High-Pow /CD Receiver with Detachable Face Autoradio Lecteur CD de Forte Puissance et a Face Arnovible Receptor F /AM/Reproductor de CD de Alta otencia y con Car&da Desmontable 288E7890 Robert Bosch Corporation Sales Group Blaupunkt Division 2800 South 25th Avenue, Broadview, Illinois 60153 FCC WARNING The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Pad 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions may cause harmful interference with radio communications. However, there is no guarantee that radio interference Will not Occur in particular installation. If this eouiomenidoes cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to contact the healer or an expenenced RadiofrV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. CAUTION l The use of optical instruments with this product will increase eye hazard. l Because the invisible laser beam in this compact disc player is harmful to the eyes. do not attempt to disassemble this cabinet. Refer servicing to qualified personnel only. SAFETY CERTfFlCATlON This Compact Disc Player is made and tested to meet exacting safety standards. It meets FCC requirements and complies with safety performance standards of the US Department of Health and Human Services. OWNER'S RECORD The model and warranty numbers are located on the top of the unit Record the serial number in the space provided below Refer to these numbers whenever you Call upon your Blaupunkt dealer regarding this product. Warranty Number FEATURES Congratulations on your purchase of the Blaupunkt CD Receiver. Its Optimum Reception Control (ORC Ill) quartz FM/AM tuner Anti-Vibration 8. Shock CD Mechanism provide the ultimate in sound reproduction. Its high-power amplifier and Z-channel RCA preamp output provide tremendous system configuration flexibility. l Audio Features: . General Features: l Tuner Features: l CD Features - Detachable Faceplate for Security - ORC III Tuner - Track Scan - Track Up/Down - 35 Watts (Peak) x 4 Channel Integrated Amplifier - Switchable Clock/Function LCD Display - 12 FM/6 AM Station Presets, - Pause/Play - Cue/Review - Ignition-Off Clock Recall Including Travelstore for all Presets - Track Mix - Track Repeat - P-Channel RCA Preamp Output: - Dual-Level Fader Green Illumination - RPD 435 - Automatic and Manual Tuning - Track Number Indication - Volume/Balance/Fader Controls - Amber Illumination - RPD 435X - Station Scan 8 Preset Scan - Elapsed Track Time Indication - Adjustable Turn-On Volume-Level - Detachable Wire Harness - RPD 435X US/Euro Tuning - DISC IN Indicator 176x50x155.5mm (7x2x6inJDIN - 1 Bitf6 Times Oversampling Digital Filter - Loudness Control - Chassis Your unit's detachable front faceplate - Silicone-Oil Dampened Anti-Vibration - Separate Bass and Treble Controls - Snap-In DIN Sleeve & Mounting Hardware makes the unit useless to would-be and Shock CD Mechanism thieves. PRECAUTIONS l The use of optical instruments with this product will increase eye hazard. . Because the laser beam in this compact disc player is harmful to the eyes, do not attempt to disassemble this cabinet. Refer servicing to qualified peffionnel Only. . If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside the vehicle, allow the Unit to Cool Off before Operating yOUr Unit. l If no power connection is supplied to the unit, check the connecticns first. If everything is in order, check the fuse. l If no sound comes from the speakers of a two-speaker system, set the fader control to the center position. . You are cautioned that any changes or modifications not expressly approved in this manual could void your Warranty. . If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer. DETACHABLE FACE Detaching & Attaching the Face: The face of this untt can be detached and taken with you to prevent it from being stolen. Detaching the Face: Press the REL (Release) Button and detach the face by gently pulling it off as illustrated. (See Fig.1 below.) Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it from the chassis. Attaching the Face: Apply the right hand side of the face to the chassis by sliding it into the right side of the chassis. Gently push the left side of the face against the front Of the chassis Until it Snaps into INSTALLATION Recommendations Carefully choose the mounting location so that the unit won't interfere with normal driving. Avoid mounting locations where the unit would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would subject to dust, dirt or excessive vibration. l The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the unit. If you have questions or need additional installation hardware, consult your Blaupunkt dealer. l Make sure the unit is firmly anchored (preferably at both front and back) and does not vibrate. Mounting Hardware Mounting The Untt In Most Dashboards 1 Install the Sleeve (1) in the dashboard. 2 Select and bend the appropriate tabs to hold the sleeve ftnnly in place. 3 A. Attach the Mounting Strap (2) to the underside of the dashboard, using screw. B. Attach the back of the unit to the mounting strap using the support stem bolt and hardware. l l Dash Mounting the Unft In a Jspaneae Car You may have difficulty mounting this unit in some Japanese cars. In this case, consult your Blaupunkt dealer. Removing the Untt Use the Release Keys as shown below. Keep them In a safe place In case you need them In the future. Fuss Replacement When replacing the fuse, be sure to use one with the correct amperage, which will be stated on the fuse. Never use a fuse that has a stated amperage exceeding the one supplied for this unit, as this could cause malfunction and serious damage to the unit, Bend these tabs SPECIFICATIONS Audio Power Stmclflcatlona Power Output and Total Harmonic Distortton: 13.5 watts per channel minimum continuous average output Into 4 ohms, 4 channels driven. fmm 30-15,COO Hz with no more than 1% total harmonic distortion. Dther %eclflcatlona Tuner \ FM Tuning Rage 675-1079MHz 67 5 106 0 MM IRW 435X onlvl I. Intermediate Frequency: 10.7MHz FM Mono Sensitivity: 6 dBf Seek Sensitivity 22 dBf Selectivity: 60 dB at 400 kHz Signal-to-Noise Ratio: 70 dB (stereo). 75 dB (mono) Harmonic Distortion at 1 kHz: 07;B(sterec). 0.5% (mono) Separation: Frequency Response: 30-15,ooO Hz * 0.75 dB Design and specifications subject to change without notice. AM 530-1.7lOkHz 531 - 1.502 kHz (RPD 435X only) Seek Sens!tiv!ty 31 dBpV lnlermedrate Frequency 450 kHz SIgnal-to-Norse Ratlo 50 dB Audio Speaker Impedance MaxImum Amp Power RMS Power Bass Control Treble Control Loudness Preamp Outputs Preamp Output Voltage 4.6ohms 4 x 35 Watts (at 4 ohms) 4 x 17 5 Watts (at 4 ohms) +lOdBOlOOHz tl0 dB @ 10 ktiz tlOdB01100Hz &+7dB@0kHz 2.CH RCA 1.5 volts maximum 8 100% Modulation with < 1% Total Harmonic Distortion Tunmg Range (:D :innal-h-No& R&o: Player *`";l;;; Range: & Frequency Response: Harmonic Distortion: General Drmensions (w/o projecting parts/controls): 176x50x155.5mm 7 x 2 x 6 in. Mass: Approx. 1.4 kg (3.0 lb.) Power Requirement (neg. gmd.): 12 V DC car battery Operating Temperature: 15°F to 120°F. -10°C to 50°C Supplied Accessories: 9 Unit . Faceplate l DIN Sleeve l Mounting Hardware l Owner's Manual in English, French, Spanish and Portuguese 63 dB 90dB 5-20,COO Hz f 3 d6 I 620,000 Hz f 1 dB .Ol% Note: Make sure that the face is inserted right side up. Do not press against the display window. Do not press hard against the face when attaching it to the chassis, it may be easily attached with gentle pressure Do not expose the face to direct sunlight, heat sources such as hot air ducts or leave it in a humid place. Never leave it on the dash board of a vehicle parked in direct sunlight, where there may be a considerable rise in temperature inside the vehicle. Afffxing Faceplate For Retail Display: The faceplate can be affixed to the unit's chassis, which is desirable for a retail display, for example. This should only be done in situations whom the unit can be accessed from behind the mounting surface. Once the faceplate is affixed, the mlease keys cannot ba used to remove the chassis. To afffx the faceplate, obtain the small bolt (M2.6~10) from hardware pack and drive it into the upper hole at the left of the chassis using a Phillips screwdriver. The bolt will self-thread the hole. (See' rn Fig.2.) ELECTRICAL CONNECTIONS AND INSTALLATION @/~?#&*~@I To avoid the aggravation of costly mrstakes and serious damage that could make you feel this way, please carefully read all of the instructions before you begin Carefully follow all instructions. You'll be glad you did! GENERAL RECOMMENDATTONS l If you're not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt installation technician. l Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC). l Be sure to detach the faceplate before you start to connect or mstall the unit. l We recommend making and testing all electrical connecttons before installing the unit. Connact the leads (wires) according to instructions and diagram below. ELECTRICAL CONNECTtON INSTRUCTIONS 1. &connact the vehicle battery's negative terminal before making connections. 2. Connect the speakers and/or external amplifiers (if you have any) following the guidelines in the SPEAKER CONNECTION section below. 3. Connect the blue (trigger output) lead to the amplifier's trigger input terminal and/or antenna motor trigger input terminal (if you have either or both of these Items). The combined total amperage required for triggering the antenna motor and/or amplifier must not exceed 100 mA. DO NOT connect the blue lead to the antenna's and/or amplifier's power supply input. 4. Connect the black (power ground) lead to a grounded metal part on the vehicle. We recommend grounding all audio system black ground leads (head unit, external amplifier, etc.) to a common grounding point, preferably a non-painted surface under the instrument panel. Connect the yellow (constant power) input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box. :: Connect the red (turn-on power) input lead only afler the other leads are connected. Be sure to connect the red lead to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the on position or accessory position. 7 Cover the ends of any unused leads with electrical tape. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage lo the radio Or vehicle. 8 Reconnect the vehicle's battery. 9 connect me antenna plug. 10 Verify that no fuses have blown. 11 Plug the harness into Ihe unit. 12 Attach the faceplate and lest the unit. Once the connectrons have been successfully made, you can begln to mount the unit SPEAKER CONNECTtONS The unrt's Dual-Level Fader allows you to lade between the front and the rear channels using either the from and/or rear speaker leads and/or the rear preamp outputs, providing you tremendous flexibrlity in configuring your speaker arrangement l You can connect a speaker (regular, co-axral or td-axral speakers or component speaker system, all hereafter referred to simply as `speaker") to each of the units' four pairs of speaker leads. l You can connect the 2 RCA preamp outputs to mbltiple external amplifiers and power multiple speakers or speaker systems through the amplifiers. (Blaupunkt ampkfters and speakers available separately. Call l-800-950-2528 for product brochure and/or dealer referral.) l You can use a combination of these two methods. Connecting the Speaker Leads To prevent short circuits or sertous damage to the unit and/or speakers: l Connect the speaker leads only as indicated in the wiring diagram. l Only use speakers that have impedance ratings of 4 ohms or hrgher and have power-handling capabilities greater than the head unit's stated power level. l The unit's internal amplifier is designed to handle a 4-ohm load on each pair of speaker leads. l DON'T connect two speakers to a single pair of speaker leads ("in parallel") unless both speakers each have at least 8 ohms impedance l DON'T connect the left and right speaker leads to each other or to the same speakers. ...