INITIAL SETUP WALL/DESK USE A wall mount bracket is included and can be installed if needed. Tightly coil the telephone cord around the four guides on the inside of the wall mounting bracket. Pull the telephone cord through the center opening on the wall mounting bracket. Refer to the drawing. The handset can be charged face out or face down, even when wall mounted. B CALLER ID SERVICE OPTIONS You must subscribe to a Caller ID service (available from most local telephone companies) in order to receive Caller ID information. Most Caller ID services offer the following two options: 1.Standard Caller ID with name and number The name, phone number and local time (if available) of the incoming call are received after your phone rings. 2.Call Waiting Caller ID with name and number The name, phone number and local time (if available) of the incoming call are received after your phone rings. If you are on the phone and receive another call, you will hear a tone, telling you there is a call waiting. The Call Waiting Caller ID information will appear on the display. NOTE: s The display illustrations in the remainder of this section are presented with the assumption that your Caller ID service provides both name and number. If you have a number-only service, the name will be blank. CALL WAITING & CALLER ID 1 TALK D Once you hear the confirmation tone, you to answer the call and can press automatically retain all the Caller ID information received. "BLOCKED" AND "UNAVAILABLE" MESSAGES If a caller chooses to partially or completely "block" Caller ID information, a message will appear on the display indicating that the name and/or phone number has been blocked. If, for any other reason, the name and/or number information is currently not available from your local phone company, an "Unavailable" message will appear on the display. The time and date information for the call will still be recorded into the CP-2070's memory. STORING NAMES AND NUMBERS IN AUTODIAL You may store up to 20 of your most frequently dialed names and numbers into the autodial memory. Autodial names can be up to 16 characters long, and the accompanying phone numbers can be up to 24 digits each. 3 KEY 4 5 6 7 8 9 Press the or to locate the number you wish to edit. TONE/PULSE SWITCH This switch tells the CP-2070 to dial out with either touchtone or pulse signals to match the service you have with your local telephone company. The CP-2070 is shipped with the TONE/PULSE SWITCH in the TONE position. If you do not have touchtone service, set the switch to pulse on the back of the charging cradle. TONE = for Touchtone systems PULSE = for Rotary dialing or Pulse systems PULSE TONE ANSWERING CALLER ID CALLS When you receive a call, the CP-2070 will receive the Caller ID information from your phone company within the first two rings. Caller ID information will display even if the ringer is set to off. When all of the data is received, you will hear a low-high confirmation tone and the Caller ID information will appear on the display: SMITH JAN 1 310 555 1234 1/22 09:01 AM NOTE: s If you press TALK before you hear the Caller ID confirmation tone, the Caller ID information for that call will be lost. ANSWERING CALL WAITING CALLER ID CALLS If you subscribe to a Call Waiting Caller ID service with your telephone company and you program Call Waiting Caller ID to "ON," the CP-2070 can receive a Caller ID call while you are on the line with another party. RINGER ON/OFF The CP-2070 is shipped with the handset RINGER ON/OFF SWITCH in the ON position and the base RINGER OFF/LOW/HIGH SWITCH in the HIGH position. You can independently set the ringers of the CP-2070. DIALING STORED CALLER ID NUMBERS The CP-2070 allows you to place calls using stored Caller ID information. NEW 10 1 2 C If a second call comes while you are on the phone, your CP-2070 will beep. You can now view the LCD screen to see the name and number of the incoming caller. You can decide whether to answer the second call or ignore it and continue with the first call. If you choose to take the second call, press FLASH to answer it. You may continue to press FLASH to switch between the two calling parties indefinitely. 1 2 3 4 5 Press CALLER ID. (You may press TALK first if you wish. Caller ID can be dialed from off hook mode or on hook mode). Locate the desired numbers by scrolling through saved Caller ID information using the DOWN or UP ARROW KEY. (Holding down the DOWN or UP ARROW KEYS will automatically fast scroll through Caller ID records). Press SEND. If your area code is set to 000 in the CP-2070 the LCD will display the first of the three different dialing options. Press the UP or DOWN ARROW KEY to view the rest of the dialing option. Select one of the three dialing options and press SEND again. The CP-2070 will automatically establish a dial tone and place the call. HANDSET / TELEPHONE OPERATION STANDBY MODE HANDSET VOLUME CONTROL Whenever the CP-2070 is in "Talk" mode, the handset volume will be displayed. 1 PROGRAM. 2 AUTODIAL. 3 KEY LEFT RIGHT ARROW 4 UP ARROW KEY 5 6 Press Press Press the or to locate a memory location. Press the the cursor to the name field. Press the The entire phone number will flash. When the entire phone number is flashing, entering a number on the keypad will erase the previously stored phone number from the display and replace it. AUTODIAL LEFT RIGHT ARROW 5 6 UP ARROW KEY. E Use the DOWN or UP ARROW KEY to select the Caller ID entry you wish to save. TRANSFER REDIAL NUMBER TO AUTODIAL MEMORY This feature allows you to transfer a phone number from the Redial Memory directly into the Autodial Memory. If you wish, you can add a name before you complete the transfer. You can either save the entry exactly as it appears, or you can edit the name and/or number. To save the entry without any editing, just press AUTODIAL. To edit the entry, press the UP ARROW KEY and proceed as described in the "TO EDIT AUTODIAL ENTRIES" section. When you are finished, press to exit "Program" mode. If you only wish to change a few digits, press the LEFT ARROW KEY to activate the cursor, and then use the RIGHT or LEFT ARROW, DELETE, and NUMBER keys to make changes. Press the UP ARROW KEY. The entire name will now flash. As in the previous step, entering a number key (for a character entry) at this point will erase the flashing name from the display and replace it. If you only wish to change a few letters, press the RIGHT ARROW KEY to activate the cursor, and then use the RIGHT or LEFT ARROW, DELETE, and NUMBER keys to make changes. Press AUTODIAL once the correct information is entered and your changes will be saved. Press PROGRAM to exit the programming mode. 7 PROGRAM 1 2 3 Follow steps 1-3 under "TRANSFER CALLER ID TO AUTODIAL MEMORY". Press REDIAL. The contents of the Redial Memory will appear in the display. Follow steps 6-7 under "TRANSFER CALLER ID TO AUTODIAL MEMORY" to edit and save your autodial entry. Enter a telephone number on the keypad. to move PROGRAMMING THE CP-2070 PROGRAMMING OPTIONS 1. 2. 3. 4. 5. 6. Ringer Tone Autodialer (see section E) Local Area Code Setting Outside Line Call Waiting Caller ID On-Screen Help F 1 OR The CP-2070 is in "Standby" mode whenever it is idle, waiting for a call. If the handset is in the charging cradle, the display will either be blank 1 Press the DOWN or UP ARROW KEY to adjust the volume during a call. The volume will remain at that level for your next call. DIALING A NUMBER USING THE SEND KEY (DISPLAY & DIAL) Send-Key Dialing is extremely reliable because you can see the number you have entered before actually dialing it. BATTERY CONDITION You can check the power level of the battery to avoid battery depletion. 1 Press BATTERY when the handset is out of the charging cradle. The following display will appear when the battery is fully charged: BATTERY 3 4 Enter the name using the keypad. Pressing a key once displays the first upper case letter on that key. Pressing it repeatedly will cycle through all of the upper and lower case characters on that key. Stop when the desired character appears in the display. The "1" key provides unique characters and icons. Press the RIGHT ARROW KEY to move the cursor one space to the right. Press AUTODIAL again when you finish to save the new entry. Nothing will be stored until the AUTODIAL key is pressed. Press PROGRAM to exit the mode. PROGRAM OPTION 5: CALL WAITING CALLER ID The Call Waiting Caller ID option is factory preset to "OFF." If you subscribe to Call Waiting Caller ID, you should set this option to "ON," otherwise leave it off. 1 If you have new caller ID entries from recent unanswered calls, it will show the "NEW CALLERS" message with the number of new callers at the lower far right of the display screen. Press CALLER ID to view the names and numbers of "New Callers". CALL TIMER About 10 seconds after you enter "Talk" mode, a Call Timer will appear on the display. The timer will automatically be reset whenever you place a new call. NOTES: s The length of time shown on the display is intended only to be an estimate duration of a phone call. CASIO makes no guarantees regarding the accuracy of this timer. s The Call Timer will not be disrupted if HOLD is pressed. The Hold timer (5 minute count down timer) will display and the Call Timer will continue, hidden from view, during any Hold mode. 1 Make sure the CP-2070 is in "Standby Mode". Without pressing the TALK button, enter the number you wish to dial. If you make a mistake, use DELETE to make changes. The last digit entered will be deleted. Each time DELETE is pressed, the previously entered digit will be erased. After you have correctly entered the entire number you wish to dial, press SEND. The CP-2070 will dial the number. SAVING CALLER ID INFORMATION The CP-2070 automatically saves up to 50 Caller ID entries. Any Caller ID information (name, phone number, date, time) that is transmitted will be stored for your reference or use in the autodialer and redial memory. All Caller ID names and numbers are stored in reverse order of receipt (last call is displayed as highest memory number.) If the memory becomes full, the newest entries will be saved and the oldest ones will be erased. 7 8 9 NOTE: s If no button is pressed for 30 seconds during programming functions the LCD will time-out to a blank display. PROGRAM OPTION 1: 1 2 3 4 Press PROGRAM. RINGER TONE You can select one of 4 ringer tones for the CP-2070. Press the UP ARROW KEY five times. The "Call Waiting Caller ID" Option display will appear. Use the LEFT or RIGHT ARROW to turn this option ON or OFF. Press PROGRAM again to finish. KEY As the battery discharges, the stack symbols will disappear, starting from the right. When the battery is low, the display will look like: BATTERY ERASING AUTODIAL NAMES AND NUMBERS NOTE: s If the handset is in "Standby Mode" but not in the charging cradle, the display will go blank after a short time to conserve battery power. 2 TO PLACE A CALL 2 Press BATTERY again or wait a few seconds to leave battery condition mode. 1 2 Pick up the handset and press TALK. The following display will be briefly shown. This display indicates that the handset is establishing contact with the charging cradle. SCANNING CHANNELS... A dial tone will be established. (In this example, CH03 is the current channel number of 60 available channels in your area.) Wait for dial tone and dial the phone number. The number will appear in the display as you dial. VOLUME CH03 REDIAL The CP-2070 remembers the last number you dialed. The redial memory will hold up to 32 digits. Every time you dial a new telephone number, the redial memory is updated with that new number. LAST CALL TIME DISPLAY NOTES: s Charge the battery for 12-15 hours before using. s If BATTERY is pressed while the handset is in the cradle, "CHARGING" will appear in the LCD. RECEIVING CALLER ID INFORMATION IF CALL IS NOT ANSWERED Even if Caller ID calls are not answered, the CP-2070 will automatically store the Caller ID information into memory. If the handset is in the charger, "NEW CALLERS" will appear on the display. This message will stay on the screen and go away after you review the stored Caller ID information. The NEW CALLS count in the LCD indicates all CPID records not yet viewed. The NEW CALLS INDICATOR on the base will light until you have pressed the Caller ID button to review stored Caller ID records. NOTE: s If the handset is out of the cradle, the LCD screen will only say for 5 seconds and then go blank. It will say again if put back into the charging cradle. NOTES: s If you have programmed your local area code into the CP-2070 before using this feature then the CP-2070 will not prompt you for different dialing options. See "Programming the CP-2070" for more information. s If no button is pressed for 30 seconds during viewing of Caller ID information the ...