EN HR PL SL User instructions Upete za koritenje Instrukcja obsugi Navodilo za uporabo CDF 715 T DISHWASHER PERILICA POSUDJA ZMYWARKI POMIVALNI STROJ Congratulations! Thank you for choosing a Candy appliance; quality dishwashers which guarantee high performance and reliability. Candy manufacture a vast range of domestic appliances: washing machines, washer/dryers, cookers, microwave ovens, ovens and hobs, refrigerators and freezers. Ask your dealer for the catalogue with the complete range of Candy products. Please read this booklet carefully as it provides important information regarding the safe installation, use, and maintenance of the machine, together with some useful advice on how to achieve the best results from your dishwasher. For future reference please keep this instruction booklet in a safe place. CUSTOMER SERVICE AND GUARANTEE Your new appliance is fully guaranteed by the manufacturer for 12 months against electrical/mechanical breakdown excluding: A. Any faults which occur due to bad installation or misuse of the machine. B. Any faults which occur due to repair of, or interference with, the machine by any person not authorised by the manufacturer to carry out service. C. Any faults which occur due to any parts which are fitted to the machine which are not the original manufacturers parts. D. Any faults arising from non-domestic use or unusual or abnormal use of the machine. E. Any faults arising from operation at incorrect voltage. F. Any faults arising from incorrect operation of the machine. The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights. DESCRIPTION OF THE CONTROL OH I L M N A BCD E F G "SALT EMPTY" light "RINSE AID EMPTY" light "PROGRAM STATUS" LEDs DIGITAL DISPLAY "PROGRAM SELECTION" LEDs "OPTION SELECTION" LEDs A B C D E F G "ON/OFF" button "ECO" button "PLUS" button "1/2 FLEXI" button "DELAY START" button Open door "PROGRAMS" buttons H I L M N O AFTER SALES SERVICE For service and repairs call your local engineer on our national telephone number: DIMENSIONS: with working top Height Depth Width Depth with door open cm cm cm cm 85 60 60 120 without working top 82 57,3 59,8 117 GIAS Service Support Service CONTENTS Tel: 08705 400 600 (Eire 018301 666) TECHNICAL DATA: pag. 3 pag. 3 pag. 4 pag. 8 pag. 9 pag. 10 EN 50242 place load Capacity with pans and dishes Water supply pressure Fuse Power input Supply voltage 3 Description of the controls Technical data Operating the programmes and special functions The Waterblock system Water softner unit Programme selection 2 15 9 persons Min. 0,08 - Max 0,8 MPa (see rating plate) (see rating plate) (see rating plate) PROGRAM SELECTION AND SPECIAL FUNCTIONS (Use in conjunction with programme guide) "AUTOMATIC" programs Changing a running program Proceed as follows to change or cancel a running program: Program end The display will go blank and the last "PROGRAM STATUS" LED will light to indicate that the cycle has ended. A 5 second buzzer will sound (if not muted) 3 times at 30 second intervals to signal that the program has ended. The program end LED will light and the display will go blank. Dishes can now be removed and the dishwasher turned off by pressing the "ON/OFF" button or dishes can be loaded for a new cycle. Program settings Open the door and place dirty dishes inside the appliance. Press the "ON/OFF" button . The dishwasher is equipped with a dirt sensor, able to analyse water murkiness during all "AUTOMATIC" program phases (see program list); thanks to this sensor the washing cycle parameters are automatically adapted to the real quantity of dirt on dishes. Thus excellent washing results are guaranteed while optimising water and energy consumption. After pressing the "ON/OFF" button, the LED for the factory set is "recommended" (which is ideal for full load daily use) or the LED for the "Auto' Memory" program (see below) will blink. The length of the program will be shown on the display alternating hours with minutes [I.e: 1 h (1 hour) / 25 (25 minutes)]. IMPORTANT The dishwasher has two very practical functions: ( the "recommended" program ) for quick and sure selection; Hold down the current program button (with the LED on) for at least 5 seconds. All program LEDs will turn on for one second. The running program will be cancelled and the corresponding LED will start to blink. The display will go blank and the program end LED will turn on in the display At this point a new program can be set. IMPORTANT If, when the program button is held down, "00" blinks on the display, it means that there is water in the appliance. Close the door (if open) and wait until the dishwasher empties the water. When empty a new program can be set. Program interruption Opening the door when a program is running is not recommended especially during the main washing and final hot rinse phases. However, if the door is opened while a program is running (for example, to add dishes) the machine stops automatically and the display will flash the remaining time before the end of the cycle. Close the door, without pressing any buttons. The cycle will start from where it left off (if it is necessary, the appliance will make a short thermal anti-shock programme before). Option buttons IMPORTANT All options MUST be turned on or off, BEFORE starting the program. - the "Auto' Memory", function which saves a program used at least 3 times consecutively so that if you regularly use the same washing cycle each time you do not have to continually set the program thereby saving time and effort. To select an option, press the corresponding button (the LED will turn on). Option buttons must be pressed BEFORE starting the program for them to be accepted. To choose another program, press the corresponding button (the relevant LED will blink to confirm the selection). To start the program, press the selected program button again to confirm. The program starts automatically, the relevant LED will stop blinking and remain on and the cycle length will appear on the display. If the previously described operations were performed with the door open, the program will not start until the door is closed. 4 WARNING! Before starting a new programme, you should check that there is still detergent in the dispenser. If necessary, top up the dispenser. If there is any break in the power supply while the dishwasher is operating, a special memory stores the selected programme and, when the power is restored, it continues where it left off (if it is necessary, the appliance will make a short thermal anti-shock programme before). "ECO" button The "ECO" button provides over 20% time and energy savings by reducing the final water heating and drying times during the last rinse cycle. This option is recommended for light soil washes, and for when the dishes are not required perfectly dry straight away. If you want to get better drying, we advise to leave the dishwasher door slightly ajar at the end of the cycle, to allow for a natural circulation of air inside the dishwasher. IMPORTANT A running program can be interrupted without opening the door by pausing the dishwasher. To pause, hold the running program button down for at least 2 seconds and release when the corresponding LED starts blinking. Simply press the program button again to restart the cycle from where it left off (the LED will stop blinking and remain on). Program operations "PLUS" button When a program is running, the time until the end of the cycle will be displayed and the 4 "PROGRAM STATUS" LEDs: = "WASH" = "RINSE" = "DRY" = "END" will light singularly and in sequence to indicate the current phase The "PLUS" option always guarantees the best results by more effectively dealing with heavier soiling. By using this option, the strength of the selected cycle will be increased, adding one rinse and increasing the temperature of the water in the washing phase where foreseen. This option is recommended for very dirty dishes or when dirty dishes may not have been pre-treated allowing the soiling to dry up. 5 WARNING! If you open the door during the drying cycle, an audible audio signal advises you that the drying cycle has not yet completed. "1/2 FLEXI" button To ensure that your dishwasher meets all your requirements, this button allows you to select: 1) Half Load Top Basket By selecting this option dishes are washed in the top basket and cutlery in lower basket. Half Load Lower Basket By selecting this option dishes are washed in the lower basket only. Buzzer mute The buzzer may be muted as follows: With the dishwasher off, hold down the second option button (from the left) while simultaneously pushing the "ON/OFF" button. "b1" will appear on the display to indicate that the buzzer is on. Press the same option button (second from the left) within 5 seconds ("b0" will appear on the display to indicate that the buzzer is off). Wait for a buzzer to sound to indicate that the settings were saved. To turn the buzzer on again, follow the same procedure ("b1" will appear on the display to indicate that the buzzer is on). The dishwasher is able to signal a series of faults in the display. AUTOMATIC FAULT SIGNALS FAULTS CAUSE No water (inlet hose closed). SOLUTION Turn off the dishwasher, open the inlet hose and reset the cycle. E2 appears on the display and the buzzer sounds. 2) E3 appears on the display and the buzzer sounds. The machine cannot drain water. Check if the drain tube is bent or if the siphon or filters are clogged. If the problem persists, contact Customer Service. "DELAY START" button Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. Proceed as follows to set a delayed start: Press the "DELAY START" button ("00" will appear on the display). Press the button again to increase the delay in hours (each time the button is pressed the delay is increased by 1 hour to a maximum of 23). To start the countdown, press the selected program button (the relevant LED will stop blinking and remain on and the start time delay will be shown in the display). At the end of the countdown, the program will automatically start and the length of the selected cycle will be shown in the display. Proceed as follows to cancel a delayed start: Hold the selected program button down for at least 5 seconds. Delayed start cancellation is confirmed when the selected program LED starts to blink. The display will go blank and the program end LED will light (any selected options will also be cancelled and the corresponding LEDs will turn off). At this point, a new program and option buttons must be set to start a new program as indicated in the "PROGRAM SETTINGS" section. 6 E4 appears on the display and the buzzer sounds. Water leak Check if the drain tube is bent or if the siphon or filters are clogged. If the problem persists, contact Customer Service. Contact Customer Service. E5 appears on the display and the buzzer sounds. WARNING! To ensure the correct operation of the anti-overflow safety device, it is recommended not to move or to tilt the dishwasher during operation. If it is necessary to move or to tilt the dishwasher, first make sure the washing cycle is finished and that no water is left in the tank. E6 appears on the display and the buzzer sounds. E8 or Ei appear on the display and the buzzer sounds. Electronic temperature control fault. Electronic control fault. Contact Customer Service. The water heating element is not working correctly or the filter plate is clogged. Clean the filter plate. If the problem persists, contact Customer Service. 7 THE WATERBLOCK SYSTEM The waterblock system has been designed to improve the safety of your appliance, particularly when the machine is left unattended. The waterblock system actually prevents flooding which might be caused by a machine malfunction or as a result of a fracture on the pipes. How does waterblock work The sump located in the base of the appliance collects any possible water leakage and operates a sensor which subsequently activates a valve placed under the water tap and stops any water from the supply even with the tap fully opened. If the box containing the electrical parts is damaged, remove the plug from the socket immediately. To ensure perfect operation of the safety system, box "A" with the hose, should be connected to the tap as shown in figure "1". The inlet hose should not be cut, as it contains parts under load. If the hose is not long enough for correct connection, it must be replaced with a longer one. The hose can be obtained from your Service Agent. This dishwasher is also equipped with an anti-overflow safety device which, if water exceeds normal levels due to malfunctions, automatically blocks water flow and/or drains excess quantities. WATER SOFTENER UNIT Depending on the source of the supply, water contains varying amounts of limestone and minerals which are dep ...