Cannon FITZROY INBUILT INBUILT MODELS FITZIB-SDSEB-NG FITZIB-SDSEB-LP USER INSTRUCTIONS INSTALLATION INSTRUCTIONS SERVICE INSTRUCTIONS This heater is approved for use with Natural and Propane gases. Please leave instructions with the owner Contents Contents Warranty Distributor Safety warnings What to do if you smell gas Warnings Standards User instructions Operating instructions Cleaning Flame characteristics Heater specifications Installation instructions Clearances Fitment of cabinet depth spacer Installation into a masonry/brick or mock fireplace Installation WITH a flue connected Installation WITHOUT a flue connected Sealing 15 16 17-18 9 10-14 6-8 4-5 2 3 Gas connections Log installation Gas control Gas pressure point Gas pressure adjustment Installation tips Trouble-shooting Connections Service instructions General To replace the primary glass To replace outer glass To replace the gas control To replace the ignition (module) device To replace the room circulation fan To replace the fan pressure switch To remove the heat exchanger To replace the burner and spark/sense electrode Wiring diagram Data plate For service to this appliance 19 20-21 22-24 2 Warranty The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available through the CANNON distributor. (Details below or on page 23). Consumers are responsible for service person's travel outside normal service areas (approximately seventy (70k) radius from the nearest Cannon dealer's location), local cartage, and normal maintenance as described in this manual. Any product subjected to misuse, abuse, negligence, accident or alteration will have its warranty voided. The defacement of serial plate will have its warranty voided. If installation is not carried out in accordance with manufacturer's instructions, this warranty may be void. The customer must keep their "Tax Invoice" as proof of purchase of this product and compliance certificate as proof of required installation. Model number: ______________________________________ Serial number: _______________________________________ Date of manufacture: _________________________________ Date installed: _______________________________________ Compliance Certificate No: ____________________________ Don't risk your appliance warranty Only a licensed person will give you a Compliance Certificate, showing that the work complies with all the relevant standards. And only a licensed person will have insurance protecting their workmanship for 6 years. So make sure you use a licensed person to install this appliance and ask for your Compliance Certificate to ensure the manufacturers appliance warranty will be honoured. Distributor This appliance is designed, manufactured and distributed by: Tel: 1300 727 421 3 Safety warnings Please read this manual before installing and using the heater. What to do if you smell gas 1. Turn OFF the main gas supply. 2. Extinguish any open flame. 3. Open windows. 4. Do not touch electrical switches. 5. Do not use your telephone. 6. Call your gas supplier immediately from a neighbour's phone. Warnings 1. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to other sections of this manual for correct procedures, or consult with place of purchase, a licensed plumber, a gas supplier or the CANNON distributor listed in this manual. 2. Do not build the heater into bookcases or walls. Install only on locations as referred to on these installation instructions. 3. Due to high temperatures the room heater should be located out of traffic and away from: · · · Furniture and draperies. Combustible materials. Gasoline and other flammable liquids. Do not place clothing or other flammable material on or near the heater. 4. Keep curtains*, clothing, furniture and other flammable materials at least 900mm from front and sides of the heater. * At the owner's discretion curtain clearance can be less than 900mm as long as they are restrained from the front, top and sides of the heater. The manufacturer takes no responsibility if curtain clearance is less than 900mm and not restrained. 5. Children and adults should be alerted to the hazard of high surface temperature and should take care to avoid burns or clothing ignition. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 6. Never attempt to burn paper or any other material in the heater. 7. Do not place articles on or against this appliance. Do not use or store flammable materials near this appliance. Do not spray aerosols in the vicinity of this appliance while it is in operation. 4 Do not modify this appliance. 8. If removed, the glass window must be put back onto the unit prior to operating the heater. 9. Installation and repairs should be performed by a licensed service person only, refer to back of brochure for service number. 10. For installation into a non-combustible fireplace, i.e.: masonry or brick or into a mock fireplace, i.e. timber or plasterboard, the chimney and base should be of sound construction and be free from cracks and holes (to ensure that sufficient flue draught can be generated). Note: when installing into a mock fireplace a mock fireplace installation kit must be used. 11. The heater must be properly installed in a working chimney or connected to a venting system. Operation of this heater, when not connected into a working chimney or a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. 12. Testing the effectiveness of the flue. Before testing the flue confirm air vents are unobstructed. If an exhaust fan or other heating appliances are present switch them on. This is to test that there is no interaction between the Cannon heater and other appliances. Refer AS5601. For `air movement not to affect appliance' see clause 5.3.1. For `air supply to appliance' see clause 5.4.1. For `ventilation requirements' see clause 5.4.3. 13. The appliance should be inspected prior to use, with regular inspections (annually) to be made by a licensed service person. It is important that circulating air passageways of the appliance be kept clean, dirt and lint free, for a safe and efficient operation of the heater. 14. On first lighting your heater a smell may occur due to its new condition. This is quite normal and will disappear after a few hours use at the maximum control position. Important: When this heater is operating the mesh guard/glass front is hot. The mesh guard, or glass front, fitted to the heater conforms to Australian Standards requirements. The guard is fitted to this appliance to reduce the risk of fire or injury from burns and no part of it should be permanently removed. For protection of young children or the infirm, a secondary guard is required. Standards This appliance meets the following standards: Standards Australia: AS/NZS 3100 AS 5601 AS 4553:2008 5 User instructions Operating instructions 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord. 1 2. For control layout refer to figure 2 2 3. To turn heater on press switch to POWER ON position. There is a 5 second delay before the burner ignites. At this setting the burner is on LOW and the fan speed is on LOW. Refer figure 3. The burner will ignite on both HIGH and LOW settings. 3 4. To turn burner to HIGH setting, press switch for HIGH setting. Refer figure 4. 4 6 5. To increase the fan speed to MED, press switch for MED setting. Refer figure 5. 5 6. To increase the fan speed to HIGH, press switch for HIGH setting. Refer figure 6. 6 7. To turn the burner to LOW setting, press switch for LOW setting. Refer figure 7. On low burner setting it is more efficient to operate the fan speed on LOW. 7 8. If the burner fails to ignite, wait 20 seconds and repeat the ignition procedure. Refer figure 8. To turn burner OFF To turn burner ON 8 9. In case of power failure return the switches to the OFF setting (refer figure 2). When the power returns wait 20 seconds for any unburnt gas to vent and start re-ignitions as per point 3. 7 Cleaning All cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. For heater fitted with the glass front: All cleaning should be carried out when the heater is cold. Clean the outer glass with a liquid solution `Windex' or similar. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the heater glass front since they can scratch the surface, which may result in shattering of the glass. Internally the heater should only be cleaned by an authorised service person listed in this manual. If your heater requires attention contact your supplier or authorised service person listed in this manual. Flame characteristics The heater flame should be stable, no lifting from the burner and the logs should glow after approximately 15 minutes operation on HIGH setting. The heater is a fuel effect unit and is designed to operate with luminous flames and may exhibit slight carbon deposit on the logs. If any excess carbon build-up on logs, or the burner flame is unstable, contact Sampford IXL in your state. (See phone contact no page 24). Important: The appliance should be inspected before use and at least annually by an authorised service person. More frequent cleaning may be required due to excessive lint build-up from carpeting, bedding materials, pet hair, etc. It is imperative that control compartments, burners and circulating air passage ways of the appliance be kept clean. Do not use this fire if the glass is cracked or with the glass safety screen removed. Do not use fire with broken or missing logs. 8 Heater specifications Gas type: The data label is located on the fan chamber base, Gas consumption: rear of lower fascia. Energy output: Note: Natural or Propane gas, as indicated on data label 26.0 MJ/hr 21.45 MJ/hr (5.96 KW) 4 stars Approved to AS 4553:2008. Natural gas: 0.75 kPa Propane gas: 2.65 kPa Integral part of controller 1.13 kPa (NG) 2.75 kPa (Propane) 3 speed Electronic direct spark 240 VAC 10 A 90 VA maximum Height: 605mm dimensions* Width: 700mm Depth: 393mm · Glass front · Silver trim (comes complete with mesh guard) · Spacer kit · 3 sided surround · 4 side surround in black & stainless steel · Console kit Refer fig. 9. *Note: when installing into a mock fireplace a mock fireplace installation kit must be used. Energy star rating: Heater type: Operating pressure: (at the burner) Gas regulator: Min. inlet pressure: Fan: Controller: Power requirement: Power consumption: Minimum cavity dimensions: Optional Accessories: Overall dimensions: 9 9 Installation instructions 1. This appliance is to be installed by an authorised service person only. 2. This appliance shall be installed in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, and AS5601 the Australian Standard for gas installations. Refer also to AS5601 for pipe sizing tables. 3. Remove the heater from the carton and remove the three transit screws. Check that the heater is suitable for gas available. Refer to the data label located on fan chamber base, rear of lower front cover. (Please dispose of packaging appropriately, keep away from children). Clearances 4. Ensure the minimum clearances to combustible construction are maintained during installation, including adequate space for the proper operation and servicing of the heater. For clearances to furniture and curtains refer to warning on page 4. For minimum clearances refer figures 10 and 11. Note: Ensure that the combustion air opening under the heater is not obstructed. 10 11 A CLEARANCE OF 50mm MUST BE MAINTAINED BETWEEN THE REAR OF THE CABINET AND THE REAR WALL OF THE FIRE PLACE. Fitment of cabinet depth spacer The clearance is required for correct fluing of the appliance. If the clearance is less than 50mm a cabinet depth spacer must be fitted. The spacer can be ordered from the Cannon distributor. Order specification for the spacer is `Fitzspacer". This is the requirement for installation into a masonry or brick fireplace without ...