BH-200 User Manual Introduction Thank you for purchasing the BRIOTM BH-200. This headset is designed for use with Bluetooth enabled phones and provides comfortable and convenient wireless communication. Included with the BH-200 is an AC wall charger (QTC-BH200). The BH-200 offers the following features: 6 5 1 7 5. Charger Connection ­ For charging the headset's internal battery. 6. Headset Speaker ­ Directs caller's voice into your ear. Removable speaker cover has 15 mm diameter. 7. Earhook ­ Attaches to headset below speaker. Position over / behind your ear to hold headset in place. See section Adjusting For Use On Either Ear. 8. Microphone ­ Picks up your voice during a call. 9. Optional Speaker Cover ­ The extra speaker cover is 18 mm in diameter. This larger size cover can be used if the 15 mm cover (installed on headset at factory) feels too loose in your ear. Action / Condition Headset is switched on (power on) Headset is switched off (power off) Status LED Illuminates blue for 1 second Illuminates red for 1 second Briefly flashes blue every 5 seconds Headset Speaker Beeps once Beeps once N/A Charging The Internal Battery Important: Before initial use, charge the BH-200's internal battery for 2 hours. Only charge with the QTC-BH200 supplied or other approved chargers. When fully charged, the battery will provide up to 8 hours of talk time and 200 hours of standby time. For best battery performance, use and store the BH-200 at temperatures between 0º and 45º C (32º and 113º F). The internal battery is not replaceable. The battery may be charged and discharged hundreds of time, but will eventually wear out. Recycle the battery when it no longer holds a charge. Do not dispose of headset or battery as household waste. Connect the small end of the QTC-BH200 cable to the headset's charger connec Plug the other end into a wall outlet (AC 120V / 220V). While BH-200 is charging, When the headset is fully charged, Status LED is off. Unplug the charger from the head- tion (see callout 5). the Status LED is red. set and the wall outlet. Do not leave a fully charged battery connected to the charger. Switching The Headset On / Off 3 4 Front Back 9 2 1. Power / Call Button Turns headset on / off. Answers an incoming call when pressed briefly. Ends a current call when pressed briefly. Rejects an incoming call when pressed two times. Headset is switched on, but is not paired or does not have an active connection with a phone (connectable) Headset and phone are connected (connection active) Headset is waiting to be paired with a phone (ready for pairing) Incoming call Call ended Headset connected to charger and charging not complete Headset connected to charger and charging complete Battery charge level is low To switch on, press and hold the Power / Call Button for 2 seconds. The headset beeps once and the Status LED illuminates blue for about 1 second. When the headset is switched on the first time, press and hold the Power / Call Button for 5 seconds. To switch off, press and hold the Power / Call button for 2 seconds. The headset beeps once and Status LED momentarily flashed red. 8 Double flashes blue every 8 seconds Flashes in blue / red pattern for about 3 minutes Flashes blue three times per second N/A Illuminates red while battery is charging No illumination Flashes quickly (about one time per second) with color dependent on headset status Flashes blue / red alternately every 5 seconds N/A N/A N/A Beeps once N/A N/A Beeps once every 20 seconds Pairing Headset To A Phone 2. Status LED / Beeps Power On ­ LED illuminates blue for 1 second (along with 1 beep). Power Off ­ LED illuminates red for 1 second (along with 1 beep). Ready For Pairing ­ LED flashes with blue / red pattern for about 3 minutes or until BH-200 is connected to a compatible phone. BH-200 changes to Connectable if not paired within 3 minutes. Connectable ­ LED flashes blue every 5 seconds until paired to a phone or until there is an active connection with your phone. Connection Active ­ LED double flashes blue every 8 seconds. Incoming Call ­ LED flashes blue three times per second. Call Ended ­ Single beep. Low Battery ­ LED flashes about one time per second and headset beeps every 20 seconds. 3. Volume Up Button ­ Increases audio level from headset speaker. 4. Volume Down Button ­ Decreases audio level from headset speaker. Pairing is the process of linking BH-200 to a Bluetooth enabled phone. The BH-200 may be paired with up to 8 Bluetooth enabled phones, but used with only one phone at a time. The pairing process must be completed with each phone you want to use. Charge the BH-200's internal battery, then follow these steps to pair the headset to your phone: 1. Switch on BH-200 and your Bluetooth enabled phone. BH-200 must be within 30' of the phone for pairing to be completed. 2. Press the Volume Up and Volume Down Buttons simultaneously for 2 seconds. When the Status LED flashes in a blue / red pattern, release the buttons. BH-200 is in pairing mode. 3. Activate the Bluetooth feature on your phone. Set the phone to search for Bluetooth devices. See your phone's user manual for more detailed instructions. 4. Select BRIO BH-200 from the list of displayed devices. 5. Enter pass code 0000 to pair and connect BH-200 to your phone. Note: Some phones pair first, then connect. See user manual for phone. 6. When connected, BH-200 beeps once and the Status LED double flashes blue every 8 seconds. BH-200 is ready to be used with your phone. Number called is busy N/A Erasing Information For All Paired Phones Switch BH-200 on while your Bluetooth phone is off. BH-200's status should be Connectable (LED flashes blue every 5 seconds). Press and hold the Volume Up Button for 5 seconds. When the headset beeps, release the button. The beep confirms that pairing information for all phones has been erased. Answering / Ending A Call ­ When receiving a call, the ring tone is heard through the headset speaker. To answer a call, briefly press the Power / Call Button on BH-200 or the answer key on your phone. If you do not want to answer the call, press the Power / Call Button two times. To end a call, briefly press the Power / Call Button on BH-200 or the end key on your phone. Adjusting The Headset Speaker Volume ­ Press the Volume Up Button to increase audio level or the Volume Down Button to decrease audio level. Switching A Call Between Headset / Phone ­ During the call, press the Power / Call Button and Volume Down Button simultaneously for 2 seconds, or use the respective function in your phone. Switching Between A Current / Waiting Call ­ To switch from your current call in progress to a waiting call, press and hold the Volume Up Button for about 2 seconds, or use the respective function in your phone. Muting The Microphone ­ To mute or unmute the microphone during a call, press and hold the Power / Call Button and Volume Up Button simultaneously for 2 seconds. A beep is provided every 5 seconds to advise that the microphone has been muted. Troubleshooting If the headset is not functioning, it may be necessary to reset BH-200. To reset the headset, press and hold the Volume Up Button and connect the QTC-BH200 charger to the headset. Once the QTC-BH200 is connected, continue to hold the Volume Up Button for 2 seconds to complete the reset. If you cannot connect BH-200 to your phone, make sure the headset is charged, switched on, and paired to a Bluetooth enabled phone. Also, ensure that the Bluetooth feature is activated on your phone, that the headset and phone are in close proximity (maximum 30 feet without obstruction), and that there is no interference from other electronic devices. Disconnecting Headset From A Phone The headset can be disconnected from your phone by: Using the Power Button to switch off BH-200. Disconnecting BH-200 in the Bluetooth menu of your phone. Moving BH-200 more than 30' away from your phone. Note: You do not need to delete the pairing to disconnect the headset from your phone. Headset Care Reconnecting Headset To A Paired Phone Use and store the BRIO BH-200 at room temperature and in dust / dirt free environments. Keep headset dry and away from moisture and humidity. Do not drop, shake, or handle headset in a rough manner. Clean only with a damp cloth and mild detergent. Switch on BH-200 within 30' of your (last connected) phone and it will connect automatically. Your phone must also be switched on and its Bluetooth function enabled. If BH-200 does not connect automatically, check to make sure the headset and phone are paired. If BH-200 is moved more than 30' from the phone, the headset is out of range and will disconnect from the phone. A warning beep is provided when the headset moves out of range of the phone. If BH-200 moves back into range within 10 minutes, it will automatically reconnect. When BH-200 is out of range for more than 10 minutes, its status changes to Connectable (LED flashes blue every 5 seconds). The BH-200 will not automatically connect to the phone when its status is Connectable, even if moved within 30' of the phone. To reconnect, simply switch the headset off, then switch back on. You can also reconnect by using the phone's Bluetooth menu. If BH-200 is switched on within 30' of two or more paired phones, it will attempt to connect with the last connected phone. If a connection is not made with the last connected phone within 20 seconds, BH-200 remains Connectable. Warranty Adjusting For Use On Either Ear The BH-200 may be used with or without the earhook, based on your preference. If you choose to use BH-200 without the earhook, simply position the headset speaker in your left or right ear. Whether placed in your left or right ear, the microphone end should be angled toward your mouth. To use BH-200 with the earhook, it must first be attached to the headset. The earhook snaps in place on the headset below the speaker. To remove the earhook, hold it near the headset and pull gently. If you want to use the earhook and wear the headset on your right ear, attach the earhook as shown in the illustration marked R. If you want to use the earhook and wear the headset on your left ear, attach the earhook as shown in the illustration marked L. The earhook is flexible and can be adjusted to fit tightly of loosely around your ear, while holding the headset securely against your ear. HT Mobile Products, Inc. (HTMP) warrants this product to be free from defects in workmanship and materials for 12 months from date of retail purchase. This warranty applies to the original purchaser and is void if the product has been altered, misused, damaged, neglected, purchased outside the United States, or if repair is required because of normal wear and tear. This is the only warranty made by HTMP. In no event will HTMP, its affiliates, subsidiaries, related entities, or their respective directors, officers, or employees, be liable for any damages beyond repair or replacement as described above, including without limitation, indirect, incidental, or consequential damages. For service under warranty, return the product along with dated proof of purchase to the retailer where purchased or to HT Mobile Products. If returning directly to HT Mobile Products, follow these instructions: 1. Send to HT Mobile Products ­ Warranty Service Department, 2170 Brandon Trail, Alpharetta, GA 30004. For your protection, we recommend you obtain proof of delivery for your shipment. 2. Include with your product, dated proof of purchase, your name and daytime telephone number, and return address (street address only; return shipments cannot be made to a P.O. Box). 3. All items sent become the property of HT Mobile Products and will not be returned. R Calling Features Making A Call ­ With BH-200 connected to your phone, enter a telephone number and place the call using your phone in the normal manner. If your phone supports last number redialing with the headset, press and hold the Volume Up Button for 2 seconds. If your phone supports voice dialing with the headset, press and hold the Volume Down Button for about 2 seconds, or until you hear a tone prompting you to start the voice tag. Your phone should then play the voice tag and dial the requested phone number. To activate either feature, a call may not be in progress. L BRIO BH-200 is compliant with Bluetooth specification 2.0 and supports hands-free profile 1.5 and headset profile 1.1. ©2007 HT Mobile Products, Inc. BRIO is a trademark of HT Mobile Products, Inc. All rights reserved. Printed in China. ...