARNING: To reduce the risk of fire, electric shock, or injury: Use indoors only Do not immerse Use only on surfaces moistened by cleaning process Do not leave machine when it is plugged in Do not service machine when it is plugged in If the supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard Do not use machine if it has been dropped, damaged, left outdoors or dropped into water Do not expose to rain, store indoors Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or edges, run appliance over cord, or expose cord to heated surfaces Do not carry the appliance while in use Do not unplug by pulling on cord. Unplug by grasping plug not the cord Do not handle plug or appliance with wet hands Do not put any object into appliance openings, use with blocked opening, or restrict air flow Do not expose hair, loose clothing, fingers or body parts to openings or moving parts Do not pick up hot or burning objects Do not pick up flammable or combustible materials (lighter fluid, petrol, kerosene, etc.) or use in the presence of explosive liquids or vapour Do not use appliance in an enclosed space filled with vapours given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapours Remove plug from electrical outlet before cleaning or maintaining the appliance Not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, petrol, etc.) Do not modify the Earthed plug Do not allow to be used as a toy Do not use for any purpose other than described in this User's Guide Use only manufacturer's recommended attachments Use only cleaning products formulated by BISSELL for use in this appliance to prevent internal component damage Keep openings free of dust, lint, hair, etc. Keep appliance on a level surface Turn off all controls before unplugging Be extra careful when cleaning stairs Pay close attention when working around children SAVE THESE INSTRUCTIONS. THIS MODEL IS FOR HOUSEHOLD USE ONLY. WARNING: This appliance must be earthed. IMPORTANT FOR OPERATION ON A 220/240 VOLT A.C. 50/60 Hz POWER SUPPLY ONLY. If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp (ASTA approved to BS 1362) fuse is fitted in the carrier contained in the plug. Spares may be obtained from your BISSELL supplier. If for any reason the plug is cut off, it must be disposed of, as it is an electric shock hazard should it be inserted into a 13 amp socket. 3 ug310-5829_7920K_405.indd 3 5/5/06 11:25:09 AM Trigger Keep plenty of genuine BISSELL Advanced Deep Cleaning Formulas on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL Advanced Deep Cleaning Formulas. NonBISSELL cleaning solutions may harm the machine and void the warranty. Upper Handle 3. Power Switch Tank-inTankTM Crevice Tool Storage Belt Storage Tool Caddy Power Cord Quick Release Tough Stain Brush Storage 2. 4. Hex Nuts TurboBrushTM Storage Handle Release SmartTempTM Ready Light SmartMixTM Switch SmartMixTM Bottle 5. 4" Upholstery Tool Storage 1. Flex Hose Lower Handle Perfect PassTM Flow Indicator (Filter Inside) ReadyToolsTM Dial Accessories *All items may not be included with your model. More tools are available. To order replacement parts or tools please refer to page 23. 4" Upholstery Tool Tough Stain Brush PreTreat Wand Bare Floor Attachment DirtLifter PowerBrush TM Spraying Crevice Tool Belt Access Door Floor Nozzle Window ON CTI SU USH BR TurboBrush 4 TM 16 oz. BISSELL Fiber Cleansing FormulaTM with ScotchgardTM Protector 950 ml BISSELL Hard Floor SolutionsTM 14 oz. BISSELL OxyKICTM Carpet Spot & Stain Remover ug310-5829_7920K_405.indd 4 5/5/06 11:25:10 AM How To Use This Guide This User's Guide has been designed to help you get the utmost satisfaction from your BISSELL OxyPro. You'll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this User's Guide thoroughly before assembling your deep cleaner. Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they go. Following this User's Guide will greatly enhance your ability to get the most performance from your BISSELL OxyPro for many years. Your OxyPro comes in 3, easy to assemble components. Upper Handle Lower Handle Tool Caddy The only tool you will need to assemble your cleaner is a Phillips head screwdriver. WARNING: cleaner Do not plug in your until you have completely assembled it per the following instructions and are familiar with all instructions and operating procedures. How To Put It Together Refer to Assembly Diagram on page 4 Slide Upper Handle firmly onto Lower Handle until screwholes are completely aligned. Feed bundled Power Cord through Tool Caddy from Caddy's flat side. Align Upper Handle holes and Tool Caddy holes. 1. 2. 3. 4. 5. 6. 7. 8. Place hex nut into back of Tool Caddy and hold in place. Insert bolt from front to back turning into the hex nut until snug. Do not over tighten. Repeat for the second bolt and hex nut. Insert 2 screws into lower 2 holes. Turn until snug. Snap tools into storage on the Tool Caddy as shown in figure 6. Wrap Power Cord and Flex Hose as shown in figure 7. Insert TurboBrush into storage on Upper Handle by tilting the top of the TurboBrush and snapping it into place. OxyPro assembly is now complete. 7 ON OFF 6 ON OFF 5 ug310-5829_7920K_405.indd 5 5/5/06 11:25:16 AM Special Features of your BISSELL OxyProTM The BISSELL SmartCleanTM System The OxyPro is a home cleaning system that automatically mixes hand hot tap water with BISSELL Advanced Deep Cleaning Formula and heats the solution as it is applied to the carpet. The combination of heated cleaning solution, powered brush and suction provide a safe and effective method of cleaning. SmartTempTM Power Switch Temperature control automatically heats the cleaning solution as it is being applied to the carpet (*) to safely optimize cleaning effectiveness. ON OFF ON OFF 1. The Power Switch controls power to the machine and the SmartTemp feature. *SmartTemp heats the cleaning solution for carpet and bare floor application only. It does not heat solution sprayed through the accessory tools. 2. 3. The SmartTemp Ready Light indicates the heater is ON. It is found on the front of the handle where it is easy to see while you clean. Wait two minutes for the heater to warm up before beginning to clean. SmartTemp increases the water temperature up to 25° and will not allow it to exceed 180°. SmartTemp Ready Light SmartMixTM Provides custom control for each cleaning job. SmartMix Bottle 1. 2. 3. Lift the SmartMix Bottle up and out of the machine base. Turn the SmartMix Bottle over so that the Valve Cap is in an upward position. Unscrew the Valve Cap and fill the SmartMix Bottle to the mark with BISSELL Advanced Deep Cleaning Formula. Replace the Valve Cap, turning until snug. Valve Cap 6 ug310-5829_7920K_405.indd 6 5/5/06 11:25:17 AM SmartMix Continued 4. Replace SmartMix Bottle. Note: If SmartMix Bottle leaks, check for proper positioning of o-ring and straw. O-ring Position 5. Choose the SmartMix setting that fits the cleaning job. Water Rinse- use for gentle cleaning or for the final rinse after cleaning. Normal- automatically provides the best mix of water and concentrate for most cleaning jobs. High Traffic- automatically mixes the right amount of water and cleaning solution to dissolve tough grime and heavy soil. Note: Residual cleaning materials left in carpet from other products may cause excessive foaming when picked up. If foam is overflowing Tank, move SmartMix Dial to "Water Rinse" position until the condition stops. Note: Both the SmartMix Bottle and the clean water Tank must have liquid in them in order for the machine to spray. If one is empty, the machine will temporarily lose its prime and will not spray cleaning solution or water. Important: If you are using the WATER RINSE setting, fill the SmartMix Bottle with water also! H TR IG AFH N W OR FIC AT M ER AL R IN SE SmartMix Dial Tip: Deep cleaning stairs and high traffic areas on a regular basis can prolong carpet life. DirtLifter PowerBrush The powered brush roll at the Floor Nozzle is designed to enhance cleaning performance. The bristle pattern lifts out the deep down dirt while gently grooming carpet fibres. The floating suspension self-adjusts to all carpet heights. When the machine handle is in the fully upright position, Carpet SaverTM automatically raises the brush off the carpet and protects your carpet if you leave the Power Switch ON. TM WARNING: To reduce the risk of fire, use only BISSELL Advanced Deep Cleaning Formula for full size machines in your OxyPro. Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void the warranty. Chemical spot cleaners or solvent based soil removers should not be used. These products may react with the plastic materials used in your OxyPro, causing cracking or pitting. 7 ug310-5829_7920K_405.indd 7 5/5/06 11:25:18 AM Tank-in-Tank Our Tank-in-Tank system is designed with a Bladder inside for clean water. As you clean, the Bladder will empty. Dirty water collects in the tank outside the Bladder. Step on Handle Release to lay the machine handle down out of the way. 1 1. 2. 3. Lift the Tank-in-Tank handle. The handle locks the lid in place. Handle Release Carry it like a bucket to fill at the sink. Note: Both the SmartMix Bottle and the clean water Tank must have liquid in them in order for the machine to spray. If one is empty, the machine will temporarily lose its prime and will not spray cleaning solution or water. Set the Tank down and rotate the handle forward to unlatch the lid. Lift off and set the lid aside. Find the mouth of the Bladder and fill to the bottom of the neck with clean hand hot tap water. Do not boil or microwave water as it can destroy the Bladder. Note: Fill the Bladder with clean hand hot tap water only. Replace the Tank Lid matching the lid and tank edges. Handle must be in the forward position to re-install. Rotate the handle to the carrying position to re-latch the lid. Replace Tank in machine base, seating firmly in place. Lift and Carry 3 4. 5. 6. 7. 8. 9. 4 Rotate Handle to unlatch 5 Rotate handle back down to the latched position. Note: Both the SmartMix Bottle and the clean water Tank must have liquid in them in order for the machine to spray. If one is empty, the machine will temporarily lose its prime and will not spray cleaning solution or water. Important: If you are using the WATER RINSE setting, fill the SmartMix Bottle with water also! 9 Fill Bladder only with clean hand hot tap water When It's Time to Empty Tank-in-Tank Latched 1. 2. 8 Remove the Tank-in-Tank ­ follow steps 1 and 2 above. Carry the Tank-in-Tank, like a bucket, to the sink where you will dispose of the dirty water. ug310-5829_7920K_405.indd 8 5/5/06 11:25:19 AM When It's Time to Empty Tank-in-Tank Continued 3. 4. 5. Remove Tank Lid by rotating handle forward to unlatch lid and lifting lid off Ta ...