User manual CARDO SCALA-RIDER TEAMSET

scala-rider TeamSet TM CARDO SYSTEMS INC. INTRODUCTION This Quick Guide will get you started using the scala-rider TeamSet. For more detailed information, including safety precautions, please download the User Manual from our website at www.cardowireless.com. Before using the scala-rider TeamSet, please familiarize yourself with the Bluetooth® functionality of your cellular phone. The retail box of the scala-rider TeamSet contains two headset units: One device for the driver and a second device for the passenger. The driver unit (yellow logo) includes a Bluetooth module that connects with a Bluetooth phone, and an intercom module to communicate with the passenger. The passenger unit (green logo) contains only an intercom module that allows communication with the driver. The passenger unit cannot connect to a phone. 2 Driver unit (yellow logo) (with BT and Intercom capabilities) Passenger unit (green logo) (with Intercom capability only) COMPONENTS Control Button Status Light Intercom Button Volume Up Charging Jack (Here shown with closed cover tongue) Sliding Panel Volume Down Tab Microphone Sliding Plate Right speaker (long cord) Left speaker (short cord) One headset for the driver and one headset for the passenger. NOTE: The use of two speakers may be illegal in certain jurisdictions. Please check the local regulations and act accordingly. 3 IMPORTANT The scala-rider TeamSet is a water-resistant device, designed for use under moderate rain or snow conditions. However, the headset is not waterproof and should not be used under severe weather conditions. The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device. BEFORE USING (CHARGING THE HEADSET) Make sure that both headsets are fully charged for at least 5 hours before initial use. 1. Connect the wall charger to the headset's Charging Jack (located between the two Volume buttons). 2. While charging, the red Status Light illuminates (it may take up to 15 seconds until the red Status Light illuminates). When charging is complete the Status Light will turn off. GENERAL INSTRUCTIONS All headset functions are controlled either by: · Pressing the Control or Intercom Button either for a short period of less than a second or a long period of over three seconds Or · Short pressing the volume up and volume down buttons. 4 TURNING THE DRIVER HEADSET ON FOR THE FIRST TIME The driver unit (yellow logo): The driver unit permits two communication modes: · Mobile Phone connections with third parties · Intercom connection with the passenger In order for the headset to work with your cellular phone, they must first recognize each other. This process is called "pairing", and only needs to be performed once for each phone. 1. Turn on your phone and make sure its Bluetooth function is activated. 2. With the headset turned off, press and hold the Control Button for ten seconds until the red and blue Status Lights begin flashing. 3. Search for Bluetooth devices on your phone by following the phone's instructions. 4. After a few seconds the phone will list the scala-rider TeamSet as a discovered device. Select it and follow your phone's instructions to accept the pairing. 5. When prompted enter 0000 (four zeros) as your PIN or passkey. 6. Your phone will confirm that pairing has succeeded. Note: If pairing is not completed within two minutes the headset will return to Standby mode. Your headset can pair with up to eight phones, and will automatically connect to the last phone connected to the headset. 5 The Passenger Unit (green logo): This unit is solely intended for intercom connection with the driver and it cannot initiate or receive a phone call. To turn on the Passenger Unit, press the Control Button until the blue Status Light illuminates. NOTE: The Driver and Passenger Units are already factory-synchronized for Intercom communication with each other, and do not require any synchronization by you. SYNCHRONIZING INTERCOM BETWEEN THE PASSENGER AND DRIVER HEADSETS The two headset units (Driver and Passenger units) are supplied factory synchronized for Intercom communication with each other. Therefore, you do not need to perform the synchronization between these devices. However, if you have purchased these units separately and not in the TeamSet Retail box, you need to synchronize the devices yourself by proceeding as follows: 1. Simultaneously press and hold the Intercom Buttons of both devices for at least 10 seconds while watching the Status Light on the Passenger unit. 2. Once the Status Light on the Passenger unit lights steady red, wait three seconds and then release both Intercom Buttons. 3. If successful, the steady red Status light on the Passenger unit will switch to a steady blue light for a few seconds, then begin flashing blue. Your two headsets are now synchronized for Intercom communication. 4. If the synchronization has failed, the steady red Status light on the Passenger unit will turn off without switching to steady blue for a few seconds, and you must repeat the synchronization procedure. 6 ATTACHING THE SCALA-RIDER UNITS TO YOUR HELMETS Perform this procedure for both the driver and passenger helmets. 1. Use the enclosed Allen Wrench to loosen the two screws on the Back Plate. 2. Slide the Back Plate between the internal padding and the external shell of the helmet. (If the external shell is too thick, use the supplied plastic Extension Pad by loosening the screws and fitting the extention pad between the Back Plate and the main body of the clamp). 3. Adjust the clamp's location so that the microphone is located in front of your mouth, and then tighten the screws. Attach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for left ear & long speaker cord for right ear), or use the supplied Velcro pad. Allen Wrench Back Plate CORRECT INCORRECT NOTE: The microphone must be positioned vertically and not horizontally. 7 4. Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING THE HEADSET FROM THE HELMET Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you store your headset in the enclosed carrying pouch when not in use. Press here to remove 8 DRIVER'S UNIT FUNCTIONS DESIRED RESULT: G E N E R REQUIRED ACTION: A L F U N C T I O N S Turn on the headset Turn off the headset Increase the volume Decrease the volume P H O N Press the Control Button steadily for at least 6 seconds Press the Control Button steadily for at least 3 seconds Short press the Volume Up Button. Short press the Volume Down Button. E F U N C T I O N S Answer a call Reject a call Terminate a call Voice Dial Redial Enable/Disable voice command feature Short press the Control Button or speak loudly any word of your choice. Short press the Intercom Button or remain silent for 15 seconds. Long press the Intercom Button. For some mobile phones you may need to press the Control Button to end the call. During standby, short press the Control Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. During standby, long press the Intercom Button Long press the volume up and down buttons simultaneously until you hear a beep. The default status is voice command enabled. 9 DRIVER'S UNIT FUNCTIONS (continued) DESIRED RESULT: I N T E R C REQUIRED ACTION: O M F U N C T I O N S Start using the intercom Terminate the operation of intercom Conference Call (add passenger to an active call) End Conference Call (release passenger from a conference call) DESIRED RESULT: Turn on the headset Turn off the headset Start using the intercom During standby, start speaking loudly to activate the intercom Stop speaking. The audio connection will be terminated within 25 seconds. During an active phone call, tap the Intercom Button. During a conference call, tap the Intercom Button. PASSENGER'S UNIT FUNCTIONS REQUIRED ACTION: Press the Control Button steadily for at least 3 seconds Press the Control Button steadily for at least 3 seconds During standby, start speaking loudly to activate the intercom Terminate operation Stop speaking. The audio connection will be terminated of intercom within 25 seconds. Enable/disable During standby, short press the Control Button. Always On Intercom One tone = Always On intercom. Two tones = Voice Controlled (VOX) intercom Increase intercom volume Short press Volume Up Button Decrease intercom volume Short press Volume Down Button 10 DRIVER'S UNIT STATUS LIGHTS The Driver Headset uses the following Status Lights to display its current state: Status Light None Alternating Red/blue flashes 1 blue flash every 3 seconds 2 blue flashes every 3 seconds 1 red flash every 3 seconds 2 red flashes every 3 seconds Steady red Status Headset is off Pairing mode Standby ­ No call is in progress Call being initiated or in progress Battery is low Call being initiated or in progress and battery is low Headset is being charged PASSENGER'S UNIT STATUS LIGHTS The Passenger Headset uses the following Status Lights to display its current state: Status Light None One blue flash every 3 seconds Steady red Status Headset is off Headset is on Headset is being charged 11 AUDIO TONES With the exception of the actions below, all other actions are followed by a single tone to confirm that the headset has accepted the command. Action Enable/Disable Always On intercom Intercom on other side is not enabled or off and you start speaking Tone One tone = Always On intercom Two tones = Voice Controlled (VOX) intercom 2 beeps to alert you that the other side is not available TROUBLESHOOTING Problem Action Phone-Related Problems (Driver Unit with Bluetooth Phone) Unsuccessful Bluetooth Pairing 1. If listed, delete scala-rider from your paired device list of your phone. 2. Turn off the phone and headset. 3. Remove the battery from the phone, then place the battery back in the phone. 4. Repeat the pairing process as described above. I cannot hear stereo sound The two speakers provide only dual mono signals. Can't answer calls or perform 1. Make sure that the scala-rider headset is turned voice dialing by pressing the ON and in standby mode with the blue Status Control Button Light slowly flashing. 2. Verify that the Bluetooth function on your phone is set to ON. 12 Cannot terminate calls using the intercom button Can't answer phone calls using the Voice Command (VC) feature. I cannot perform redial 3. Verify that the scala-rider headset is the paired headset to your phone. 4. Reconnect the phone and headset by short pressing the Control Button on the headset, or connecting them manually by using your phone's menu. 5. Check the definitions and settings on your phone. 6. Repeat the pairing process as described in TURNING THE DRIVER HEADSET ON FOR THE FIRST TIME, page 5. Your phone supports only the Bluetooth headset profile and not the handsfree profile. Therefore you must use the Control button to answer or terminate calls. 1. Make sure that you speak the word loudly after prompting 2. Close the helmet visor. 3. Make sure that the VC feature is activated (see Driver's Unit Functions, page 9) 4. The VC feature works well while driving up to 70 km/h or 44 mph with a 3/4 helmet and up to 120 km/h or 75 mph with a closed full faced helmet. High-end helmets may get better results. 1. Make sure that the call list on your phone is not empty. 2. The Redial feature works only with mobile phones that also support the Bluetooth handsfree profile. Check whether your phone supports this profile. 13 Battery does not provide at least five hours of talk time I'm trying to reject incoming calls by remaining silent, but the phone continues to ring. Red Status Light does not light steady when charger is connected. I hear crackling noises Sound deteriorates when the phone is in my back pocket. 1. Make sure your scala-rider headset is fully charged. Charging time is up to 5 hours for an empty battery. When the headset is connected to the charger and it is fully charged, the red Status Light turns off. 2. You may have inadvertently left the Always-On Intercom on. 1. Make sure the VC feature is enabled 2. Reject feature works only with mobile phones that support Bluetooth hands-free profile. Make sure your mobile phone supports this profile. 1. Make sure the Charging Jack is firmly plugged into the headset and wait 5 seconds 2. Disconnect the Charging Jack wait a few seconds and plug it back in. 3. When the headset is fully charged the red light turns off. 1. Possibly caused by nearby interference. If you have a GSM phone and your headset is too close to phone, noises may be heard. 2. Headset and mobile phone are more than 30 ft. (10 m) apart or there are major obstacles (such as concrete walls) between the headset and mobile phone. Some mobile phones emit weaker Bluetooth signals than others, resulting in reduced sound quality, especially when the phone is close to your body. Suggestion: Move the phone to your breast 14 The party I am speaking to complains about insufficient audio quality pocket or at least to a front pocket on the same side you wear your headset. 1. Close helmet cover under high speed conditions. 2. Make sure the microphone is in front of your mouth. The microphone should be positioned vertically as described on page 7. Intercom-Related Problems (driver/passenger) Cannot initiate conversation 1. Try speaking louder. with other party 2. Make sure the microphone is located in the (driver/passenger) correct place as described in this guide 3. Make sure that intercom is not disabled in both driver and passenger units. (To toggle Intercom operation, tap the intercom button. You will hear one beep when enabled; two beeps means that the intercom is disabled.) I keep hearing the speaker 1. If you drive with an open face helmet at 60 even though no-one is km/h (37 mph) or use a closed helmet above speaking (audio connection 110km/h (68 mph), the wind noise may activate is not released). the intercom connection between passenger and driver. 2. You can disable the intercom by following the instructions shown above. 3. Make sure the microphone is placed at the correct location as described in this guide When I receive an incoming This is normal behavior. The driver may choose call, the intercom disconnects to bring the passenger into a conference call by short pressing the Intercom Button. 15 PLEASE NOTE: THE USE OF THIS PRODUCT IS AT YOUR SOLE RISK AND MAY BE ILLEGAL IN CERTAIN JURISDICTIONS. ALL WAIVER PROVISIONS CONTAINED IN THE COMPREHENSIVE USER MANUAL APPLY. IF YOU ARE UNWILLING TO ACCEPT ANY OF THE SAID WAIVER CONDITIONS YOU MAY RETURN THE PRODUCT FOR A FULL REFUND ACCORDING TO COMPANY POLICY TERMS. SUPPORT For additional information visit our website at www.cardowireless.com, or call us at: Toll-free USA: 1-800 488-0363 Europe: +49 89 450-36819 Developed and Manufactured by: QGTS_027_0566 www.cardowireless.com