User manual BROWNING GOLD AUTOLOADING 12 AND 20 GAUGE SHOTGUN

THE BEST THERE IS GOLD AUTOLOADING 12 & 20 GA SHOTGUN OWNER'S MANUAL THANK YOU FOR CHOOSING A BROWNING GOLD AUTOLOADING SHOTGUN. The Gold shotgun represents a new generation of Browning gas-operated, autoloading shotguns. The Gold 12 and 20 gauge incorporate the best of traditional Browning craftsmanship and advanced technology. Every detail of the Gold shotgun has been engineered to provide you the best in handling and reliable operation. With a reasonable amount of care your Gold shotgun should give you many years of dependable, enjoyable service. Please feel free to write us immediately if you have any observations regarding its performance and operation. SERVICE OR REPAIR If your firearm should require service or repairs, we suggest you first contact a local recommended Browning Firearms Service Center. Contact your Browning sporting goods dealer or call our Service Department for the address of the Service Center nearest you. Otherwise, you may send your firearm directly to our own Service Department. For technical questions about your firearm or service, contact: Browning Service Department One Browning Place Arnold, Missouri 63010-9406 Phone 1-800-322-4626 Canadian Customers call or write: Browning Canada Sports Ltd./Ltee, 5617 Chemin St-François St-Laurent, Quebec H4S 1W6 Phone: (514) 333-7261 When returning your firearm for servicing, you must do the following: 1. Be sure it is completely unloaded. 2. Package it securely in a cardboard container. 3. Enclose a letter with your firearm that clearly describes the trouble experienced and the repairs desired. 4. If convenient, send a copy of the letter to us separately. 5. Never return ammunition with your firearm. It is against postal and most commerce regulations. If you have any questions about this manual or about any other Browning products, call or write our Consumer Information Department: Browning Consumer Information One Browning Place Morgan Utah 84050 Phone: (801) 876-2711 YOU ARE RESPONSIBLE FOR FIREARMS SAFETY As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities can be the difference between life and death. Failure to follow any of these instructions can cause extensive damage to your gun and/or possible serious injury or death to yourself or others. THERE IS NO EXCUSE FOR CARELESS OR ABUSIVE HANDLING OF ANY FIREARM. AT ALL TIMES, HANDLE ANY FIREARM WITH INTENSE RESPECT FOR ITS POWER AND POTENTIAL DANGER. PLEASE READ AND UNDERSTAND ALL OF THE CAUTIONS, PROPER HANDLING PROCEDURES AND INSTRUCTIONS OUTLINED IN THIS BOOKLET BEFORE USING YOUR NEW FIREARM. 1 ALWAYS KEEP THE MUZZLE OF YOUR SHOTGUN POINTED IN A SAFE DIRECTION. Do this even though you are certain it is unloaded. Never point any firearm at anything you do not intend to shoot. Be extremely alert and aware of all persons and property within the range of your ammunition. 2 NEVER RELY TOTALLY ON YOUR SHOTGUN'S MECHANICAL "SAFETY" DEVICE. Always assume that your gun can be fired at any time, even with all safety mechanisms engaged. The word "safety" describes a gun's mechanical devices that are designed to place your gun in a SAFER status. No guarantee can be made that the gun will not fire even if the "safety" is in the "on safe" position. See "Operation of the Safety" later in this manual for instructions on operation of this gun's "safety." LIKE ANY MECHANICAL DEVICE, A "SAFETY" CAN SOMETIMES FAIL; IT CAN BE JARRED OR INADVERTENTLY MANIPULATED INTO AN UNSAFE CONDITION. Mechanical "safeties" merely aid safe gun handling and are no excuse for pointing your shotgun's muzzle in an unsafe direction. While it is a good idea to "test" your gun's mechanical "safeties" periodically for proper function, NEVER TEST THEM WHILE YOUR FIREARM IS LOADED OR POINTED IN AN UNSAFE DIRECTION. Safe gun handling does not stop with your gun's mechanical "safety" 2 devices, -- it starts there. Always treat this shotgun with the respect due a loaded, ready-to-fire firearm. NEVER TEST THE MECHANISM OF ANY FIREARM WHILE IT IS LOADED OR POINTED IN AN UNSAFE DIRECTION. 3 WHENEVER YOU HANDLE ANY FIREARM, OR HAND IT TO SOMEONE, MAKE SURE IT IS COMPLETELY UNLOADED. Always open the action immediately, and visually check the chamber. Make certain that the chamber does not inadvertently contain any ammunition. Always keep the chamber empty and the safety in the "on safe" position unless shooting is imminent. 4 DO NOT TRANSPORT ANY LOADED FIREARM. Keep all firearms unloaded during transport, whether stored in a holster, gun case, scabbard or other container. 5 HUNTING FROM ELEVATED SURFACES SUCH AS TREESTANDS IS DANGEROUS. Doing so may increase the risk of mishandling a firearm. The following rules should always be observed by you and those you hunt with: Always make certain that the stand being used is safe and stable. Always make certain that your firearm is unloaded when it is being taken up and down from the stand. Always make certain that your firearm is not dropped from the stand or dropped while it is being taken up or down from the stand. Remember, a loaded firearm may discharge when dropped, even with the safety in the "on safe" position. 6 BEWARE OF BARREL OBSTRUCTIONS. Do this for the safety of both your gun and yourself. Mud, snow and an infinite variety of other objects may inadvertently lodge in a barrel bore. It takes only one small obstruction to cause dangerously increased pressures that can ruin (swell or rupture) the finest barrels. BEFORE CHECKING FOR A BARREL OBSTRUCTION, BE CERTAIN YOUR FIREARM IS COMPLETELY UNLOADED. Make sure no live rounds are in the chamber(s). Place the safety in the "on safe" position. After assuring yourself that the firearm is completely unloaded, again, open the breech or action and look through the barrel(s) to be sure it is clear of any obstruction. If an obstruction is seen, no matter 3 how small it may be, clean the bore with a cleaning rod and patch as described later in this manual. Before the first firing, clean the bore with a cleaning rod and patch, and wipe away any anti-rust compounds in the action/chamber areas. 7 ALWAYS COMPLETELY UNLOAD ALL FIREARMS WHEN NOT IN USE. As a safety precaution, it is preferable to disassemble your gun for storage. Your responsibilities do not end when your firearm is unattended. Store your firearm and ammunition separately and well beyond the reach of children. Take all safeguards to ensure that any firearm does not become available to untrained, inexperienced or unwelcome hands. 8 USE THE PROPER AMMUNITION. The barrel and action of all Browning firearms have been made with substantial safety margins over the pressures developed by established American commercial loads. Nevertheless, Browning assumes no liability for incidents which occur through the use of cartridges of nonstandard dimensions which develop pressures in excess of commercially available ammunition which has been loaded in accordance with standards established by the Sporting Arms and Ammunition Manufacturers' Institute (SAAMI). 9 BE ALERT TO THE SIGNS OF AMMUNITION MALFUNCTION. IF YOU DETECT AN OFF SOUND OR LIGHT RECOIL WHEN A SHELL IS FIRED, DO NOT LOAD ANOTHER SHELL INTO THE CHAMBER. Open the action and remove the shell from the chamber(s) as well as the action areas and magazine (when applicable). With the action open, glance down the barrel to make sure that a wad or other obstruction does not remain in the barrel. Completely clear the barrel before loading and firing again. Failure to follow these instructions can cause extensive damage to your gun and possible serious injury to yourself and others. 10 MAKE SURE OF ADEQUATE VENTILATION IN THE AREA THAT YOU DISCHARGE A FIREARM. WASH HANDS THOROUGHLY AFTER EXPOSURE TO AMMUNITION OR AFTER CLEANING A FIREARM. Lead exposure can be obtained from discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition. Lead is a substance that has been known to cause birth defects, reproductive harm and other serious injury. 4 11 NEVER INSERT A SHELL OF THE INCORRECT GAUGE IN ANY SHOTGUN. The gauge of your shotgun is marked on the side of the barrel. Store all shells of different gauges in completely separate and well-marked containers. Never store shells of mixed gauges in a common container or in your pockets. EXAMINE EVERY SHELL YOU PUT IN YOUR GUN. NEVER PUT A 20 GAUGE SHELL IN A 12 GAUGE GUN. The most common way to bulge or rupture a shotgun barrel is to drop a 20 gauge shell into a 12 gauge chamber. The 20 gauge shell, unfortunately, will not fall completely through the barrel; its rim is caught by the front of a 12 gauge chamber. Your gun will misfire (with the chamber appearing to be empty). It is then possible to load a 12 gauge shell behind the 20 gauge shell. If the gun is then fired, the result will be a so-called "12-20 burst" which can cause extensive damage to your gun and possible serious injury to you and others. 12 USE SHELLS OF THE CORRECT LENGTH. Do not use 3 1/2" shotgun shells in any shotgun or barrel with a 2 3/4" or 3" chamber. Do not use 3" shells in a shotgun chambered for 2 3/4" shells. Doing so can result in a buildup of dangerously high pressures that may damage your gun and possibly cause serious injury to yourself or others. The size of the chamber is inscribed, along with gauge and choke designations on the side of the barrel. 13 DO NOT SNAP THE FIRING PIN ON AN EMPTY CHAMBER --THE CHAMBER MAY NOT BE EMPTY! Treat every gun with the respect due a loaded gun, even though you are certain the gun is unloaded. 14 KEEP YOUR FINGERS AWAY FROM THE TRIGGER WHILE LOADING AND UNLOADING UNTIL YOU ARE READY TO SHOOT. 15 BE SURE OF YOUR TARGET AND BACKSTOP. Particularly during low light periods. Know the range of your ammunition. Never shoot at water or hard objects. 16 ALWAYS UNLOAD THE CHAMBER AND MAGAZINE OF ANY FIREARM BEFORE CROSSING A FENCE, CLIMBING A TREE, JUMPING A DITCH OR NEGOTIATING OTHER OBSTACLES. Never lean or place any loaded 5 firearm on or against a fence, tree, car or other similar object. 17 WEAR EYE AND EAR PROTECTION WHEN SHOOTING. Unprotected, repeated exposure to gunfire can cause hearing damage. Wear ear protectors (shooting ear plugs or muffs) to guard against such damage. Wear shooting glasses to protect your eyes from flying particles. Always keep a safe distance between the muzzle of your firearm and any persons nearby, as muzzle blast, debris and ejecting shells could inflict serious injury. Also, wear eye protection when disassembling and cleaning any firearm to prevent the possibility of springs, spring-tensioned parts, solvents or other agents from contacting your eyes. 18 DROPPING OR JARRING A LOADED GUN CAN CAUSE AN ACCIDENTAL DISCHARGE. This can occur even with the "safety" in the "on safe" position. Be extremely careful while hunting or during any shooting activity, to avoid dropping any firearm. 19 IF ANY FIREARM FAILS TO FIRE, KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. Hold this position for a minimum of 30 seconds. Carefully open the action and remove the shell or cartridge. If the primer is indented, the cartridge should be disposed of in a way that cannot cause harm. If the primer is not indented, your firearm should be examined by a qualified gunsmith and the cause of the malfunction should be corrected before further use. 20 BE DEFENSIVE AND ON GUARD AGAINST UNSAFE GUN HANDLING AROUND YOU AND OTHERS. Don't be timid when it comes to gun safety. If you observe other shooters violating any of these safety precautions, politely suggest safer handling practices. 21 BE CERTAIN ALL FIREARMS ARE UNLOADED BEFORE CLEANING. Because so many gun accidents occur when a firearm is being cleaned, special and extreme care should be taken to be sure your gun is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition. 22 TEACH AND SUPERVISE FIREARMS SAFETY TO ALL MEMBERS OF YOUR FAMILY -- ESPECIALLY TO CHILDREN AND NONSHOOTERS. 6 Closely supervise newcomers to the shooting sports. Encourage enrollment in hunting/shooting safety courses. 23 NEVER DRINK ALCOHOLIC BEVERAGES OR TAKE ANY TYPE OF DRUGS BEFORE OR DURING SHOOTING. Your vision and judgment could be dangerously impaired, making your gun handling unsafe to you and to others. 24 PERFORM PERIODIC MAINTENANCE -- AVOID UNAUTHORIZED SERVICING. Your new firearm is a mechanical device which will not last forever, and as such, is subject to wear and requires periodic inspection, adjustment and service. Browning firearms should be serviced by a Browning Recommended Service Center or by Browning's service facility in Arnold, Missouri. Browning cannot assume any responsibility for injuries suffered or caused by unauthorized servicing, alterations or modifications of Browning firearms. 25 BROWNING RESERVES THE RIGHT TO REFUSE SERVICE ON FIREARMS THAT HAVE BEEN ALTERED, ADDED TO OR SUBSTANTIALLY CHANGED. Removal of metal from barrel(s), or modifications of the firing mechanism and/or operating parts may lead to Browning's refusal of service on such firearms. Browning will charge the owner for parts and labor to return the firearm to original Browning specifications. 26 READ AND HEED ALL WARNINGS in this instruction book, on ammunition boxes and with all accessories that you install on your firearm. It is your responsibility to secure the most up-to-date information on the safe handling procedures of your Browning gun. Browning assumes no liability for incidents which occur when unsafe or improper gun accessories or ammunition combinations are used. DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER, SAFETY OR OTHER PARTS OF THE FIRING MECHANISM OF THIS OR ANY OTHER FIREARM. FAILURE TO OBEY THIS WARNING MAY RESULT IN INJURY OR DEATH TO YOURSELF OR OTHERS. BE CAREFUL! 7 FIGURE 1 Safety Operating Handle Rib Barrel Butt Stock Muzzle Receiver Trigger Forearm Magazine Cap Carrier Release Button N O M E N C L AT U R E In conventional gun terminology, the position and movement of shotgun parts are described as they occur with the shotgun horizontal and in normal firing position; i.e. the muzzle is forward or front; the butt stock is rearward or rear; the trigger is downward or underneath; the sight is upward or on top. For general parts nomenclature, refer to Figure 1. The Browning Gold shotgun is shown disassembled to the extent necessary in order to follow instructions contained in this book (Figure 1-A on the next page). G E N E R A L O P E R AT I O N The Browning Gold shotgun is a gas operated, autoloading shotgun. It is capable of shooting five shots (with the magazine plug removed using 2 3/4" loads) in rapid succession with each pull of the trigger. Upon firing, high pressure gas from behind the shot charge passes through two ports in the barrel, through the gas bracket and into the gas cylinder. High pressure gases force the gas piston rearward, applying pressure to the piston rod. As the piston rod moves rearward, it pushes the bolt assembly rearward, operating the action. As the bolt assembly moves rearward, it recocks the hammer and ejects the fired shell. After full rearward travel, the bolt assembly returns forward, picking up a new shell from the magazine and chambering it automatically. After the last shell has been fired, the bolt assembly locks to the rear, instead of returning forward. This facilitates speedy reloading. The short-stroke of the gas piston along with the snug, gas sealing fit of the piston rod limits the amount of 8 FIGURE 1-A Gas Bracket Barrel Extension Bolt Slide Link Bolt Bolt Slide Bolt Handle Magazine Tube Trigger Pins Sleeve Spring Trigger Group Gas Sleeve Gas Piston Magazine Cap Magazine Spring Magazine Follower Forearm Magazine Spring Retainer Three Shot Adapter combustion gases blown out of the gas cylinder and into the receiver, keeping the inside of the receiver clean. NOTE: THE GOLD SHOTGUN IS DELIVERED WITH THE MAGAZINE ADAPTER IN THE MAGAZINE WHICH LIMITS THE GUN TO THREE SHOTS, IN ACCORDANCE WITH FEDERAL MIGRATORY BIRD LAWS. IF YOU DO NOT WANT YOUR GUN TO BE LIMITED, MERELY TAKE OUT THE THREE SHOT ADAPTER AS EXPLAINED ON PAGE 16 UNDER "THREE SHOT ADAPTER." INITIAL CLEANING Various exposed metal parts of your new gun have been coated at the factory with a rust preventative compound. Before assembling your shotgun, clean the anti-rust compound from the inside of the barrel, receiver and the action-chamber areas. Browning Oil is ideal for removing this compound and for giving your new gun its first lubrication. However, any quality gun oil may be used. Clean the barrel using a cleaning rod and patch as explained under "Cleaning and Maintenance Suggestions" on page 25. 9 FIGURE 2 SERIAL NUMBER The serial number of your Gold shotgun is found on the left side of the receiver--just below the engraving "Gold Hunter." AMMUNITION The Gold Autoloading 12 and 20 gauge shotguns shoot all factory lead and steel 12 or 20 gauge 2 3/4" and 3" loads. Browning can assume no responsibility for incidents which occur through the use of cartridges of nonstandard dimension or those developing pressures in excess of SAAMI (Sporting Arms and Ammunition Manufacturer's Institute) established standards. "On Safe" FIGURE 2-A O P E R AT I O N O F T H E S A F E T Y The cross bolt safety prevents the trigger Ready to fire (Red band showing on left side) from being pulled when in the "on safe" position. The safety is located at the rear of the trigger guard (Figure 2). In the "off safe" position, a red warning band is visible on the safety button on the left side of the trigger guard. To place the gun "ON SAFE," press the safety button to the right. To move the safety to the FIRE position, press the safety to the left (Figure 2-A). The safety is reversible and can be reversed from right- to left-handed by a competent gunsmith. When installed, the left-handed safety will have the safety button's red warning band on the RIGHT side of the trigger guard. NOTE: DO NOT DEPEND ON THE RED COLOR ALONE TO INDICATE YOUR GUN'S SAFETY STATUS, AS TIME, EXPOSURE TO THE ELEMENTS, AND THE ABRASIVE ACTION OF CLEANING AGENTS CAN ERASE IT. 10 HOW TO ASSEMBLE THE BARREL TO THE RECEIVER The Gold shotgun is delivered in the box, with the barrel removed and the forearm still attached to the magazine tube. It is important to follow the exact sequence for assembly in steps 1 and 2, in order to properly assemble your Gold shotgun. Always place the safety in the "on safe" position before assembly procedures and check your gun carefully to be certain that the chamber, feed mechanism and magazine contain no shells. 1 Take the receiver in hand. First, lock the bolt rearward by pulling the operating handle fully to the rear. Remove the forearm from the magazine tube by unscrewing the magazine cap and sliding the forearm forward, off the magazine tube. Do not squeeze hard on the open rear end of the forearm. Too much pressure could cause the wood to split. 2 Components of the gas system -- the sleeve, sleeve spring and gas piston will remain in place and do not need to be removed, except for cleaning. If the components of the gas system have been removed, reinstall them as explained below. Otherwise, proceed to step 5. 3 Slide the sleeve onto the magazine tube with the piston rod end first. Check the piston rod to make sure it is aligned with the slot on the right side (ejection port side) of the receiver. Make sure the sleeve spring is properly positioned in the sleeve (Figure 3). 4 Slide the gas piston into the gas bracket (Figure 3-A). FIGURE 3 Align the piston rod with the slot in the receiver. 11 FIGURE 3-A FIGURE 3-B The gas piston fits into the gas bracket. Slide the gas assembly over the magazine tube and the barrel extension into the receiver. 5 With the gun in the vertical position, line the gas bracket and gas piston over the magazine tube (Figure 3-B). Slide the gas bracket and gas piston over the magazine tube. The barrel extension should slip solidly down into the receiver. Make sure the piston rod moves freely in its slot in the receiver. 6 Replace the forearm by sliding it onto the magazine tube and over the gas bracket so it seats securely. Install the magazine cap. Make sure the magazine cap is fully tightened down. Open and close the action several times and retighten the magazine cap. This will ensure a proper seal. D I S A S S E M B LY O F T H E B A R R E L F R O M T H E RECEIVER BEFORE STARTING DISASSEMBLY PROCEDURES, VISUALLY INSPECT THE CHAMBER, FEED MECHANISM AND MAGAZINE TO BE ABSOLUTELY CERTAIN THE SHOTGUN IS COMPLETELY UNLOADED. POINT THE BARREL IN A SAFE DIRECTION. 1 Unscrew the magazine cap and remove it. 2 Remove the forearm by sliding it forward off the magazine tube. 3 For cleaning, remove the barrel, piston and piston sleeve by sliding them forward off the magazine tube. See "Cleaning and Maintenance Suggestions" on page 25 and 26 for cleaning procedures. 12 If you are disassembling for storage, return the piston and piston sleeve onto the magazine tube as shown previously in Figure 3-B. Reinstall the forearm over the magazine tube and screw on the magazine cap. You will then have two compact units: the barrel, and the action with stock and forearm. CAUTION: AFTER THE BARREL HAS BEEN REMOVED FROM YOUR GUN, LEAVE THE BOLT IN THE OPEN POSITION. DO NOT PRESS THE CARRIER RELEASE BUTTON. If the bolt is released forward with the barrel removed, the cartridge stop will hit the front of the receiver and cause damage. D I S A S S E M B LY O F T H E T R I G G E R G R O U P A N D B O LT A S S E M B LY The trigger group or bolt can be removed if the action becomes excessively dirty or wet. If this occurs, disassemble the action for a complete cleaning as explained below. Your Gold shotgun is designed to allow full disassembly of the trigger group and bolt assembly in the field, without any tools. Detailed cleaning procedures are outlined under "Cleaning and Maintenance" on page 25. Full disassembly involves removal of the bolt assembly and the trigger group. Any disassembly beyond this should only be performed by a competent gunsmith. ALWAYS WEAR EYE PROTECTION WHEN PERFORMING ANY MAINTENANCE OR DISASSEMBLY. REMOVING THE TRIGGER GROUP 1 First, make certain the gun is totally unloaded and the "safety" is "on safe." CHECK THE MAGAZINE, FEED MECHANISM AND CHAMBER TO BE SURE THEY DO NOT CONTAIN ANY SHELLS. 2 While holding the bolt handle, release the bolt to its forward position by depressing the carrier release button. Again use caution when releasing the bolt assembly to its forward position. If you allow the bolt assembly to slam closed with the barrel removed, you could damage the receiver. 13 FIGURE 4 FIGURE 4-A Use a drive punch to push inward on the trigger guard pins. Push the trigger guard pins through the other side of the receiver. 3 Use a drive punch or similar FIGURE 4-B object to push inward on the trigger guard pins, using caution not to scratch the receiver (Figure 4). Trigger guard pins may be removed from either side of the receiver. Push the trigger guard pins clear through the opposite side of the receiver. Grasp the trigger guard and pull it up and out of It may be necessary to pull on the receiver. the trigger pins to remove them from the receiver (Figure 4-A). 4 Grasp the trigger guard and pull it up and out of the receiver (Figure 4-B). 5 Perform any cleaning of the parts and receiver cavity as necessary. DO NOT DISASSEMBLE THE TRIGGER GROUP BEYOND THIS POINT. 14 R E A S S E M B LY 1 Make sure the bolt is in the forward position. 2 Insert the trigger group back into the receiver. The holes in the trigger group should line up with the holes on each side of the receiver. 3 Reinsert the trigger guard pins and gently tap them into place with a plastic or wooden mallet, again using caution not to scratch the receiver. R E M O V I N G T H E B O LT A S S E M B LY To remove the bolt assembly it is preferred to first remove the trigger group, as explained previously. 1 With the gun inverted (trigger guard up position), push down on the cartridge stop while pulling outward on the bolt handle (Figure 5). Remove the bolt handle from the bolt. 2 While keeping the cartridge stop depressed, slide the bolt and bolt slide forward and out of the receiver (Figure 5-A). 3 The bolt and bolt slide can be separated for cleaning (Figure 5-B). Perform any cleaning of the bolt and receiver cavity as necessary. DO NOT DISASSEMBLE THE BOLT ASSEMBLY BEYOND THIS POINT. R E I N S TA L L I N G T H E B O LT A S S E M B LY 1 Reassemble the bolt and bolt slide. 2 Place the bolt assembly back in the receiver, bolt slide link end first (Figure 5-C). Line the rails on the bolt slide with the slots in the bottom of the receiver. 3 Guide the bolt slide link into its socket in the recoil spring follower (Figure 5-D). Push down on the cartridge stop while pulling outward on the bolt handle. FIGURE 5 15 FIGURE 5-A FIGURE 5-B Slide the bolt and bolt slide forward and out of the receiver. The bolt and bolt slide can be separated for cleaning. 4 To replace the operating handle, push down on the cartridge stop and insert the bolt handle in its respective slot in the bolt. IMPORTANT: It may be necessary to pull out on the bolt handle slightly until the cartridge stop clicks back in place (Figure 5-E). Failure to follow these instructions will result in the inability to load the magazine. 5 Open and close the action several times to make sure the bolt slide link and recoil spring follower are properly engaged. THREE SHOT ADAPTER/MAGAZINE CAPACITY The Gold shotgun is delivered with the magazine three shot adapter (plug) installed in the magazine, limiting magazine capacity to two shells in compliance with federal migratory bird regulations. If you do not wish to be limited to three shots -- when it is not required by law -- you can remove (or reinstall) the three shot adapter (plug) as follows: ALWAYS WEAR PROTECTIVE SAFETY GLASSES DURING THIS OPERATION. 1 First, make certain the gun is totally unloaded and the "safety" is "on safe." CHECK THE MAGAZINE, FEED MECHANISM AND CHAMBER TO BE SURE THEY DO NOT CONTAIN ANY SHELLS. 2 Unscrew the magazine cap and remove it. 3 The magazine three-shot adapter lays underneath the magazine spring retainer located in the forward end of the magazine tube. To 16 FIGURE 5-C FIGURE 5-D FIGURE 5-E Place the bolt assembly back in the receiver, bolt slide link first. Guide the bolt slide link into its socket in the recoil spring follower. Make sure the bolt handle clicks back into place. remove the magazine spring retainer, depress the magazine spring retainer tab, located in the window on the magazine tube while keeping your hand on the magazine spring retainer (Figure 6). SLOWLY REMOVE THE MAGAZINE SPRING RETAINER AS IT IS UNDER PRESSURE OF THE MAGAZINE SPRING (Figure 6-A). Remove the magazine 3-shot adapter. 4 Depress the magazine spring back into the magazine tube and replace the magazine spring retainer. Make sure the magazine spring retainer tab is locked in place in its slot in the magazine window. 5 Reinstall the magazine cap. If, at some future time you wish to limit your gun to three shots again, unscrew the magazine cap and remove the magazine spring retainer. Lightly press the three-shot adapter to FIGURE 6 FIGURE 6-A Depress the magazine spring retainer tab, and ease out the retainer. Remove the magazine spring and plug. 17 force the magazine spring rearward until the base of the three-shot adapter is level with the end of the magazine tube. Replace the magazine spring retainer and magazine cap. LOADING PROCEDURES AT ALL TIMES DURING THE LOADING PROCEDURE, BE SURE YOUR MUZZLE IS POINTING IN A SAFE DIRECTION AND THE SAFETY IS IN THE "ON SAFE" POSITION. There are two methods for getting a loaded shell into the chamber of your Gold shotgun. LOADING THE CHAMBER THROUGH THE EJECTION PORT 1 After making sure the safety is "on safe," pull the operating handle to the rear until the bolt locks in the open position. VISUALLY INSPECT THE CHAMBER, CARRIER AND MAGAZINE TO MAKE SURE THEY ARE CLEAR OF ANY OBSTRUCTIONS. 2 While pointing the muzzle in a safe direction, insert a cartridge of the proper gauge through the ejection port into the open breech (Figure 9). Press the carrier release button. This will deliver the shell to the chamber. The chamber is now loaded. 3 With the chamber loaded, load the magazine to full capacity. To load the magazine, insert a shell, of proper gauge, through the loading port at the bottom of the receiver, up into the magazine, using your thumb to position it fully forward in the magazine tube (Figure 9-A). Make sure the rim of the shell engages the cartridge stop and is held fully inside the magazine tube. It will make an audible click when fully inserted. 18