User manual BOSS 606C

CONTENTS Installation...................................................................................................................3 DIN Front-Mount (Method A)........................................................................................3 Installing the unit ...................................................................................................3 Removing the unit..................................................................................................4 DIN Rear-Mount (Method B).........................................................................................5 Using the Detachable Front Panel ............................................................................6 Wiring Connection......................................................................................................7 Operation ....................................................................................................................8 General Operation .................................................................................................9 Radio Operation ..................................................................................................10 CD Operation.......................................................................................................10 Disc Notes ...........................................................................................................11 Specification .............................................................................................................12 Trouble shooting.......................................................................................................13 2 INSTALLATION Notes: · Choose the mounting location where the unit will not interfere with the normal driving function of the driver. · Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. · Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. · Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. · If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance. 30° · Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONT/REAR-MOUNT This unit can be properly installed either from "Front" (conventional DIN Frontmount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. 182 mm TAKE OUT SCREWS BEFORE INSTALLATION Before install the unit, please remove the two screws. Take out screw before installation DIN FRONT-MOUNT (Method A) Installation Opening This unit can be installed in any dashboard having an opening as show below: 53 mm Installing the unit Be sure you test all connections first, and then follow these steps to install the unit. 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. 2. Disconnect the wire harness and the antenna. 3. Press the release button on the front panel and remove the control panel (see the steps of "remove the front panel"). 4. Lift the top of the outer trim ring then pull it out to remove it. 5. The two supplied keys release tabs inside the unit's sleeve so you can remove it. One key is for the right side and the other is for the left side. Insert the keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit. 3 INSTALLATION Sleeve L Key Outer Trim Ring Front Panel Note: to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard. Spring Washer Metal Strap Mounting Bolt Plain Washer Tapping Screw Hex Nut R Key 6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. Dashboard Tabs 10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel. (see the steps of "install the front panel"). Removing the unit 1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery's negative (-) terminal. 2. Remove the metal strap attached the back of the unit (if attached). 3. Press the release button to remove the front panel. 4. Lift the top of the outer trim ring then pull it out to remove it. 5. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard. Screwdriver Sleeve 7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. 8. Slide the unit into the sleeve until it locks into place. 9. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. 4 INSTALLATION DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Side view showing Screw Holes marked T, N Factory Radio Mounting Bracket Hook Screw Screw Hook Dashboard or Console To fasten the unit to the factory radio mounting brackets. 1. Use a screwdriver to loose the hook's screws on the front left and right sides of the unit and remove the hooks. 2. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side. Note: the outer trim ring, sleeve and the metal strap are not used for method B installation. 5 USING THE DETACHABLE FRONT PANEL REMOVE THE FRONT PANEL 1. Press the REL button on the front panel and pull off the front panel. Precautions when Handling 1. Do not drop the front panel. 2. Do not put pressure on the display or control buttons when removing or installing the front panel. 3. Do not touch the contacts on the front panel or on the main unit body. It may result in poor electrical contact. 4. If any dirt or foreign substances adhered on the contacts, they can be removed with a clean and dry cloth. 5. Do not expose the front panel to high temperatures or direct sunlight in anywhere. 6. Keep away any volatile agents (e.g. benzene, thinner, or insecticides) from touching the surface of the front panel. 7. Do not attempt to disassemble the front panel. Release Button Front Panel 2. Keep front panel into the case. Protective Case Front Panel INSTALL THE FRONT PANEL To install the front panel, insert the panel into the housing and make sure the panel is properly installed. Otherwise, abnormality occurs on the display or some keys will not function properly. 6 WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR FUSE RED IGNITION SWITCH (ACC+) Constant 12 volts GROUND (B­) YELLOW BLACK FUSE (BLACK) AUX IN CABLE Rch RED Lch WHITE FRONT RCA CABLE (BROWN) Rch RED Lch WHITE (GREY) POWER ANTENNA FRONT Lch SPEAKER BLUE REAR RCA CABLE Rch RED Lch WHITE WHITE WHITE/BLACK GREY GREY/BLACK VIOLET VIOLET/BLACK FRONT Rch SPEAKER REAR Lch SPEAKER GREEN GREEN/BLACK REAR Rch SPEAKER 7 OPERATION LOCATION OF KEYS 20 1 3 12 13 5 19 17 496 10 21 7 8 14 15 16 2 18 11 22 8 OPERATION GENERAL OPERATION · ON/OFF Switch on the unit by pressing any button (except REL button (6) and button (4)). When system is on, press POWER button (1) to turn off the unit. · FACEPLATE RELEASE Press REL button (6) to detach the removable faceplate. · LOUDNESS For the unit with two bands only: Press and hold BND/LOU button (8) for several seconds to show the loudness state. And shortly press it again to turn on/off the subwoofer output. In CD mode or AUX mode, press BND /LOU button (8) shortly to show the loudness state. And shortly press it again to turn on/off the bass output. · SET THE CLOCK Press DSP button (9) shortly to switch display mode according to display priority set mode. Press and hold DSP button (9) for several seconds until the clock is shown on the display and flashes, then press VOL+/- button (20)(21) to change hours or the minutes. · SELECT AUDIO MODE Press SEL/MENU (3) shortly to change audio mode through volume, bass, treble, balance, and fader modes. Press the VOL+/- button (20)(21) to adjust the selected mode. When the currently displayed function has not been adjusted for several seconds, the mode shall return to volume position and display will return to normal radio, CD or AUX display. Volume Bass Treble Balance Fader Press the VOL+/- (20)(21) to select your setting. BEEP ON/OFF Program power on volume level CLOCK ON/OFF while power off 12hours/24hours CLOCK/FREQ priority · MENU SELECTION FUNCTION Hold press SEL/MENU (3) for several seconds and you will enter the menu functions then press the SEL/MENU button to select the different modes. 9 BEEP ON/OFF - When the beep is on. It will beep with every button you press. - When the beep is turned off. It will not beep when you push a button. Program power on volume level In this mode, you can set the desired volume level when the unit turns on. CLOCK ON/OFF while power off In this mode, you can select if the clock is to be displayed while power off. NO PRI/CLOCK/FREQ priority - When select No Priority: When the frequency appears on the unit, pressing DSP button (9) will display clock and it will not return to frequency display until DSP button (9) pressed again. When the clock appears on the unit, pressing DSP button (9) will display frequency information. - When select Clock Priority: The clock will appear on the unit all the time. Pressing DSP button (9) while in Clock Priority will temporarily display selected station frequency (in RADIO mode) or track number (in CD mode) and then returns to clock display. - When select Frequency Priority: The frequency will appear on the unit all the time. Pressing DSP button (9) while in Frequency Priority will temporarily display clock and then returns to frequency display. 12hours/24hours In this mode, you can set 24 hours mode or 12 hours mode. When the currently displayed function has not been adjusted for several seconds, it will exit menu set mode. · MUTE In radio and AUX mode, press OPERATION (MUT) button (2) to mute the audio output. Press it again to release this mode and recover previous volume level. · EQUALIZATION Press EQ button (10) shortly to turn on equalization function and to select desired audio mode. There are five kinds of mode as below: FLAT CLASS POP M ROCK M RADIO OPERATION · SWITCHING TO RADIO MODE Press MODE button (7) to select radio mode, the radio mode appears in the display together with the memory band. · BAND For the unit with two bands only, press BND/LOU button (8) shortly to change bands as below: FM AM · SELECT MODE Press MODE button (7) repeatedly to select among the following sources: TUNER CD AUX · SELECT STATION Rotate TUNING knob (11) clockwise or counter-clockwise to adjust the frequency upward or downward. · LOCAL/DISTANT Press the LOC button (12) to select between local setting for reception of strong station and distant setting for reception of weak stations when tuning. · MONO/STEREO In FM band, press MON button (13) shortly to select mono or stereo reception for radio stations. You can sometimes improve reception of distant stations by selecting mono operation. CD OPERATION · SWITCHING TO CD MODE If there is no CD inserted in the driver: Gently insert the CD with the printed side up into the disc slot (5) until you feel some resistance. The CD is drawn into the driver automatically. CD playback begins. If a CD is already inserted in the driver: Keep pressing MODE button (7) shortly until the CD mode display appears. · EJECTING A DISC Press button (4) to stop CD play and eject CD from slot. Receiver switches to radio operation. 10 If no CD is present, CD mode will be skipped. · LIQUID CRYSTAL DISPLAY The LCD (19) can show the current state of the unit. · RESET FUNCTION RESET button (22) must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display. Note: If you press the RESET button (22), and the does not come back on, then use a cotton swab soaked in isopropyl alcohol to clean the socket on the front of the panel. OPERATION · PAUSING CD Press button (2) shortly to pause CD player. Press it shortly again to resume playback. · SELECTING TRACKS Press T-UP button (17) or T-DN button (18) to choose the following track or the previous track. Track numbers show on display. Hold T-UP button (17) or T-DN button (18) for several seconds to fast forward or fast reverse. Release the button to stop fast playing. · REPEATING THE SAME TRACK Press RPT button (15) to continuously repeat playing the current track. Press it again to release this mode. · PREVIEWING ALL TRACKS Press SCN button (14) to play first several seconds of each track. Press it again to stop intro and listen to track. · PLAYING ALL TRACKS IN RANDOM Press SHF button (16) to play all tracks in random order. Press it again to cancel the function. DISC NOTES: A. Notes on discs: 1. Attempting to use nonstandard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape etc., onto the label side or the recording side of any discs, as it may cause a malfunction. 3. Dirt, dust, scratches and warping discs will cause misoperation. B. Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable CDs) (For With CDRs/CD-RWs Operation Version Only): 1. Be sure to use discs with following marks only for the unit to play: Recordable Rewritable 2. The unit cannot play a CD-R and CD-RW that is not finalized. (Please refer to the manual of your CD-R/CD-RW recorder or CD-R/ CD-RW software for more information on finalization process). 3. Depending on the recording status, conditions of the disc and the equipment used for the recording, some CD-Rs/CD-RWs may not be played on this unit. (See *1) *1:To have more reliable play back, please see following recommendations: a. Use CD-RWs with speed 1x to 4x and write with speed 1x to 2x. b.Use CD-Rs with speed 1x to 8x and write with speed 1x to 2x. c. Do not play a CD-RW which has been written for more than 5 times. 11 SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 163 (D) x 50 (H)mm : : : : ± 7dB ± 7 dB 40W x 4 (ch) 15 Amps. (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 40 dB : 50 Hz - 15 KHz RADIO Frequency Coverage IF Sensitivity (S/N = 30 dB) Stereo Separation : : : : FM 88 to 108 MHz 10.7 MHz 15 V > 25 dB Frequency Coverage IF Sensitivity (S/N = 20 dB) AM : 530 to 1710 KHz : 450 KHz : 38 dBu 12 TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Cause The car ignition switch is not on. Solution If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to "ACC". Replace the fuse. Remove the disc in the player, then put a new one. The fuse is blown. Disc cannot be loaded or ejected. Presence of CD disc inside the player. Inserting the disc in reverse Insert the compact disc with direction. the label facing upward. Compact disc is extremely dirty or defective disc. Temperature inside the car is too high. Condensation. No sound. Volume is in minimum. Wiring is not properly connected. Sound skips. The installation angle is more than 30 degrees. The disc is extremely dirty or defective disc. The operation keys The built-in microcomputer do not work. is not operating properly due to noise. The radio does not work. The radio station automatic selection does not work. The antenna cable is not connected. The signals are too weak. Clean the disc or try to play a new one. Cool off or until the ambient temperature return to normal. Leave the player off for an hour or so, then try again. Adjust volume to a desired level. Check wiring connection. Adjust the installation angle less than 30 degrees. Clean the compact disc, then try to play a new one. Press the RESET button. Front panel is not properly fixed into its place. Insert the antenna cable firmly. Select a station manually. 13 88-C2184-12