VDH910 VIDEOCASSETTE PLAYER / RECORDER OWNER'S MANUAL INSTALLATION GUIDE OWNER'S MANUAL/INSTALLATION GUIDE WARNING! THE CLARION VDH910 MOBILE MULTIMEDIA VCR IS DESIGNED FOR REAR SEAT VIEWING OF VIDEOCASSETTES ONLY. THIS PRODUCT IS NOT INTENDED FOR VIEWING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION SINCE SUCH USE MAY DISTRACT THE DRIVER OR INTERFERE WITH THE DRIVER'S SAFE OPERATION OF THE VEHICLE AND MAY RESULT IN SERIOUS INJURY OR DEATH. SUCH USE MAY ALSO VIOLATE STATE LAW. CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED USES OF THIS PRODUCT. If you do not have the required knowledge and experience to successfully complete the installation, we strongly recommend consulting an authorized Clarion Dealer about professional installation options. TABLE OF CONTENTS Introduction...............................................................2 Care and Maintenance ..............................................3 Dew/Heat Sensor Operation .....................................4 Description Of Rear Connectors..................................5 Description Of Controls and Indicators .......................6 Description Of Remote Control ...................................8 Description of On-Screen Programming ...................10 Operating The VDH910 ...........................................14 Recording With The VDH910....................................16 Installation And Wiring............................................17 Troubleshooting ......................................................19 Specifications ..........................................................20 FCC Statement .........................................................20 ABOUT INSTALLATION Installation of mobile audio and video components requires experience with a variety of mechanical and electrical procedures. Even though this manual provides general installation and operation instructions for your new Clarion VDH910 Mobile Multimedia VHS, it does not show the exact installation methods for your particular vehicle. 1 VDH910 VIDEOCASSETTE PLAYER/RECORDER INTRODUCTION The Clarion VDH910 is a full-featured Mobile Multimedia player/recorder specifically created for the mobile environment. It is designed to work with Clarion Multimedia devices and Clarion Video Monitors for a complete video solution for your vehicle. The VDH910 includes the following features: · 4-head VHS Hi-Fi stereo system for high-quality playback of NTSC video and near CD-quality audio tracks. · Microprocessor-based, full electronic-logic control system with feather-light push-button operation. · Motorized front-loading system for fast videocassette loading and removal. · Built-in 12 Vdc operation which eliminates the need to use power supply converters for mobile use. · Front A/V mounted RCA input jacks that automatically switch to LINE2 input when plugged in. · Infrared Remote Control standard for convenient wireless operation. · Diamond Like Carbon Head (DLC) coated tape head drum for extended head durability while lessening tape 2 wear and tape cleaning requirements. · Special effect playback, including slow motion, and 2speed forward/reverse picture search for quick location of a desired video segment. · Digital Auto Tracking for best picture quality. The VDH910 automatically adjusts tracking while playing a cassette. · Dew/Heat Protection System to warn of condensation and high internal temperatures. About The Manual And Warranty To start enjoying your new Clarion VDH910, please read the remaining instructions listed in this manual. Keep all instructions for future reference. This product is covered by a limited warranty (see the enclosed warranty card). Save the sales receipt to protect your purchase and aid in warranty service. OWNER'S MANUAL/INSTALLATION GUIDE CARE AND MAINTENANCE VCR Care · Use a dry cloth when dusting your VCR. · Take care of your remote control. Keep the remote with your cassettes, where it is unlikely to be lost or damaged. · Keep liquids away from your VCR, including beverages and cleaning liquids. Spilling any liquid on the VCR can damage the electronics, resulting in an electrical shock or fire. · If the unit or remote control should become wet, turn off all power and let your authorized Clarion Dealer clean or service the equipment. DO NOT ATTEMPT TO OPEN OR SERVICE THE UNIT OR REMOTE CONTROL. THE INTERNAL PARTS ARE NOT USER-SERVICEABLE. DOING SO WILL VOID THE WARRANTY. · Do not use liquid or aerosol cleaners that can accidentally get into the VCR causing damage or creating a fire hazard. · Do not allow coins, cleaning cloths, papers and other objects to be pushed into the cassette slot. These objects could connect with a voltage point inside the VCR and cause an electrical shock, or may short out parts causing unit failure or fire. Head Cleaning Over time the picture may become blurred, interrupted, or noisy. If dirt has accumulated on the video heads the unit may require cleaning. You can verify this symptom by playing several different videocassettes. If the problem is the same, then the heads need to be cleaned. Please consult your nearest Clarion Dealer for recommendations on cleaning products and service. Operation Precautions · Do not subject the unit to direct sunlight or an extremely hot environment (e.g., closed windows on a hot summer day, direct path of heater vent, etc.). · Avoid using the unit under the following conditions: ­ After extended parking on an extremely hot or cold day. ­ Near strong magnetic fields. 3 VDH910 VIDEOCASSETTE PLAYER/RECORDER ­ In an environment with excessive humidity, dust, or vibration (e.g., off-road travel, etc.). · If the unit has accumulated moisture condensation (e.g., after parking the vehicle outside overnight), allow the unit to automatically remove it through a built-in Dew/Heat sensor. See Dew/Heat Sensor Operation. Videocassette Use DEW/HEAT SENSOR OPERATION · Use only high quality VHS-type (T-30, T-60, or T-120) videocassettes that last longer and provide a better picture. · Always rewind your videocassettes to help maintain tape quality and tape life. · Do not directly touch the magnetic tape surface. Do not splice or disassemble a videocassette. Playing these cassettes may cause damage to the VCR or its tape heads. · Avoid exposing a videocassette to direct sunlight and keep it away from heat sources (e.g., heater vent). · Avoid extreme environments such as high humidity, excessive vibrations or jarring, strong magnetic fields (e.g., speaker magnet, etc.) and dust. · Always place a videocassette back in its case after use. 4 The VDH910 is equipped with a built-in Dew/Heat circuit that automatically detects for moisture condensation and high internal temperature. When activated, the Dew/Heat Indicator will flash and "DEW/HEAT" is displayed on the TV screen. While active, the Dew/Heat Sensor circuit will inhibit the drive section to avoid damaging heads due to sticking tape or high internal temperatures that can cause tape damage. The unit will be powered on, but it will not accept a videocassette. NOTE: If a videocassette was left in the VDH910, press EJECT to avoid damaging the tape during this procedure. If moisture is the problem, leave the power on so the unit can warm up and dry any accumulated moisture. When the Dew/Heat Indicator stops flashing, the unit will return to full operation. OWNER'S MANUAL/INSTALLATION GUIDE DESCRIPTION OF REAR CONNECTORS 2 (Front AV Inputs) using the Remote control. 4 STEREO IN L/R LINE-1 (RCA Jacks) Use a stereo RCA audio cable to connect stereo audio from an alternate A/V source. You can choose either audio source LINE 1 or LINE 2 (Front A/V Inputs) using the Remote control. 5 DC IN 12V (4-Pin Molex) Use the supplied DC power cord to connect the VDH910 to the vehicle's 12-volt electrical system. Figure 1. The VDH910's rear connections. 6 REMOTE SENSOR INPUT (3.5 mm Plug) Install and connect the remote mount IR Sensor (included) to the back of the VDH910 when the player is hidden away or mounted under a seat. 1 STEREO L/R OUTPUT (RCA Jacks) Use a stereo RCA audio cable to connect stereo audio from the VDH910. 2 VIDEO OUT (RCA Jack) Use an RCA video cable to connect video from the VDH910 to the Monitor. 7 RF INPUT (F-Connector) Use with a 75 ohm antenna. 8 RF OUTPUT (F-Connector) Route to 75 ohm TV input. 3 VIDEO IN LINE-1 (RCA Jack) Use an RCA video cable to connect a video input signal to the VDH910. You can choose either LINE 1 or LINE 5 VDH910 VIDEOCASSETTE PLAYER/RECORDER DESCRIPTION OF CONTROLS AND INDICATORS 3 1 245 79 qwe r t 680 Figure 2. The VDH910's and IR Remote controls and indicators (see descriptions on the next page). 6 OWNER'S MANUAL/INSTALLATION GUIDE 1 POWER Button Press to power the unit ON or OFF. 2 EJECT Button Press to eject a videocassette from the compartment. 3 CASSETTE Compartment Insert a videocassette which automatically loads the tape. 4 STOP Button Press to stop any play, fast forward, or rewind mode. 5 RECORD Button Engages the RECORD mode. 6 POWER Indicator Illuminates when the player is powered up. 7 RECORD Indicator Illuminates when RECORD mode is ON. 8 SLP Indicator Illuminates when playback is in Standard Long Play. 9 DEW/HEAT Indicator When illuminated and flashing the PLAY mode is disabled. Press the EJECT function to remove the internal cassette to prevent damage (see page 4). 0 Remote IR Sensor opening q Allows the IR to function through the front of the player. REW Button Press REW to rewind the tape. If PLAY is engaged, press REW to reverse search for a desired video segment. PLAY Button Press button to play the videocassette. FF Button Press FF to fast forward the tape. If PLAY is engaged, press FF to forward search for a desired video segment. Front A/V (LINE2) Video Input Use an RCA video cable to connect video signal from an alternate A/V source. You can choose either video source LINE 2 or LINE 1 (Rear A/V Inputs) using the Remote control. STEREO IN L/R LINE-2 (Front RCA Jacks) Use a stereo RCA audio cable to connect stereo audio from an alternate A/V source. You can choose either audio source LINE 2 or LINE 1 (Rear A/V Inputs) using the Remote control. 7 w e r t VDH910 VIDEOCASSETTE PLAYER/RECORDER DESCRIPTION OF REMOTE CONTROL 12 3 4 5 7 9 0 8 Figure 3. VDH910's Remote Control. 3 POWER Button Press to power the unit ON or OFF. 4 RECORD Button Engages the RECORD mode. 6 q w e 5 FF Button Press FF to fast forward the tape. If PLAY is engaged, press FF to forward search for a desired video segment. 6 REW Button Press REW to rewind the tape. If PLAY is engaged, press REW to reverse search for a desired video segment. 7 8 CHANNEL TRACK UP/DN Buttons While in the TV tuner mode, changes TV Channels up or down. While in STILL mode, adjusts the tape tracking for still frame clarity. 1 PLAY Button Press button to play the videocassette. 9 SHIFT Button Toggles down the On-Screen Menu choice. 2 STOP Button Press to stop any play, fast forward, or rewind mode. 0 ENTER Button Toggles selection of the On-Screen Menu choices. 8 OWNER'S MANUAL/INSTALLATION GUIDE q MENU Button Displays the On-Screen Menu, or changes and exits the On-Screen Menu. · Objects between the VDH910 faceplate or the remote mounted IR sensor will interfere or block IR remote signal commands. Inserting Battery Into The IR Remote Control w STILL/SLOW Button Press once to pause for STILL frame. Press again to advance frame by frame. Press and hold button for SLOW motion playback. 1. Locate the battery compartment on the back of the IR Remote Control. 2. Remove the battery holder and insert one CR2025 battery (supplied), matching polarity as shown on the battery holder (positive side up). 3. Slide the battery holder back into the remote until it locks with a "click". e TV/VCR Button Changes input source selection from VCR to TV tuner. Using The IR Remote Control Inside the vehicle, simply aim the Remote Control directly at the VDH910's faceplate and press any desired button. When direct line of sight is impossible, install the remote mount IR Sensor in the front of the vehicle (see page 14). For best results, also note the following: · Aim the Remote Control from no further than 7 feet away and no more than 3 feet on either side of the VDH910 faceplate or remote mount sensor. · Direct sunlight or very bright light will reduce sensitivity to remote signal commands. Be sure the remote sensor is not located in direct sunlight. Figure 4. Battery Installation for the VDH910's Remote Control. 9 VDH910 VIDEOCASSETTE PLAYER/RECORDER Using Manual Tracking DESCRIPTION OF ON-SCREEN PROGRAMMING ** MAIN MENU ** RECORD SPEED ............. (SP) AUTO REPEAT............... (OFF) AUDIO OUTPUT ..... (STEREO) CHANNEL SETUP VCR OUTPUT CH.......... (3CH) To View Main Menu [SHIFT/ENTER] [MENU] Using the Remote Control, you ...