User manual BOSE 321 GSX

3·2·1 GSX DVD HOME ENTERTAINMENT SYSTEM Français Español English SAFETY INFORMATION Please read this owner's guide Please take the time to follow this owner's guide carefully. It will help you set up and operate your system properly, and enjoy all of its advanced features. Save your owner's guide for future reference. WARNING: To reduce the risk of fire or electric shock, do not expose the system to rain or moisture. WARNING: This apparatus shall not be exposed to dripping or splashing, and objects filled with liquids, such as vases, shall not be placed on the apparatus. As with any electronic products, use care not to spill liquids in any part of the system. Liquids can cause a failure and/or a fire hazard. The CAUTION marks shown here are located on the bottom of your 3·2·1 GSX home entertainment system media center and the rear panel of the Acoustimass module: The lightning flash with arrowhead symbol, within an equilateral triangle, alerts the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle alerts the user to the presence of important operating and maintenance instructions in this owner's guide. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, insert fully. CAUTION: No naked flame sources, such as lighted candles, should be placed on the apparatus. Class 1 laser product CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 LASER LASER LASER LASER PRODUCT PRODUKT LAITE APPARAT The DVD player within the media center is classified as a CLASS 1 LASER PRODUCT according to EN60825-1:1994 + A1+A2, IEC60825-1:1993+A1+A2. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The DVD player should not be adjusted or repaired by anyone except properly qualified service personnel. Class B emissions limits This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Batteries Please dispose of used batteries properly, following any local regulations. Do not incinerate. Additional safety information See the additional instructions on the Important Safety Information sheet enclosed in the shipping carton. 2 English Español CONTENTS Français CONTENTS INTRODUCTION SYSTEM SETUP SYSTEM CONTROLS AND INDICATORS OPERATION CHANGING SOURCE SETTINGS CHANGING SYSTEM OPTIONS MAINTAINING YOUR SYSTEM TROUBLESHOOTING 5 8 26 35 48 53 64 66 INTRODUCTION Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introducing the uMusicTM intelligent playback system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking for region code compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting compatible discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 5 5 5 6 6 7 SYSTEM SETUP Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting locations for your 3·2·1 GSX system components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positioning the media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positioning the speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positioning the Acoustimass® module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Making system connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the Acoustimass module to the media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the speakers to the Acoustimass module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the supplied antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting cable FM radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting your TV to the media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Making audio connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Making composite video connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting your TV and VCR to the media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Option A: TV (with audio output jacks) + VCR + media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Option B: TV (NO audio output jacks) + VCR + media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCR considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Advanced setup options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Making S-video connections (higher quality video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Making component video connections (highest quality video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting digital audio devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting your cable/satellite box, TV, and VCR to the media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting a game console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Verifying your system setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8 9 9 10 11 12 12 12 14 14 15 15 15 16 16 17 18 18 18 19 20 20 22 23 24 25 SYSTEM CONTROLS AND INDICATORS Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting up your remote to control other audio/video devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct entry of a device code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Searching for a device code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Verifying an entered device code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing channel selection control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Media center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 26 30 30 31 33 33 34 3 Français Español English OPERATION Turning your system on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Playing video DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Basic DVD operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Restricting access to video DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Playing audio CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Listening to FM/AM radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tuning to a station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storing stations as presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Erasing a preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the uMusicTM intelligent playback system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storing CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Playing stored music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rating your music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stored music play modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repeat and shuffle functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deleting stored tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using uMusic presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Searching through your music library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Registering your system for music information updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 35 35 36 36 37 38 38 38 38 39 39 40 42 42 42 43 43 45 46 47 CHANGING SOURCE SETTINGS Using the settings menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stored CD settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM/AM settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DVD settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TV, CBL-SAT, and AUX settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 48 50 50 50 51 52 CHANGING SYSTEM OPTIONS Using the System menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stored CD options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Video options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Media center options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote control options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DVD Lock options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 53 54 58 59 60 61 62 MAINTAINING YOUR SYSTEM Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 64 65 65 TROUBLESHOOTING Troubleshooting table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 66 67 TECHNICAL INFORMATION END USER LICENSE AGREEMENT DEVICE CODES 68 69 A-1 4 English Español Français INTRODUCTION Before you begin Thank you for purchasing the 3·2·1 GSX DVD home entertainment system, which offers superb sound, elegance, and simplicity in an advanced home audio setup. Using Bose® proprietary signal processing technology, the 3·2·1 GSX system provides improved spaciousness from stereo recordings, and bold movie effects from surround-encoded materials. Yet its few parts require little effort to set up, so you can enjoy your new system's performance right away. The following items are included to help you set up your system: · Quick Setup Guide · Detailed setup instructions in Setup section of this guide · Setup DVD INTRODUCTION System features · Integrated AM/FM tuner and DVD/CD player in a small media center · uMusicTM intelligent playback system for storing and playing your favorite songs · Small, easy-to-place shelf speakers and an attractive hideaway Acoustimass® module · Easy-to-use universal infrared remote control · Media center input jacks for a TV, cable/satellite box or other component such as a DVR Introducing the uMusicTM intelligent playback system Your 3·2·1 GSX DVD home entertainment system includes the new uMusic intelligent playback system ­ a breakthrough Bose technology that makes it possible to store and enjoy your CD collection. What can you do with this system? · Store your favorite CDs in a music library. Your system can store approximately 200 hours of music or about 200 CDs. · Teach the system which tracks your like or dislike, conditioning the system to automatically play the music you want to hear most. · Discover many ways to enjoy your music. Checking for region code compatibility For a DVD player and DVD disc to be compatible, their region code numbers must match. These numbers are allocated according to where the player and disc are sold. The 3·2·1 GSX DVD home entertainment systems have a region code which must also match the DVD discs. Check the region code number on the carton of the 3·2·1 GSX DVD home entertainment system or on the bottom of the media center that comes in the carton. Then be sure to choose only DVD discs that show the same region number on the disc label or front cover. For example, a Region 1 DVD disc should display the following mark: 5 Français INTRODUCTION Español English INTRODUCTION Selecting compatible discs The DVD/CD player built into the 3·2·1 GSX media center can play the following types of discs identified by their corresponding logos: · Video DVD · Audio CD · Video CD · DVD+R, DVD-R, DVD+RW and DVD-RW · CD-R and CD-R/W · MP3 CDs, where ­ All tracks were burned in a single closed session ­ The disc format is ISO9660 ­ Each file has a ".mp3" extension and the filename contains no other periods · SACDs (CD-compatible content only) Note: Regarding copy protection ­ Music and other content may be protected by international and domestic copyright laws and may contain specific restrictions on use and/or reproduction. Please respect the rights of the artists and other copyright holders. Glossary of terms Aspect Ratio ­ The shape of the rectangular picture in a TV set. It is the width of the picture relative to the height. Our standard TV picture, in terminology used by that industry, is 4 units wide by 3 units high, or 4:3 (read as 4 by 3) in aspect ratio. There are currently two standard TV aspect ratios, 4:3 and 16:9. Chapter ­ In DVD-Video, a division of a title. Component Video ­ A video signal split into three parts: luminance and two color signals (marked as YPbPr). It provides the highest level of video quality. Composite Video ­ A single video signal that contains luminance, color, and synchronization information. NTSC and PAL are examples of composite video systems. Dolby Laboratories ­ Developer of a perceptual coding system for audio. Dolby Digital DTS ­ A type of multi-channel surround sound format used on discs. ­ A type of multi-channel surround sound format used on discs. DVD ­ An acronym that is most commonly known to mean Digital Video Disc or Digital Versatile Disc. The audio/video/data storage system based on 12- and 8-cm optical discs. DVD Video ­ A standard for storing and reproducing audio and video on DVD-ROM discs, based on MPEG video, Dolby Digital and MPEG audio, and other proprietary data formats. 6 English Español Français INTRODUCTION Gracenote ­ Music recognition technology and related data provided as part of the service contracted by Bose. IR ­ An acronym for infrared. Pertains to the type of remote that sends/receives commands on an infrared light beam. MPEG ­ A type of data compression used for audio or video storage on disc. MP3 ­ MPEG-1 Layer III audio. This is a compressed audio format that allows you to record many hours of music on a single CD. NTSC ­ An acronym for National Television System Committee. The organization that developed both the American Black & White and Color television systems. PAL ­ An acronym for Phase Alternate Line. A television format used extensively in Western Europe. Progressive Scan ­ A video format which displays all lines of the picture frame in a single pass, and refreshes the TV image 30x/sec. Not compatible with all video displays. PVR ­ An abbreviation for Personal Video Recording. Sometimes used interchangeably with DVR for Digital Video Recording, but may include non-digital technology, as used in VCRs. RDS ­ A system that displays radio broadcast station and programming information.This feature is available on European systems only. SACD ­ An abbreviation for Super Audio Compact Disc, used for high-resolution digital audio storage on CD-sized discs. New Bose® 3·2·1 GSX systems play the CD-compatible portion of such discs, identified by the CD disc logo on the front of the disc. SCART ­ A type of jack commonly found on consumer electronics products manufactured for use in Western Europe. S-video ­ A video interface standard that carries separate luminance and chrominance signals, usually on a four-pin mini-DIN connector. Also called Y/C. The quality of S-video is significantly better than composite video since it does not require a comb filter to separate the signals. Most high-end televisions have S-video inputs. uMusicTM intelligent playback system ­ A revolutionary Bose play mode, which performs like a virtual DJ by noting listener preferences and playing suitable stored CD tracks in response. Videostage® 5 ­ Bose proprietary Videostage 5 decoding circuitry gives you a five-channel surround sound experience from everything you listen to ­ VHS tapes, stereo CDs, even mono TV programs. INTRODUCTION Limited warranty Your 3·2·1 GSX DVD home entertainment system is covered by a limited transferable warranty. Details of the limited warranty are provided on the product registration card that came with your system. Please fill out the information section on the card and mail it to Bose. Failure to do so will not affect your limited warranty rights. 7 Français Español English SYSTEM SETUP Unpacking SYSTEM SETUP Carefully unpack your system. Save all packing materials, which provide the safest way to transport your system. Check to be sure your system includes the parts shown in Figure 1. If any part of the system appears damaged, do not attempt to use it. Notify Bose or your authorized Bose® dealer immediately. For Bose contact information, refer to the address sheet included in the carton. WARNING: To avoid danger of suffocation, keep the plastic bags out of the reach of children. Figure 1 Contents of the shipping carton Your system includes one of the following cords: Remote control Batteries Media center ® Gemstone® speaker arrays 120 VAC power cord (US/Canada) Acoustimass® module cable Small rubber feet for speaker arrays Speaker cable 115/230 VAC power cord with adapter (US/Europe) Acoustimass module Large rubber feet for Acoustimass module Antenna stand AM antenna Video cable 230 VAC power cord (Europe) Stereo cable 230 VAC power cord (UK/Singapore) FM antenna Setup disc For your records Now is a good time to find the serial numbers on the bottom of the media center and on the rear of the Acoustimass® module. Please record them here and on your Product Registration Card. You will need to have them ready if you ever need to contact Bose® Customer Service. 240 VAC power cord (Australia) Media center serial number: _________________________________________________________ Acoustimass module serial number: __________________________________________________ Dealer name: ______________________________________________________________________ Dealer phone: __________________________ Purchase date: _____________________________ We suggest you keep your sales receipt and product registration together with this owner's guide. 8 English Español Français SYSTEM SETUP Selecting locations for your 3·2·1 GSX system components Use the following guidelines and Figure 2 to choose locations and positions for the components of your 3·2·1 GSX home entertainment system. Note: While these guidelines are offered to help provide great system performance, you may find other placement choices that are more convenient and provide the sound you enjoy. SYSTEM SETUP Positioning the media center CAUTION: Do not block any ventilation openings. For reliable operation of the product and to protect it from overheating, put the product in a position and location that will not interfere with its proper ventilation. For example, do not place the product on a bed, sofa, or similar surface that may block the ventilation openings. Do not put it in a built-in system, such as a bookcase or cabinet that may keep air from flowing through its ventilation openings. · Place the media center where nothing obstructs opening the disc tray on its front panel. · Position the media center close enough to the Acoustimass® module and the speakers so that all the cables will reach. · Make sure the media center is close enough to additional source devices (TV, VCR or cable box) so that all the cables will reach. · Make sure that the front of the media center is unobstructed so that it may receive IR (infrared) commands from the remote control. Figure 2 Sample media center and speaker placement 3 ft (1 m) maximum 3 ft (1 m) minimum 3 ft (1 m) maximum Left speaker Right speaker Media center Note: The left and right speakers are magnetically shielded to prevent interference with your TV screen. 9 Français SYSTEM SETUP Español English Positioning the speakers SYSTEM SETUP Choosing a good location for the speakers will allow you to experience the audio surround effects that your 3·2·1 GSX home entertainment system is designed to deliver. · Place the left and right speakers at least 3 feet (1 meter) apart from each other to optimize the surround sound experience (Figure 3). · Place each speaker within 3 feet (1 meter) of the edge of the TV screen. Placing the speakers more than 3 feet away from the TV can cause the sound to become separated from the picture. · If you are using a bookshelf or a home entertainment unit, place each speaker at the front edge of its shelf Positioning the speakers too far back in an enclosed space can change the overall quality of sound and alter the movie sound effects. CAUTION: Choose a stable and level surface for both speakers. Vibration can cause the speakers to move, particularly on smooth surfaces like marble, glass, or highly polished wood. If you are placing the speakers on a flat surface, be sure to attach one set of the small rubber feet to the bottom surface of each speaker. You can obtain additional rubber feet (PN 178321) from Bose® Customer Service. To contact Bose, refer to the list of offices included in the product carton. Note: The speakers can be mounted on Bose brackets, table stands, or floor stands. For ordering information, refer to "Accessories" on page 65. Additional or longer cables may also be ordered. Figure 3 Recommended speaker placement · Set the speakers on their bottom surfaces, only, with the Bose logo right-side up. · Aim the speakers straight ahead into the listening area. Do not place the speakers at an angle. Angling one or both speakers into or away from the listening area significantly alters system performance. 10 English Español Français SYSTEM SETUP Positioning the Acoustimass® module · Place the module at the same end of the room as the TV and the speakers (Figure 4). SYSTEM SETUP · Keep the module at least 3 feet (1 meter) away from the TV to prevent the module from interfering with the TV screen. · Place the Acoustimass module within reach of the cable from the music center and an AC (mains) power outlet. · Choose a convenient location such as under a table, behind a sofa or chair, or behind drapes, but do not block the port opening. Figure 4 Recommended Acoustimass module placement 3 ft (1 m) minimum · Attach the large rubber feet to the bottom of each foot on the module. The rubber feet provide increased stability and protection from scratches. · Aim the port of the module into the room or along the wall. This prevents a blocked port or over-powering bass. · Stand the Acoustimass module on its feet. Do not lay it on its side or stand it on either end (Figure 5). Figure 5 ACINPU T MUSICC ENTER Recommended orientation of the module CAUTION: Do not block the openings on the back of the module, which provide ventilation for the built-in circuitry. CAUTION: The Acoustimass module generates a magnetic field. Although this is not an immediate risk to your video tapes, audio tapes, and other magnetic media, you should not store any of these items directly on or near the module. 11 Français SYSTEM SETUP Español English Making system connections SYSTEM SETUP CAUTION: Do not plug the Acoustimass® module into an AC power (mains) outlet until all the components are connected. Connecting the Acoustimass module to the media center Plug one end of the Acoustimass module cable into the Acoustimass Module jack on the rear ) jack on the of the media center (Figure 6). Plug the other end of the cable into the input ( rear of the Acoustimass module. Note: The jacks for the Acoustimass module cable are keyed so that the cable connectors only plug in one way. Make sure that the arrow on the connector body faces up when plugging in the cable. Figure 6 Acoustimass module-tomedia center connection Acoustimass module input jack Media center rear panel Acoustimass module cable Acoustimass module rear panel Connecting the speakers to the Acoustimass module 1. Insert the single-plug end of the speaker cable into the SPEAKERS jack on the rear panel of the Acoustimass module (Figure 7). Tighten both screws on the plug. Figure 7 Speaker cable-toAcoustimass module connection Acoustimass module cable Speaker cable Acoustimass module input jack Note: If additional audio cables or longer cables are needed to make these connections, contact Bose Customer Service. Refer to the list of offices included in the product carton. 12 English Español Français SYSTEM SETUP 2. At the other end of the speaker cable, separate the left and right speaker cords as much as necessary to reach each speaker (Figure 8). SYSTEM SETUP Figure 8 Separating left and right speaker cords 3. Plug the LEFT speaker cable into the rear jack of the left speaker (Figure 9). Plug the RIGHT speaker cable into the rear jack on the right speaker. Figure 9 Left and right speaker connections RIGHT speaker cable LEFT speaker cable Note: Make sure cable connectors are fully inserted and seated firmly in the speaker jacks. 13 Français SYSTEM SETUP Español English Connecting the supplied antennas SYSTEM SETUP The rear panel of the media center provides jacks for the AM and FM antennas included with your system (Figure 10). Unwind the wires for each antenna to provide the best reception. Note: An outdoor antenna may be used in place of the supplied indoor antennas. To add an outdoor antenna, consult a qualified installer. Follow all safety instructions supplied with the antenna. Figure 10 Antenna connections FM dipole antenna Media center AM loop antenna FM antenna Plug the FM antenna into the FM jack on the media center rear panel. Spread out the antenna arms and move them around to establish optimum FM reception. Extend the antenna as far from the media center and other equipment as possible. AM antenna Plug the AM loop antenna into the AM jack on the media center rear panel. Place the antenna loop at least 20 inches (50 centimeters) away from the media center and at least 4 feet (1.2 meters) away from the Acoustimass® module. Experiment with positioning the loop for optimum AM reception. Follow the instructions enclosed with the AM loop antenna to stand it on the supplied base, or mount it to a wall. Connecting cable FM radio Some cable TV providers make FM radio signals available through the cable service to your home. This connection is made to the external FM jack on the back panel of the media center. To connect to this service, contact your cable TV provider for assistance. Note: Make sure that the cable radio installation includes a TV/FM splitter so that only the FM radio band, not the cable TV band, is received by the media center. If necessary, contact your cable company. 14 English Español Français SYSTEM SETUP Connecting your TV to the media center If you want to use the 3·2·1 GSX system with both a TV and a VCR, skip this section and go to "Connecting your TV and VCR to the media center" on page 16. SYSTEM SETUP Making audio connections Note: If your TV does not have audio output jacks, see "Option B: TV (NO audio output jacks) + VCR + media center" on page 17. Otherwise, continue. 1. Connect one end of the supplied stereo cable to the TV Audio IN jacks on the rear panel of the media center (Figure 11). Insert the white RCA plug into the TV white L jack. Insert the red RCA plug into the TV red R jack. 2. Connect the other end of the stereo cable to the audio output jacks on your TV. Insert the white RCA plug into the white AUDIO OUT L jack. Insert the red RCA plug into the red AUDIO OUT R jack. Making composite video connections Note: Some older TVs with standard TV cable connectors do not have a composite video or an S-video input. Such TVs are not compatible with any DVD players and require use of an RF modulator for this connection. RF modulators are available at your local electronics store. 1. Insert one end of the supplied video cable (yellow) to the Video OUT C (composite) jack on the back of the media center (Figure 11). 2. Insert the other end of the video cable into one of the video input jacks on your TV. Figure 11 TV (composite video)-tomedia center connections Write the name of the video input jack used on your TV in the box on page 25. After you turn the system on, you will need to select this video input on your TV in order to view the 3·2·1 GSX system video output. Media center rear panel Video cable (yellow connectors) TV connector panel TV Stereo cable (red and white connectors) * 15 Français SYSTEM SETUP Español English Connecting your TV and VCR to the media center SYSTEM SETUP There are two options for connecting your TV and VCR to the media center. · Option A: TV with audio output jacks+VCR · Option B: TV without audio output jacks+VCR Before proceeding, check your TV for audio output jacks. Option A: TV (with audio output jacks) + VCR + media center If your TV has audio output jacks, you can directly route the TV audio to the 3·2·1 GSX home entertainment system (Figure 12). 1. Connect one end of the supplied stereo cable to the TV Audio IN jacks on the rear panel of the media center. Insert the white RCA plug into the TV white L jack. Insert the red RCA plug into the TV red R jack. 2. Connect the other end of the stereo cable to the audio output jacks on your TV. Insert the white RCA plug into the white AUDIO OUT L jack. Insert the red RCA plug into the red AUDIO OUT R jack. 3. Insert one end of the supplied video cable (yellow) to the Video OUT C (composite) jack on the back of the media center. Insert the other end of the video cable into one of the video input jacks on your TV. Figure 12 Option A connections Write the name of the video input jack used on your TV in the box on page 25. After you turn the system on, you will need to select this video input on your TV in order to view the 3·2·1 GSX system video output. Cable/satellite box (if applicable) Cable service VCR Video cable (yellow connectors) TV connector panel Cable service TV Stereo cable (red and white connectors) * 16 English Español Français SYSTEM SETUP Option B: TV (NO audio output jacks) + VCR + media center If your TV does not have audio output jacks, you will need to feed audio to the 3·2·1 GSX home entertainment system through a secondary source, such as a VCR. To do this, you will need one additional video cable, which can be purchased at your local electronics store. 1. Connect one end of the supplied stereo cable to the AUX Audio IN jacks on the rear panel of the media center (Figure 13). Insert the white RCA plug into the AUX white L jack. Insert the red RCA plug into the AUX red R jack. 2. Connect the other end of the stereo cable to the AUDIO OUT jacks on your VCR. Insert the white RCA plug into the white AUDIO OUT L jack. Insert the red RCA plug into the red AUDIO OUT R jack. 3. Insert one end of the supplied video cable (yellow) into the VIDEO OUT jack on the back of your VCR. Insert the other end of the cable into the Video IN C (composite) jack on the back of the media center. 4. Insert one end of the second video cable (yellow) into the Video OUT C (composite) jack on the back of the media center. Insert the other end of the cable into one of the video input jacks on your TV. Figure 13 Option B connections SYSTEM SETUP Write the name of the video input jack used on your TV in the box on page 25. After you turn the system on, you will need to select this video input on your TV in order to view the 3·2·1 GSX system video output. Cable/satellite box Media center rear panel Video cables (yellow connector) Cable service VCR Stereo cable (red and white connectors) VCR connection panel Cable service IMPORTANT If you connected your TV and VCR this way, you will need to turn on your VCR and select the AUX source on the 3·2·1 remote to hear sound from TV programs. TV connection panel TV 17 Français SYSTEM SETUP Español English VCR considerations SYSTEM SETUP · Some combination TV/VCR units may not work with 3·2·1 GSX home entertainment systems. Please refer to your TV/VCR owner's manual for information. · A stereo VCR is required for optimal sound performance. If your VCR has only one audio output, you have a mono VCR. You will need a Y-adapter cable (available at electronics stores) to connect audio to the media center. For this setup, you will need to select "Mono decoding" (see "TV, CBL-SAT, and AUX settings menu" on page 52) so your 3·2·1 GSX system will simulate surround sound effects from a mono source. Otherwise, you will hear mono sound from both speakers. Advanced setup options The 3·2·1 GSX home entertainment system provides connections for producing higher quality video and audio. The following describes how to use these connections. Making S-video connections (higher quality video) An S-video input jack, provided on many TVs, delivers a higher quality TV picture than the composite video output connection shown in Figure 11. For this connection you will need an S-video cable which can be purchased from your Bose dealer or a local electronics retailer. 1. Insert one end of the S-video cable into the S-Video OUT jack on the media center (Figure 14). 2. Insert the other end of the S-video cable into the S-VIDEO IN jack on your TV. Figure 14 TV (S-video)-to-media center connections Media center rear panel IMPORTANT If you use S-video to connect your TV to the media center, you must also use S-video to connect all other devices (such as a cable box and VCR) to the media center. S-video cable TV connector panel TV Stereo cable (red and white connectors) 18 English Español Français SYSTEM SETUP Making component video connections (highest quality video) Note: Component video connections are required in order to use the progressive scan (NTSC only) feature of your 3·2·1 GSX system. Your TV must also support this feature. To turn on the progressive scan feature, see "Video options" on page 59. For the highest quality video from DVDs, you may want to use a component video connection between the media center and the TV. To do so, your TV must provide component video jacks (typically labelled Y, Pb, and Pr). Refer to your TV owner's guide for more information. To make component video connections you will need a component video cable that is long enough to reach from the rear of the media center to your TV (Figure 15). If the cable is not supplied with your TV, you can purchase it separately. 1. On the media center rear panel, plug one end of the component video cable into the Component Y, Pb, and Pr video output jacks (Figure 15). Be sure to match the color of the plug with the color of the jack. 2. Plug the other end of the component video cable into the corresponding (color or letter code) component video jack on the back of your TV. Figure 15 Component video TV-to-media center connections Component video output jacks: Y (green) Pb (blue) Pr (red) SYSTEM SETUP Media center rear panel Component video cable Stereo cable (red and white connectors) TV connector panel (example) IMPORTANT FOR COMPONENT VIDEO USERS Input signals received by the C (Composite) or S-Video IN jacks are not passed through to the Component video OUT jacks. If you connect an external video device to the C or S-Video IN jack, you must also connect the C or S-Video OUT jack on the media center to the respective video input jack on your TV. To view the external video input on your TV, you will need to select the TV video input used for that device. To view the onscreen menus of the 3·2·1 GSX system, you will need to switch back to the TV's component video input. Note: For more information, or to purchase the video cables, contact your local electronics store or authorized Bose dealer. 19 Français SYSTEM SETUP Español English Connecting digital audio devices SYSTEM SETUP Some audio devices feature a digital audio output for optimum sound performance. Use an optical digital cable or a coaxial digital cable, as appropriate, to connect this output to the digital input on the media center. You can purchase the required cables at a local electronics store. On the media center rear panel, an optical digital cable connects to the OPTICAL jack. A coaxial cable connects to the audio input jacks labeled D. Note: Before you can benefit from the optical connection, you will need to assign the optical connector to the audio source in the system settings menu. See "Media center options" on page 60. Figure 16 Media center digital audio input jacks Optical digital audio input Coaxial digital audio inputs Connecting your cable/satellite box, TV, and VCR to the media center The 3·2·1 GSX home entertainment system provides flexibility for you to add up to three external audio devices, including your TV, directly to the media center. Figure 17 shows you an advanced setup using a TV, VCR and cable/satellite box. In this setup, please notice the following: · S-video connections are used to deliver the cable/satellite signal to the media center. Therefore, the media center output video is sent to the TV also through an S-video connection. · Analog and digital coaxial audio connections are shown for the cable/satellite box. As an option, you may use an optical digital connection. However, before you can benefit from the optical connection, you will need to assign the optical connector to the cable/satellite box audio source in the system settings menu. See "Media center options" on page 60. · When connecting an audio device to the media center jacks, remember to match the red jack to the right channel (R) and the white (or black) jack to the left channel (L). · For further details on making the video connections between your VCR and TV, refer to the manuals for these video devices. Note: The recommendations contained in this owner's guide are basic suggestions for connecting external devices to the 3·2·1 GSX system. Instructions and terminology pertinent to these external devices may vary, depending on the manufacturer. Consult the owner's guide that came with the device for clarification on setup and usage before making any connections. 20 English Español Français SYSTEM SETUP Figure 17 Advanced setup example: TV, VCR and cable/satellite box For future use only. SYSTEM SETUP Media center CBL-SAT S-video Cable/satellite (CBL-SAT) service Cable/satellite CBL-SAT analog audio CBL-SAT digital audio CBL-SAT signal to VCR VCR TV CBL-SAT signal to TV VCR analog audio Media center's S-video output to TV Note: For more information on advanced connections, refer to the DVD setup disc that came with your 3·2·1 GSX home entertainment system. 21 Français SYSTEM SETUP Español English Connecting a game console SYSTEM SETUP Connect the audio output of a game console to the AUX Left and Right input jacks. Connect the video output of the game console to the C (composite) Video IN jack. Figure 18 Game console connections Media center Game console connection panel TV connection panel IMPORTANT If you connected your game console this way, you will need to select the AUX source on the 3·2·1 remote in order to hear sound from the game console. 22 English Español Français SYSTEM SETUP Installing the remote control batteries 1. On the back of the remote, slide open the battery compartment (Figure 19). 2. Insert the two supplied AA (IEC-R6) 1.5V batteries, or their equivalent, as shown. Match the plus (+) and minus (­) marked on the batteries with the plus (+) and minus (­) inside the battery compartment. 3. Slide the battery compartment cover back into place. Note: Replace the batteries when the remote control stops operating or its range seems reduced. Figure 19 Installing the batteries SYSTEM SETUP (2) AA batteries (IEC R6) + + Battery compartment cover 23 Français SYSTEM SETUP Español English Connecting the power cord SYSTEM SETUP CAUTION: Do not plug the Acoustimass® module into an AC power (mains) outlet until all the components are connected. CAUTION: For dual voltage models only, be sure to set the dual voltage switch on the back of the Acoustimass module to the appropriate voltage for your area (115V or 230V) before connecting to power. If you are not sure about the proper voltage for your area, consult your local electrical authorities. 1. Insert the small connector end of the power cord into the AC INPUT connector on the Acoustimass module (Figure 20). 2. Insert the large end of the cord into an AC power (mains) outlet. Note: On 220-240V models only, turn the Acoustimass module POWER switch to on (l). Figure 20 Connecting to power AC input jack AC power switch 115/230V selection switch Note: Provided only on 220-240V rated systems Note: Provided only on 115/230V dual voltage rated systems 24 English Español Français SYSTEM SETUP Verifying your system setup 1. Check the following before you continue: · All cables are connected for the setup you chose. · The batteries were installed in the remote control. · The power cord was installed and plugged into a live AC receptacle. 2. Turn on your TV. Use the remote control that came with your TV. 3. Using your TV remote, select the video input on your TV that connects to the video output of the media center. Name TV video input used: · The method of selecting the right video input depends on your TV. Refer to your TV owner's guide for help. 4. Turn off the TV speakers. · Refer to your TV owner's guide for help. · If your TV does not have an option to turn off the internal speakers, you may need to adjust both the 3·2·1 GSX system volume and your TV volume until you find a level that produces the desired sound. · In some TVs, when the internal speakers are turned off, you may need to raise the TV's volume level by 75% to 100% in order to hear audio from the 3·2·1 GSX home entertainment system. See your TV owner's guide for help. 5. Turn on your 3·2·1 GSX system. · Point the 3·2·1 GSX remote control at the media center and press On-Off. 6. Play the 3·2·1 GSX setup DVD. · Press Eject on the media center control panel. · Insert the DVD setup disc into the disc tray. · Press Eject again to close the tray. The DVD will automatically begin to play. If it does not, press the play button ( ). Note: Be sure to play the Setup DVD, included in the carton with your system, as soon as all the connections are completed. This will help you verify the connections you have made and confirm proper sound performance. SYSTEM SETUP 25 Français Español English SYSTEM CONTROLS AND INDICATORS Remote control SYSTEM CONTROLS AND INDICATORS Remote status LED Turns the system on or off. Status LED: · Off (unlit) during normal operation. · On during the process of setting up the remote to control other equipment such as your TV or VCR. Silences or restores the sound from the current source. Selects the Stored CD source and turns the system on to the last-selected uMusicTM intelligent playback system play mode. Selects the built-in CD/DVD player and turns the system on. · Selects the built-in tuner and turns the system on to the previously selected FM/AM station. · Switches between FM and AM when the tuner is selected. TV: Selects the TV sound source and turns your system on. Input: Changes the external input to your TV. For example, your TV might have two external inputs where one is connected to your cable box and the other to your VCR. Pressing this button alternates between the cable box and the VCR.* On/Off: Turns your TV on and off.* CBL-SAT: Selects the CBL-SAT sound source and turns your system on. On/Off: Turns your cable/satellite box on or off.* AUX AUX: Selects the AUX sound source and turns your system on. On/Off: Turns a VCR or PVR that is connected to the AUX jack on or off.* * Requires special remote settings. See "Setting up your remote to control other audio/video devices" on page 30. 26 English Español Français SYSTEM CONTROLS AND INDICATORS Remote control ­ cont. SYSTEM CONTROLS AND INDICATORS Enters the library of stored CD tracks. Displays the Settings menu for the current source on your TV screen or media center display. Displays the System menu on your TV screen. · Displays the DVD menu of the currently loaded DVD disc on your TV screen. · Displays the main menu of a cable/satellite box, VCR, or PVR on your TV screen (if supported).* Displays the TV program guide (if supported) on your TV screen. · Removes the Settings menu, System menu, or Library menu from your TV screen. · Removes the TV program guide (if supported) from your TV screen or media center display. · Tunes the FM or AM radio to the next higher or lower frequency. · Selects the next item, up or down, in menus. Confirms a menu selection or introduces the next level of menu options. Moves up, down, left, or right in onscreen menus and media center displays. *Requires special remote settings. See "Setting up your remote to control other audio/video devices" on page 30. 27 Français SYSTEM CONTROLS AND INDICATORS Español English Remote control ­ cont. SYSTEM CONTROLS AND INDICATORS · Raises or lowers the volume of the current source. · Pressing + restores muted sound from the current source. · Pressing ­ lowers the volume of the current source, but does not restore muted sound. Skips to the next or previous CD track, DVD chapter, radio station preset, or TV channel (if the remote is set up to control your TV). · Stops the disc player. · For DVDs only, the disc stops and the system saves the DVD play posicontinues the DVD from the saved play position. tion. Pressing twice for a disc in play returns to the beginning of the disc. Pressing · Pauses a currently playing disc. · Pressing again (or pressing ) resumes play of a paused disc. · After 20 minutes of no user interaction, the disc player stops and returns to the beginning of the disc to wait for the next command. Starts the disc player. · Skips backward or forward through CD tracks. · Skips backward or forward through DVD chapters. · Seeks backward or forward to the next strongest radio station. Plays audio CD tracks in random order. Press again to cancel. Repeats a CD, CD track, DVD chapter, or DVD title depending on the selected source. Press again to change the repeat mode. · Selects a CD track, DVD chapter, radio station preset, or TV channel. · Selects a uMusic preset for the Stored source. · Allows numerical selection for some menu options. · Displays or dismisses a cable/satellite information window, if supported. · If playing an MP3 CD, displays or dismisses artist and title information on the media center display panel. · Displays information about the stored track that is playing. Skips to the previous TV channel (if supported by your TV or cable/satellite box). 28 English Español Français SYSTEM CONTROLS AND INDICATORS Remote control ­ cont. Selects the uMusicTM intelligent playback system for playing stored music. Overrides any other stored music play mode. · Applies a negative (­) or positive (+) rating to the stored track currently playing. · Pressing ­ immediately selects a new track. · Pressing + continues playing the current track. Selects and plays stored music that most closely matches the style of the current track. Plays the tracks from a CD selected by its number in the uMusic system. Plays all the tracks, if any, assigned to the playlist. Can be used with other play mode options, like Encore. Skips from the track most recently playing to the first track on the CD of origin and plays that CD from beginning to end. SYSTEM CONTROLS AND INDICATORS 29 Français SYSTEM CONTROLS AND INDICATORS Español English Setting up your remote to control other audio/video devices Your remote can be set up to control other audio/video devices such as a TV, VCR, PVR or cable/satellite box by entering a device code while in the setup mode. SYSTEM CONTROLS AND INDICATORS · If you know the device code, follow the instructions under the heading, "Direct entry of a device code" below. Device codes are listed in the back section of this owner's guide and in the System menus under Remote Control options. · If you can't find the device code and want to search the system for it, see "Searching for a device code" on page 31. · If you want to verify the device code you have entered for an audio/video device, see "Verifying an entered device code" on page 33. · If you want to return to a previous device assignment, press and hold the TV button until the remote LED is lit (about 5 seconds). On the remote keypad, enter 977. · If you want to wipe out all assigned codes, press and hold the TV button until the remote LED is lit (about 5 seconds). On the remote keypad, enter 981. Note: More than one code may work with your particular brand of product. If you notice a lack of response or limited functionality after setting up the remote, try a different code. Note: The remote status LED flashes rapidly eight times if you press an invalid key, or enter an unavailable device code. Wait seven seconds for the error to clear and start again. Direct entry of a device code Device codes can be found at the back of this owner's guide or in the System menu under Remote Control options. If you know the device code, you can do the following: To set up the remote to control your TV 1. Turn on both the 3·2·1 GSX system and your TV. 2. Press and hold the TV button until the remote LED is lit (about five seconds). 3. On the remote keypad, enter the four-digit device code for your TV. The LED will turn off temporarily as you press each key. 4. Check that the LED turns off after the code is entered. If the LED blinks, the code is invalid. Try again. 5. Point the remote at your TV and press the TV On-Off button. If your TV does not respond, go back to step 2 and try other codes. If you are still unsuccessful, see "Searching for a device code" on page 31. Note: To set up the remote to control your cable/satellite box 1. Turn on both the 3·2·1 GSX system and your cable/satellite box. 2. Press and hold the CBL-SAT button until the remote LED is lit (about five seconds). 3. On the remote keypad, enter the four-digit device code for your cable/satellite box. The LED will turn off temporarily as you press each key. 30 English Español Français SYSTEM CONTROLS AND INDICATORS 4. Check that the LED turns off after the code is entered. If the LED blinks, the code is invalid. Try again. 5. Point the remote at your cable/satellite box and press the CBL-SAT On-Off button. If your cable/satellite box does not respond, go back to step 2 and try other codes. If you are still unsuccessful, see "Searching for a device code" below. To set up the remote to control your VCR or PVR (such as Tivo or Replay TV) 1. Turn on both the 3·2·1 GSX system and your VCR or PVR. SYSTEM CONTROLS AND INDICATORS AUX 2. Press and hold the AUX button until the remote LED is lit (about five seconds). 3. On the remote keypad, enter the four-digit device code for your VCR/PVR. The LED will turn off temporarily as you press each key. 4. Check that the LED turns off after the code is entered. If the LED blinks, the code is invalid. Try again. AUX 5. Point the remote at your VCR or PVR and press the AUX On-Off button. If your VCR or PVR does not respond, go back to step 2 and try other codes. If you are still unsuccessful, see "Searching for a device code" below. Searching for a device code Use this method if you do not know the code for a device. Note: This is a very time-consuming process. Use it as a last resort. To set up the remote to control your TV 1. Turn on both the 3·2·1 GSX system and your TV. 2. Press and hold TV until the remote LED is lit (about five seconds). 3. Alternately press Channel and TV On-Off until your TV turns off. 4. Press Enter. Check that the remote LED turns off. 5. Point the remote at your TV and press TV On-Off. If your TV does not respond, go back to step 2 and try again. 31 Français SYSTEM CONTROLS AND INDICATORS To set up the remote to control your cable/satellite box Español English 1. Turn on both the 3·2·1 GSX system and your cable/satellite box. SYSTEM CONTROLS AND INDICATORS 2. Press and hold CBL-SAT until the remote LED is lit (about five seconds). 3. Alternately press Channel turns off. and CBL-SAT On-Off until your cable/satellite box 4. Press Enter. Check that the remote LED turns off. 5. Point the remote at your cable/satellite box and press CBL-SAT On-Off. If your cable/ satellite box does not respond, go back to step 2 and try again. To set up the remote to control your VCR or PVR (for example, TiVo or Replay TV) 1. Turn on both the 3·2·1 GSX system and your VCR/PVR. AUX 2. Press and hold AUX until the remote LED is lit (about five seconds). 3. Alternately press Channel and AUX On-Off until your VCR/PVR turns off. AUX 4. Press Enter. Check that the remote LED turns off. AUX 5. Point the remote at your VCR/PVR and press AUX On-Off. If your VCR/PVR does not respond, go back to step 2 and try again. 32 English Español Français SYSTEM CONTROLS AND INDICATORS Verifying an entered device code In case you need to check to see what code the remote is using for a particular device, do the following: 1. Press and hold a source key (TV, CBL-SAT, or AUX) until the remote LED lights (about five seconds) 2. Press the Info button. 3. Press 1 on the remote and count the number of times the LED blinks (zero is indicated by a long blink). This is the first digit. 4. Press 2 on the remote and count the number of times the LED blinks (zero is indicated by a long blink). This is the second digit. 5. Press 3 on the remote and count the number of times the LED blinks (zero is indicated by a long blink). This is the third digit. 6. Press 4 on the remote and count the number of times the LED blinks (zero is indicated by a long blink). This is the fourth digit. 7. Press Exit. SYSTEM CONTROLS AND INDICATORS Changing channel selection control If you are using your 3·2·1 GSX home entertainment system with other audio/video devices, such as a VCR and cable/satellite box, you may wish to change channels using one of these other audio devices rather than your TV. You can easily switch your 3·2·1 remote to change channels on another audio device: 1. Press and hold Last on the 3·2·1 remote. The remote status LED will illuminate and blink the number of times corresponding to the device controlling channel selection. 1 blink = TV 2 blinks = CBL-SAT 3 blinks = AUX 2. After the blinking stops, press the source button (TV, CBL-SAT, or AUX) that corresponds to the device you want to use for channel selection. 3. Press Exit on the 3·2·1 remote. To confirm, press and hold Last on the 3·2·1 remote and count the number of blinks. If the change was made, press Exit. If not, repeat steps 2 and 3. 33 Français SYSTEM CONTROLS AND INDICATORS Español English Media center The media center has a control panel on the top, a display area to show the current status of the system, and a disc tray that opens on the front of the console. SYSTEM CONTROLS AND INDICATORS Control panel The media center has six buttons located above the display. Figure 21 Media center controls Turns system power on or off. Steps through the available source selections. Lowers and raises the volume level. Copies tracks from an audio CD into the music library. Opens or closes the disc tray. On-Off Source ­ Volume + Store Eject ® Note: If you select another source by pressing the Source button, you cannot control the new source with the remote until you press the button for that new source on the remote. Display indicators With the system turned on, the media center display lights up to show the state of the system. Not all possible choices, shown below, light up at once (Figure 22). The display changes with each adjustment or selection you make. Figure 22 Example media center display CD 0:06 TRACK 1/12 SHUFFLE REPEAT DISC TRACK Lights to indicate disc is in play. Lights briefly when a remote control command is received. Indicates shuffle mode is selected for the current disc. Indicates repeat mode is selected for current track or disc.