User manual CANON PIXMA MP600

Easy Setup Instructions Start Here Photo All-in-One Unpack the Machine QT5-0683-V02 · Please confirm the included items against the illustration printed on the lid of the packing box. · A USB cable is necessary to connect the machine with your computer. 1 Prepare the Machine a Place the machine on a flat and horizontal surface, and do not place any objects in front of the machine. Open the Sheet Feeder Cover and pull the Paper Support, then the Paper Output Tray and open the Output Tray Extension. 2 Install the Print Head d Use the { or } button on the Operation Panel to select the language for the LCD, then press the OK button. 3 Install the Ink Tanks a Peel back the orange tab completely and remove the plastic wrapper from the ink tank. 4 Align the Print Head a Pinch the Paper Guide and slide it to the left end. Paper Support a Remove the Print Head from its package. Hardware setup and Print Head alignment is complete. Extension Caution Before turning on the machine, remove all of the shipping tapes. Important Do not connect the USB cable until after the software is installed. Note To open the Paper Output Tray, put your finger in the rounded indent of the tray and open it gently. (1) Press the { or } button to select the language. (2) Press the OK button. Caution There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. If the orange-colored protective film is not removed completely, problems with printing may occur. Paper Guide b Twist off and discard the orange Protective Cap protective cap located on the bottom of the ink tank. Do not press! Ink Port Important If an unintended language is displayed on the LCD, press the Back button to return to the Language selection screen. b Remove the orange protective cap from the Print Head and discard it. Electrical Contacts Once the message "Install the print head and set the ink tank." appears, go to e. Electrical Contacts b Load a sheet of letter- or A4-sized e Open the Scanning Unit (Printer Cover) b Plug the power cord in the back of the until it locks into place. The Print Head Holder moves to the center. Protective Cap Important · Do not touch the electrical contacts. · Do not touch the ink port. Print Head Nozzles c Insert the ink tank into the right-hand machine and connect the other end to the wall outlet. Note Do not touch the print head nozzles or the electrical contacts. slot and press the mark on the ink tank until it clicks into place. blank paper in the Auto Sheet Feeder, align the paper with the right side of the Cover Guide, then slide the Paper Guide against the paper stack. Paper Guide Print Side c Firmly raise the Print Head Lock Lever until it stops.The Print Head Lock Lever may feel heavy. Cover Guide Scanning Unit (Printer Cover) Easy-Scroll Wheel c Make sure that Yes is selected in the d Insert the Print Head. d Make sure the ink lamp lights red. Refer to the color guide on the Print Head Lock Lever. Important Make sure that the Document Cover is closed. c Open the Operation Panel, then press the ON/OFF button to turn on the machine. message requesting head alignment, then press the OK button. Turn the Easy-Scroll Wheel left or right to easily select a menu or a setting item. For details, refer to "Basic Operation for the Operation Panel" in the Quick Start Guide. * You can also use the {, }, [, or ] button to select. Important For your safety, always firmly grip the areas illustrated when opening the Scanning Unit (Printer Cover). Do not touch! f Open the Inner Cover. Write down the serial number located inside the machine. You will need this to register your product. e Lower the Print Head Lock Lever carefully. e Close the Inner Cover and the Scanning Unit (Printer Cover). Note Print Head alignment takes about 6 minutes to complete. Do not start another operation here. The pattern is printed. And Print Head is aligned automatically. OK Inner Cover Serial Number Location Important If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center. Cassette For information on how to load paper in the Cassette, refer to "Loading Paper in the Cassette" in "Loading Printing Paper" of the Quick Start Guide. Important · For your safety, always firmly grip the areas illustrated when closing the Scanning Unit (Printer Cover). · The machine starts operating. Wait about 2 minutes until the machine stops making noise. Note · The pattern is printed in black and blue. · When Automatic Print Head Alignment cannot be executed correctly, the message "Auto head align has failed." is displayed on the LCD. Refer to "Error Message is Displayed on the LCD" in the User's Guide on-screen manual. Windows® MP Drivers Installation Macintosh® MP Drivers Installation do W in Note · The screens below refer to Windows XP Service Pack 2 installation. Screens may vary depending on the operating system you are using. · For Windows XP or Windows 2000, log on to Windows as a member of the Administrators group before continuing. · Before installing the driver, disable all anti-virus programs and automatically loading programs. f Read the License Agreement carefully and click Yes. M ac in to sh w s Follow the on-screen instructions to install the software. If a message asking for your confirmation to restart your computer appears, click OK. machine with a USB cable, then turn the machine on. The software will begin identifying the printer port being used. Important If you cannot go to the next procedure after 3 minutes, refer to "Troubleshooting" instructions in the User's Guide on-screen manual. Important Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.2.7 or earlier are not supported, do not connect the machine to these. · · · · Note Use Mac OS X v.10.2.8 to 10.4.x. The screens below refer to Mac OS X v.10.4.x installation. Screens may vary depending on the operating system you are using. Log on as an Administrator before continuing. Before installing the driver, disable all anti-virus programs and automatically loading programs. g When the list of applications to install appears, confirm the contents, then click Install. Note Move the cursor over items to display explanations of each application. g When the Printer Connection screen appears, connect the h Read the License Agreement carefully and click Yes. a Turn off the machine. (1) Press the ON/OFF button. (2) Make sure that the POWER lamp stops flashing. Follow the on-screen instructions to install the software. Note When the User Registration screen appears, follow on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine. See Step 1- f on the front page. i Follow the on-screen instructions to register your product. a Connect one end of the USB cable to the computer, the other to the machine. Note Make sure the machine is turned on. b Turn the computer on and start Windows. Important If you see the Found New Hardware Wizard, remove the USB cable. Click Cancel to quit the screen. Next, turn off the machine. Then proceed from step 3 to install the MP Drivers. j When the Installation completed successfully screen appears, click Restart. b Turn on your Mac. c Insert the Setup CD-ROM. The setup program should run automatically. Note The setup program should run automatically. If the installer in the CD-ROM does not run automatically, click Start and select My Computer, then double-click the CD-ROM icon . c Insert the Setup CD-ROM. Note If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop. The system is restarted automatically. *When using Mac OS X v.10.2.8 to v.10.3.3: Restarting the computer while connected to the machine may cause the machine not to be detected. To resolve this, either unplug the USB cable then plug it back in again, or turn the machine off then back on again. d Double-click the Setup icon. h Follow the on-screen instructions to register your product. Note When the User Registration screen appears, follow on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine. See Step 1- f on the front page. d When the main menu appears, click Easy Install. e When the Authenticate screen appears, enter your k After restarting the computer, start Printer Setup Utility administrator name and password. Click OK. If you do not know your administrator name or password, click , then follow the on-screen instructions. i When the Installation completed successfully screen appears, click Exit. (start Print Center if you are using Mac OS X v.10.2.8) and then check that the printer name you want to use is shown in Printer List. If the printer name is not displayed, click Add to add the device. For more detailed instructions, refer to the Mac on-screen Help. Now you have completed installation of the software. Note · Select Easy Install in order to install the MP Drivers, on-screen manuals, and application software. Select Custom Install in order to choose the options you would like to install. · To install Adobe® RGB (1998), click Custom Install and follow the on-screen instructions. If you are using Windows Me/98, Adobe RGB cannot be installed. f When the main menu appears, click Easy Install. e When the list of applications to install appears, confirm the contents, click Install. Note Move the cursor over items to display explanations of each application. If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. Now you have completed installation of the software. Note Select Easy Install in order to install the MP Drivers, on-screen manuals, and application software. Select Custom Install in order to choose the options you would like to install. Part no. QT5-0683-V02 © 2006 Canon Inc. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the U.S. and/or other countries. Macintosh and Mac are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. Adobe and Adobe RGB (1998) are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. All other product and brand Printed in Thailand. names are trademarks of their respective owners. Specifications subject to change without notice.