ATTACH SALES RECEIPT HERE High-Power FM/AM/Cassette Receiver with Detachable Face AutoradiolCassette AM/FM de Forte Puissance 2 Face Amovibie Receptor FM/AM/Reproductor de Cassette de Alta Potencia y con Cartitula Desmontable `,, Rtidio FMIAM/Toca-Fitas de Alta Potencia corn Face Removivel Bosch Corporation Sales GroupBlaupunkt Division 2800 South 25th Avenue Broadview, Illinois 60153 288E7650 Robert FCC WARNING The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limfts are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications, However, there is no guarantee that radio interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. OWNER'S RECORD The model and warranty numbers are located on the top of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you Call upon your Blaupunkt dealer regarding this product. Warranty Number purchase of this Blaupunkt FM/AM/Cassette Receiver. Its Optimum Reception Control (ORC IV) quartz FM and AM Tuner and high-quality, cassette tape player provide the ultimate in sound reproduction. l Audio Features: l General Features: . Cassette Features: l Tuner Features: - Detachable Faceplate for Securfty - Autoreverse Cassette Mechanism - 4 x 36 Watt Max. Integrated - ORC IV Tuner Amplifier - Switchable Clock/Function LCD Display - True Fast-Forward/Rewind - 12 FM/6 AM Presets - Volume/Balance/Fader Controls - Quick-Connect Wire Harness - Hard Pemtalloy Tape Head Travelstore FM/AM - Adjustable Turn-On Volume-Level - 176 x 50 x 153.5 mm (7 x 2 x 6 in.) - Automatic and Manual Tuning - Separate Bass and Treble Controls DIN Chassis Your unit's detachable front faceplate makes the unit useless to would-be thieves. - Snap-In DIN Sleeve 8 Mounting Hardware allOW the Unit t0 COOf off before operating your unit. . If no power connection is supplied to the unit, check the connections first, If everything is in order, check the fuse. l If no sound comes from the speakers of a two-speaker system, set the fader control to the center position. l You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty. . If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer. FEATURES Congratulations on your PRECAUTIONS . If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside the vehicle, DETACHABLE FACE Detaching & Attaching the Face: The face of this unit can be detached and taken with you to prevent It from betng stolen Detaching the Face: Before detaching the face, be sure to press the PWR Button first. Then press the REL (Release) Button and detach the face by gently pulling it off as Illustrated. Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it from the chassis. I Attaching the Face: Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at the front of the chassis. Gently push the left side of the face against the front of the chassis until it snaps into place. Note: Make sure that the face is inserted right side up. Do not press against the display window. Do not press hard against the face when attaching it to the chassis, it may be easily attached with gentle pressure. Do not expose the face to direct sunlight, heat sources such as hot air ducts or leave it in a humid place. Never leave it on the dash board of a vehicle parked in direct sunlight, where there may be a considerable rise in temperature inside the vehicle. Afflxlng Faceplate For Retail Display: The faceplate can be affixed to the units chassis, which is desirable for a retail display, for example. This should only be done in situations where the unit can be accessed from behind the mounting surface. Once the faceplate is affixed, the release keys cannot be used to remove the chassis. To affix faceplate, obtain the small bolt (M2.6 x 10) from hardware pack and drive it into the upper hole at the front of the left side of the chassis using a Phillips screwdriver. The bolt will self-thread the hole. (See above*) ELECTRICAL CONNECTIONS AND INSTALLATION @k?#&`>@! To avoid the aggravation of costly mistakes and serious damage that could make you feel this way. please carefully read all of the instructions before you begin. You'll be glad you did! GENERAL RECOMMENDATIONS If you're not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt installation technician. Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC). l Be sure to detach the faceplate before you start to connect or install the unit. l If you use the unit's connector with or without an adapter, make sure that function of the leads (wires) of the connector match the function of the leads in the mating connectors! - If your vehicle's radio wire harness is not compatible with this unit's harness connector, you can either a. buy an adapter harness at a car audio store -or- b. cut off the units connector and use a different type of connection. l We recommend making and testing all electrical connections before installing the unit. . Connect the leads (wires) according to instructions and diagram below unless the speaker's or amplifier's manual states that this is O.K. l l ELECTRICAL CONNECTION INSTRUCTfONS Disconnect the vehicle battery's negative terminal before making connections. : Before any other connections are made, you must first connect the antenna in order to avoid damage from mis,viring. 3 Connect speakers following the guidelines in the SPEAKER CONNECTION section below. 4. Connect the black (power ground) lead to a grounded metal part on the vehicle. We recommend grounding all audio system black ground leads (head unit, CD changer, etc.) to a common grounding point, preferably a non-painted surface under the instrument panel. Connect the yellow (constant power) input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box. Connect the red (turn-on power) input lead only after the other leads are connected. Be sure to connect the red lead to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the on position or accessory position. 7 Cover the ends of any unused leads with electrical tape. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the radio or vehicle, 6 Reconnect the vehicle's battery 9 Venfy that no fuses have blown 10 Plug the harness into the ""0 11 Attach the faceplate and test the "not Once the connections have been successfully made, you can begin to install the unit 5. 6. l SPEAKER CONNECTfONS You can connect a speaker (regular, co-axial or hi-axial speakers or component speaker system, all hereafter referred to simply as "speaker') to each of the units' four pairs of speaker leads. Connecting the Speaker Leads To prevent short circuits or serious damage to the unit and/or speakers: l Connect the speaker leads only as indicated in the wiring diagram. l Only use speakers that have impedance ratings of 4 ohms or higher and have power-handling capabilities greater than the head unit's stated power level. l The units internnl amplifier is designed to handle a 4-ohm load on each pair of speaker leads. l DON'T connect two speakers to a single pair of speaker leads ("in parallel") unless both speakers each have at least 6 ohms impedance. l DON'T connect the left and right speaker leads to each other or to the same speakers, l DON'T connect the front and rear speaker leads to each other or to the same speakers. l DON'T connect the negative speaker leads to each other. l DON'T connect the positive speaker leads to each other. l DON'T connect any active speakers (with built-in amplifiers) to the speaker leads. Adding CD Changer: You can easily play compact discs through this unit by adding the Blaupunkt CDC-RF6 6-Disc Compact Disc Changer. The space-saving CDC-RF6 easily plugs into the units antenna jack and comes complete with its own commander control. See your Blaupunkt dealer for details! INSTALLATION Recommendations * Carefully choose the mounting location so that the unit won't interfere with normal driving. * Avoid mounting locations where the unit would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would subject to dust, dirt or excessive vibration * The Illustration below shows a typuzal installation, however, you may need to adjust the s'tstaltatlon. depending on the unit. If you have questions or need additional installation hardware, consult your Blaupunkt dealer. l Make sure the uniiis firmly anchored (preferably at both front and back) Mounting The Unit in Most Dashboards and does not vibrate. 1 Install the Sleeve in the dashboard. 2 Select and bend the appropriate tabs to hold the sleeve firmly in place. 3 A. Attach the Mounting Strap to the underside of the dashboard, using screw. B. Attach the back of the unit to the mounting strap using the support stem bolt and hardware. Bend these tabs Mounting the Unit in a Japanese Car You may have difficulty mounting this unit in some Japanese cars. In this case, consult your Blaupunkt dealer. Removing the Unit Use the Release Keys as shown below. Keep them in a safe place in case You need them in the future. 1 f-gq @, 1 MAINTENANCE Fuse Replacement When replaclng the fuse. be sure to use one with the correct amperage, whtch will be slated on the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this unit. as this could cause malfunction and serious damage to the unit. SPECIFICATIONS Audio Power Specifications Power Output and Total Harmonic Distortion: 10 watts per channel minimum continuous average output into 4 ohms, 4 channels driven, from 30-15.000 Hz with no more than 1% total harmonic dIstortIon . Other Specifications Tuner FM Tuning Range: 87.5 - 107.9 mHz Audio 10.7 mHz IntermedIate Freouencv: Speaker Impedance: 4-8 ohms 18 dBf FM Mono Sensitiiity: ~' Maximum imp Power: 30 Watts x 4 (at 4 ohms) Selectivity: 75 dB at 400 kHz iowansx4 RMS Power: Signal-to-Noise Ratio: 85 dB (stereo), 70 dB (mono) Bass Control: +iO dB @ 100 Hz Harmonic distortion at 1 kHz: 0.7% (stereo), 0.5% (mono) *lOdB@ 10kHz Treble Control: Separation: 30 dB . . Cassette Frequency Response: 30-l 5,000 Hz f 3 dB Signal-to-Noise Ratio: 53 dB .bM. . Tape Wow and Flutter: 0.10% Tuning Range: 530 - 1,710 kHz Tape Frequency Response: 50-l 5,000 Hz * 3 dB Seek lo sensitivitv 55 dBpV General Seek sensitivity: ' 35 dBpV Dimensions (w/o proiectinq parts/controls): 178 x 50 x 153 mm 45" _kH, _ ._ Intermediate Frequency: 7 x 2 x 6 in. Signal-to-Noise Ratio: 45 dB Mass: Approx. 1.4 kg (3.0 lb.) Design and specifications subject lo change withouf notice. Power Requirement (neg. gmd.): 12 V DC car battery Operating Temperature: 15°F to 12O'F. -10°C to 50°C l Untt l Faceolate Supplied Accessories: r l Mounting Hardware * DIN Sleeve l Owner's Manual In English, French, Spanish and Portuguese INSTRUCTIONS - GENERAL OPERATION "Press" means momenlaly press of less than l/Z second Turning Unit On Vehicle lgnlbon must be on To turn unit on. press PWR Button. Turning Unit Off Press the PWR Button to turn the u",t off Volume Press + or-to quickly increase or decrease the volume to the desired level. The volume level is indicated in lhe Display Window. To make a fine adjustments to the volume level. press the other part of the button before the volume level disappears from the display. You can then gradually adjust the volume I" either direction, making precise adjustment easy. Adjustable Turn-O" Volume First adfust the volume to the (maxtmum) volume level dewed when the unit IS turned on Press and hold the PWR Button for more than two seconds The untt turns off and the turn-on volume level IS memowed When the unit 8s turned cm. the volume wll be at the mamonzed Iavel. avan II the unit was turned off while the volume was at a hlgher level However, II the volume IS turned off when the volume level IS lower than the stored TumOn volume level. the volume wit be at the lower level when the ...