User manual BOSTON ACOUSTICS 361 - Installation Instruction

NCB5 NCB6 NCB8 NCBTL5 NCBTL8 NEW CONSTRUCTION BRACKETS for Boston Acoustics Designer Series Flush Mount Speakers INSTALLATION INSTRUCTIONS The New Construction Bracket is a mounting frame to simplify the installation of Boston Acoustics Designer speakers. Because the bracket is mounted prior to the wallboard installation, it allows the installer to pick locations free from obstructions. The bracket attaches to exposed studs or beams and provides a guide for the wallboard installer. It can be used in ceilings and walls. opposite wings NCB opposite wings 90° NCB 90° speaker wire tie-downs NCB excess wing NCB speaker wire tie-downs Horizontal Mounting Vertical Mounting New Construction Installation (Wall or Ceiling Mount): 1. Determine the desired mounting orientation (horizontal or vertical) and the orientation of the studs or beams. 2. The bracket may be mounted with the flange pointed either towards the wall or towards the room.* a. When the flange is pointing towards the wall, the wallboard can be laid flat to the mounted bracket. The bracket forms a template for cutting the wallboard. Finished opening should align with the bracket opening. b. When the flange is pointed towards the room, the wallboard needs to be measured and cut prior to installation. Finished opening should align with the edges of the new construction bracket's flange. 3. Select two wings opposite each other. Using nails or drywall screws, attach the two wings to the joists or studs so that the wings are 90° to the bracket. There will be some play in the bracket to allow for minor adjustments or leveling. 4. Attach the remaining wings at an angle. This will lock the bracket into position. 5. Bend "speaker wire tie-down tab" inwards, and secure to speaker wire with a cable tie. 6. Cut off excess wing or bend it into the empty stud bay. 361 and 381 Mounting Note: When mounting either a model 361 or 381 Boston Acoustics in-wall speaker into walls 5/8 inch or thicker, be sure to reverse the mounting frame from its normal position as shown to the right. This will allow the speaker's mounting frame to clear the opening and not interfere with the New Construction Bracket. mounting frame in normal position speaker speaker mounting frame in reversed position *NCB5,NCB6, NCB8: Behind the wall there must be 11/2 inches (38.1mm) clearance on the two short sides of the cut-out. *NCBTL5, NCBTL8: Behind the wall there must be 11/2 inches (38.1mm) clearance on the two long sides of the cut-out. Cover5 Cover6 Cover8 Cover5R Cover6R Cover8R COVER PLATE for Boston Acoustics Designer Series Flush Mount Speakers The Cover Plate is a blank plate that covers a pre-cut hole for the installation of a Boston Acoustics Designer Series flush-mount speaker. The Cover Plate may also be used with a Boston Acoustics New Construction Bracket. The Cover Plate can be painted or wall papered to match the wall or ceiling color. The Cover Plate is ideal when: 1. A house has been pre-wired and the speakers have not yet been purchased. 2. The user moves and wants to take the speakers with them. 3. An installation has been delayed and a temporary cover is needed. Installation: 1. Loosely attach the bracket bar to the Cover Plate as shown with provided screws. 2. Bring bar to a minimum 2'' gap (or as necessary to just fit over wall-board). 3. Insert the Cover Plate and bracket assembly into the opening as shown. 4. Tighten the screws, compressing the bar and Cover Plate to the wall. Do not over tighten. Leave minimum 2'' gap 1 2 3 New Construction Bracket Cover Plate Speaker Models NCB5 NCB6 NCB8 NCBR5 NCBR6 NCBR8 NCBTL5 NCBTL8 Cover5 Cover6 Cover8 Cover5R Cover6R Cover8R 351 251 VRi560 VRi580 336pt VRi565 361, 261 381 335, 315 VRi585 - - VRi553 VRi593 DXPRO VRiSub82 300 Jubilee Drive, Peabody, MA 01960 978-538-5000 Fax: 978-538-5199 Covered by patents issued and/or pending. Specifications subject to change without notice. Boston and Boston Acoustics are registered trademarks of Boston Acoustics, Inc. © 2001 Boston Acoustics, Inc. All rights reserved. 042-001325-3