Brother Laser Printer HL-6050 HL-6050D HL-6050DN User's Guide For visually-impaired users You can read this manual with Screen Reader `text-to-speech' software. You must set up the hardware and install the driver before you can use the printer. Please use the Quick Setup Guide to set up the printer. You can find a printed copy in the box or view it on the CD-ROM we have supplied. Please read this User's Guide thoroughly before you use the printer. Keep the CD-ROM in a convenient place so you can use it quickly if you need to. Please visit our web site at http://solutions.brother.com where you can get answers to Frequently Asked Questions (FAQs), Product Support and Technical Questions, and the latest Driver Updates and Utilities. Version 1 Definitions of warnings, cautions, and notes We use the following terms throughout this User's Guide: You must follow these warnings to prevent possible personal injury. You must follow these instructions to make sure you use the printer properly and do not damage it. Remember these useful tips when you use the printer. i To use the printer safely After you have just used the printer, some parts inside the printer will be extremely hot. When you open the front or back cover of the printer, never touch the shaded parts shown in the illustrations below. The fuser unit is marked with a caution label. Please do NOT remove or damage the label. There are high voltage electrodes inside the printer. Before you clean the printer, clear a paper jam or replace parts, make sure you have turned off the power switch and unplugged the printer from the AC power outlet/socket. Do not handle the plug with wet hands - it might give you an electrical shock. Caution Use neutral detergents for cleaning. Cleaning with volatile liquids such as thinner or benzene will damage the surface of the printer. Do not use cleaning materials that contain ammonia. They will damage the printer and the toner cartridge. ii Trademarks The Brother logo is a registered trademark of Brother Industries, Ltd. Apple, the Apple Logo and Macintosh are registered trademarks in the United States and other countries, and TrueType is a trademark of Apple Computer, Inc. Epson is a registered trademark and FX-80 and FX-850 are trademarks of Seiko Epson Corporation. Hewlett Packard is a registered trademark and HP LaserJet 6P, 6L, 5P, 5L, 4, 4L 4P, III, IIIP, II, and IIP are trademarks of Hewlett-Packard Company. IBM, IBM PC, and Proprinter are registered trademarks of International Business Machines Corporation. Microsoft, MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation in the U.S. and other countries. PostScript is a registered trademark of Adobe Systems Incorporated. ENERGY STAR is a U.S. registered mark. SuSE is a registered trade mark of SuSE Linux AG. Linux is a registered trade mark of Linus Torvalds. RED HAT is a registered trade mark of Red Hat. Inc. Mandrake is a registered trade mark of Mandrake Soft SA. All other terms and brand and product names mentioned in this User's Guide are registered trademarks of their respective companies. Compilation and Publication Notice Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the latest product's descriptions and specifications. The contents of this manual and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication. ©2003 Brother Industries Ltd. Shipment of the Printer If for any reason you must ship your Printer, carefully package the Printer to avoid any damage during transit. It is recommended that you save and use the original packaging. The Printer should also be adequately insured with the carrier. iii Table of Contents Definitions of warnings, cautions, and notes .....................................................................................i To use the printer safely ...................................................................................................................ii Trademarks ..................................................................................................................................... iii Compilation and Publication Notice ................................................................................................. iii Table of Contents ............................................................................................................................iv 1 About this printer .................................................................................................................................... 1-1 What is in the box? ....................................................................................................................... 1-1 Interface cable .................................................................................................................... 1-1 Front view ............................................................................................................................... 1-2 Back view ............................................................................................................................... 1-3 Positioning the printer ................................................................................................................... 1-4 Power supply .......................................................................................................................... 1-4 Environment ........................................................................................................................... 1-4 What kind of paper can I use? ...................................................................................................... 1-5 Type and size of paper ........................................................................................................... 1-5 Recommended paper ............................................................................................................. 1-7 Printable area ......................................................................................................................... 1-8 Printing methods ......................................................................................................................... 1-10 Printing on plain paper .......................................................................................................... 1-10 Printing on plain paper from the paper tray ...................................................................... 1-10 Printing on plain paper from the multi-purpose tray (MP tray) .......................................... 1-13 Printing on thick paper, labels and card stock ...................................................................... 1-16 Printing on envelopes ........................................................................................................... 1-21 Types of envelopes to avoid ............................................................................................. 1-21 Printing on envelopes from the MP tray .......................................................................... 1-23 Printing on transparencies .................................................................................................... 1-28 Printing on transparencies from the paper tray ................................................................ 1-28 Printing on transparencies from the MP tray .................................................................... 1-31 Printing on both sides of the paper ....................................................................................... 1-35 Manual duplex printing from the paper tray (For PCL printer driver) ................................ 1-35 Manual duplex printing from the multi-purpose tray ......................................................... 1-36 Automatic duplex printing (available for HL-6050D and HL-6050DN only) ...................... 1-37 Booklet printing (for the PCL printer driver) (available for HL-6050D and HL-6050DN only) .. ...................................................................................................................................... 1-39 Guidelines for printing on both sides of the paper ............................................................ 1-40 Carbon copy printing ............................................................................................................ 1-42 Driver and software ................................................................................................................................ 2-1 Printer driver ................................................................................................................................. 2-1 For Windows® ......................................................................................................................... 2-2 Features in the PCL printer driver ...................................................................................... 2-2 Features in the BR-Script printer driver (PS printer driver) .............................................. 2-10 For Macintosh® ..................................................................................................................... 2-16 Software (Windows® users) ........................................................................................................ 2-19 Software for Networks .......................................................................................................... 2-19 BRAdmin Professional ..................................................................................................... 2-19 Driver Deployment Wizard ............................................................................................... 2-19 Web BRAdmin .................................................................................................................. 2-19 Automatic emulation selection .............................................................................................. 2-20 Automatic interface selection ................................................................................................ 2-20 Printer settings ............................................................................................................................ 2-21 Factory settings .................................................................................................................... 2-21 2 iv 3 Control panel ........................................................................................................................................... 3-1 Control panel ................................................................................................................................ 3-1 Buttons ......................................................................................................................................... 3-2 Go button ................................................................................................................................ 3-2 Job Cancel button ................................................................................................................... 3-2 Reprint button ......................................................................................................................... 3-3 Reprinting from RAM .......................................................................................................... 3-3 Reprinting the last job ......................................................................................................... 3-3 Printing Proof data .............................................................................................................. 3-4 Printing Public data ............................................................................................................ 3-5 Printing Secure data ........................................................................................................... 3-5 + or - button ............................................................................................................................ 3-7 To move through menus on the LCD ................................................................................. 3-7 To enter numbers ............................................................................................................... 3-7 Back button ............................................................................................................................. 3-7 Set button ............................................................................................................................... 3-7 Light-emitting diode (LED) ............................................................................................................ 3-8 Data - Orange LED ............................................................................................................. 3-8 Liquid Crystal Display (LCD) ........................................................................................................ 3-9 Back light ................................................................................................................................ 3-9 LCD message ....................................................................................................................... 3-10 Printer status messages ................................................................................................... 3-10 How to use the control panel ................................................................................................ 3-11 Control Panel LCD menu ...................................................................................................... 3-13 INFORMATION ................................................................................................................ 3-14 PAPER ............................................................................................................................. 3-15 QUALITY .......................................................................................................................... 3-15 SETUP ............................................................................................................................. 3-16 PRINT MENU ................................................................................................................... 3-17 NETWORK (only on a Network) ....................................................................................... 3-20 INTERFACE ..................................................................................................................... 3-21 RESET MENU .................................................................................................................. 3-21 Set IP Address ................................................................................................................. 3-22 About emulation modes ........................................................................................................ 3-23 HP LaserJet Mode ............................................................................................................ 3-23 BR-Script 3 Mode ............................................................................................................. 3-23 EPSON FX-850 and IBM Proprinter XL Mode ................................................................. 3-23 List of factory settings ........................................................................................................... 3-24 Network factory default setting ......................................................................................... 3-24 For visually-impaired users ......................................................................................................... 3-28 Buzzer indications ................................................................................................................ 3-28 Braille symbols ..................................................................................................................... 3-29 Options .................................................................................................................................................... 4-1 Optional accessories and supplies ............................................................................................... 4-1 Lower tray unit (LT-6000) ....................................................................................................... 4-2 Network board (NC-6100h) (For HL-6050 and HL-6050D) .................................................... 4-3 Installing the network board ............................................................................................... 4-3 Wireless print server (NC-7100w) .......................................................................................... 4-6 Installing the network board ............................................................................................... 4-6 CompactFlash® card .............................................................................................................. 4-9 Inserting the CompactFlash® card .................................................................................... 4-10 DIMM .................................................................................................................................... 4-11 Installing additional memory ............................................................................................. 4-12 Optional fonts package ......................................................................................................... 4-15 Selecting the optional fonts .............................................................................................. 4-15 4 v 5 Routine maintenance .............................................................................................................................. 5-1 Replacing the consumable items .................................................................................................. 5-1 Toner cartridge ....................................................................................................................... 5-2 TONER LOW Message ...................................................................................................... 5-2 TONER LIFE END message .............................................................................................. 5-2 Replacing the toner cartridge ............................................................................................. 5-3 Drum unit ................................................................................................................................ 5-8 CHANGE DRUM SOON message ..................................................................................... 5-8 Replacing the drum unit ..................................................................................................... 5-8 Replacing Maintenance Parts ..................................................................................................... 5-13 Maintenance Messages ................................................................................................... 5-13 Cleaning ..................................................................................................................................... 5-14 Cleaning the outside of the printer ........................................................................................ 5-14 Cleaning the inside of the printer .......................................................................................... 5-15 Cleaning the corona wire ...................................................................................................... 5-17 Troubleshooting ...................................................................................................................................... 6-1 LCD messages ............................................................................................................................. 6-1 Error messages ...................................................................................................................... 6-1 Maintenance messages .......................................................................................................... 6-3 Call service messages ............................................................................................................ 6-3 Troubleshooting paper handling ................................................................................................... 6-4 Paper jams and how to clear them ............................................................................................... 6-5 JAM MP TRAY (paper jam in the multi-purpose tray) ............................................................ 6-6 JAM TRAY 1 / TRAY 2 (Paper jam inside the Paper tray) ..................................................... 6-7 JAM INSIDE (paper jam inside the printer) ............................................................................ 6-9 JAM REAR (paper jam behind the back output tray) ............................................................ 6-12 JAM DUPLEX (paper jam in the duplex unit) ....................................................................... 6-15 Improving the print quality .......................................................................................................... 6-17 Solving print problems ................................................................................................................ 6-22 Other problems ........................................................................................................................... 6-23 Printing from DOS ............................................................................................................... 6-23 BR-Script 3 ........................................................................................................................... 6-23 Appendix (Specifications, fonts and bar code) ....................................................................................A-1 Printer specifications ....................................................................................................................A-1 Engine ....................................................................................................................................A-1 Controller ................................................................................................................................A-2 Software .................................................................................................................................A-2 Control panel ..........................................................................................................................A-2 Paper handling .......................................................................................................................A-3 Media specifications ...............................................................................................................A-3 Supplies ..................................................................................................................................A-3 Dimensions / Weights .............................................................................................................A-4 General ...................................................................................................................................A-4 System requirements ..............................................................................................................A-4 Important information for choosing your paper .............................................................................A-5 Quick reference for bar code control commands ..........................................................................A-7 Print bar codes or expanded characters .................................................................................A-7 Appendix (For Europe and Other Countries) .......................................................................................B-1 Brother Numbers ..........................................................................................................................B-1 Important information: Regulations ...............................................................................................B-2 Radio interference (220 to 240 volt model only) .....................................................................B-2 International ENERGY STAR® Compliance Statement ..........................................................B-2 IEC 60825 specification (220 to 240 volt model only) ............................................................B-3 6 7 8 vi Internal laser radiation ............................................................................................................B-3 IMPORTANT - For Your Safety ....................................................................................................B-4 Disconnect device ..............................................................................................................B-4 Caution for LAN connection (For model HL-6050DN only) ................................................B-4 IT power system (For Norway only) ...................................................................................B-4 Geräuschemission / Acoustic noise emission (for Germany only) .....................................B-4 Wiring information (for UK) .................................................................................................B-4 9 Appendix (For USA and Canada) ..........................................................................................................C-1 Brother Numbers ..........................................................................................................................C-1 Important information: Regulations ...............................................................................................C-3 Federal Communications Commission (FCC) Declaration of Conformity (For USA) .............C-3 Industry Canada Compliance Statement (For Canada) .........................................................C-4 International ENERGY STAR® Compliance Statement ..........................................................C-4 Laser Notice .................................................................................................................................C-5 Laser Safety (100 to 120 volt model only) ..............................................................................C-5 FDA Regulations (100 to 120 volt model only) .......................................................................C-5 Internal laser radiation ............................................................................................................C-5 IMPORTANT - For Your Safety ....................................................................................................C-6 Disconnect device ..............................................................................................................C-6 Caution for LAN connection (For model HL-6050DN only) ................................................C-6 Index ......................................................................................................................................................... I-1 10 vii 1 About this printer What is in the box? When you unpack the printer, check to see that you have all of the following parts. 1 1 2 3 4 5 2 Printer Drum unit assembly (with toner cartridge included) Quick setup guide CD-ROM AC power cord Components may differ from one country to another. 3 4 5 Figure 1-1 The power cord may be slightly different than the one shown in the Figure 1-1, depending on which country the printer was bought in. Interface cable An interface cable is not a standard accessory. Some computers have a USB and a parallel port. Please buy the appropriate cable for the interface you intend to use. Most parallel cables support bi-directional communication, but some might have an incompatible pin assignment or may not be IEEE 1284-compliant. It is recommended to use a parallel interface cable or USB interface cable that is no longer than 2 meters (6 feet). When you use a USB cable, make sure that you connect it to the USB connector of your PC. Please make sure that you use a Hi-Speed USB 2.0 certified cable if your computer uses a Hi-Speed USB 2.0 interface. Do not connect the USB cable to a non-powered hub or a Macintosh® keyboard. 1 - 1 ABOUT THIS PRINTER Front view Front view 1 2 3 4 8 7 6 5 Figure 1-2 1 2 3 4 5 6 7 8 Face down output tray support flap (support flap) Control panel Multi-purpose tray (MP tray) MP tray support flap Paper tray Front cover release button Front cover Face down output tray (top output tray) ABOUT THIS PRINTER 1 - 2 Back view Back view* 11 10 9 1 2 8 7 6 5 4 Figure 1-3 Face up output tray (back output tray) Face up output tray support AC power connector Power switch Parallel interface connector USB interface connector Side cover (HL-6050DN) 10/100BASE-TX port (HL-6050DN) network LED (light-emitting diode) (HL-6050DN) network test button CompactFlash® card slot * The printer illustration is based on HL-6050DN. 3 1 2 3 4 5 6 7 8 9 10 11 1 - 3 ABOUT THIS PRINTER Positioning the printer Please read the following before you use the printer. Power supply Use the printer within the recommended power range. Power source: USA and Canada: AC 100 to 120 V, 50/60 Hz Europe and Australia: AC 220 to 240 V, 50/60 Hz The power cord, including extensions, should be no longer than 5 meters (16½ feet). Do not share the same power circuit with other high-power appliances, such as an air conditioner, copier, shredder and so on. If you cannot avoid using the printer with these appliances, we recommend that you use a voltage transformer or a high-frequency noise filter. Use a voltage regulator if the power source is not stable. Environment Make sure that the power outlet/socket is near the printer and is easy to get to so that, if there is an emergency, it can be easily unplugged. Only use the printer within the following ranges of temperature and humidity: Temperature: 10 °C to 32.5 °C (50 °F to 90.5 °F) Humidity: 20% to 80% (without condensation) The printer should be used in a well-ventilated room. Put the printer on a flat, horizontal surface. Keep the printer clean. Do not put the printer in a dusty place. Do not put the printer where the ventilation hole of the printer is blocked. Keep a gap of approximately 100 mm (4 in.) between the ventilation hole and the wall. Do not put the printer in direct sunlight. If you have to put it near a window, use a blind or a heavy curtain to protect the printer from direct sunlight. Do not put the printer near devices that contain magnets or generate magnetic fields. Do not subject the printer to strong physical shocks or vibrations. Do not expose the printer to open/naked flames or salty or corrosive gasses. Do not put objects on top of the printer. Do not put the printer near an air conditioner. Keep the printer horizontal when you carry it. ABOUT THIS PRINTER 1 - 4 What kind of paper can I use? Type and size of paper The printer loads paper from the installed paper tray, manual feed tray (multi-purpose tray) or optional lower tray unit. The names for the paper trays in the printer driver and this guide are as follows: Paper tray Multi-purpose tray Optional lower tray unit Tray 1 MP tray Tray 2 While looking at this page on the CD-ROM, you can jump to the page for each printing method by clicking in the table. Media type Paper weight Tray 1 MP tray Tray 2 Automatic duplex printing Select the Media type from the printer driver Plain paper Plain paper 75 g/m2 to 105 g/m2 (20 to 28 lb) Recycled paper Bond paper Rough paper 60 g/m2 to 161 g/m2 (16 to 43 lb) 60 g/m2 to 105 g/m2 (16 to 28 lb) 60 g/m2 to 161 g/m2 (16 to 43 lb) 60 g/m2 to 105 g/m2 (16 to 28 lb) Recycled paper Bond paper Thick paper 105 g/m2 to 161 g/m2 (28 to 43 lb) Thick paper or Thicker paper Transparency Up to 10 sheets A4 or Letter Up to 10 sheets A4 or Letter Up to 10 sheets A4 or Letter Transparencies Thicker paper A4 or Letter Labels Envelopes Card stock Thin paper 60 g/m2 to 75 g/m2 (16 to 20 lb) Envelopes Envelopes - Thin Thick paper or Thicker paper Thin paper When you print on thick paper, labels or card stock, we recommend that you select the media type setting in the printer driver according to the paper weight. 1 - 5 ABOUT THIS PRINTER Tray 1 Paper size A4, Letter, Legal, B5 (ISO), A5, B6 (ISO), A6, Executive, Folio MP tray Width: 69.9 to 215.9 mm (2.75 to 8.5 in.) Length: 116 to 406.4 mm (4.57 to 16 in.) 100 sheets (80 g/m2 or 20 lb) Tray 2 A4, Letter, Legal, B5 (ISO), A5, B6 (ISO), A6, Executive, Folio Automatic duplex printing A4, Letter, Legal Number of sheets 500 sheets (80 g/m2 or 20 lb) 500 sheets (80 g/m2 or 20 lb) You must use the face up output tray (back output tray) for certain print media. When looking at this page on the CD-ROM, you can jump to the page for each printing method by clicking the in the table. Media type Plain paper Recycled paper Bond paper Thick paper Thcker paper Transparency Labels Envelope Card stock Thin paper Face down Face up You can use the control panel Menu buttons to select the priority of the paper source in the PAPER menu. See PAPER on page 3-15. We recommend that you use face up printing when you print on transparencies. ABOUT THIS PRINTER 1 - 6 Recommended paper Europe Plain paper Recycled paper Transparency Labels Xerox Premier 80 3M CG3300 Avery laser label L7163 g/m2 g/m2 3M CG 3300 Avery laser label #5160 Xerox Recycled Supreme 80 USA Xerox 4200DP 20 lb Before you buy a lot of paper, please test some to make sure that the paper is suitable. Use paper that is made for plain-paper copying. Use paper that is 75 to 90 g/m2 (20 to 24 lb). Use neutral paper. Do not use acidic or alkaline paper. Use long-grain paper. Use paper with a moisture content of approximately 5%. This printer can use recycled paper that meets the DIN 19309 specification. Caution Do not use ink jet paper, it may cause a paper jam and damage your printer. To help you choose which paper to use with this printer, see Important information for choosing your paper on page A-5. When you print on smaller sized short-grain paper (A5, A6 and Executive), do the following: Go to the Basic tab of the printer driver, in the Media Type option select Envelopes. And then, at the back of the printer, open the back output tray and push down the two blue tabs one on the left and one on the right hand side (as shown in Figure 1-4). When you have finished printing, close the back output tray to reset the two blue tabs back to their original position. Figure 1-4 1 - 7 ABOUT THIS PRINTER Printable area When using PCL (standard driver) emulation, the edges of the paper that cannot be printed on are shown below. Portrait 1 2 3 Figure 1-5 A4 Letter 4.2 mm (0.17 in.) 6.35 mm (0.25 in.) 4.2 mm (0.17 in.) 6.35 mm (0.25 in.) Legal 4.2 mm (0.17 in.) 6.35 mm (0.25 in.) 4.2 mm (0.17 in.) 6.35 mm (0.25 in.) B5 (ISO) 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) 4 Executive 4.2 mm (0.17 in.) 6.35 mm (0.25 in.) 4.2 mm (0.17 in.) 6.35 mm (0.25 in.) A5 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) A6 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) B6 (ISO) 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) 1 2 3 4 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) 4.2 mm (0.17 in.) 6.01 mm (0.24 in.) When using BR-Script emulation, the edges of the paper that cannot be printed on are 4.32 mm (0.17 in.). ABOUT THIS PRINTER 1 - 8 Landscape 1 2 3 Figure 1-6 A4 Letter 4.2 mm (0.17 in.) 5.08 mm (0.2 in.) 4.2 mm (0.17 in.) 5.08 mm (0.2 in.) Legal 4.2 mm (0.17 in.) 5.08 mm (0.2 in.) 4.2 mm (0.17 in.) 5.08 mm (0.2 in.) B5 (ISO) 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) Executive 4.2 mm (0.17 in.) 5.08 mm (0.2 in.) 4.2 mm (0.17 in.) 5.08 mm (0.2 in.) 4 A5 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) A6 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) B6 (ISO) 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) 1 2 3 4 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) 4.2 mm (0.17 in.) 5.0 mm (0.19 in.) When using BR-Script emulation, the edges of the paper that cannot be printed on are 4.32 mm (0.17 in.). 1 - 9 ABOUT THIS PRINTER Printing methods Printing on plain paper You can print on plain paper from the paper tray or multi-purpose tray. For the paper you want to use, please see What kind of paper can I use? on page 1-5. Printing on plain paper from the paper tray 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Plain Paper Paper Source: Tray 1 (or Tray 2) PCL (standard) printer driver BR-Script printer driver ABOUT THIS PRINTER 1 - 10 2 Pull the paper tray completely out of the printer. Figure 1-7 3 While pressing the blue paper-guide release lever, slide the paper guides to fit the paper size. Check that the guides are firmly in the slots. Figure 1-8 4 To avoid paper jams and misfeeds, fill up the paper tray with small stacks of paper that you have fanned well. Put the side that is going to be printed on first (blank side), face down, with the leading edge (top) of the paper in last (at the front of the tray). Check that the paper is flat in the paper tray at all four corners. Figure 1-9 1 - 11 ABOUT THIS PRINTER Do not put more than 500 sheets of paper (80 g/m2) in the paper tray at any one time, or it may cause a jam. Check that paper is below the maximum paper height guide (). Figure 1-10 5 Put the paper tray firmly back in the printer. Check that it is inserted fully into the printer. Figure 1-11 6 Send the print data to the printer. Figure 1-12 ABOUT THIS PRINTER 1 - 12 Printing on plain paper from the multi-purpose tray (MP tray) The printer automatically turns on the MP Tray mode when you put paper in the multi-purpose tray. 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Plain Paper Paper Source: MP Tray PCL (standard) printer driver BR-Script printer driver 1 - 13 ABOUT THIS PRINTER 2 Open the MP tray and lower it gently. Figure 1-13 3 Pull out the MP tray support flap. Figure 1-14 4 Put paper in the MP tray. Put the side to be printed on first, face up, with the leading edge (top) of the paper in first. Make sure the paper touches the back of the tray and remains under the maximum paper height guides on both sides of the tray. Do not put more than 100 sheets of paper (80 g/m2 or 20 lb) in the MP tray at any one time, or it may cause a jam. Figure 1-15 ABOUT THIS PRINTER 1 - 14 Make sure that the paper is straight and in the proper position on the MP tray. If it is not, the paper may not be fed properly, resulting in a skewed printout or a paper jam. 5 While pressing the paper-guide release lever, slide the paper guide to fit the paper size. Figure 1-16 When you put paper in the MP tray, please remember the following: The side to be printed on must be face up. During printing, the inside tray rises to feed paper into the printer. Put the leading edge (top of the paper) in first and push it gently into the tray. The top of the paper stack must be under the maximum paper height guides that are on both sides of the tray. 6 Send the print data to the printer. Figure 1-17 1 - 15 ABOUT THIS PRINTER Printing on thick paper, labels and card stock Do not use damaged, curled, wrinkled, or irregularly shaped paper. Do not use labels without a mount. We recommend that you use paper that is made for laser printers. Use paper that can withstand intense heat; the interior of the printer reaches very high temperatures while printing. Figure 1-18 Before you print paper with holes, such as organizer sheets, you must fan the stack to avoid paper jams and misfeeds. Figure 1-19 Do not place the punched holes of organizer sheets near the actuator (paper sensor). Do not use organizer sheets that are stuck together. The glue on them might cause damage to the printer. Do not put different types of paper in the paper tray at the same time because it may cause paper jams or misfeeds. Do not print thick paper, labels or card stock using duplex printing. For proper printing, you must choose the same paper size from your software application as the paper in the tray. See What kind of paper can I use? on page 1-5. ABOUT THIS PRINTER 1 - 16 Printing on thick paper, labels or card stock from the multi-purpose tray (MP tray) When the back output tray is pulled down, the printer has a straight paper path from the MP tray through to the back of the printer. Use this paper feed and output method when you want to print on thick paper, labels or card stock. The printer automatically turns on the MP tray mode when you put paper in the MP tray. When you select the paper you want to use, see What kind of paper can I use? on page 1-5. 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Thick Paper or Thicker Paper Paper Source: MP Tray PCL (standard) printer driver BR-Script printer driver 1 - 17 ABOUT THIS PRINTER 2 Open the back output tray, and then pull out the face up output tray support if necessary. Figure 1-20 3 Open the MP tray and lower it gently. Figure 1-21 4 Pull out the MP tray support flap. Figure 1-22 ABOUT THIS PRINTER 1 - 18 5 Put paper in the MP tray. Put the side to be printed on first, face up, with the leading edge (top) of the paper in first. Make sure the paper touches the back of the tray and remains under the maximum paper height guides on both sides of the tray. Figure 1-23 Make sure that the paper is straight and in the proper position in the MP tray. If it is not, the paper may not be fed properly, resulting in a skewed printout or a paper jam. 6 While pressing the paper-guide release lever, slide the paper guide to fit the paper size. Figure 1-24 When you put paper in the MP tray, please remember the following: During printing, the inside tray rises to feed paper into the printer. The side to be printed on must be face up. Put the leading edge (top of the paper) in first and push it gently into the tray. The top of the paper stack must be under the maximum paper height guides that are on both sides of the tray. 7 8 Send the print data to the printer. After you finish the print job, close the back output tray. 1 - 19 ABOUT THIS PRINTER Caution Remove each sheet immediately after printing. Stacking the sheets may cause a paper jam or the paper to curl. Figure 1-25 ABOUT THIS PRINTER 1 - 20 Printing on envelopes Types of envelopes to avoid Do not use envelopes which: are damaged, curled, wrinkled, or an usual shape are extremely shiny or textured have clasps, snaps or tie strings have self-adhesive components are of a baggy construction are not sharply creased are embossed (have raised writing on them) have been previously printed on by a laser printer are pre-printed on the inside cannot be arranged when put in a pile are made of paper that weighs more than the paper weight specifications for the printer have been badly made, with edges that are not straight or consistently square have windows, holes, cutouts or perforations Figure 1-26 IF YOU USE ANY OF THE TYPES OF ENVELOPES LISTED ABOVE, THEY MAY DAMAGE YOUR PRINTER. THIS DAMAGE IS NOT COVERED UNDER ANY BROTHER WARRANTY OR SERVICE AGREEMENT. Before you print envelopes, you must fan the stack to avoid paper jams and misfeeds. Figure 1-27 Do not put different types of paper in the paper tray at the same time because it may cause paper jams or misfeeds. Do not print envelopes using duplex printing. For proper printing, you must choose the same paper size from your software application as the paper in the tray. See What kind of paper can I use? on page 1-5. 1 - 21 ABOUT THIS PRINTER Most envelopes will be suitable for your printer. However, some envelopes will have feed and print quality problems due to the way they have been made. A suitable envelope should have edges with straight, well-creased folds and the leading edge should not be thicker than two pieces of paper. The envelope should lie flat and not be of baggy or flimsy construction. You should buy quality envelopes from a supplier who understands that you will be using the envelopes in a laser printer. Before you print many envelopes, test one to make sure that the print results are what you want. Brother will not recommend a particular envelope because envelope manufacturers may change the envelope specifications. You are responsible for the quality and performance of the envelopes you use. ABOUT THIS PRINTER 1 - 22 Printing on envelopes from the MP tray When the back output tray is pulled down, the printer has a straight paper path from the MP tray through to the back of the printer. Use this paper feed and output method when you want to print envelopes. The printer automatically turns on the MP Tray mode when you put paper in the MP tray. 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Envelopes Paper Source: MP Tray PCL (standard) printer driver BR-Script printer driver 1 - 23 ABOUT THIS PRINTER 2 Open the back output tray, and then pull out the face up output tray support if necessary. Figure 1-28 3 Open the MP tray and lower it gently. Figure 1-29 4 Pull out the MP tray support flap. Figure 1-30 ABOUT THIS PRINTER 1 - 24 Envelopes that have been creased after they have been printed At the back of the printer, open the back output tray and push down the two blue tabs one on the left and one on the right hand side (as shown in Figure 1-31). When you have finished printing your envelopes, close the back output tray to reset the two blue tabs back to their original position. Figure 1-31 5 Put envelopes in the MP tray so that they touch the back of the tray and remain under the maximum paper height guides on both sides of the tray. Put the side to be printed on first, face up, with the leading edge (top) of the envelope in first. Do not put more than 3 envelopes in the MP tray at any one time, or it may cause a jam. Figure 1-32 Make sure that the envelopes are neatly stacked and in the proper position in the MP tray. If they are not, the envelopes may not be fed properly, resulting in a skewed printout or a jam. 1 - 25 ABOUT THIS PRINTER 6 Press and slide the paper width guide to fit the envelope size. Figure 1-33 DL size double-flap envelopes If the DL size double flap envelope is creased after printing, go to the Basic tab, select Paper Size and then select DL Long Edge. Put a new DL size double-flap envelope in the MP tray with the longest edge of the envelope in first, then print again. When you put envelopes in the MP tray, please remember the following; During printing, the inside tray rises to feed envelopes into the printer. The side to be printed on must be face up. Put the leading edge (top of the paper) in first and push it gently into the tray. The top of the envelope stack must be under the maximum paper height guides that are on both sides of the tray. 7 8 Send the print data to the printer. After you finish the print job, close the back output tray. ABOUT THIS PRINTER 1 - 26 If envelopes get smudged during printing, in the printer driver select MP Tray as the Paper Source for a straight paper path. Then, set the Media Type to Thick Paper or Thicker Paper to increase the fixing temperature. To adjust the print density setting, See QUALITY on page 3-15. Envelope joints that are sealed by the manufacturer should be secure. All sides should be properly folded without any wrinkles or creases. 1 - 27 ABOUT THIS PRINTER Printing on transparencies You can print on transparencies from the paper tray or MP tray. Do W not touch transparencies that have just been printed because they are very hot. Printing on transparencies from the paper tray Do not put more than 10 transparencies in the paper tray. 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Transparencies Paper Source: Tray 1 (or Tray 2) PCL (standard) printer driver BR-Script printer driver ABOUT THIS PRINTER 1 - 28 2 Pull the paper tray completely out of the printer. Figure 1-34 3 While pressing the blue paper guide release levers, slide the paper guides to fit the transparency size. Check that the guides are firmly in the slots. Figure 1-35 4 Put transparencies in the tray. Put the side that is going to be printed on face down, with the top of the paper at the front of the tray. Check that the transparencies are flat in the tray at all four corners. Figure 1-36 1 - 29 ABOUT THIS PRINTER Do not put more than 10 transparencies in the tray at any one time, or it may cause a jam. Check that transparencies are below the maximum paper mark (). Figure 1-37 5 Put the paper tray firmly back in the printer. Check that it is inserted fully into the printer. Figure 1-38 6 Send the print data to the printer. Figure 1-39 Caution Remove each transparency before the next page is output on the top output tray to prevent transparencies from sticking to each other. ABOUT THIS PRINTER 1 - 30 Printing on transparencies from the MP tray When the back output tray is pulled down, the printer has a straight paper path from the MP tray through to the back of the printer. The printer automatically turns on the MP Tray mode when you put paper in the MP tray. 1 Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver. Media Type: Transparencies Paper Source: MP Tray PCL (standard) printer driver BR-Script printer driver 1 - 31 ABOUT THIS PRINTER 2 Open the back output tray, and then pull out the face up output tray support if necessary. Figure 1-40 3 Open the MP tray and lower it gently. Figure 1-41 4 Pull out the MP tray support flap. Figure 1-42 ABOUT THIS PRINTER 1 - 32 5 Put transparencies in the MP tray. Put the side to be printed on first, face up, with the leading edge (top) of the paper in first. Make sure the transparencies touch the back of the tray and remain under the maximum paper height guides on both sides of the tray. Do not put more than 10 transparencies in the MP tray at any one time, or it may cause a jam. Figure 1-43 Make sure that the transparencies are straight and in the proper position in the MP tray. If they are not, the transparencies may not be fed properly, resulting in a skewed printout or a jam. 6 While pressing the paper guide release lever, slide the paper guide to fit the transparency size. Figure 1-44 When you put transparencies in the MP tray, please remember the following: The side to be printed on must be face up. Put the leading edge (top of the transparencies) in first and push it gently into the tray. The top of the transparency stack must be under the maximum paper height guides that are on both sides of the tray. 1 - 33 ABOUT THIS PRINTER 7 8 Send the print data to the printer. After you finish printing, close the back output tray. Caution Remove each transparency immediately after printing. Stacking the printed transparencies may cause a paper jam or the transparency to curl. ABOUT THIS PRINTER 1 - 34 Printing on both sides of the paper The supplied printer drivers for Windows® 95/98/Me, Windows NT® 4.0, Windows® 2000/XP, Mac OS® 8.6 to 9.2 and Mac OS® X 10.1/10.2 all enable duplex printing. For more information about how to choose the settings, see the Help text in the printer driver. The BR-Script 3 printer driver (PostScript® 3TM Emulation) does not support manual duplex printing. Manual duplex printing from the paper tray (For PCL printer driver) 1 2 3 Choose the Manual Duplex printing mode from the Advanced tab, and from the Basic tab select the Paper Source to be Tray 1. The printer will automatically print all the even-numbered pages on one side of the paper first. Remove the printed even numbered pages from the output tray and put them back in the paper tray, placing the paper with the side to be printed on (blank side) face down. Follow the instructions on the computer screen. Figure 1-45 If you select the Paper Source to be Auto Select in Step 1, please put the printed even-numbered pages in the MP tray. 4 The printer will now automatically print all the odd numbered pages on the other side of the paper. 1 - 35 ABOUT THIS PRINTER Manual duplex printing from the multi-purpose tray Caution Before putting the sheets back in the MP tray, you will have to straighten them, or you may get paper jams. You should not use very thin or very thick paper. When you use the manual duplex function, it is possible that there may be paper jams or poor print quality. If there is a paper jam, see Paper jams and how to clear them on page 6-5. 1 2 Open the Properties dialog box in the printer driver. Choose the General tab and click the Printing Preferences icon. Choose the Manual Duplex printing mode from the Advanced tab, and from the Basic tab select the Paper Source to be MP Tray. Put the paper in the MP tray with the side to be printed on first facing up. Follow the instructions on the computer screen. Repeat this step until you have printed all the even numbered pages. Figure 1-46 3 Remove the printed even-numbered pages from the output tray and put them in the same order back into the MP tray. Place the paper with the side which will be printed on (the blank side) face up. Follow the instructions on the computer screen. Figure 1-47 4 Repeat Step 3 until you have printed all the odd numbered pages on the other side of the paper. ABOUT THIS PRINTER 1 - 36 Automatic duplex printing (available for HL-6050D and HL-6050DN only) The screens in this section are from Windows® XP. The screens on your PC will vary depending on your operating system. Caution Use A4, Letter or Legal size paper when you use automatic duplex printing function. Ensure that the back output tray is closed Ensure that the duplex tray is installed correctly in the printer. Figure 1-48 1 2 Put paper in the paper tray or MP tray. Set the paper adjustment lever for duplex printing at the back of the printer to match your paper size. Letter or Legal size A4 size Figure 1-49 If the paper adjustment lever for duplex printing is not correctly set for the paper size, paper jams may occur and the print will be out of position on the paper. 1 - 37 ABOUT THIS PRINTER 3 For the PCL (standard) printer driver Open the Properties dialog box in the printer driver. Choose the General tab and click the Printing Preferences icon. Choose the Duplex mode in the Advanced tab, make sure that Use Duplex Unit has been selected, and then click the OK button. The printer will print on both sides of the paper automatically. For the BR-Script printer driver Open the Properties dialog box in the printer driver. Choose the General tab and click the Printing Preferences icon. In the Layout tab, select Orientation, Print on Both Sides (Duplex) and Page Order, and then click the OK button. The printer will print on both sides of the paper automatically. ABOUT THIS PRINTER 1 - 38 Booklet printing (for the PCL printer driver) (available for HL-6050D and HL-6050DN only) 1 2 Put paper in the paper tray or MP tray. When you use A4 size or Letter size paper, set the paper adjustment lever for duplex printing to match your paper size. Letter or Legal size A4 size Figure 1-50 If the paper adjustment lever for duplex printing is not correctly set for the paper size you are using, paper jams may occur and the print will be out of position on the paper. 3 Open the Properties dialog box in the printer driver. Choose the General tab and click the Printing Preferences icon. After you click the Duplex icon in the Advanced tab, check the Booklet Printing setting. Select the Duplex mode. The printer will print a Booklet automatically. 1 - 39 ABOUT THIS PRINTER Guidelines for printing on both sides of the paper If the paper is thin, it may wrinkle. If paper is curled, straighten it and then put it back in the paper tray. You should use regular paper. Do not use bond paper. If the paper is not feeding properly, it may be curled. Remove the paper and straighten it. (For manual duplex printing) When you put paper in the paper tray, first empty the tray of any other paper then put the printed page in to the empty tray, with the printed side face up. (Do not add printed pages to the top of a stack of unprinted paper.) (For manual duplex printing ) For thick paper that has curled once the first side has been printed on, you cannot feed the paper for the second time from the MP tray to allow the other side of the paper to be printed. At the back of the printer, open the back output tray and push down the two blue tabs one on the left and one on the right hand side (as shown in Figure 1-51). When you have finished printing, close the back output tray to reset the two blue tabs back to their original position. Figure 1-51 ABOUT THIS PRINTER 1 - 40 Paper orientation for printing on both sides of the paper (for automatic duplex printing) The printer prints the second page first. If you print 10 pages on 5 sheets of paper, it will print page 2 then page 1 on the first sheet of paper. It will print page 4 then page 3 on the second sheet of paper. It will print page 6 then page 5 on the third sheet of paper, and so on. When doing automatic duplex printing, the paper must be put in the paper tray in the following way: For the paper tray: Put the side to be printed on first, face down, with the leading edge (top) of the paper at the front of the tray. To print the second side, put the paper face up, with the leading edge (top) of the paper at the front of the tray. If letterhead paper is used, this would be put in the paper tray with the heading face up, and at the front of the tray. To print the second page, put the heading face down and at the front of the tray. For the MP tray: Put the side to be printed on first, in face up, with the leading edge (top) of the paper in first. To print the second side, put the paper face down, with the leading edge (top) of the paper in first. If letterhead paper is used, this would be put in with the heading face down, and in first. To print the second side, put the heading face up and in first. 1 - 41 ABOUT THIS PRINTER Carbon copy printing Carbon copy printing enables you to automatically print one page data to different styles of paper by changing the paper source. You can make copies as though you are printing on carbon paper using a dot matrix printer. For example, you can print `Data A' to `Sheet 1' which is blue colored paper and then to `Sheet 2' which is yellow colored and has some information already printed. If you put paper for `Sheet 1' in the Tray 1 and paper for `Sheet 2' in the MP tray, the printer will automatically feed paper for `Sheet 1' from the Tray 1 and `Sheet 2' from the MP tray. For more information, visit http://solutions.brother.com/carboncopy ABOUT THIS PRINTER 1 - 42