User manual BLAUPUNKT TRAVELPILOT DX-R70

TravelPilot Navigation Radio/CD TravelPilot DX-R70 Operating instructions http://www.blaupunkt.com INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 2 Device overview 1 2 3 4 5 6 7 8 9 17 16 15 14 13 12 11 10 1 2 3 4 button ­ opens the control panel. Button to switch the unit on/off and operate the mute volume function. Volume control. Macro button ­ programmable function button. For further information, read the section entitled "Programming the macro button" in the "Setup" chapter. Dot matrix display. If pressed briefly during navigation: the active destination is displayed and the last voice output is repeated. Entries that are marked with "..." in a list will be displayed in their entirety. Rocker switch. The way the rocker switch functions depends on the individual menus or operating modes. OK button, enter key. 9 : ; < = > ? @ A MENU button ­ to activate the setup menu. AUD button ­ opens the audio menu. ESC button ­ closes menus and deletes characters in speller menus. Softkeys 4 to 6. The way the softkeys function depends on the menu contents. Softkeys 1 to 3. The way the softkeys function depends on the menu contents. NAV button­ activates navigation. 5 6 7 8 TUNE button ­ switches to radio mode. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 3 DEUTSCH DEUTSCH CD.C button ­ activates CD or CD-changer mode. DEUTSCH ENGLISH T button ­ opens the TRAFFIC menu: TIM function (Traffic Information Memory) and TMC traffic information messages. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 4 Dear Customer, Congratulations on buying the TravelPilot DX-R 70. You can rest assured that you have made the right choice by buying the TravelPilot DX-R 70. The TravelPilot DX-R 70 is a radio navigation system the size of a standard car radio. However, it offers a whole lot more! The TravelPilot is a reliable and easy to use navigation system that will lead you exactly to your destination. These operating instructions will take you through the functions of the TravelPilot DX-R 70 step by step and will answer the most frequently asked questions. You will find further information on using these operating instructions in the section entitled "About these instructions". If you have any further questions or comments regarding the TravelPilot DX-R 70, please do not hesitate to call our telephone hotline or contact your Blaupunkt dealer. The international telephone hotline numbers are printed on the last page of these instructions. Guarantee The scope of the guarantee depends on the regulations in force within the country in which the unit was purchased. If your unit develops a fault, please contact your dealer and present the purchase receipt. If the statutory guarantee period in your country is less than 12 months, Blaupunkt will grant a 12-month manufacturer's guarantee. This guarantee does not cover damage due to wear, incorrect usage or commercial use. If you wish to enforce a claim under the manufacturer's guarantee that is provided by Blaupunkt, please send the faulty unit together with the purchase receipt to the Blaupunkt customer service centre in your country. You can find out which address is closest to you by contacting the telephone hotline listed on the back page of this booklet. Blaupunkt retains the right to rectify defects or supply a replacement. Notice regarding liability Despite constant technical developments, the navigation system may in certain cases provide incorrect or unoptimised navigation due to improper operation, changes to the traffic flow regulation, construction sites, traffic load, errors or missing information on the navigation data media or general computer and positioning errors. Blaupunkt does not accept liability and does not provide compensation for any damages or other drawbacks arising from this. Overview of navigation functions NAVIGATION ROUTE GUIDANCE DEST. ENTRY DEST. MEMORY TOURLIST MERIANscout Press the NAV key once in order to switch from the radio or CD-changer (optional) audio sources to the navigation system's main menu or back to navigation (if a navigation session is already active). Use the keys on the rocker switch to select the DEST. ENTRY menu item and press the OK button. CITY/PLACE H_ HANNOVER A E _I L U Y H O the OK button pressed for longer than two seconds. You can also switch to the list if the name of a town that comes alphabetically before the town you require appears in the list. Use the keys on the rocker switch to select the CITY menu item and press the OK button. If the name of the town you are looking for appears in the name match line, keep 5 INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX DEUTSCH DEST. ENTRY CITY STREET CENTRE P.O.I. If you have already used the navigation system and the first letters of the new destination town are identical to that of a previous destination town (in this case HANNOVER), the town will be displayed in the match line (Last City History Function). This feature helps speed up entering destinations that you have visited before. If a DX navigation CD is inserted, letters that cannot logically follow a letter you have just entered will be hidden from view (the speller thins out). DEUTSCH Use the keys on the rocker switch to select the letters of the town you require. An appropriate entry will be displayed in the match line as you enter more and more letters. In the majority of cases, only a few letters will be required in order to enter the town that you are looking for. DEUTSCH ENGLISH INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 6 CITY/PLACE BERLIN BERLIN, NEUENH... BERLIN, RÜDERS... BERLIN, SCHÖNE... BERLIN, SCHÖNE... If you press the OK button for longer than two seconds after entering the destination, the list of destination towns appears. Use the keys on the rocker switch to move the selection marker to the name of the town you require. Once the selection marker is positioned over the name of the town you require, press the OK button. DEST. ENTRY STREET CENTRE DEST. SURROUND SCHLOSSWEND... 03h58 461 mi Europe 1 In the following selection, choose between STREET, CENTRE or destinations in the DEST. SURROUND area. Streets can only be selected if the data are available on the navigation CD that is being used. Menu items that cannot be selected are marked with a lock. If you selected STREET, you can subsequently also enter junctions or house numbers. Enter the name in the same way as you did for CITY. Select CENTRE if you want to be guided directly to the centre of a town district. Once you have finished entering your destination, navigation begins automatically. Navigation begins. The visual driving recommendations appear in the left of the display. In the centre you will see a display that provides a symbolic representation of the distance to the next decision point (e.g. a crossing). On the right you will see information on the current time, arrival time or remaining journey time as well as details on the set audio source, i.e. radio, CD changer (optional) or internal CD drive (only available with NO-MAP navigation). During active navigation you can control the audio functions as usual using the rocker switch. You can switch to audio mode at any time using the TUNE and CD·C source buttons. Navigation will then be continued with voice output only. To display navigation mode again, press the NAV button. Safety information The TravelPilot has been designed for use in passenger cars. Special information such as height restrictions or maximum permitted road load, which is required for navigating trucks and buses, is not included on the navigation CDs. Inserting / removing a CD or the KeyCard · · · For safety reasons, you should only insert or remove a CD / KeyCard when the vehicle is stationary. Only open the control panel to insert / remove a CD or KeyCard. Operating whilst driving If you do not pay attention to the road and traffic situation, you could cause serious accidents. · · · · Familiarise yourself with the TravelPilot and its controls before setting off on your journey. Stop your vehicle at a suitable location if you wish to re-programme the TravelPilot. Operate the TravelPilot whilst driving only if the road and traffic situation allow you to do so. Only enter a destination whilst the vehicle is stationary. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 7 DEUTSCH In order to avoid being distracted by the TravelPilot, please observe the following: DEUTSCH After inserting / removing a CD or KeyCard, close the control panel immediately to ensure that the unit is ready for operation before setting off on your journey. DEUTSCH ENGLISH INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 8 Device overview ....................... 2 Overview of navigation functions ................................... 5 Safety information .................... 7 About these instructions ......... 9 Theft protection KeyCard ...... 10 Switching the unit on/off ....... 12 Selecting the operating mode ................... Adjusting the volume ................................. Display ........................................................ Adjusting audio settings and sound distribution settings ................................... Starting navigation .................................... Navigation ................................................... Dynamic navigation ................................... Tour list ....................................................... Travel guide ................................................ Destination memory .................................. Bypassing a traffic jam during navigation ................................................... Defining route options ............................... Setting a position marker .......................... Activating / deactivating voice output ...... Manually setting your position ................. Simulating navigation ................................ 13 14 15 16 18 33 36 37 41 43 47 50 51 53 55 56 Radio mode ............................. 57 Switching to radio mode ........................... Selecting the frequency range or memory ....................................................... Switching RDS (Radio Data System) on / off ......................................................... Activating / deactivating RDS-REG .......... Switching PTY on/off ................................. TA (Traffic Announcement) ....................... TMC (Traffic Message Channel) ................ Tuning into FM stations ............................. Tuning into MW stations ............................ Scan seek tuning ....................................... TMC Scan .................................................... Storing stations .......................................... Reducing reception interference in FM mode ..................................................... Displaying radiotext ................................... TIM - Traffic Information Memory .............. Viewing TMC messages ............................. 57 57 57 58 59 60 61 62 63 63 64 65 67 68 69 72 CD changer mode .................. 82 Selecting a CD ............................................ Selecting tracks .......................................... Fast searching ............................................ Random play (MIX) ..................................... Scanning tracks (SCAN) ............................ Repeating tracks or CDs (REPEAT) .......... Programming playlists .............................. Naming CDs ................................................ 84 84 84 85 85 86 87 89 Steering wheel remote control ..................................... 93 Setup ­ basic settings ........... 95 Setting the day / night changeover, viewing angle and display brightness ..... 96 Configuring power-on / telephone / navigation / traffic information announcement volume and GALA settings .............. 97 Programming the macro button ............... 98 Setting the clock ...................................... 100 Selecting the language ............................ 102 Calibrating the device .............................. 103 Activating / deactivating the code LED .. 105 Resetting to the factory defaults ............ 106 Setting seek tuning sensitivity ............... 107 Preparing a second KeyCard ("Learning") .............................................. 108 Factory default settings .......................... 109 Navigation ............................... 17 CD mode ................................. 73 Playing a CD .............................................. 73 Selecting tracks ........................................ 75 Fast searching ........................................... 76 Random play (MIX) .................................... 76 Scanning all tracks on a CD (SCAN) ....... 76 TRepeating tracks (REPEAT) ................... 77 Naming CDs ............................................... 77 Programming playlists ............................. 79 Index ...................................... 112 Installation instructions ....... 338 About these instructions The aim of these instructions is to familiarize you with the functions of the TravelPilot DX-R 70 and ensure that you can safely and successfully operate the unit. Before starting to use your TravelPilot DX-R 70, please read these instructions carefully and keep them in a safe place in your vehicle. Note: Please make sure that you do not keep the equipment pass, which is enclosed in these instructions, in your vehicle. To help you find the information you need as quickly as possible, these instructions use the following symbols to denote individual steps: 1... Indicates the steps informing you how to carry out a particular action in order to achieve the intended system response to that action. Indicates the reaction of the unit towards the user's actions. TIP: Provides information and tips on operating the TravelPilot DX-R 70. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 9 DEUTSCH DEUTSCH DEUTSCH ENGLISH INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 10 Theft protection KeyCard The unit is supplied with a KeyCard. The TravelPilot can also be operated using a second KeyCard. Furthermore, the values that were set last for the frequency range, station tuner, traffic information announcement, RDS, REG, seek tuning sensitivity, power-on volume and SHARX are all stored. For information on how to prepare a second KeyCard for use with the TravelPilot, please refer to the section entitled "Preparing a second KeyCard" in the "Setup / basic settings" chapter. Note: If you no longer have a KeyCard for the TravelPilot, you can prepare a new KeyCard yourself. For further information, read "Preparing a new KeyCard ("Learning") / Entering the master code" in the "Setup / basic settings" chapter. Inserting a KeyCard To unlock the control panel, 1 2 3 4 Press the button 1. The control panel opens. Insert the KeyCard as shown in the picture (arrow 1) with the contact surfaces facing downwards. Carefully push the KeyCard and the KeyCard slide in the direction of the arrow (2) until they go no further. Close the control panel (arrow 3). 1 3 2 Removing the KeyCard To unlock the control panel, 1 2 3 4 Press the button 1. The control panel opens. Push the KeyCard and the KeyCard slide towards the right until they go no further. Remove the KeyCard from the control panel. Close the control panel. Note: As a precautionary measure against theft, remove the KeyCard when leaving the vehicle and leave the control panel open. Looking after the KeyCard DEUTSCH CD CHANGER SETUP INDEX 11 Keeping the contacts free from dirt and other particles will ensure that the KeyCard functions properly. Avoid touching the contacts directly. If necessary, clean the KeyCard contacts with a lint-free cloth soaked in alcohol. INTRODUCTION NAVIGATION RADIO MODE CD MODE DEUTSCH DEUTSCH ENGLISH INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 12 Switching the unit on/off 1 To switch on the TravelPilot when the KeyCard is inserted, press the blue button 2 in the centre of the volume control 3. The unit plays the audio source that was active last at the preset volume level. You can find out how to set the power-on volume in the section entitled "Configuring power-on / telephone / navigation / traffic information announcement volume and GALA settings" in the "Setup" chapter. Switching on/off using the KeyCard You can also switch the TravelPilot on/off by inserting and removing the KeyCard. Switching on when the vehicle ignition is off You can also operate the TravelPilot when the ignition is off and the KeyCard is inserted. 1 To do so, press the ON button 2. The unit switches on. After an hour has elapsed, the unit switches off automatically in order to protect the vehicle battery. You can repeat this procedure as often as you like. The imposed time limit is cancelled as soon as the ignition is turned on. Note: To ensure that the TravelPilot functions properly and that increased power consumption is avoided, the unit must be connected to the continuous power source and the power source via the ignition as described in the installation instructions. Selecting the operating mode To select the operating mode, press: 1 1 1 the TUNE button A for radio mode or the CD.C button @ for CD or CD-changer (optional) mode or the NAV button ? to activate navigation. If you change the source using one of these buttons, the main menu of the corresponding source will be opened. If navigation is active, you can switch from the main navigation menu to the active navigation session by pressing the NAV button ?. JUMP BBC JAM FM Main menu RADIO 1 EUROPE EINSLIVE Each audio source (tuner, CD and CD changer) provides three menus for configuring all the available settings. Main menu: This is where the most frequently used settings are configured, e.g. station or track selection. Functions menu: To configure functions such as traffic information standby and special functions like Travelstore. Setup menu: To adjust the options of the particular audio source to your personal requirements. Main menu for accessing the main navigation functions, Navigation menu with the visual driving recommendations, and Navi menu to adjust the navigation options to your personal requirements. JUMP FM1 FM2 MW Functions menu The following menus are available in navigation mode: - Switching between the main menu and functions menu To switching between the main menu and functions menu of an audio source, 1 press the corresponding TUNE A or CD.C @ source button again. REG PTY RDS Setup menu OFF ON TA ON OFF SHARX VAR OFF R-TXT INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 13 DEUTSCH JUMP DEUTSCH FMT FMC PAGE 2 DEUTSCH ENGLISH JUMP INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 14 Switching between the navigation system's main menu and navigation menu If you want to switch between the main menu and the navigation menu during an active navigation, 1 press the NAV button ?. If navigation is not active, position-tracking mode will be displayed. Opening the setup menu You can open the setup menu for a particular operating mode by briefly pressing the MENU button : once. Adjusting the volume To increase the system volume, 1 1 turn the volume control 3 in a clockwise direction. turn the volume control 3 in an anticlockwise direction. Whilst you are making your adjustments, the currently set value is displayed symbolically in the display foreground. TIP: During a spoken driving recommendation by the navigation system, you can adjust the volume of the driving recommendation independently of the basic volume level of the audio source. The difference in volume levels is stored automatically. Automatic volume mute during telephone calls If the unit is connected to a car telephone, the telephone call will be output over the TravelPilot's loudspeakers. The telephone symbol will appear in the display foreground of the audio source. If you are making a telephone call during an active navigation session, the visual driving recommendations remain visible and the audio driving recommendations are not silenced. To decrease the system volume, JUMP JUMP BBC JAM FM RADIO 1 EUROPE EINSLIVE Main tuner menu with volume indicator Display The TravelPilot's display contains all the navigation information (e.g. visual driving recommendations), menus and lists, as well as the menus relating to the radio, CD and CD changer (optional) audio sources. If the unit is connected as described in the installation instructions, the display switches to night-time mode when the vehicle lights are turned on. This causes all the light pixels to be displayed dark and all the dark pixels to appear light. If you also drive during the daytime with the lights turned on, e.g. in Scandinavian countries, you can deactivate this feature. For further information, read the section entitled "Setting the day / night changeover, viewing angle and display brightness" in the "Setup" chapter. The display's readability can be optimised to suit the viewing angle in your vehicle. For further information, read the section entitled "Setting the day / night changeover, viewing angle and display brightness" in the "Setup" chapter. Note: Please treat the display covering pane with care. Contact with sharp objects causes scratches and damages the covering pane. Only clean the covering pane with a lint-free cloth and, if necessary, with cleaning spirits. Do not use any solvents such as turpentine or petrol when cleaning, since these will affect and damage the covering pane. JUMP BBC JAM FM RADIO 1 EUROPE EINSLIVE Main tuner menu, daytime display JUMP JUMP BBC JAM FM RADIO 1 EUROPE EINSLIVE Main tuner menu, night-time display INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 15 DEUTSCH DEUTSCH DEUTSCH ENGLISH JUMP INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 16 Adjusting audio settings and sound distribution settings The TravelPilot allows you to adjust the bass and treble for each audio source. Changes to the balance and fader sound distribution settings and loudness settings (aurally compensated volume) affect all the audio sources. To adjust the audio settings, 1 press the TUNE button A or CD.C button @ to switch to the audio source (radio, CD or CD changer) for which you would like to adjust the settings. Press the AUD button ;. The audio settings menu opens. Use the / buttons on the rocker switch 7 to move the selection marker to the menu item whose settings you want to change. Use the / buttons on the rocker switch 7 to make the adjustments. The slide control is highlighted. press the OK button 8. The border around the slide control disappears and the values are saved. Note: If you do not press a button within 30 seconds, the display will switch back automatically to the initial menu (timeout). FM TONE BASS TREBLE BALANCE FADER LOUDNESS + + + 2 3 4 5 If you wish to apply your adjusted values, FM TONE BASS TREBLE BALANCE FADER LOUDNESS Audio menu for the FM radio audio source + + + Navigation The navigation system in the TravelPilot DX-R 70 helps you find your way to destinations quickly and safely without first having to spend time studying a roadmap. When navigation is active, you will be guided by the DX-R 70's voice output. The system will warn you in good time about approaching turning-off points. In addition, the display contains visual driving recommendations, the distance to the destination, the estimated remaining driving time / arrival time or the current clock time. Road safety has absolute priority. Please be aware that the current way in which traffic is being directed always has priority over the driving recommendations made by the navigation system. How navigation works The current vehicle position is determined with the aid of the electronic odometer, the gyro and a signal transmitted by GPS (Global Positioning System) satellites. The navigation system compares the data with the map stored on the navigation CD and uses this information to calculate your position and the routes used for navigation. Inserting the navigation CD 1 2 3 Press the button 1 to open the control panel. Press the eject button B to remove a CD that may already be in the unit. Carefully insert the CD with the printed side uppermost into the unit's CD compartment. Push the CD until you feel some resistance. From this point onwards, the CD will be drawn in automatically. 18 INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 17 DEUTSCH DEUTSCH DEUTSCH ENGLISH INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 18 The software is loaded from the CD. The progress is indicated in the display. Note: The process of loading the software from the navigation CD must not be interrupted. Starting navigation 1 Press the NAV button ? whilst the unit is switched on. The main navigation menu opens. If a navigation session is already active, the navigation display will appear. NAVIGATION ROUTE GUIDANCE DEST. ENTRY DEST. MEMORY TOURLIST MERIANscout Main navigation menu Before navigation can begin, a DX navigation CD must first be inserted in the unit and a destination selected. Entering a destination The destination can be entered from the destination memory or by entering a town, a town centre, a road, a junction or house number, or by selecting a special destination (e.g. motorway junction, train station, etc.). 1 2 Use the / buttons on the rocker switch 7 to select the DEST. ENTRY menu item. Confirm your selection by pressing the OK button 8. Destinations The following destinations are allowed: · · · · the town centre or centre of a district in cities, a road, a junction where two or more roads intersect, a house or housing block. · · Position markers that you have set and which have been stored in the destination memory. This is useful if you notice an interesting location during your journey, like a shop or restaurant, and want to be guided back to that point at some other time. Destinations from the destination memory. Destinations from the tour list. · Entering destinations using the speller The speller is used to enter items such as town and road names in the navigation system. The speller consists of five areas: 1 2 3 4 5 the list of characters including all letters, the space character, special characters and numbers, the control symbols, the input line, the match line, and the magnifier within which the currently highlighted characters are displayed in an enlarged fashion. CITY/PLACE _ 3 4 N 5 2 DEUTSCH 19 ABCDEFGHIJKLMNO 1 PQRSTUVWXYZ ÄÖÜ Speller Selecting letters If you want to enter a name using the speller, proceed as follows: 1 Use the / and / buttons on the rocker switch 7 to move the selection marker to the required character. When you move the selection marker, the currently highlighted character is displayed in an enlarged fashion within the magnifier. NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX INTRODUCTION DEUTSCH DEUTSCH · ENGLISH Previously saved special destinations such as train stations, airports, petrol stations and other public facilities. You can view a sorted list of special destinations for the destination town, the area around a destination, on a national level or in the vicinity of the vehicle position. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 20 2 When the required character is highlighted, press the OK button 8. The character will be entered into the input line. An appropriate entry from the list will be displayed in the match line as you enter more and more characters. TIP: If you have already used the navigation system before for navigation and the first letters of the new destination town are identical to those of a previous destination town (in this case Hanover), the town will be displayed in the match line. This feature helps you quickly enter destinations in towns that you have visited already. CITY/PLACE H_ HANNOVER A E _I L U Y H O If you want to accept the town name, press the OK button 8 for longer than two seconds. If, however, you want to enter another town name, simply continue entering characters. TIP: The "thinning out" speller feature is available for navigation CDs that are labelled with a "DX". The thinning out speller feature ensures that letters, which cannot logically follow a letter that you have just entered, will be hidden from view. Switching to special character sets If, when enter a town name, you need to use other special characters that are not shown in the display (e.g. Ä, Ö, Ü), 1 2 use the buttons on the rocker switch 7 to move the selection marker to the control symbol. Press the OK button 8. Every time you press the OK button 8, other special characters will be displayed in the speller. TIP: When using navigation CDs labelled with a "DX", special characters are switched on automatically. CITY/PLACE _ N ABCDEFGHIJKLMNO PQRSTUVWXYZ ÄÖÜ Deleting letters 1 1 press the ESC button < or highlight the symbol and press the OK button 8. The input cursor will move to the left in the input line. If the required name appears in the match list whilst you are entering the name in navigation mode, 1 2 highlight the symbol and press the OK button 8. The list display (e.g. list of destination towns) opens. The entry is highlighted. Browsing through lists In lists with fewer than ten entries, 1 2 use the button on the rocker switch 7 to move the selection bar to the last list entry. Pressing the button again 7 causes the next list page to be displayed. Paging through lists To find the entry you are looking for quickly in large lists, you can also browse the list page by page. 1 Use the symbol. / buttons 7 to move the selection bar to the or arrow ROUTE LIST O.1mi ASTERNST... 0.4mi ENGELBOS... 0.1mi AN DER C... 0.4mi SCHLOSSW... 1.8mi BREMER D... List (here the route list) CD CHANGER SETUP INDEX INTRODUCTION NAVIGATION RADIO MODE CD MODE 21 DEUTSCH DEUTSCH Since the number of lines in the display is limited to five, some lists containing more than five entries are divided into several "pages". Lists containing more than five items are marked with arrows on the right-hand side. There are two ways of opening the next page in a list: DEUTSCH 1 keep the OK button 8 pressed for longer than two seconds or ENGLISH To delete a letter that you entered accidentally, INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 22 2 3 1 Press the OK button 8. The previous or next list page is displayed. The selection bar remains on the arrow button. Keep pressing the OK button 8 until you reach the required page. Press the OK button 8 to accept the entry. Selecting list entries Entering a destination ­ town If you want to drive to a destination in a town, you first have to specify one. 1 2 3 4 Select the DEST. ENTRY item in the main navigation menu. The destination input menu opens. Select CITY. The speller for entering the town name opens (for further information read the section entitled "Entering destinations using the speller"). Use the / and / buttons on the rocker switch 7 to move the selection marker to the required character. When the required character is highlighted, press the OK button 8. The character will be entered into the input line. The first town in the list of destination towns whose name begins with the selected letter will appear in the match line. TIP: If you have already used the navigation system and the first letters of the new destination town are identical to those of a previous destination town, the town will be displayed in the match line. This feature helps you quickly enter destinations in towns that you have visited already. TIP: The "thinning out" speller feature is available for navigation CDs that are labelled with a "DX". The thinning out speller feature ensures that letters, which cannot logically follow a letter that you have just entered, will be hidden from view. If the name of the destination town you require appears in the match line, 5 keep the OK button 8 pressed for longer than two seconds. The list of destination towns opens. The name is highlighted. DEST. ENTRY CITY STREET CENTRE P.O.I. Destination input menu INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 23 DEUTSCH DEUTSCH DEUTSCH ENGLISH INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 24 6 Press the OK button 8 to accept the town as your destination. If there are multiple instances of the town's name, a submenu will open. You can then select the required town from it. If you do not want to accept the town as your destination, 1 press the ESC button <. You will return to the speller. Once you have entered the town, you will continue with DEST. ENTRY. Now choose between: STREET: to enter the destination street. Whether a street can be entered as a destination depends on the data stored on your navigation CD. CENTRE: to select a town centre or centre of a town district as your destination. DEST. SURROUND: you can directly select special destinations from a list classified in categories (e.g. motorway junction, train station, shopping centre, etc.) within the vicinity of the destination. To do so, read the section entitled "Special destinations, destination surrounding area". DEST. ENTRY STREET CENTRE DEST. SURROUND Subsequent destination input menu, "city" has been entered A requirement is that the appropriate data are available on the navigation CD. If there are no data available for individual items, they will be marked with a lock symbol and cannot be selected. Entering a destination ­ street, junction and house number If you want to drive to a street in a town that you have already entered, you can also select STREET from the destination input menu in navigation mode. TIP: To make your search easier, long street names can also be stored in different ways, e.g. RAABE-WEG, WILHELM- and WILHELM-RAABEWEG. DEST. ENTRY CITY STREET CENTRE P.O.I. Destination input menu 1 2 - Enter the street name using the speller. Select the required street name from the list. If the street name occurs several times in the destination town, a submenu will open in which you can specify the street precisely. After the street has been selected, the destination input menu opens. Choose between the options: CONTINUE: Destination input is complete and navigation will be started. For further information, read the section entitled "Navigation". INTERSECTION: You can also select a junction on the selected street in order to define your destination more precisely. HOUSE NUMBER: In large towns it is possible to enter a house number as the destination. DEST. ENTRY CONTINUE INTERSECTION HOUSE NUMBER Subsequent destination input menu, "street" has been entered If you do not want to accept the street as your destination, 1 press the ESC button <. You will return to the speller. Entering a destination ­ house number If you selected the HOUSE NUMBER menu item, the speller will open for you to enter the house number. 1 2 3 Enter the house number using the speller. Switch to the list and select the section containing the destination house number. Press the OK button 8. Navigation begins. Entering a destination ­ house numbers INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 25 DEUTSCH HOUSE NUMBER 1...7 8...15